BTU for Cisco 3925

Can anybody confirm the BTU for Cisco 3925? I did search but not clear on the findings..

Hello,
Unfortunately this part is EoS and not supported on 3900. You can see this information here (look for  Table 5.
Unsupported Modules on ISR G2 - Cisco 1900, 2900 and 3900 Series routers):
http://www.cisco.com/en/US/prod/collateral/routers/ps10538/aag_c07_563807.pdf
Hope this helps,
Nik

Similar Messages

  • RME 4.3.1 Inventory collection failing for cisco 3925

    Hi,
    I've a customer having LMS 3.2 and RME 4.3.1. He has 14 Cisco 3925 routers out of which inventory collection for 2 fails.
    Router IOS is: c3900-universalk9-mz.SPA.150-1.M.bin".
    Can someone suggest what might be going wrong? Attached is the  IC_Server log file for reference.
    Thanks in advance,
    inner_silence

    Hi,
    Here are the exception found from the log :-
    [ Fri Mar 18  16:28:24 EDT 2011 ],ERROR,[Thread-17],com.cisco.nm.rmeng.inventory.ics.core.CollectionController,729,Exception for device 10.103.251.12 is
    java.lang.reflect.InvocationTargetException
        at sun.reflect.GeneratedMethodAccessor12.invoke(Unknown Source)
        at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
        at java.lang.reflect.Method.invoke(Method.java:585)
        at com.cisco.nm.rmeng.inventory.ics.core.CollectionController.run(CollectionController.java:719)
        at java.lang.Thread.run(Thread.java:595)
    Caused by: com.cisco.nm.xms.xdi.ags.system.CollectionFailed: java.lang.StringIndexOutOfBoundsException: String index out of range: 2
        at com.cisco.nm.xms.xdi.pkgs.LibInventory.EnergyWise_HelperMethods.getDeviceEnergyWise(EnergyWise_HelperMethods.java:72)
        at com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.EnergyWiseAGI_ENERGYWISE_Mib.g$eval(EnergyWiseAGI_ENERGYWISE_Mib.java:51)
        at com.cisco.nm.xms.xdi.ags.EnergyWiseAGI.g$eval(EnergyWiseAGI.java:21)
        at com.cisco.nm.xms.xdi.SdiEngine.initAndEvalAGIs(SdiEngine.java:383)
        at com.cisco.nm.xms.xdi.SdiEngine.request(SdiEngine.java:309)
        at com.cisco.nm.xms.xdi.SdiEngine.getDevRepr(SdiEngine.java:302)
        at com.cisco.nm.rmeng.inventory.ics.core.CollectionController.run(CollectionController.java:539)
        ... 1 more
    [ Fri Mar 18  16:28:24 EDT 2011 ],ERROR,[Thread-17],com.cisco.nm.rmeng.inventory.ics.core.CollectionController,761, Collection failed for the device : 63
    com.cisco.nm.xms.xdi.ags.system.CollectionFailed: java.lang.StringIndexOutOfBoundsException: String index out of range: 2
    Kindly check if the your device is running the required IOS on the device as per the device supported list :-
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html
    There are two 3925 listed with different versions :-
    Cisco 3925 Integrated Services Router   --> 1.3.6.1.4.1.9.1.1042  --> 15.0(1)M [RME]. if this is your device then upgrade to
    3925 to 150-1.M2
    and
    Cisco 3925E Integrated Services Router  --> 1.3.6.1.4.1.9.1.1144 --> 15.1(1)T
    Thanks,
    Gaganjeet
    If this post answers your question, please click the "Correct Answer" button

  • Security License for Cisco 3925

    Hi,
    I have got cisco 3925 without security license. Now I have got the L-SL-39-SEC-K9 license and need to install it. What is the process of installing this license.
    Thanks in advance
    Regards,
    Mero

    Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
    Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
    HTH
    Alexandr

  • Enquiry on RMA for Cisco Products

    Hi,
    Recently i ran into some issue when processing a RMA for Cisco 3925 router.
    I've RMAed the chassis but the i got the part, it didnt have a system board.
    When i contacted Cisco, they mentioned that the system board can/must be RMAed separately.
    Is there any documentation or list for Cisco Products that has system board as a FRU?
    Thanks

    Recently i ran into some issue when processing a RMA for Cisco 3925 router.I've RMAed the chassis but the i got the part, it didnt have a system board.
    Before the replacment part/unit is shipped, you always get a shipping document in an email.  This document will list down what item(s) are being shipped.
    Did you get this?

  • Cisco 3925 Enhanced EtherSwitch Service Module

    Hello all,
    I have a Cisco 3925 router with a SM-ES3G-16-P Etherswitch module. In order for me to access it, I need to put an IP address on the phyiscal interface its attached to. Then I can access it via the service-module command.
    My question is -- does it matter what address I give it? Does it need to be a legitimate management address on my network so that I can access it directly from another switch? Or do I always need to go through the router and issue the service-module command? If I do need to always go through the router, I should just be able to give it a 10.10.10.1 address and that should be enough, right?
    Thanks for your help in advance,
    Bobby Grewal

    Thanks Reza...one more question. how does the switch module actually talk to the 3925 router? Through port 17 or 18? If so, do I need to configure those interfaces as routed ports within the same subnet? Or are they just trunks? All connections within the switching module would need to talk to outside devices.

  • Configuring IP SLA in cisco 3925 router.

    HI Team.we need to configuring IP SLA in cisco 3925 router with c3900-universalk9-mz.SPA.151-4.M4.bin ios. For Monitoring purpose. Earlier we have used the rtr command for the same. Now we are going with new Cisco 3925 router. with the above mentioned IOS. Pls suggest whether we can configure the IP SLA in the router with Licence. Or We need to buy the licence for the ame.
    Posted by WebUser Ramkumar Selvaraj from Cisco Support Community App

    Hi
    I think the command has been updated - rather than 'rtr responder' it's now 'ip sla responder'.
    I don't believe you need any particular feature set.
    Also, this is a 'Contact Center' forum - you would get more responses in other places.
    Regards
    Aaron HarrisonPrincipal Engineer at Logicalis UK
    Please rate helpful posts...

  • Cisco 3925 doesn't work together with TC

    From my provider I got a new modem/router. The cisco 3925. Via this router directly I came almost to 48Mbps. When I put the TC between it I get not higher then around 5 to 7Mbps.
    TC is in bridge mode and both 2.4 and 5Ghz are active.
    Can anybody help me what goes wrong here.
    Thanks.
    Martien

    Firstly if the TC is within warranty ring and get Apple support involved, as frankly I doubt we are going to be able to crack it.
    Sometimes there are actually issues with the TC and needs to be replaced.
    How old is the TC and exactly what model is it? The A number stamped in the rubber mat will tell us enough.
    What firmware is it running? If it was running 7.6 before, flash back to 7.5.2 which is a whole lot less buggy.
    If the issue was not happening before, then the TC is not happy with the Cisco.. does the cisco have gigabit ethernet LAN ports? Did you test with another ethernet cable? Did you make sure it is connecting at gigabit.. the TC is useless and shows nothing but the Cisco might.
    I would like you to do a couple of tests.. to find where the issue is.
    Copy a file from your Mac to another computer on your own network, both connected by ethernet. See what speed you get LAN to LAN. This is to make sure the issue is only with LAN to WAN transfer.
    Place a switch .. fast ethernet is fine.. ie 100mbit between the TC and Cisco, to see if the issue is link speed.
    I have to warn you.. in the end most people who have listed the problem have just given up.. bought a new router (not apple) and bridged the TC and use it purely for wireless and backups.
    If the cisco is a router, don't even worry about it.. just bridge the TC and use it for backups only.

  • Cisco 3925 router with an ATM E3 card that never goes down!

    Hi all,
    We a Cisco 3925 router with an ATM E3 card (NM-1A-T3/E3) configured as below with 1 PVC. we see that the ATM subinterface we created for the PVC never goes down! not even when the WAN link is down! The problem with this is we are tracking the line protocol of the ATM sub interface to have VRRP failover to standby router. But because of this issue only BGP goes down whenever the WAN is down & line-protocol of the Subinterface remains up, the failover never happens & site is down. We can configure VRRP to track reachability of a BGP route as workaround but I would like an explanation or troubleshooting steps to check whats the trouble with current setup?
    Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T4.1, MAINTENANCE INTERIM SOFTWARE
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Tue 30-Aug-11 08:44 by prod_rel_team
    card type e3 1
    interface ATM1/0
     description Link to PE
     mtu 1500
     bandwidth 34010
     no ip address
     no ip proxy-arp
     logging event subif-link-status
     no atm ilmi-keepalive
     no atm enable-ilmi-trap
    end
    interface ATM1/0.101 point-to-point
     description PVC to MPLS PE
     mtu 1500
     bandwidth 2500
     ip address a.b.c.d 255.255.255.252
     no ip proxy-arp
     ip flow monitor FMforIP4in sampler ata1to100 input
     ip flow monitor FMforIP4out sampler ata1to100 output
     ip nat outside
     ip virtual-reassembly in
     no atm enable-ilmi-trap
     snmp trap link-status
     pvc 1/101
      vbr-nrt 8192 8192 1
      vc-hold-queue 2048
      oam-pvc manage
      oam retry 3 5 1
      oam ais-rdi 15 3
      encapsulation aal5snap
      protocol ip inarp
      queue-depth 5 3
      service-policy out Edge_Queueing
    end
    Thanks a lot in advance!

    Your router has some configuration on it already and it would help us give you better advice if we knew what is already in the configuration. So would you post the output of show running-config (if there is sensitive information like addresses and passwords you can mask them out.
    Changing the configuration register was a good start. I have a couple questions/observations that may help you get started. I notice what appears to be the same public IP address on Gig0/0 and on multilink. Did you get that address from your ISP? If so what kind of connection do you have to the ISP?
    In your description you tell us that Gig0/0 is connected to a small switch, which I assume is for the LAN of your network. But that also is the interface where the public address is configured. So I am confused whether this interface is for LAN or for connecting to the ISP. Can you clarify this?
    HTH
    Rick

  • Cisco 3925 and SFP modules

    I'm trying to install a MGBSX1 into the Cisco 3925 but it's doesn't seem it's detecting it for some reason.
    I've changed media type and I've tested with another SFP module (GLC-SX-MM) which works fine.
    Am I missing a command to enable this type of module on the Cisco 3925?
    Thanks

    Hi,
    Looking at the SFP compatability table for 39XX series routers.
    http://www.cisco.com/c/en/us/products/routers/3900-series-integrated-services-routers-isr/relevant-interfaces-and-modules.html#formfactor
    The MGBSX1 is NOT mentioned
    Looks like the MGBSX1 is only compatable with the Small Business switch family.
    http://www.cisco.com/c/dam/en/us/td/docs/interfaces_modules/csbna/mgb/quick_start/guide/Optical_Module_QSG_en-US.pdf
    Regards
    Alex

  • Contacts search for cisco Jabber for Windows & MAC

    Hello,
    Please assist on given below query !!
    System Deatails of CUCM & IM Presence Server
    CUCM:
    1>  System version: 9.1.1.20000-5
    2>  VMware Installation: 2 vCPU Intel(R) Xeon(R) CPU X5650 @  2.67GHz, disk 1: 80Gbytes, 4096Mbytes RAM
    3> Physical Server UCS210 M2
    4>  Already Integrated with IM & Presence
    IM & Presence:
    1>  System version: 9.1.1.20000-5
    2>  VMware Installation: 1 vCPU Intel(R) Xeon(R) CPU X5650 @  2.67GHz, disk 1: 80Gbytes, 2048Mbytes RAM
    3> Physical Server UCS210 M2
    4>  Already Integrated with CUCM
    Requirement:
    1>  User Search base for Cisco Jabber for Windows & MAC Client
    2>  Will we able to get contacts list(Jabber For windows & MAC) as like "Lotus Sametimes" for all users?
    Every reply would highly Appreciated!!

    Hi Karthik,
    Thanks for your reply!
    I have gone through the link but query is different actually, please assist on below query and provide any document links if possible.
    1>  The contacts does not appear when I perform a search
    2>  Do I required to integrate LDAP for same? If Yes Then Do I need to perform integration with CUCM Or IM & Presence? Or Only CUCM? Or only IM & Presence? (Please post a link to perform same)
    3>  Please also provide If any specific system requirement for LDAP server.
    4>  Is it possible without LDAP integration?
    It is really urgent and every post would highly appreciate..........

  • No variable audio output for Cisco CHS 435HDC set top box.

    Background:  Until the other day I had my stb connectected to a TV, using TV sound, with an HDMI cable.  The P265v2 remote volume control changed the TV volume.  No problems.
    My new TV & home theater system was recently installed.  We don't use the TV speakers.  While my first preference was to program the Verizon remote to change the volume on my Onkyo receiver, this did not appear to be an option on the remote's programming instruction page on the Verizon website.  Instead, I am directed to change a setting on the remote that makes the Verizon remote change the stb output volume vs the tv volume.  I changed the setting on the remote and ensured the stb box was set up for "variabe" audio output.
    Problem:  Using the stb variable audio settings, volume settings 1 through 30 produce the same volume.  (Volume setting 0 produces no volume, as one would hope.)  It appears the "variable" setting isn't producing a variable output as it should be on this unit.
    Thinking that maybe the receiver was complicating the sitation, I tried connecting the stb to the old TV and the new TV directly and had the same results.
    Now, while I am watching TV, I need to have the receiver remote at hand in addition to the Verizon remote.  It would be nice to have the volume be adjustable as it should be while using the Verizon remote.  I don't like the idea of using a seperate universal remote because then I would lose some of the functionality that the Verizon remote provides when watching TV, using the DVR, watching on demand, etc.
    I would like to know if this is a problem just with my unit, or if it exists with all of these units, which would hopefully be fixed with a Cisco/Verizon firmware update soon, hopefully.
    Thank you.

    soups230 wrote:
    Having same issues with hdmi and optical. Any fix to this.
    Hello,
    In order to control the volume on your home theater system, you'll need a FiOS TV Universal Remote that has the 4-buttons on the top for 'DVD', 'Aux'iliary, 'TV' and 'STB'.  The audio receiver would have to be programmed into the FIOS TV Remote, and controlled using the 'Aux'iliary button.
    Verizon's 4-Button Universal Remote Controls are available for purchase:
    a) online via www.verizon.com/fiosaccessories
    OR
    b) at a local FiOS TV store (call first to check if they have them in stock).  For a list of stores:  http://www22.verizon.com/support/residential/tv/fiostv/general+support/account+issues/questionsone/8...
    Presently, the default remotes for new set top boxes are the 2-button P-265 (newer version) remotes.
    Regarding a problem with HDMI/optical on Cisco 435 STBs, check out the following:
    Go to this webpage:  http://www22.verizon.com/Support/Residential/TV/FiOSTV/Receivers/Equipment+Issues/QuestionsOne/12839...
    Click on the link for 'Cisco CHS 435 HD DVR User Guide'.
    Open the PDF and go to page 22 for 'Connecting to a Home Theater System...'.
    Hope this helps!

  • What Service Restarts the Data Calculations for Cisco Supervisor Desktop and Wallboards

    Hello All,
    UCCX version 8.0.2.11005-20
    UCCX is running in HA mode.
    Yesterday we believe our UCCX Servers failed over due to a network outage between the Publisher and the Subscriber.
    So last night I restarted the "CCX Engine" to fail-back the servers, which worked just fine.
    Now today the database that our Wallboard uses is not showing any data. So I ran some SQL statements on both Servers' CLI and the Database db_cra is showing old data on the Subscriber and the Publisher is showing all Zeros. But after just looking at the Real-Time Reporting page on the Web GUI, that "seems" to be working but I'm not positive because I have nothing to compare the numbers to...
    When I try to run Supervisor Desktop, I can open the Program, sign-in, and then when I choose the "team" and then try clicking on a CSQ Name, Supervisor freezes and I get a "Not Responding" message. I thought it was just my PC but this is happening for 2 other people as well, on 2 completely different PCs so I can rule out that its the computer that is killing Supervisor.
    Is there another service that needs to be restarted in order to get this working? I tried restarting the service for "Cisco Desktop Recording and Statistics Service" and I was nervous about restarting anything else because we are currently open and our CallCenter is taking calls.
    Any thoughts would be much appreciated!
    Thanks in Advance,
    Matt

    Has your problem cleared up?  Did you do anything, such as a reboot or open a TAC case?
    Anthony Holloway
    Please use the star ratings to help drive great content to the top of searches.

  • Rrack mounting brackets for Cisco switch SF300-48P ?

    Does anyone know how to get rack mounting brackets for Cisco switch SF300-48P ?

    You might be able to get them through Cisco support.  Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-mount-brackets

  • RAID Configurations for Cisco servers

    Hi All,
    What is the RAID configuration for Cisco Appliance(Version 8.5) like CUCM, CUPS, CUIC, Unity etc?RAID Configuration will be done while installtion itself or we need to do it explicitly?
    Regards,
    Adithya

    Hi Geoff,
    Thanks for the reply. Just wanted to know whether if this RAID configuartion is similar to the other server RAID where we install Cisco applications.(Like OS & Application Software is RAID 1 and Database is RAID10).
    Regards,
    Adithya

  • Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

    Hi All,
    Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
    Any help would be greatly appreciated.
    Thanks in advance.
    Samir

    Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices.  RME will only use HTTPS to fetch VPN concentrator configurations.

Maybe you are looking for