Bug with Reverb/Full Reverb Effects

I just got AA3 a few weeks ago, and have immediately noticed a few problems, the most serious being an issue that occurs when running the "Reverb" or "Full Reverb" effects.
Specs: AA3 plus 3.01 patch
CPU: Intel Centrino 1.6 GHz
RAM: 1 GB
Windows XP Pro SP3
Problem: When I am running multiple effects in the multi-track view and one of them is either "Reverb" or "Full Reverb," then the all effects execute their functions approx. 25 seconds earlier than it is supposed to.
Ex: I am currently mastering a .wav file, approximately 3 minutes long in the mutli-track view. In the effects rack I am running "Multiband Compression," "Tube-modeled Compression" and "Full Reverb." When I start playback on the file, the Multiband Compression interface display reflects what's going on in the file 25 seconds later in the track. IE 25 seconds before the track finishes, the compressor stops compressing, and the spectral display within the interface drops to -80 dB (because it thinks the song is over and is not recieving any signal to process).
Furthermore, this seems to affect automation as well (but only for effects---as far as I can tell it does not effect volume or pan automation). When I automate Full Reverb to run from say WET=0% at minute 1:00 to WET=100% at minute 2:00, I can both hear the reverb begin to engage and watch the WET slider in the Full Reverb interface begin moving at approximately minute 0:35 instead of minute 1:00. I have found this glitch to happen only whenever I am using the "Reverb" or "Full Reverb" effect. It seems to affect all tracks, regardless of which track the Reverb effect is applied to--IE If I am using Full Reverb on Track 2, Track 8 effects still execute too early.
This is particularly troubling when it comes to compressors, because it implies that it is performing compression calculated for time=1:00 at time=0:35 instead. So, if the compressor is supposed to take off 3 dB at t=1:00, it is actually taking it off at t=0:35.
What's going on here? Has anyone else experience or noticed this problem? Any advice would be greatly appreciated!

My advice is to not use Reverb or Full Reverb in any Multi Track session. In fact, there is a warning box that comes up when you put Reverb or Full Reverb in an FX rack in Multi Track. The warning box tells you that these effects are CPU-intensive and not at all appropriate for use in Multi Track.
So, you can either switch to Studio Reverb (and that reverb was put in specifically because it is less CPU-intensive than the others) or get one of the hundreds of reverb plug-ins out there (and many of them are free). There used to be a good list of free plug-ins on this forum. I don't know if it is still there, but I do know that there is a list at http://www.audiomastersforum.net that recommends many good freeware reverb plug-ins.

Similar Messages

Echo and reverb effects disabled?

I created a project and recorded tracks with echo and reverb effects, but now when I open the project the echo and reverb effects are both disabled; I can't enable them or change their values, and the effects aren't present during playback or after export. Any idea what might be the reason/resolution for this? Thanks for your help.

It's not so weird if you understand how it works: These echo and reverb effects are "global" effects for your song - all tracks are sent through the same effect, and with the echo and reverb sliders you only determine the mix of "wet" and "dry". That saves a lot of processing power.
Of course you can apply additional different reverbs to each single track, but aside from computing resources it will cost you one of your effects slots.

[svn:fx-trunk] 9287: Fixes bug with shader-transition effects ( AnimateTransitionShader, Wipe, and CrossFade) when acting on targets that either have filters or are inside a hierarchy with filters .

Revision: 9287
Author:   [email protected]
Date:     2009-08-13 15:53:43 -0700 (Thu, 13 Aug 2009)
Log Message:
Fixes bug with shader-transition effects (AnimateTransitionShader, Wipe, and CrossFade) when acting on targets that either have filters or are inside a hierarchy with filters. Fix was to capture the bitmap snapshot of the target without any of its own filters applied and to then use the ShaderFilter in conjunction with the target's filters during the animation.
QE notes: Probably need more tests in this area, now that we handle it
Doc notes: none
Bugs: sdk-20250
Reviewer: Jason
Tests run: Checkintests, Mustella (spark/effects/[AnimateTransitionShader|Wipe|CrossFade])
Is noteworthy for integration: No
Ticket Links:
    http://bugs.adobe.com/jira/browse/sdk-20250
Modified Paths:
    flex/sdk/trunk/frameworks/projects/spark/src/spark/effects/AnimateTransitionShader.as
    flex/sdk/trunk/frameworks/projects/spark/src/spark/effects/supportClasses/AnimateTransiti onShaderInstance.as

Lots to be excited about. BUT...Just updated to 8.1 on one of my computers to test it out...
Sadly, the following issue is NOT fixed for me. Is it with new projects only? I haven't started a new project on 8.1 I've only opened an old project but the issue that I'm referring to which involves also a delay/freeze of anywhere from a few seconds to a MINUTE while the render bar goes from yellow to red and then back to yellow is still there. Boo.
On the list above...
Switching between sequences can turn the render bar red.
This issue is incredibly easy to replicate. I really do hope it gets fixed. Here are the steps:
1) Create two sequences with multiple short clips (the more clips the better)
2) Make sure GPU acceleration is enabled.
3) Add warp stabilizer to the clips in both sequences. Again, the more clips the longer the delay/freeze will be as the render bar goes from YELLOW to RED and then eventually back to YELLOW again.
4) Hit SAVE.
5) Now, toggle between sequences. You'll hit a short delay with a few clips stabilized and a LONG delay with lots stabilized. In my case this delay is around a full minute. The render bar will go from YELLOW to RED and then back to yellow...eventually.
6) Toggle back to the original sequence and the delay occurs again.
7) Once you've toggled between sequences and have gone through this delay, that's it, there is no longer a delay...UNTIL...(and here's the big kicker)...until the project is SAVED again. After that the issue returns when you toggle between sequences. Both saving manually and AUTOSAVING cause this issue. No way around it except not editing with GPU acceleration.
Not sure what the issue is...caching issue when saving maybe? Either way, it stinks and it's still there in 8.1. Big bummer.
Again, lots to be excited about with this release but I really was hopefully this specific issue was resolved.
Sigh.

IE7 Padding Bug with Spry Effects

I'm having a recurring issue with using the Spry Blind effect
in IE7 where, when upon trigerring the Blind, the width of the
element being expanded/contracted is expanding out to the right
over it's edges.
For example.
A div with a width of 800px and a padding of 20px;
When a Blind is triggerred on this element, the width of the
element would expand to 840px, the padding on the left side remains
fine, but the text now goes all the way to the right edge of the
newly widened element.
This has been extremely frustrating and doesn't occur in
Firefox.
I'm hoping this is a common problem. My implementation of the
script is fairly straightforward so I don't know if there is
anything else but a bug with the effect.

Here is a somewhat messy version of the page I am working
with.
http://derekprospero.com/michael/example.html
If you click the green down arrow at the bottom of the top
right pane you will see the error.
The table expands out past the borders of the div. The
padding-left and padding-right on this div is 20px each, and it
expands out to 40px past the border of the div, so I am assuming
there is some correlation.
It also happens on the bottom one, though it is not as
evidence, since the text goes behind the background, isntead of
over it.

My client with autism needs to be able to speak/sing into a microphone and simultaneously hear his voice through a headset, preferably with reverb set on high. Is it possible to do this with the iPad and OS7? If so, what setup do I need?

My client with autism needs to be able to speak/sing into a microphone and simultaneously hear his voice through a headset, preferably with reverb set on high. Is it possible to do this with the iPad and OS7? If so, what setup do I need? I have a SM58 type mic and-over-the ear headphones.

This implies that ODP.NET does NOT need to be installed on a client. However, I cannot find OraOPs9.dll on a machine with Client Release 9.2 installed. Should OraOps?.dll automatically come with a Client installation of 9.2 or higher?
ODP.NET needs to be installed on the client. OraOps9.dll is part of ODP.NET, not the Oracle Client.
Also, if an application is built with the 10g ODP.NET, can it be run from a machine with OraOps9.dll?
If an application is built with 10g ODP.NET, it can be run with 9.2 ODP.NET as long as you do not use any 10g APIs. The new features in 10g ODP.NET are included in the doc and the ODP.NET FAQ for your reference.

When trying to edit a photo, it disappears (black screen) or screen is full of lines. Is this a bug with the latest software update?

After updating with the latest software, when trying to edit a photo, it disappears (black screen) or screen is full of lines. If I blindly crop or edit the photo, when I exit edit mode, those changes have been made, but obviously this is unacceptable. Is this a bug with the latest software update?

There are several possible causes for the Black Screen issue
1. Permissions in the Library: Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Include the option to check and repair permissions.
2. Minor Database corruption: Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild.
3. A Damaged Photo: Select one of the affected photos in the iPhoto Window and right click on it. From the resulting menu select 'Show File (or 'Show Original File' if that's available). (On iPhoto 11 this option is under the File -> Reveal in Finder.) Will the file open in Preview? If not then the file is damaged. Time to restore from your back up.
4. A corrupted iPhoto Cache: Trash the com.apple.iPhoto folder from HD/Users/Your Name/ Library/ Caches...
5. A corrupted preference file: Trash the com.apple.iPhoto.plist file from the HD/Users/ Your Name / library / preferences folder. (Remember you'll need to reset your User options afterwards. These include minor settings like the window colour and so on. Note: If you've moved your library you'll need to point iPhoto at it again.)
If none of these help: As a Test:
Hold down the option (or alt) key key and launch iPhoto. From the resulting menu select 'Create Library'
Import a few pics into this new, blank library. Is the Problem repeated there?

Hum Remover turns into reverb effect

I noticed that on all the clips I have turned the Hum Remover audio analysis feature on, days later, the sound of those clips has become like a reverb effect, like a medium room effect. It's very noticeable. Turning it off fixes the issue. I'm using Adobe Audition for noise removal now.
This feature, Hum Removal, worked fine when I first turned it on. But days later, after restarting FCP X, restarting system, etc., it now sounds like a reverb effect and very strange.
Weird.

You are welcome, Al.
I don't know. 44100Hz worked well.
Below is part of the email i received from Audacity. As you can see, they say "may be expecting" which surprised me a little; one would think that they would know. Still, noise removal is a small part of Audacity. I was grateful that they wrote to me. Very kind.
For your interest, I am printing part of their response to me when I told them of my difficulties.
I suppose that when I have a moment, I could check using a 48100 rate.
If you have additional comments after reading the exceprt below, I would be interested.
Best,
Allosaurus.
"Assuming "FCE" is Final Cut Express, it may be expecting a standard
44100 Hz, 16-bit AIFF file. Therefore make sure that is what you are
exporting from Audacity.
"Set 44100 Hz for exports by setting the project rate bottom left of the
Audacity window to 44100 Hz.
"The specific option to export AIFF signed 16-bit PCM will be in the File
Formats preferences in Audacity 1.2.6, or in Audacity Beta, choose it in
the "Save as type" list in the "Export File" window when you export."

How to do a reverb effect on vocal recordings ?

Hi all experts,
Sorry I am only a beginner, what I did was TRACK > NEW BASIC TRACK. I test & record some vocal. But my voice is horrible.
What are the steps to do a reverb effect on the recorded voice ?
Thanks

RyanManUtd wrote:
Any video demo to show what those are ?
i wouldn't be surprised if there are some on YoutTube, however most of the effects are pretty standard, web searches on "EQ" or "audio compressors" will turn up more info then you could read in a lietime.
Just to be sure before I slide it.
don't worry about understanding things before you try them:
http://www.bulletsandbones.com/GB/GBFAQ.html#nondestructive
(Let the page FULLY load. The link to your answer is at the top of your screen)
May I ask, if I slide it to say 30, the 30 will apply to the whole track ?
yes
What if certain section I want it 20 & certain section I want it 30 ?
open GB's help menu and search for "curve"

PLEASE HELP!! problems with reverb

So, I am using garage band to record some guitar and I want to add the AU Matrix Reverb. It seems that when I have multiple tracks with reverb I get this really loud and annoying crackling sound that rises and fades along with the tracks. What is this and how do I get rid of it?
Thanks for reading.
Conor

I never had this happen but try locking the tracks that your aren't working on and see if the crackling persist.

RH10 and Windows 8 Bug with DHTML

I reported the following bug today:
Concise problem statement:
All DHTML effects in WebHelp—with the sole exception of drop-down and expanding hotspots—fail to execute on CLEAN Windows 8 systems (upgraded Windows 8 systems from Windows 7 do not seem to be affected), regardless of default browser.
Steps to reproduce bug:
Set up any DHTML effect other than drop-down or expanding.
Save topic and click “View Selected Item”.
The following script error is thrown: “Unable to get property ‘alpha’ of undefined or null reference” — the error points to the ehlpdhtm.js file (in my case, line 4233, char 2).
Results: No DHTML in the WebHelp output execute, with the exception of drop-down and expanding text.
Expected results: DHTML displays as developed (and yes, "Update DHTML effects in topics" was run). It is important to note that all these effects display as expected when run from a Windows 7 machine.
I noticed this after being forced to format and reinstall my system drive, on which I'd previously done an in-place upgrade to Windows 8. There was no issue unitl I'd done a clean install of the OS, implying that something carried over from the Windows 7 setup to prevent the error.
I've tested this against IE10, Firefox, and Chrome with the same results: DHTML effects (such as Fly-in) don't work and, worse, whatever the effect is attached to does not display.
If anyone else is having this issue, it would be good to report it. If anyone has a possible fix or workaround, I'll be glad to be a test monkey.
Thanks!

I'm having the exact same problem with Robohelp 9 on Windows 7. My error message says: The value of the property "TextPopupInit is null or undefined, not a Function object"
I click Yes to the question "Do you want to continue running scripts on this page" and the page previews fine. I open the page in a web browser, and it also works fine.
Any help greatly appreciated.
Lea

[svn:fx-trunk] 10898: Fix for a bug: After playing a hide effect, a window wouldn't be visible again.

Revision: 10898
Author:   [email protected]
Date:     2009-10-06 13:54:04 -0700 (Tue, 06 Oct 2009)
Log Message:
Fix for a bug: After playing a hide effect, a window wouldn't be visible again.
The issue here is that all effects that occur because of HIDE end up calling setVisible() (see EffectManager.effectEndHandler). Window/WindowedApplication was basically left with two concepts of setVisible...the displayObject one and the native application one, and they were out of synch. So setting visible=true on the window wasn?\226?\128?\153t calling setVisible(true) which controls the display object visibility. Now instead of doing our work in the visible setter, we override setVisible() and do it in there.
QE notes: -
Doc notes: -
Bugs: SDK-23263
Reviewer: Darrell
Tests run: checkintests, Rob ran mustella window/windowedapplication
Is noteworthy for integration: No
Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-23263
Modified Paths:
    flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/Window.as
    flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/WindowedApplication.as
    flex/sdk/trunk/frameworks/projects/airframework/src/spark/components/Window.as
    flex/sdk/trunk/frameworks/projects/airframework/src/spark/components/WindowedApplication. as

I run Suse 9.1 Linux, and Suse has a package called lmsensors which by default on my machine gives readings like this:
Code: [Select]
temp1: +27°C (high = +0°C, hyst = +22°C) sensor = thermistor
temp2: +41.0°C (high = +80°C, hyst = +75°C) sensor = PII/Celeron diode
Now that 41C is pretty high for an idle AMD643000+ running at 1000Mhz, 1.08V. Too high, I would say. temp 1 in this case is the SYS temp, temp2 is the CPU temp.
Now, using lmsensors I can duplicate your little trick and tell it that temp 2 is in fact a 3904 transistor. Having done this can I get readings like this:
Code: [Select]
temp1: +27°C (high = +0°C, hyst = +22°C) sensor = thermistor
temp2: +16.0°C (high = +80°C, hyst = +75°C) sensor = 3904 transistor
Problem is, I'm not sure that the sensor is actually a 3904 transistor! The number's lower, but I was pretty sure that the sensor in the AMD64 is in fact a diode. Also, surely the CPU temp can't actually be that much lower than the SYS temp.
So, I think your fix succeeds in giving lower temps and that's great in that it will tell your system software that the CPU is not overheating, but I don't think it's the solution to high temp reporting. Anyway, as you say, its a solution for people who can't run with system shutdowns due to bogus high temps.
I've been looking at these temp issues with the MSI K8T, and I was thinking the problem was simply a miscalibration. The Winbond sensor chip on my board (maybe the K8N is the same, maybe not) has a sensor temp offset that gets added to the temp coming from the sensor. On the K8T this number is +54C. Funny number I know, but I've "fixed" the problem while I wait for a real bios fix on the K8T by simply reducing this offset to give me a CPU temp that matches SYS temp when idle. This enables cool'n'quiet fan control to work properly on my system, which is my main practical concern.

Drop shadow failing to blur with high document raster effects settings DPI

I have a 1024px square artboard (in Illustrator CS6 16.1.0 running on Mountain Lion 10.8.1) with some fairly simply artwork that has a drop shadow effect applied, shown here at 33% with the Document Raster Effects Settings (DRES) resolution set to 150 DPI:
If I change the DRES resolution to 300 DPI, the blur on the drop shadow disappears entirely:
If I leave the DRES resolution at 300 DPI, but resize the image to make it a little smaller, the blur on the drop shadow comes back:
I’ve wasted several hours already trying to get the desired blurry drop-shadow on the full sized image with the DRES resolution at 300 DPI, to no avail. Does anyone have any idea as to what is going on here, and what I can do to solve this problem?
Many thanks in advance.

The Gaussian Blur was rewritten for CS6 and should probably be similar in CC. Your screen shots did not get properly attached. Can you try again to attach them using the Camera icon in the reply window tool bar?

I have down loaded a track which was initially missing 1min 30 seconds. iTunes enabled my to reload the rack which is complete on the PC. However, syncing with my Ipad2 does not seem to replace the incomplete version with the full version. Thanks S

I have down loaded a track which was initially missing 1min 30 seconds. iTunes enabled me to reload the rack which is now complete on the PC. However, syncing with my Ipad2 does not seem to replace the incomplete version with the full version. Can anyone out there help?
Thanks S

Thanks for the response. Unfortunately, I've un-checked the track and re-synced the Ipad as suggested, but then re-checking and re-syncing han no effect. The track is still missing the final minute and a half or so. I've tried it twice, but the effect is the same.
Any other ideas? Would un-checking the entire music collection and staring again work, or is that a road to disaster?

Terrible bug with Rescue & Recovery 4.5

Hello all,
Just a notice to all users, I had a terrible bug with Lenovo Rescue & Recovery. Everything went well, until the restore: I have one SSD for system and one micro sata for data. The system drive had two partitions (created by Lenovo at the origin, a system (C) partition and a Lenovo recovery partition). When I tried to restore a previous version of the system drive that I backuped with Lenovo R&R, it restored the system on C: and restored the recovery partition... on D:, erasing all my data! In addition, the MBR was missing on the system. And cherry on the cake, I could not use the backup a second time when I tried, because R&R did not find the backup again.
I was particularly disappointed because as the backup went so smoothly, I did not do a data backup before restore, my previous backup being three days old, so I lost three days of work.
I had previous bad experience with Windows backup & restore, windows software could not find the restore, but at least it did not erase data.
Thierry

I agree with the TERRIBLE bug comment.
It amounts to:
(1) restore Q partition
(2) C drive.
I will repeat my other posts. I ordered pc, with 320 GB and 160 Gb Hdd. From factory, C went to 320MB. Factory install goes to 1st HDD it finds, in my case 320 GB.
So you have discovered a new, how does it work?
1 HDD (c), 1 sata (for data). It used factory recovery items, and waxed the sata( and made it bootable). Then got smarter, and restored C to HDD, unbootable.
Did someone not test this? Dont expect a new version of RNR. not supported on win 8. Acronis, $$ well spent.
Dumb.
Next time, unplug the loved sata before a FULL HDD restore. (not a c drive restore). Sad. unplug loved!
==
Did not find backup 2nd time around. Discussed in other posts from myself. What is your windows platform RNR backup location set to? If local, change it to USB or where ever you think they are at.

[svn:fx-i11] 5537: Fix for bug with FxRotate3D that Thermo ran into with our i11 build.

Revision: 5537
Author: [email protected]
Date: 2009-03-24 20:16:43 -0700 (Tue, 24 Mar 2009)
Log Message:
Fix for bug with FxRotate3D that Thermo ran into with our i11 build. The problem was that we were sometimes setting offsets values to NaN due to bad initialization, and that we were also incorrectly calculating the transform center when offsets had not yet been initialized on the target.
QE Notes: None
Doc Notes: None
Bugs: SDK-20209
Reviewer: Ely
tests: checkintests, mustella mx/effects
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-20209
Modified Paths:
flex/sdk/branches/i11/frameworks/projects/flex4/src/mx/effects/FxAnimate3D.as
flex/sdk/branches/i11/frameworks/projects/framework/src/mx/core/AdvancedLayoutFeatures.as

We experience it as soon as we enable iCloud. Then an apple certificate is automatically added to the keychain and used for every https-access. Deleting the certificate com.apple.idms.appleid.prd... will do as a workaround but the certificate continues to be added to the keyChain from time to time or if you start over deactivating iCloud and then activate back.
Is this still a bug in Safari? Rosario

Bug with Reverb/Full Reverb Effects

Similar Messages

Maybe you are looking for