BT Vision Box and Remote Control not working prope...

Hi,
Can anybody help me please?
I have a black BT Vision Box. The remote control had increasingly been sticking so tonight I just turned the power off tonight, left it off for 20 seconds and turned it back on.
It seemed to turn back on and reboot itself normally, it took the amount of time it normally does on a couple of occasions when it froze a few months back. However since I rebooted it approximately 3 hours ago it has been turning itself off and rebooting itself every 10 minutes or so. On one occasion when I turned it off on the front of the machine and left it for a few minutes, it turned itself on and started rebooting itself again. 
The remote control is worse than when it was sticking, now there is a delay of up to 30 seconds after I press a button. Sometimes it does not work at all, when that happens it just becomes stuck and eventually reboots itself.
So far I have tried turning it off and on again, I have also tried rebooting the internet connection (which is working fine). I have tried pressing the off button on the actual box for 10 seconds and resetting it that way. I have put new batteries in the remote. Nothing has worked. If anyone can help me that would be great.
Solved!
Go to Solution.

Hi, 
Unfortunately I can't get that far now.
I turned all TV related systems off last night in an effort to see if it would work properly today.
I came home from work and turned everything on. The system boots itself up until it gets to a grey screen that says "Nearly there..." with the BT logo in the bottom right corner. It stays like that for approximately one minute. Then it turns itself off and starts rebooting itself again. 
I have tried pressing the on/off button on the front of the box and holding it in for 10 secs or so until the box turns itself off and reboots but the effect is still the same as above. 
Do you have any other suggestions pleaase, aside from throwing it in the bin?

Similar Messages

  • Remote control not working on Touchsmart 610-1030uk

    Had been working fine for long time. Now out of warranty. Battery fine. Indicator on remote and on PC (white LED on front panel) both show IR is working. Mouse and keyboard still work fine. I have tried uninstalling and reinstalling drivers for Microsoft eHome infrared transceiver but still can't get the machine to respond to remote control. 
    Any thoughts?
    This question was solved.
    View Solution.

    Hello frrw. Sorry to waste your time. I changed the batteries and it works fine. It seems the red LED on the remote and the white LED on the PC that flashes when I press a button on the remote do not mean that the batteries are strong enough. 
    Meanwhile I have that recurring problem with blu-ray players. I will post a new question and maybe you can help. 
    Many thanks. 

  • Win2k8 Remote Control Not Working With SRSS 4.2 + SRWC 2.2

    Hi there.
    I have an install of Windows Server 2008 (32bit) with SRSS 4.2 & SRWC 2.2 setup. I was previously on SRSS 4.1 & SRWC 2.1 and having the same issue I am having now, which to me tells me this problem is unresolved or i'm being a total muppet. (hopefully not the last one)
    Windows Terminal Server environments has this awesome remote control feature where you can login to an RDP session which is already active and take control of the session while the end user is still logged in.With Server 2003 this works perfectly fine- it's brilliant. WIth 2008 it is a nightmare. It works for a split second and then closes off. The end users session also gets locked out (not logged out) and they have to put their windows credentials in to carry on working again.
    Now... I can remote control users who are logging in via Remote Desktop on Windows XP/Vista etc.. but I can't with the Sun Ray Sessions. Does the SRWC 2.2 fully compatible with RDP 6.1 or is there any information anyone can give me to point me in the right direction of resolving this issue, like I said.. Win 2k3- Works like a dream....
    Any help would be greatly appreciated.
    Regards
    - Joe.

    I just realised I hadn't posted the logs from SRSS Server with the issues. I have just tried on another WIN2K8 Server which wasn't configured by myself or my company and the same symptoms occurred. See logs below:
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4095]: [ID 702911 user.notice] /opt/SUNWuttsc/bin/uttsc[104]: 4116 Abort
    Oct 1 10:58:06 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4117]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4123]: [ID 702911 user.error] /opt/SUNWuttsc/bin/uttsc exited with error code 134 - exiting
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcrit: [ID 702911 user.notice] Info: critical application uttsc (pid=3902) exited with non zero status: 134
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 422571 user.info] Info: a critical application has exited.
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 126805 user.info] Terminating Kiosk Primary Session ( pid=3902 )
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 308018 user.info] kioskcritd stopped
    Oct 1 10:58:07 ESL-SOLARIS-SPARE utauthd: [ID 794400 user.info] SessionManager0 NOTICE: EMPTY: ACTIVE session
    Oct 1 10:58:15 ESL-SOLARIS-SPARE kiosk:utkioskconfig:refresh[4381]: [ID 702911 user.info] Enabled Kiosk Mode for display ':2'
    Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 118685 user.info] pam_sunray_amgh::[DPY=2] AMGH_SUMMARY: token=pseudo.00144fb78760, username=, AMGH_Done?=NO(Local Session), Details=AMGH is not configured., AMGH_Target=*NONE*
    Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 976841 user.info] pam_kiosk: pam_sm_authenticate: Initiating Kiosk session with user utku2
    Oct 1 10:58:15 ESL-SOLARIS-SPARE kioskcritd[4420]: [ID 190395 user.info] kioskcritd started
    Oct 1 10:58:57 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4612]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
    Anyone able to help me out?

  • Drag and Drop Control Not Working - IE 11

    A user with MS Office 2013 properly installed/configured and 32-bit Internet Explorer, is getting an "x" in place of drag & drop control while uploading files to SharePoint document library. What could be the problem?
    Any pointers?

    User is using Internet Explorer 11. I have attached all the relevant screenshots. I also asked him to check the following settings and attached is a response:
    ==================
    Option 1: From the Tools menu in the Internet Explorer (the "gear" icon) select Internet Options.
        Select the Security tab.
        Click Local Intranet as the zone to change.
        Click Custom Level. The Security Settings - Internet Zone dialog box appears.
        Scroll down to the options below Internet ActiveX Controls and Plugins and ensure the below options are enabled:
        1. Run ActiveX Controls and Plugins
        2. Script ActiveX Controls Marked Safe for Scripting
    Option 2: Launch Internet Explorer from: C:\Program Files (x86)\Internet Explorer\iexplore.exe
                      Does it work?
    Option 3: Ensure that the following DLLs are present:
                        C:\Program Files (x86)\Microsoft Office\Office14\STSUPLD.DLL
                        C:\Program Files (x86)\Microsoft Office\Office12\STSUPLD.DLL
                        C:\Program Files (x86)\Microsoft Office\Office11\STSUPLD.DLL
    =============
    Option 1: All Enabled
    Option 2: Not working
    Option 3: See below:
    Any thoughts or pointers?

  • XFI-64 Bit Driver, remote control not work

    I have just installed the 64Bit drivers for my X-fi Fatality. The sound works however the 'sound console' that plugs into the dri've bay at the front of my pc does not seem to be working. I press start on the remote control and nothing happens. The X-fi volume icon does not appear in the system tray. When I boot up the 32 bit version of windows all is well and i can use the remote control and all of its functions. Can anyone help as this is now very frustrating.

    Originally Posted by MiLoCzE
    Hi men, if you will use remote control, you must install ECUP_PCVTAPP_LB_3_40_21 . :-)
    What is " ECUP_PCVTAPP_LB_3_40_21 " ?
    I searched on the internet and all I could find about it is that it's a virus? Can you tell me something more about that file ?
    http://www.pc-face.com/exe-file-erro...exe-fix-22694/

  • Audigy 2 ZS Platinum - Remote Control not work

    hello all.. Sorry for beating a dead horse. My installation on a P4 3.0 ghz machine of the Audigy 2 was flawless. All hardware diagnostics that have been run have been successful. Everything works. I updated all drivers. Everything is functional on the unit.....but...the remote control doesn't work.
    When I got to setup the remote control and it asks to select a transmitter (rm-500) from a drop down list, it shows rm-500. but it the drop down list for the receiver is BLANK? I've tried several suggestions from the forum but it still doesn't work.
    Have I missed something or is it quite possibly just a dud unit that I have to take back.
    thanks for all suggestions and ideas...
    sony

    OK, let's see, you have a device that is still under warranty. You properly installed said device. You put batteries in the remote but it does not work no matter what you try. It seems to me that you have only one option and you mentioned it in the penultimate sentence in your post.
    Hope it's not a long dri've.:smileyvery-happy:
    Richard
    Message Edited by sf3454 on 03-3-2005 03:28 AM

  • Remote control not working

    The remote control for one of my TVs is not working. We inserted new batteries and also checked all cable connections. We tried one of the other remote controls and the TV responded. How do we get a new remote control ?? We tried calling ATT but could not get through.
    Thank you in advance
    Mojo612

    The original remote is not controlling the TV or the STB or both?
    Try pressing the att button, then see how it works.
    The two TVS are the same? They both use the same IR.

  • Why isn't my bluetooth keyboard volume and play controls not working osx x

    For some reason my top row keys are not working on my bluetooth wireless keyboard well the work but the volume up key switches to the dashboard, the volume down triggers the expose' ... it just all out of wack. Please help!!
    Thanks in  Advance,
    Marc

    Hello:
    There was an update that addressed that issue in older versions of OS X.  However, your profile indicates you are running OS X 10.7.3.  Is that correct?
    Barry

  • TS1741 Apple TV remote- no physical remote and remote app not working. ?

    Hi I've just got a new wireless network and my Apple TV is not connected to it, error message  when I go to tv channel for Apple TV.  Error telling me to go to settings etc and connect which is fine.  Issue is I have no physical remote and  I had the remote app downloaded but it is not connecting to Apple TV, keeps prompting for. Home sharing which I have/had already activated but won't allow me to interact with Apple TV .. How do I get Apple TV connected to new network and get remote working??

    You need the hardware remote.  You can not enable the remote app without it.  You can buy a replacement for $20.

  • Bookmarks bar and tab controls not working in mobile Safari on iPad2

    The bookmarks bar as well as tab controls in Mobile Safari on iPad 2 are not clickable. Only the topmost nav buttons work. This persists through reboots w/Safari closed via mem manager, and a system restore. What do?

    closing Safari via the taskbar
    or having done a reset (unless that is what you mean by a reboot)
    "This persists through reboots w/Safari closed via mem manager"
    That is obviously exactly what I meant. How does one reboot an iPad without "resetting" it? How does one do a system restore without "resetting" it?

  • Broke out of the box and itune update not working

    Just got apple tv delivered today but it wasn't working out of the box... flashing white light..
    So i connected it to itunes via micro usb and itunes won't restore it looks like the .dmg is missing..
    This is really bad, surely apple have noticed the software update is missing???
    Did this update work for anyone?

    It's impossible to know how much work there is putting it back, it sounds simple but it might not be, it's been down a few days now, I suppose it depends on how much inconvenience it is to return it for another.

  • ITunes wireless sync and Remote App not working in in unison.

    I'm running iTunes on a Windows 8 machine, and I'm having issues getting both these above mentioned applications working together.
    I did have some issues in the beginning with setting up wireless sync for my iPhone, but these were fixed by restarting the Apple Mobile Device Service that runs in the background.
    The remote application seemed to have similar issues in the beginning, so I tried restarting the Apple Mobile Device Service - and this seemed to help, but then wireless sync faulted again.
    After having a bit more of a read, I made sure UPnP was enabled across the board - in my PC and router, SSDP on my PC was changed to automatic mode, all bonjour services were confirmed running and there and I couldn't see any funky rules in my firewall that may be causing me issues.
    I did find though, that both the remote app and the wireless sync functions operate on the same ports; TCP port 3689 and UDP port 5353. I'd imagine if this would be a problem, it would have been picked up - but I can't find any solid info to disregard this thought. Can anyone confirm or deny that this could be an issue?
    Any other ideas? Cheers.

    Welcome to the Apple Community.          (5)
    The following article(s) may help you.
    Troubleshooting Home Sharing
    Troubleshooting Wi-Fi networks and connections
    Recommended Wi-Fi settings

  • Touch contol pad for volume,pause and play controls not working (pavilion dv7 3020sa)

    The touch pad controls light up but i cannot use them, i cann not adjust the volume or press play or turn the wifi on or off. not responding to touch at all....can anyone help ???

    Have you tried updating your drivers?

  • N8 Video Player and Photo Viewer not working prop...

    Hi I just got a N8 a few months ago and its been going great until a month ago. 
    My video player is not displaying any the videos that I had on the phone or any of the videos I try putting on after. I then tried the photo viewer (it displays video as well for some reason) but that didn't have any of the videos and only some of my photos are being displayed.
    I previously had the problem with the music player where it would be stuck on  the music updating screen (not frozen) but I solved that by looking through the net and finding that you delete a certain file and it fixed that.
    Thanks  

    Haven't figured it out yet, but will post if I find a solution.
    The problem is, I'm trying to find a solution to a whole host of other problems on my N97, e.g. The problems I'm having with GPS (Maps 2 and 3 are both currently unusable), the problems I'm having getting my widgets, email etc to detect which connection I need using etc, the problems I'm having with reception, the problems I'm having with my ringtone etc. So this photo viewer problem is just another issue to add to the list.
    As for the Facebook App, if I take a picture using the camera link within the application, it won't let me upload anyway, so I've stopped using it. I just use the standard Facebook Mobile site as the Nokia Facebook App is so slow, it's borders on useless.

  • Device not working after updating from 8 to 8.1: SMK Ehome Infrared Transceiver and remote control (usb)

    Hi all,
    An excellent 2015 to you all. 
    I wonder whether it's possible to get my (USB) SMK Ehome Infrared transceiver (which serves to connect my PC to a remote control)  to work again. It functioned okay under Windows 8, but when I upgraded my system to Windows 8.1 it didn't respond anymore.
    How's that possible? And do you have any ideas how I can resolve this?
    I use the remote control to start and stop videos and to adjust the sound volume.
    What I have done already:
    -disabled and enabled the consumer IR devices under 'HID devices' in device management.
    -disabled and enabled the USB controller for the Ehome Infrared Receiver.
    No luck so far. Anybody knows what to do?
    Cheers,
    Peter

    Hi,
    What is the driver status in device manager? Have you tried to manually download the right version driver for Windows 8.1 from the transceiver's manufacture website and install it in your system?
    Meanwhile, please run services.msc to launch services manager, then scroll down to "Human Interface Device Access service", make sure the service is "started" to "manual" or "automatic", test the issue again.
    Yolanda Zhu
    TechNet Community Support
    Thanks, Yolanda Zhu. There is no driver on the manufacturer's website, but the driver is included from  Windows versions XP to 8 and the device responds as expected under these OS Versions. In Windows 8.1 it seems also to be included, and device manager
    indicates under Human Interface Devices that the 'Microsoft eHome infra transceiver' driver  functions correctly and under
    Universal Serial Bus controllers that 'eHome infrared receiver' (USBCIR) functions correctly as well.  But when I press the remote, the red LED blinks, but nothing else happens.
    The "Human Interface Device Service" is set to automatic and is being executed.
    Can it be that the mapping ('action on remote' to 'action on PC') is lost somehow?
    Cheers,
    Peter AKA Django

Maybe you are looking for