BT Make Final Adjustments for Faster FTTC Broadban...

BTOpenreach has advised ISPreview.co.uk that their first trial of VDSL Vectoring (ITU-T G.993.5) technology, which could make even faster speeds available to more people on BT’s superfast (‘up to’ 80Mbps) hybrid-fibre (FTTC) broadband network, has been delayed a little but should now begin “within the next few weeks“.
The trial was originally due to get underway by the end of July or early August 2013 (full trial details) but the initial preparations have apparently taken slightly longer than expected. The good news is that Openreach have now finished installing the necessary DSLAM hardware into six street cabinets around Barnet(London) and Braintree (Essex) in England.
A Spokesperson for Openreach told ISPreview.co.uk:
“We’re now making a number of final adjustments and running some further diagnostics to ensure customers on the trial continue to receive a good service before enabling the system. We expect this final work to be complete within the next few weeks.”
VDSL Vectoring is not unlike the noise cancellation technology that you often find in some headphones and works to cancel out crosstalk (interference) on the “last mile” run of copper cable (i.e. between your local street cabinet and home), which could result in a noticeable speed boost.
Some have speculated that Vectoring could push BT’s FTTC service beyond 100Mbps and, with the help of a few other tweaks, possibly as high as up to 200Mbps. But BT’s initial focus will not be on raising the headline rate and they instead envisage it being used to improve existing performance to more users; especially for those on longer lines where interference is a big problem.
But in order to work effectively Openreach has to enable it on all of the lines that go into a street cabinet, which takes a little longer to deploy. Vectoring might also cause problems for Sub Loop Unbundled(SLU) providers, which could be using incompatible hardware and systems that would make Vectoring difficult to deploy in some areas. Ofcom are investigating this issue as part of their market reviews. On top of that the upgrade also attracts a moderate cost.
In any case the initial trial, once it finally gets underway, is expected to run through September and probably most of November too. Officially Openreach has yet to decide whether or not Vectoring will be part of its long-term strategy but you’d be foolish to bet against it; especially with G.Fast (think of this as FTTC2) being mentioned for their long-term plans.

That is a report from June so a bit out of date.

Similar Messages

I have vision issues and I find myself having to adjust the the page to a larger setting by zooming or using the control+plus feature on my keyboard to inlarge the page.Is there a way I can make these adjustments permanent for every page I link to?

I just upgraded to Windows 7 and since then I have to enlarge the screen every time I go to a new page.I need to make these adjustments permanent if possible.Thanks.
P.S. Could this be a Microsoft phenomenon?
IE doesn't do it,but Firefox and Google Chrome does.

There are some add-ons that can be used to change the zoom level on all sites, for example:
* NoSquint - https://addons.mozilla.org/firefox/addon/nosquint/
* Default FullZoom Level - https://addons.mozilla.org/firefox/addon/default-fullzoom-level/

Recommendation for fast Mac for databases or way to make Mac faster?

I've currently got a Mac mini 1.83 GHz Intel Core 2 Duo with 1 GB RAM running OS 10.6.8. I'm on a quest to either make my current Mac faster or find the ideal mac for databases. I upgraded recently from 10.5.8 to 10.6.8 in the hopes of making my computer more stable and faster, but things are running slower. No wonder, Activity Monitor hardly shows any green memory. Apple doesn't seem to sell memory for this Mac anymore. So I'm wondering whether it's time to just get a new Mac.
What Mac would you recommend for someone not using videos, music, images on a regular basis? Would you consider any of them to be overkill for mostly running database programs? Or would any particular one be insufficient?
Thanks!

Well, almost correct. This computer is used primarily for work, which typically involves FMP or Excel, a browser, less frequently page layout software, Acrobat, emulators of older Mac OSs, and very rarely videos, graphics or audio files. The original problem that led to this post was with a large Excel file that started going haywire. Troubleshooting that led me to repair permissions, repair disk (nothing wrong), reset all sorts of prefs, and eventually install 10.6. After that install, Excel became extremely slow, and other apps also took much longer to open. So I cleaned up Font Book, got rid of unnecessary widgets, emptied caches, and otherwise tried to streamline things. The only startup item I have is for the printer. The other day I realized that Firefox is guzzling any memory that looks free to it, even if I don't have 50 tabs open. Followed steps recommended by Mozilla to solve that, but it seems to guzzle even more now (over 450 MB with 2 tabs open). I don't have Cocktail or Onyx, but maybe that would be the place to look next. I'll try resetting PRAM & SMP next.
I do want to start backing up the files I'm currently working on on an hourly/weekly basis, if not the whole HD. I've been lazy about that. Since that will involve buying an external HD, I've been putting it off to see whether it's worth it to stick with this computer (and get an HD with Firewire 400) or wait & get an HD with Thunderbolt. I dropped in at the Apple store yesterday to look at the new Macs, and they seem to be running fine without any memory guzzlers (even on those with just 2 GB), though the app startup time was a bit slow.
OWC looks great; I'd just have to either find a Swiss equivalent or wait till my next trip back to the U.S., which isn't around the corner.

Final delivery for PO item field, to make optional in transaction codeMIGO

Warm Greetings !!!
Dear Experts your advice to keep the field optional
In transaction code MIGO for the Movement type 101 I want to keep the below field optional
Final delivery for Po item under the Tab Purchase order data
Regards
Shamulheq

Check this link Final delivery for PO item

Help with computer setup and PP settings for faster/better previews

I have been using Cyberlink PowerDirector software for video editing. It is very easy to use and can do quite a bit. It was also accelerated by Intel HD graphics built into my system, so I could see a lot of my work at a pretty high resolution in real time.
However, I wanted to see what PP was capable of, specifically the Warp Stabilizer.
So I downloaded PP and have been trying to use it, but it was just slow as heck to preview anything (chop stop chop stop...), with render times being insanely long (12 hours for five minutes of footage vs. about 30 minutes with PowerDirector).
Thinking it was a problem with my system and I needed to get a real graphics card, I got an EVGA GTX 670 (FTW) for $400, and popped it in. I modified the text file so PP would see it as a compatible card, opened up PP and changed the engine to the new card.
Things are faster, but I was expecting a lot more. Here's what I'm doing:
1. Shooting Canon 5D mark II (now III) clips 20-60 seconds long, 1080p.
2. Import to PP and sequence them.
3. Adding effects:
     A. Top adjustment layer for fast color correction (white balance)
     B. Next adjustment layer: 3-way color, shadow/highlight, unsharp mask, fast blur
     C. Video 1 layer has the clips with warp stabilizer applied to each, and dissolves.
My final output will be 720p. ( I shoot 1080p so the Warp Stabilizer will have more to work with, and I can crop without feeling like I'm degrading quality).
My system: i7 2600k, 16GB RAM, GTX 670 graphics, 120GB SSD "Max IOPS", 2TB 7200rpm internal, 2TB 7200rpm external (USB 2.0, backup drive).
I can currently preview at 1/4 res in realtime. I would really like to be able to get to 1/2 res (of course full would be great). One thing that worries me is that GPU-Z indicates that my GPU is only running at about 2% while previewing, while CPU usage is at around 50%. I was under the impression that the Mercury thing would use GPU/CUDA to process previews and effects that are supported (that includes Warp Stabilizer).
I've looked at Sequence Settings and fiddled with Preview File Format and size, but that doesn't seem to do anything. I'm currently looking around at codecs (Cineform, DNxHD), but don't know if those can help.
What settings should I alter to get better previews?

Well I'm still pretty clueless about this, but for anyone who is looking at this and wondering, here's what I've gleaned:
1. After Effects, especially CS6, makes much more and better use of graphics cards than does Premiere Pro. I'm guessing that PP will, in future versions, make better use of them. For now, no need to spend more than a couple hundred bucks on one.
2. Update the software. PP and AE both performed substantially better after installing the .01 update from adobe. After you install the update, be sure to re-do the CUDA hack, if necessary.
3. As it stands, money for a PP system is best spent on a processor, as in the newest Intel (currently Ivy Bridge), and overclocked. This is where performance happens. I'd say on a 2012 system, 16 GB RAM should be considered a minimum for video editing, and 24 or 32 if you can afford it. More than that probably won't be utilized. Hard disks can affect performance, but I don't think it's a bottleneck unless you're doing something that requires VERY fast/large reads and writes (4k source?). Most people who have high-end editing stations also have a bunch of drives in RAID, but if you look at the performance chart, the SECOND highest scoring tester did not use RAID (though did use a presumably fast and large SSD).
Keep in mind that all of this has to do with RENDER speeds. I still don't know what the bottleneck is for PREVIEWS, but I'm just going to assume it's the same.

Unable to do adjustments for PO Receipt Accrual in Oracle Projects

We are working on Release 11.5.10.
The Allow Adjustments flag for the transaction sources in Projects for receipt accruals (Oracle Purchasing Receipt Accruals) and For Supplier Invoices (Oracle Payables Invoice Variance) are not updatable. Since we are using the Accrue on Receipt option, so only the Invoice variance amount is tranferred to Oracle Projects from Accounts payables. There are situations when the cost gets booked to a wrong task or wrong Project. In such case the adjustments to receipt accruals and Invoice Variance needs to be done. But the same cannot happen in Oracle projects without enabling the Allow Adjustments flag, which is not updatable in Release 11i. How can we make any adjustments to receipt accruals and Supplier Invoices matched with the PO Receipts in Release 11i?
Appreciate any Pointers on this.

Hi
In PO receiving form, enter a transaction of type Correction or Return to Receiving, with minus the quantity you want to adjust. This will be a negative transaction to the original project and task.
Then update the PO line distribution to the new project and task. Finally enter another receipt / deliver transaction to the new project and task.
Run the PRC: Interface Supplier Cost. This process will create new transactions in the old and new projects. The new transactions are linked to the same PO, same line number as the original PO Accrual transaction.
If the supplier invoice have not yet entered in AP, then entering a supplier invoice, matching to the PO will get the variances charge to the new project.
Other wise, you might want to reverse the matching, and reenter the match to the new distribution.
You could also enter a MIX supplier invoice which has the amount as zero. In such invoice enter a negative distribution line to the old project, and a positive distribution line to the new project.
Dina

How can I make my adodc connect faster to my SQL Server? It's taking a minute (so long) before I can view thousand of record in my listview.

How can I make my adodc connect faster to my SQL Server? It's taking a minute (so long) before I can view thousand of record in my listview. Please anyone help me.
I'm using this code:
Public Class McheckpaymentNew
Private cn As New ADODB.Connection
Private rs As New ADODB.Recordset
Private Sub McheckpaymentNew_Load(sender As Object, e As EventArgs) Handles MyBase.Load
Try
cn.ConnectionString = "DSN=database; UID=user; PWD=password"
cn.Open()
rs.CursorLocation = ADODB.CursorLocationEnum.adUseClient
rs.CursorType = ADODB.CursorTypeEnum.adOpenStatic
rs.LockType = ADODB.LockTypeEnum.adLockBatchOptimistic
Catch ex As Exception
MsgBox("Failed to Connect!, Please check your Network Connections, or Contact MIS Dept. for assistance.", vbCritical, "Error while Connecting to Database.."
End
End Try
End Sub
End Class

How can I make my adodc connect faster to my SQL Server? It's taking a minute (so long) before I can view thousand of record in my listview. Please anyone help me.
I'm using this code:
Public Class McheckpaymentNew
Private cn As New ADODB.Connection
Private rs As New ADODB.Recordset
Private Sub McheckpaymentNew_Load(sender As Object, e As EventArgs) Handles MyBase.Load
Try
cn.ConnectionString = "DSN=database; UID=user; PWD=password"
cn.Open()
rs.CursorLocation = ADODB.CursorLocationEnum.adUseClient
rs.CursorType = ADODB.CursorTypeEnum.adOpenStatic
rs.LockType = ADODB.LockTypeEnum.adLockBatchOptimistic
Catch ex As Exception
MsgBox("Failed to Connect!, Please check your Network Connections, or Contact MIS Dept. for assistance.", vbCritical, "Error while Connecting to Database.."
End
End Try
End Sub
End Class

Can you make custom clothing for 3d Models?

Hello, I am new to Photoshop CS5 Extended and mostly bought the program for making textures for 3d clothing since it has a bridge from DAZ to Photoshop which I hope will make my work go faster. I have been using DAZ and Poser for a while now and have been working in photo editing and vector designing for 12 years. I am not new to this, just need to adobe products. I was wondering if it is possible to custom clothing for 3D Daz models using Adobe Photoshop CS5 Extended? I can find tutors on painting models but nothing on making the custom clothing itself, not a texture for other clothing but making my own clothing for DAZ Kids4. I have been using Hexagon to work with clothing but was looking for a photoshop alternative method.
Thank you
Kimberly

for the mesh, hexagon is actually better than photoshop. Since it can create the actual mesh. Though, you can import the mesh into photoshop so you can see it while you paint the texture.
The 3d creation portion of photoshop is still a bit limiting. (But my experience stops with CS5. I have not tried CS6 yet, so impovement could have been made)
The issue I have with hexagon is the amount of bugs in it. I prefer a more robust and more expensive alternative. But thats me
A free alternative is Blender. But I find the UI a bit outdated and hard to grasp. But again, thats me.
Generate your UV maps as you normally would then load them into photoshop and get painting. You may like other texture generating apps to go along with photoshop. Genetica is great for making tileable textures.

How Can i clean my memory and make my imac more faster ?

I am new user in mac i have imac 4 g ram and need a way to clean the memory and make my imac more faster ...

You can't "clean" RAM. If the "storage" space on your hard drive isn't enough then put in a larger hard drive or delete any of your data you no longer need or can store on an external drive. Beyond this I cannot say because you have not provided enough information such as the amount of installed RAM, Capacity of your hard drive and the amount of available space on the hard drive, the specific iMac model you have.
You can try reinstalling Lion:
Reinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.
However, if your computer doesn't have enough RAM or your hard drive is full, then reinstalling won't help.

Does iWeb automatically compress photos for faster loading? Or should I do it first? Thx

Hi everyone, when I look at the large photo in the "white" theme's Welcome template, I wonder when I drag and drop one of my photos in, does iWeb compress the photo for faster loading? Or should I compress them before adding to site?
By "compress" I mean, make photo file size smaller! :)
Thx! :)

In iWeb Preferences you can optimze images on import. But I always scale most of my images to 800 x 600 pixels prior to importing. I do this in Graphic Coverter which also makes the image files smaller by taking unneeded information out of the file, which also reduces the file size.
In Graphic Converter

Is it necessary to "clean" your Mac? I'm not s but I've been getting ads about cleaning your Mac. What does it do? Would it make surfing the web faster? thanks

HI, is it necessary to "clean" your Mac? I'm not sure what that means or what it does but I've been getting ads that offer to clean it. Would doing that make surfing the web faster? Thanks!

Suggestions for Mac maintenance
Make redundant backups, keeping at least one off-site at all times. One backup is not enough. Don’t back up your backups; make them independent of each other. Don’t rely completely on any single backup method, such as Time Machine.
Keep your software up to date. Software Update can be set to notify you automatically of updates to the Mac OS. Some third-party applications have a similar feature, if you don’t mind letting them phone home. Otherwise you have to check yourself on a regular basis.
Don't install crapware, such as “themes,” "haxies," “add-ons,” “toolbars,” “enhancers," “optimizers,” “accelerators,” “extenders,” “cleaners,” “defragmenters,” “firewalls,” “guardians,” “defenders,” “protectors,” most “plugins,” commercial "virus scanners,” or "utilities." With very few exceptions, this kind of material is useless, or worse than useless. The more actively promoted the product, the more likely it is to be garbage. The only software you should install is that which directly enables you to do the things you use a computer for — such as creating, communicating, and playing — and does not modify the way other software works. Never install any third-party software unless you know how to uninstall it.
The free anti-malware application ClamXav is not crap, and although it’s not routinely needed, it may be useful in some environments, such as a mixed Mac-Windows enterprise network.
Beware of trojans. A trojan is malicious software (“malware”) that the user is duped into installing voluntarily. Such attacks were rare on the Mac platform until recently, but are now increasingly common, and increasingly dangerous. There is some built-in protection against downloading malware, but you can’t rely on it — the attackers are always at least one day ahead of the defense. You can’t rely on third-party protection either. What you can rely on is common-sense awareness — not paranoia, which only makes you more vulnerable. Never install software from an untrustworthy or unknown source. If in doubt, do some research. Any website that prompts you to install a “codec” or “plugin” that comes from the same site, or an unknown site, is untrustworthy. Software with a known corporate brand, such as Adobe Flash, must be acquired directly from the developer. No intermediary is acceptable, and don’t trust links unless you know how to parse them. Any file that is automatically downloaded from a web page without your having requested it should go straight into the Trash. A website that claims you have a “virus,” or that anything else is wrong with your computer, is rogue.
Relax, don’t do it. Besides the above, no routine maintenance is necessary or beneficial for the vast majority of users; specifically not “cleaning caches,” “zapping the PRAM,” “rebuilding the directory,” “running periodic scripts,” “deleting log files,” “scanning for viruses,” or “repairing permissions.” Such measures are for solving problems as they arise, not for maintenance. The very height of futility is running an expensive third-party application called “Disk Warrior” when nothing is wrong, or even when something is wrong and you have backups, which you must have. Don’t waste money on Disk Warrior or anything like it.

I want to use camera raw to make color adjustments after using Ps5 levels.

Pc win 7 cs5. I like the control I get using the Hue/sat controls in Camera raw. However, I like to set Levels in Ps first. No matter what format I use to save the image after Ps adjustments, I am no longer able to open the image in camera raw. I've tried using ctrl+r shortcut, and have tried changing preference to "Handle all Tif files" and " All Jpeg files" in Camera Raw preference dialog. It seems I can only Open a CR file in Camera raw. I believe I have used Camera Raw to edit other formats before, I may be wrong.

How about opening your file in ACR first and making adjustments, then open as Smart Object in Photoshop? Hold down the Shift key to open the image as an Object in PS
You can then create additional layers, but you can also double click the SO layer in Photoshop at any time to go back to ACR where you can make more adjustments and then return to Photoshop.
As long as you keep the SO layer in PS you can go back to ACR as many times as you want.
Just be aware that any adjustments that you do in PS will NOT be reflected in the SO when reopened in ACR.
Depending on what you are doing this may work well for you or it could be frustrating. Try it and see if it works for your specific image.
Even if it seems to not be helpful for your specific image, it might work very well with other images. (depending on your changes in PS)

When I try to charge the phone it says for faster charge use original cable

Just got my Note 3 late yesterday afternoon. When I try to charge the phone it says for faster charge use original cable and that is what I am doing. Even tried a different charger and it says the same thing so I have not been able to use my phone at all. Please help. I am going back to the store today when they open. Help!!!

I want to help make it as easy possible to charge your device myluv2drive! Is this happening with the original charging cable itself or is this an alternate charger? Have you tried a battery pull since this started? Did this happen the first time you tried charging it? Any different response when trying alternate outlets?
JonathanK_VZW
VZW Support
Follow Us on Twitter@VZWSupport

Main iTunes screen: can't make any adjustments to select-deselect apps,etc

I'm helping a PC friend of mine. He has iPad 2, W7-fresh install, latest iTunes with iPad connected and viewing the contents on main iTunes screen, he can not make any adjustments to selecting apps (putting a check box next to app to include in next sync for ex.) He can not click on the mini ipad desktop screens for each page (along side the right side) to jump to different pages and rearrange icons. WEIRD! I've never seen this on the Mac side.
Almost seems like some type of permissions issue in windows...??? HELP ! ! !

solved it. He was working between 2 PCs and did not "Authorize" under AppleStore menu listing for this new PC.

Trouble with database connector for FAST for Sharepoint

I have plenty of experience with the JDBC connector for FAST ESP using Oracle, but this is the first experience I have with the same connector for FAST for Sharepoint (F4SP). I've created the XML config exactly to specs based on the technet guides
and configured my user accounts on the SQL Server appropriately. I'm using SQL Server 2008 R2.
If I try to use a Windows account, no level of access granted on the SQL Server results in a successful login. Any attempt to use the connector is met with "Login failed for user: domain\username". If I try a SQL Server account, I no longer
see a login failure, but this instead:
PS C:\FASTSearch\bin> jdbcconnector start -f ..\etc\DTtest.xml
Copyright (c) Microsoft Corporation. All rights reserved.
14:44:59,870 INFO [JDBCConnector] Starting the connector!
14:44:59,870 INFO [JDBCConnector] Validating config.......
14:45:00,136 INFO [JDBCConnector] Testing connections to external systems
14:45:00,198 INFO [JDBCConnector] Checking if connections to source and target work....
14:45:00,620 INFO [JDBCAdapter] Opened JDBC Connection
14:45:00,620 INFO [JDBCConnector] Connection made to source system
14:45:00,620 INFO [CCTKDocumentFeeder] Publisher :Initializing: com.fastsearch.esp.cctk.publishers.CCTKDocumentFeeder
14:45:00,620 ERROR [JDBCConnector] Failed creating publisher. Test connection failed.
14:45:00,620 ERROR [JDBCConnector] Caused by: Unable to create status tracker.
14:45:00,620 ERROR [JDBCConnector] Caused by: Could not connect to database. Make sure TCP/IP is enabled for SQLServer.
14:45:00,620 ERROR [JDBCConnector] Caused by: No suitable driver found for ;integratedSecurity=true
14:45:00,620 INFO [JDBCConnector] Connection made to target system
TCP/IP is certainly enabled for SQL Server -- I am connecting to it with Sharepoint 2010, not to mention a test install of Toad Freeware for SQL Server from another machine, resulting in no errors. My connection string, username and password are all
set up according to the technet guide, including the encrypted password set by the encryption utility run the in F4SP Powershell. The same user who runs the connector also ran the encryption tool, so that should not be a problem either.
I've never had this kind of trouble connecting to Oracle databases with the JDBC connector for FAST ESP. Any suggestions? These failures aren't exactly helpful to me. Thanks in advance.

I found the solution to this problem in case anyone else was still curious.
This was caused not by JDBC settings, permissions/access on SQL Server, etc. It was caused simply by a missing SQL Server in F4SP configuration. When you run the F4SP config wizard, either as single-node or multi-node installations, the wizard
might end up ignoring the value you select for SQL Server, even if you are using a deployment XML file. When configuring as a multi-node setup, the wizard ignored both my deployment XML tag <connector-databaseconnectionstring> and the SQL Server
setting done manually in the wizard itself. Examing the evidence, I suspect this was caused by corrupt installation media (since the installer also failed to create some core files in /etc upon doing a reinstall).
The bottom line is that you must see a value for SQL Server in your install_info.txt file in order for the JDBC connector to work with SQL Server, like this:
Other services
Log Server:             myserver.mydomain.com:13415
SQL Server database:    jdbc:sqlserver://myserver.mydomain.com;DatabaseName=FASTSearchAdminDatabase;integratedSecurity=true
If you see this instead, the connector will never work:
So, the JDBC connector is certainly dependent on the main configuration of F4SP, regardless of what SQL Server is targeted in your connector's XML configuration.
Other services
Log Server:             myserver.mydomain.com:13415
SQL Server database:
;integratedSecurity=true
I had no idea there was a connection between my install_info setup and the use of the JDBC connector. But, the connection makes sense considering this was the error message from the JDBC connector:
09:20:04,016 ERROR [JDBCConnector] Caused by: No suitable driver found for ;integratedSecurity=true

BT Make Final Adjustments for Faster FTTC Broadban...

Similar Messages

Maybe you are looking for