BUG: RV042 (1.3.12.19-tm) not ready for Win7 RDP ?

Hello,
we used a CISCO RV042 with Firmware version: 1.3.12.19-tm (CPU: Intel IXP425-266, DRAM: 32M, Flash: 8M) with a "Gateway to Gateway" VPN Tunnel connected to a CISCO1921/K9-SEC with ZBF. The Tunnel works fine.
A connection to a WinXP (Professional) RDP works permanent. Then we had to connect to a Win7 (Professional) RDP: the connection was established, but is canceled with different error-messages by the "RDP-Server" on the "RV042 LAN". Problems with the host-cert or RDP-Server not ready was announced. (???) We started a trouble-shooting on both sides and can't find a clear statement in the log-data on CISCO or Windows Harwdare.
Then we replaced the RV042 with a RV042G V01 with Firmware version: 4.2.1.02 -
No problems with RDP to Win7 RDP anymore !
We only chnaged the hardware - VPN configuration on CISCO1921 and RV042G was not changed.
Is RV042 (1.3.12.19-tm) not ready for Win7 RDP ?
Grüße
Stefan

dondersconsulting schrieb:it works fine with Server 2008R2 RDP, which should be same as Win7.
You are using a IPSec Tunnel to an RV042 (not the Client feature!) and you can connect to an Server 2008R2 to RDP trough the tunnel ?
dondersconsulting schrieb:Are you connecting the RDP session through the VPN? If so, I'm not sure why the RV042 would have anything to do with the RDP session.
Yes, we are connecting via IPSec from a CISCO1921 to the RV042. I think that the RV042 has problems with it's own Stateful Firewall related to the local routing throug the IPSec tunnel. In this case the RDP protocol has changed on the Microsoft side from to .
dondersconsulting schrieb:If you are connecting directly through the internet using Forwarding or UPnP, then it should work fine.
Thats not our setup and is far away from any security policies on our side ...
dondersconsulting schrieb:The only thing that throws a flag for me is the certificate message. The RV042 uses an SSL cert for various things, but there is no clear way to refresh this cert when it gets corrpted. For some reason it is hidden in the VPN client setup - look for the button at the bottom that says "Generate" - use this to create a new certificate, then save the settings and reboot the router.I'm not sure that this is the issue, but it shouldn't hurt anything to reset the certificate. If you have a valid signed certificate to import, that might be even better.
The Certs you discribe are going with the "Client To Gateway" feature and we are using "Gateway To Gateway" feature.
I think the RV042 is working fine with the IPSec-Tunnel Feature "Gateway To Gateway". It works fine with WinXP Hosts connecting RDP through the tunnel - but using Win7 RDP the RDP Sessiopn breaks with all avaiable Error Messages in a random output on any Win-Client (WinXP and Win7) - we teste with 5 ! different machines ...
I looks like Firewall Bug on the RV042.

Similar Messages

Firefox beta 35 not ready for prime time.

I have spent the entire weekend trying to get the Firefox beta 35 to work. What I have found is that *all* extensions fail to work with the exception of Places Maintenance. I can not download any extension Firefox is so famous for. The error is something like "cannot install 'plugin-name' in it's current state." Enabling any extension require a FF restart, even Places Maintenance. Trying to remove an extension fails and must be done manually.
I am on Windows 7 Premium desktop Firefox, 32 bit. I "committed" myself to FF 35 last night (which meant clearing history and cache on exit because the extension "Expire History by Days" was no longer working), when I discovered that 35 was not playing nice with some sites using Flash. It was a capricious thing. Many sites worked as normal but some would not render at all. Examples:
http://www.wunderground.com/US/WI/La_Crosse.html
http://www.weather.com/weather/5day/l/Hustler+WI+54637:4:US
First time I have has a problem with a Firefox beta, but it is definitely not ready for prime time. I realize FF is attempting to get away from what we are calling "Proprietary add-ons" but FF 35 in its present state will just fill the Moz Support forums with millions of complaints (guess I am one of the first). I have at present 1 extension (the only one that works on 35), the above mentioned "Places Maintenance."
I thought you might like this report as "user input." God knows I have tried...I must have downloaded 35 at least a dozen times and then been forced back to 34.0.5. So I am back on 34.0.5
I have submitted a bug report here:
https://bugzilla.mozilla.org/show_bug.cgi?id=1108196
Let me know if anyone else is having these problems or anyone needs more information. I'd love to help fix this. I know some of you good support people have probably tried 35. Are you having the same difficulties?
Below is my (34.0.5 but the same as I had on 35 last night with the exception of "Version") trouble shooting information minus a million entries for my printer:
Application Basics
Name: Firefox
Version: 34.0.5
User Agent: Mozilla/5.0 (Windows NT 6.1; rv:34.0) Gecko/20100101 Firefox/34.0
Multiprocess Windows: 0/1
Crash Reports for the Last 3 Days
All Crash Reports
Extensions
Name: Places Maintenance
Version: 1.3
Enabled: false
ID: [email protected]
Graphics
Adapter Description: NVIDIA GeForce 9400 GT
Adapter Drivers: nvd3dum nvwgf2um,nvwgf2um
Adapter RAM: 1024
ClearType Parameters: Gamma: 2200 Pixel Structure: B ClearType Level: 50 Enhanced Contrast: 300
Device ID: 0x0641
Direct2D Enabled: true
DirectWrite Enabled: true (6.2.9200.16571)
Driver Date: 12-19-2013
Driver Version: 9.18.13.3221
GPU #2 Active: false
GPU Accelerated Windows: 1/1 Direct3D 11 (OMTC)
Subsys ID: 304619da
Vendor ID: 0x10de
WebGL Renderer: Google Inc. -- ANGLE (NVIDIA GeForce 9400 GT Direct3D9Ex vs_3_0 ps_3_0)
windowLayerManagerRemote: true
AzureCanvasBackend: direct2d
AzureContentBackend: direct2d
AzureFallbackCanvasBackend: cairo
AzureSkiaAccelerated: 0
Important Modified Preferences
accessibility.typeaheadfind.flashBar: 0
browser.cache.disk.capacity: 358400
browser.cache.disk.smart_size_cached_value: 358400
browser.cache.disk.smart_size.first_run: false
browser.cache.disk.smart_size.use_old_max: false
browser.cache.frecency_experiment: 3
browser.places.smartBookmarksVersion: 7
browser.search.suggest.enabled: false
browser.search.useDBForOrder: true
browser.sessionstore.enabled: false
browser.sessionstore.max_tabs_undo: 0
browser.sessionstore.upgradeBackup.latestBuildID: 20141126041045
browser.startup.homepage: http://www.wcwcw.com/
browser.startup.homepage_override.buildID: 20141126041045
browser.startup.homepage_override.mstone: 34.0.5
browser.tabs.loadInBackground: false
browser.urlbar.autocomplete.enabled: false
dom.indexedDB.enabled: false
dom.mozApps.used: true
dom.w3c_touch_events.expose: false
extensions.lastAppVersion: 34.0.5
font.internaluseonly.changed: false
general.autoScroll: false
gfx.direct3d.last_used_feature_level_idx: 1
keyword.URL: https://www.google.com/search?q=
media.gmp-gmpopenh264.lastUpdate: 1413301734
media.gmp-gmpopenh264.version: 1.1
media.gmp-manager.lastCheck: 1417991594
network.cookie.cookieBehavior: 2
network.cookie.prefsMigrated: true
places.database.lastMaintenance: 1418059778
places.history.expiration.transient_current_max_pages: 80511
plugin.disable_full_page_plugin_for_types: application/vnd.fdf,application/vnd.adobe.xdp+xml,application/vnd.adobe.xfdf,application/pdf
plugin.importedState: true
plugin.state.np32dsw: 1
plugin.state.npdeployjava: 0
plugin.state.npgoogleupdate: 0
plugin.state.nppdf: 2
plugin.state.npwatweb: 2
privacy.clearOnShutdown.cookies: false
privacy.clearOnShutdown.formdata: false
privacy.clearOnShutdown.offlineApps: true
privacy.clearOnShutdown.sessions: false
privacy.cpd.cache: false
privacy.cpd.cookies: false
privacy.cpd.offlineApps: true
privacy.cpd.sessions: false
privacy.popups.showBrowserMessage: false
privacy.sanitize.migrateFx3Prefs: true
privacy.sanitize.sanitizeOnShutdown: true
privacy.sanitize.timeSpan: 0
security.disable_button.openCertManager: false
security.disable_button.openDeviceManager: false
security.warn_viewing_mixed: false
storage.vacuum.last.index: 1
storage.vacuum.last.places.sqlite: 1415513129
Important Locked Preferences
JavaScript
Incremental GC: true
Accessibility
Activated: false
Prevent Accessibility: 0
Library Versions
NSPR
Expected minimum version: 4.10.7
Version in use: 4.10.7
NSS
Expected minimum version: 3.17.2 Basic ECC
Version in use: 3.17.2 Basic ECC
NSSSMIME
Expected minimum version: 3.17.2 Basic ECC
Version in use: 3.17.2 Basic ECC
NSSSSL
Expected minimum version: 3.17.2 Basic ECC
Version in use: 3.17.2 Basic ECC
NSSUTIL
Expected minimum version: 3.17.2
Version in use: 3.17.2
Experimental Features
---------------------

Just for the record I'm using Fx35b1 with lots of plug-ins and extensions with absolutely no problems now or for quite a long time.

Linux is not ready for the desktop - Mandriva devs

I just read this in the latest DistroWatch Weekly:
You wouldn't expect something like this to happen at any time, let alone on the eve of Mandriva Linux 2007 release. Last week, two Mandriva developers went on record saying that "Linux is not ready for the desktop". In a web log post entitled Why I'll never use Linux for my main desktop, Vincent Danen concluded: "This kind of thing is precisely why, for me, Linux belongs on the server. Now if those kernel-developing idiots would get their act together and give us a 2.6 kernel that was a) stable and b) supported for more than a week, then I'd really be pleased." Another Mandriva developer, Fabrice Facorat, agreed. In a post called Linux ready for Desktop? Of course not!, he had this to say: "For me when you have control over the environment and the hardware, Linux is ready: think servers, workstations, thin clients, kiosks. However when you have no control on the hardware, Linux is not ready because it somewhat lacks flexibility."
There you have it, right from the horse's mouth! From two guys who have been working for a Linux company, developing a popular desktop Linux distribution, for years! Yes, that's right, Mandriva Linux is not ready for your desktop! Don't waste your money buying it!
One really has to wonder about the future of a company which happily asks Gaël Duval to leave, yet is quite pleased to keep developers who publicly hint that they consider Linus Torvalds, Alan Cox and other kernel developers "idiots"! A perfect pre-release PR, non?
No comments... I just cannot find any words. :shock: :?

ughhhh. Mandrake have always sucked at marketing, they do themselves no favours. IMHO, they're becoming more and more irrelevant with each release. Once upon a time I might have reccomended mandrake to a newbie, but certainly not now. They've got great assets and a good base. The *potential* to become a good distro. But each release, stupid bugs make it through, and the improvements seem negligable.
Once of their better features is their huge repository of packages -- which is horrendously poorly advertised. You'll find nowhere in the GUI's or desktop a place to access their 'contrib' repo which is the equivalent of our extra, and contains a huge amount of packages. Also an important point for mandriva has been mandrakeusers.org/mandrivausers.org, which has been a huge community offering great support for newbies to mandrake, rather than directing them into the expensive mess that is known as the mandriva club. Mandriva have totally ignored this resource, and have made no attempt to support this board, upon which you'll find, I have quite a reasonable post count from back in my early days of Linux (mandriva 8.2 was first distro), and continuing on to now. It also exemplifies their (lack of) decent customer support.
The distro has had countless irritating bugs which pervaded through releases, and all sorts of utterly stupid ones that should never have made it through the testing process. They do little to help themselves with this. I've reported countless bugs, and all of them have been ignored for months. On their last release, they included the old rt2500 module, which at the time, hard locked SMP machines, and made my mandriva unbootable as it was loaded on boot. I filed a bug, marked it as high priority and it was utterly ignored for more than 6 months, so much so I had forgotten about it. Other bugs and emails have suffered a similar fate.
It's GUI tools, have become a complete mess, for example wireless, in 2006 release, was absolutely horrendous to configure, and had no support for WPA -- wpa_supplicant wasnt even on the CD's so people could configure it manually.
It's good to see they're finally ditching their old desktop theme, which they dragged on for far too long. It's always been absolutely hideous.
Their business model emphasises the 'club' far too much, making it difficult to even find a download on their site for the standard version, which has "Free" tacked all over it, as if to try and make you feel like a cheapskate. Doesnt help how they change their release cycle frequently either.
The stupidity of Mandriva just confounds me. PR like this does nothing to help them. They criticise the developers for not providing a 2.6 kernel that is stable. Maybe mandriva should look in their own backyard, and offer a distro that's remotely stable. Last time I used it, it had a horrendously old udev, hotplug, and a very slow hardware detection system. It still used bootsplash, which has been unmaintained for over two years, and included supermount, which Con Kolivas has disowned and again, has abandoned for years. They're hardly doing themselves favours patching their kernels with this out of date crap. Nor do they update them, I dont see mandriva offering updates to newer ones, which would no doubt fix many of the reported issues.
Alternatively they could do what other distros do and pitch in and help. Many of the kernel developers are also employees of other vendors, or have an important part in other distros, such as Daniel Drake and Robert Love. It'd be great for mandrake if they employed a kernel developer, because it's clear THEY are the ones who are the idiots.
I have no idea how they made it out of their bankrupcy, with the lacklustre state of their miserable distro, I think their days are numbered, unless they do something to change around their image and fix their product.
ok, im done.
James

V4.0 won't start. crashes each time. Had to go back to previous version. Version 4 is just not ready for general release, it is massively messed up. The online fixes here had no effect whatsoever. VERY DISSAPOINTED

tried automatic upgrade from within 3.6.. did not work..crashed upon re-start. tried remove program completely for a fresh install..same thing crash upon V4.0 start up....
Reinstalled 3.6.15...
4.0 is NOT READY for general release. Tried the fixes as suggested here, but they were useless and no help what-so-ever.
Very dissapointing, as I've been using Firefox as my only browser since it was introduced years ago.. this may be the end of the line....VERY DISSAPOINTED

tried automatic upgrade from within 3.6.. did not work..crashed upon re-start. tried remove program completely for a fresh install..same thing crash upon V4.0 start up....
Reinstalled 3.6.15...
4.0 is NOT READY for general release. Tried the fixes as suggested here, but they were useless and no help what-so-ever.
Very dissapointing, as I've been using Firefox as my only browser since it was introduced years ago.. this may be the end of the line....VERY DISSAPOINTED

BADI Error: Field GOITEM-ACCT is not ready for input ? HELP!

I get this error message when testing my BADI in the MIGO Transaction. The BADI is the MB_MIGO_BADI. It is from the Line_modify method. Here is the entrie message:
BAdI: Field GOITEM-ZZREG_ACCT is not ready for input. (Change is not copied over)
Message no. MIGO050
Diagnosis
The contents of field GOITEM-ZZREG_ACCT have been changed in BAdI MB_MIGO_BADI (method LINE_MODIFY). The field, however, is not ready for input, so the change cannot be copied.
In method LINE_MODIFY, only the contents of fields that are ready for input can be changed.
The field is defined correctly in the screen as an input/output field - so it does not relate to that.
HELP!!!!!

Yes - I have reviewed all of the code and I never do any modify to the screen attributes of a field - although it sure acts like it. The screen lets me put in data and it stays there up until it finishes the method line_modify. The error is when i press return after i enter the field- it completes the BADI method and then goes to the main program and does field validation and always comes back with some internal table field called "work" with a value of 0 and it should be a value of 6.
Thanks!
Scott

"This drive is not ready for use; it's door may be open ..."

Hi.
I recently updated to itunes 7, and then had an issue with a corrupt file on the i-pod (which resulted in chkdsk hanging itself at 27%, always). So I restored the i-pod and that took care of that - chkdsk now says it's fine.
However - it is also empty. My machine and i-tunes recognize it fine upon start-up; however, a short while into a full synch to get my library back on the i-pod, I invariably get the following error message:
"The drive is not ready for use; it's door may be open. Please check drive \Device\Harddisk\DR 3 and make sure that a disk is inserted and that the drive door is closed." The message comes with the options "cancel, ignore and continue", yet the latter two don't make a difference, and even if I choose cancel, itunes keeps trying until it eventually crashes.
This always happens after itunes has synchronized about 1.13 GB (out of 18.55 available).
As far as I can tell, both my system and the iPod are up to date (itunes and windows update say so, anyway). E: is unequivocally and exclusively allocated to the i-pod; changing the settings from "optimize for quick removal" to "optimize for performance" has made no discernible difference.
Any ideas would be very much appreciated.
Thanks.
DELL Inspiron 4150 Windows XP

Hullo ...
let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
Thanks.

"The drive is not ready for use; its door may be open. Please check drive \

3G IPOD problems which are driving me mad and i can see others have had the same problem but i can't find any solution written down.
Basically my IPOD either freezes after a couple of songs or it downloads about 6Gb (of 40) and the freezes with the following message:
"The drive is not ready for use; its door may be open. Please check drive \Device\Harddisk2\DR6 and make sure that a disk is inserted and that the drive door is closed"
I've tried re-setting, installing etc but no luck. Any suggestions/solutions?
Laptop - Packard Bell Notebook Windows XP

Hmmmm. I'm not sure how to explain this.
You need to change the Drive Letter for your iPod.
You should be able to connect your iPod then open Windows Explorer and right click on your iPod(which seems to be Drive E:) and change it to a different letter (like H).
If you haven't enabled disk use for your iPod it probably won't appear in Windows Explorer.
To enable disk use: connect iPod, open iTunes. Open Preferences and select the iPod tab. Choose "enable disk use."
Once you've done all that, try resyncing.

HP Officejet Pro L7590 &/or HP Slimline computer NOT ready for market

I purchased the Officejet last August and used in through December with a Dell with no problems whatsoever. When I bought an HP Slimline with Vista 64 the printer started spitting out a dozen pages with a few lines of garbage characters for each document including the Test Page, and did not completely print the documents. I spoke with three technicians who were all given remote access. We each spent about 3 hours per session. They were unable to make ANY progress in solving the problem. HP provided a VISTA 64 installation disk. It should not have done so. HP has taken no responsibility for releasing a product to market that is not ready for use but will not accept it back and will not give credit for the expensive paper weight that it has become. Moral of story: stick with Dell, don't buy anything from HP.

Thanks for visiting the HP Consumer Support Forums.
This
forum is for suggestions directly related to the forums. If you'd like
to leave feedback regarding issues not directly related to the forums,
please follow this link:
http://welcome.hp.com/country/us/en/contact_us.html
This
is a user-to-user community, and not a venue to receive directly help
or feedback from HP. If you have any further questions or concerns,
please feel free to send me a Private Message.
Thanks!
Clicking the "Kudos star" to the left is a great way to say thanks!
When your problem has been solved, accept the solution by clicking the "Accept as Solution" button to help other members in the future!
Rules of Participation

Migo: field not ready for input

hello ,
i am stuck with an issue , which is ---
I have to add two fields in migo tablecontrol with dyndr- 200, for overdelivery tolerance and under delivery tolerance.
I am able to add them with my custom fields (ZZUEBTO,ZZUNTTO). and now fields are their in table control .
But now the issue , when i am initializing values to these fields using badi MB_MIGO_BADI ,and method LINE_MODIFY,
its showing warning that --
BAdI: Field GOITEM-ZZUEBTO not ready to accept input (Change will not be adopted)
Message no. MIGO050
Diagnosis
The contents of field GOITEM-ZZUEBTO have been changed in BAdI MB_MIGO_BADI (method LINE_MODIFY). The field, however, is not ready for input, so the change cannot be copied.
In method LINE_MODIFY, only the contents of fields that are ready for input can be changed.
if any one , please revert me back .
Thanx,
Jeetendra Chauhan
Edited by: jeet.chauhan on Jun 2, 2011 7:58 AM

Hi
If I understand you, you are modifing the standard dynpro SAPLMIGO 0200 (ie: the table control TV_GOITEM). I suggest you to avoid it and mantain these fields in a new tab with this BADI and methods PBO_DETAIL and PAI_DETAIL.
Regards
Eduardo

Field property indicator is not ready for input in sap

HI All,
i am trying to post transaction in GJT1.
i am getting below error "field property indicator is not ready for input"
i tried taking different asset,
now it is showing below error msg. please assist me on both the issues.
"system status CRTD is active"

I got the answer.
using GJVV i was able to resolve my issue.

Where is the "not ready for input" field stored in SAP?

Hi,
In the tcode CT04, the 'Additional Data' tab has a field called 'not ready for input'. I want to find this value in a table. I thought it was in CABN-ATINP but this does not seem to be populated all the time.
e.g.
1. characteristic ABCDE has the value checked in CT04 but there is no entry in CABN-ATINP
2. characteristic ZYXWV has the value checked in CT04 and there is an entry in CABN-ATINP
Does anyone know:
a) why?
b) how to find the value for point 1 above?
Thanks,
Kroc.

obviously, that is wrong.
It is true that the ATINP value for batches which have a reference field in CT04 does not ever change but having a reference field does not necessarily mean that it should be display mode.
Anyone know why the reference field stops the ATINP field update?
And how does the program know that it should be 'not ready for input' when the ATINP flag is not changed?
Thanks.

Drive not ready for use

when i go to update my ipod, i get this error: "the drive is not ready for use; it's door may be open. Please check drive\device\harddisk2\DR4 and make sure that a disk is inserted and that the driver door is closed." then it proceedes to freeze up itunes and then the computer. So when i get this, i have to format my ipod so that i will be able to put music on it again. then after 3 or 4 updates the same thing happens. but never right after i format it. anyone have this happen before or know why this would happen? it is an older ipod, with the click wheel. and it does have the most recent update.
Windows XP

Try changing the drive letter for your iPod.
If you don't know how to do it, I'll look around a bit and find an article to help
~iBook G4 1.07GHz (Kaiya), with extra 256MB RAM ~and a red Apple logo~(Mac OS X 10.3.9)~ LaCie 160GB external hard drive~ ~3G 15GB iPod (Nakai)~ ~GiveStarsto users who earn them.~

Drive not ready for use, door may be open

iTunes transfers about 800mb of content before error message appears:
The drive is not ready for use; its door may be open. Please check drive\...
I have restored, formatted, tried different PC's always get same result. Visited genius bar and they declared that my iPod was healthy but refused to move enough content to the iPod to reproduce the problem. iPod is a little under 2 yrs old.
My confidence and respect regarding Apple and it's products is now greatly in question. I spent $400 duchats on this thing and I am starting to feel like an unappreciated client.
Thanks for any help...

Hullo ...
let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
Thanks.

Interactive form within WebDynpro not ready for input

Hi,
After building a simple interactive form with the form builder, I want to fill in the fields in the adobe form. The form is included in a ABAP web dynpro application as Interactive form and the enabled property is checked. But the form fields are still read only and not ready for input.
The interactive form uses ZCI layout and an ABAP dictionary based interface. The menu item include scripting was hit and I can not fill in the fields. Instead I only see read only fields. When previewing the form in the forms designer, the fields are open.
Please assist.
Regards
Ravikumar

hi Ravikumar,
The following code fragment shows how this input readiness can be set up:
method WDDOMODIFYVIEW.
data: LR_INTERACTIVE_FORM type ref to CL_WD_INTERACTIVE_FORM,
LR_METHOD_HANDLER type ref to IF_WD_IACTIVE_FORM_METHOD_HNDL.
check first_time = abap_true.
LR_INTERACTIVE_FORM ?= VIEW->GET_ELEMENT(u2018INTERACTIVE_FORM_1u2019).
LR_METHOD_HANDLER ?= LR_INTERACTIVE_FORM->_METHOD_HANDLER.
LR_METHOD_HANDLER->SET_LEGACY_EDITING_ENABLED( abap_true ).
endmethod.
Hope this helps.

Input ready query - not ready for input

I have created the following in IP:
1. A multiprovider based on an actuals cube (Standard infocube) and a plan cube (realtime - data can be planned not loaded).
2. An Aggregation level on the multiprovider - containing infoobjects: 0version, employee, WBS element, infoprovider, fiscal year, fiscal year variant, 0currency and 0amount.
3. A filter on the following infoobjects: employee (=123456), wbs element(XX.XX.XXX.X), version (variable - mandatory; ready for input), fiscal year(2008) and fiscal year variant(XX).
4. A planning function to copy from version 0 (actual) to version 866 (random Value - Master data exists).
I have created a query on the multiprovider and set the query properties correctly. I have also created two restricted key figures as follows:
1. Actual (Restricted by infoprovider = actual; version = 0; fy = 2007; fyvar = XX)
2. Plan (Restricted by infoprovider = plan ; version = input-ready variable; fy = 2008; fyvar = XX)
I have used all the infoobjects in the agg. level in the query. I am using the same version number (866) on the query selection screen as defined in the filter.
When I run the query, I can see only the actuals line. The plan keyfigure is not ready for input (although keyfigure properties are set to "Data can be changed using user entries or planning functions).
What am I doing wrong which is preventing the plan keyfigure from opening up for planning?
I have also tried to create an agg. level on the plan infocube with similar settings as above. When I run the query, I get a no data found result - which I think is right because there is no data in the planning cube.
PS: When I use the wizard in the planning modeler the keyfigure (0amount) can be changed.

Hi Avya,
Use a filter on the 0currency, for a particular currency type. (if problem is: currency type keyfigures are not input ready)
This will mak it input ready.
**Reward Points for useful answers**
Regards,
Naveenan

BUG: RV042 (1.3.12.19-tm) not ready for Win7 RDP ?

Similar Messages

Maybe you are looking for