Build Problems, MSI GTX560ti and P67A-C45 with i5

All went together and POSTed fine, my problems are with the video card. After installing Windows 7 I tried to install the video card driver but got the message "no compatible hardware detected". In device manager the card is not recognised as a GTX560, it just says "Standard VGA Adapter". The fans on the card were spinning, but the display looked like 800x600 or something. Assuming the card was faulty, I swapped in my old GTX 260 (which was working this morning, running on the same PSU) but then the pc wouldnt power up at all, when I press the switch the fans spin for a fraction of a second and it powers down again. So, in desperation, I dug out an even older 9600GT, put that in, and it works, its recognised by the OS and the driver installed automatically. Now, the 9600GT requires no additional power other than what it gets from its slot, which suggests that my PSU either isnt coping with the new setup in some way, even though it was running that same GTX260 this morning, or that its faulty in some way. The PSU btw is a Zalman ZM600-HP, which does appear on the list of supported PSUs for the GTX560, even though it is a few years old now.
Do I need a new PSU? Thoughts?

Download and install drivers for your video card from:
http://www.nvidia.com/Download/index.aspx?lang=en-us

Similar Messages

MSI P67A-C45 with 4x4Gb Corsair Vengeance = random freezes in bios

Ok here is the problem i hope you guys can help me with. I recently bought the following rig:
- MSI P67A-C45 Motherboard
- 4x4Gb Corsair Vengeance memory.
- MSI N560GTX-Ti Twin Frozr II/OC
- Core i7 2600K
I am having the following issues:
Whenever i put in all the memory, the PC won't boot, it hangs even in the BIOS (at random pages). Everything seems to run fine (except for a minor detail which i will mention later) with 12 Gb installed (3 dimms that is). I have tried changing the voltage to 1.65v but this doesn't change anything. With 12 Gb (or even only 4Gb) installed there is only one weird thing happening:
Whenever the pc wakes from hibernation i get the following error:
“Your system's firmware did not preserve the system memory map across the hibernation transition. If you proceed with resume, your system could behave in an unexpected manner after resume completes. It is recommended that you save all your data and reboot after system resume finishes. Kindly check for a firmware update with your system vender as it may fix this problem."
Then after clicking resume it says i can't resume from the saved state and that it will be discarded (effectively doing a clean boot of the OS).
Can these two problems be related, and if so, is it a hardware problem or some BIOS settings i can try?
Any help would be greatly appreciated.

Quote from: Bernhard on 05-May-11, 13:51:46
1. Have you tested your mem sticks individually with memtest ? There is always a chance of a defective module.
2. Test the mem at 1333. Insert only 2, set it to 1333 manually in the BIOS, save and switch off. Add all modules and see if it boots.
3. You may also want to reseat your CPU, whilst it's out, check the CPU contact pads for indentations and see if there are any pins on the socket that are bent.
1. I have tested with 1 mem stick, then with 2, then 3 and then 4 (memtest from bios seems to be the only thing not crashing with 4 mem sticks). So i have not tested everything individually, but in my opinion this should be thorough enough.
2. I have done this exact thing but then with 3 mem sticks, only adding the last one when switched off, then turning it back on again. I will try with the two so in dual channel, this might make a bit of a difference.
3. I have reseated the CPU once, it is not a fun thing with the Big Shuriken cooler i have , i'll try this as a last resort.

MSI GTX560ti is it compatible with Asus p8z68-v?

Hi
I tried to write in English.
I have a
graphics card MSI GTX560ti
Mothercard Asus P8 Z68-V
Processor i7 2600k
Power 650W
=>no detected by Windows 7 64 bits
=>nothing appears in the Control Panel
=>no notification
=>Drivers installation impossible,
=>Lucid virtu the same thing
Do you know how make ?
How make to use this graphic card with my DVI monitor ?
Merci and sorry for my english

Your problem is most likely with ASUS, if both Gainward & MSI 560 Ti won't work then it's probably not the VGA cards, it's bad ASUS BIOS or problem of some kind with your MB. We can't help you here with it. You should still test those 2 560 Ti's in another PC.

Please help! Major problems (performance and lock-ups) with brand new W520 with Intel 520 SSD

My company primarily uses HP machines but I've been a long time IBM (now Lenovo) fan so I recently had IT purchase me a new Lenovo W520 (product ID 42763LU).
Once the machine arrived I had them do the following:
Remove the 500GB HDD and replace it with an Intel 520 series 240GB SSD
Remove the optical drive and install the 500GB hard drive that came with the machine in the optical bay (with the bay adapter of course)
Format both drives and put a preconfigured windows 7 64-bit image on the SSD
A general summary of the system is the following:
Intel i7-2860QM CPU
8GB RAM
NVIDIA Quadro 1000M
Intel 520 240GB SSD (primary HDD) [SSDSC2CW240A3]
Hitachi 500GB HDD (optical bay) [HTS727550A9E365]
Intel Advanced-N 6205 network adapter
TouchChip Fingerprint Scanner
The machine was a few days delayed getting to me due to "hard drive driver issues" (that's what I was told). When I received the machine I immediately noticed that it was much slower than I expected (I have a custom built i5 HTPC at home running windows 7 on a Crucial SATA III SSD that I was comparing it to) and I was experiencing frequent hangs (ranging from 30 seconds to multiple minutes), super long boot times, general “slowness” at times, and occasional lock-ups. Since our "baseline" laptop here at work is the "equivalent" HP workstation my IT guys have been less than helpful in helping me to solve this issue. Being reasonably computer savvy I decided to try to try to fix the issue myself. I performed the following “troubleshooting” steps:
1. One of the first issues (errors) I noticed in the event viewer was errors related to the optical drive. Clearly the image they installed on the machine was not from a machine with the same hardware configuration. So, I decided to just wipe the machine and perform a fresh install of windows 7 from the disks (well, USB). After spending multiple days installing windows, performing updates, making sure all the drivers were current, and installing only the critical software I need, I was disappointed to realize that although I fixed the optical drive errors the machine was still slow, was hanging, and locking up regularly.
2. Removed the cover on the machine and removed/reinstalled the drive to verify it was secure.Everything looked good.
3. Verified the latest firmware is installed on all my Intel hardware. Everything seemed up to date.
4. I performed a number of troubleshooting steps like booting the machine with/without the battery, with/without the HDD in the optical bay, installed/removed from the docking station, etc. and none of these things helped (also a note – occasionally when running on the battery I was hearing a strange “buzz” or “static” sound coming from the area around the SSD).
5. Next I did some internet research and learned quite a few things. First, it sounds like others have had similar problems with this machine and/or SSD combo and there were quite a few options suggested to “fix” these issues. The general consensus for troubleshooting steps were:
5.1. Download and install the latest Intel chipset drivers and AHCI controller drivers (overwriting whatever windows installs during updates).This didn’t fix anything.
5.2. Turn off PCI express link state power management in the power manager. This didn’t fix anything.
5.3. Disable superfetch, prefetch, indexing, defragmentation, page file, system restore, and hibernate. A few of these were already disabled by windows so in those cases I just verified they were disabled in the services and application editor. These things may have slightly increased performance but did not fix the major hang/lockup issues I was having.
5.4. I followed online steps to edit the registry to disable the PCI link power management by adding ports, adding the required variables, and setting them all to 0. This did seem to have fixed the hangs and/or lock-ups but the machine is still much slower than I would expect (boot times are still pretty slow and it does “stutter” when I’m doing more than one thing at a time. Also a note here – I have the Intel SSD toolbox installed and I noticed that it was giving me a warning for DIPM not being optimized. I made the mistake of clicking “Tune!” and then started having the hang/lock-up issues again. I went back into the registry and sure enough the PCI link power management variables for ports 0 and 1 were set back to 1. I set them back to 0 and the hangs have gone away. I will not be “tuning” the DIPM through the Intel SSD toolbox again…
6. I also fixed a couple of other minor errors I was seeing in the event viewer by disabling benign services and/or making slight timeout modifications (I researched each issue on the internet to verify they were benign before I implemented any changes). These fixes didn't seem to do anything other than make some of the errors/warnings go away. So, the list of errors/warnings has become much smaller but I’m still getting the following (maybe an issue, maybe not?):
Event ID 37 for every processor saying that they are in a reduced performance state for xx seconds since the last report
Event ID 10002 - WLAN Extensibility Module has stopped
Event ID 4001 - WLAN AutoConfig service has successfully stopped
Event ID 27 – Intel® 82579LM Gigabit Network Connection link is disconnected
I suspect the WLAN errors have something to do with windows fighting with the Lenovo access connection tools?
7. Since the machine still seemed slow I downloaded the program AS SSD and checked the performance of the SSD. When I compared my performance numbers to the benchmark numbers I found onlineI was very surprised to discover that I’m getting about 50% of the performance that I should (values below are read/write).
Seq: 262.11 / 188.32 (s/b 504.58 / 298.28) [MB/s]
4K: 15.83 / 44.92 (s/b 21.70 / 62.60) [MB/s]
4K-64Thrd: 165.23 / 154.46 (s/b 241.38 / 234.08) [MB/s]
Acc.time: 0.218 / 0.294 (s/b .0186 / 0.208) [ms]
Score: 207 / 208 (s/b 314 / 327)
Overall Score: 533 (s/b 797)
One more note - it seems like my cooling fan is running at a high speed almost all of the time. This is probably one of my power settings (I think I have it set for max performance) but it's even doing this when there is no load (i.e. I'm using IE and just vieweing webpages - like right now).
So, I apologize for such a long post but I’ve spent countless hours researching and troubleshooting this problem and haven’t been able to figure out what the heck is wrong here. Am I missing something simple or do you guys think I have a SSD and/or problem with the machine itself? To say that any and all help would be greatly appreciated would be a massive understatement – I’m on the verge of pulling my hair out and I really need this machine working as quickly as possible!
Please let me know if you have any suggestions and/or need additional information. Thanks in advance for your help!
-Erik

Lol gotcha about the drive as an option. I didn't go SSD with mine. Do you have the latest firmware on your drive? It is supposed to be v1.97. Just checking (ah and I see item 3 so guess so). Do you have the SSD drive toolbox software installed?
http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Solid+State+Drives+and+Cach...)
Seems some useful tools are in there. I can't say much beyond that with the drive. Oh. Why does your fan always run at high speed? Can you describe that? I mean, are we troubleshooting the right kind of issue? Is there anything else going on with your system? I saw about the reduced core speeds message. what are your system loads like? Anything causing high cpu utilization? Could be something other than the drive causing your low numbers and lockups.

How to get Flash Builder problems tab (warnings and errors) in english

Hi,
my Flash Builder installation is showing the warnings and errors in Finnish. I get the idea behind this and the reason is good, as I'm native speaker of the language. Nevertheless it has some drawbacks when trying to resolve the issue by googling the error because Finnish is pretty marginal language and almost every Finnish Flex developer writes his/her posts in English. So either I have to try to guess the problems correct translation in English, which can be hopeless, or try to google it in Finnish which, as said, returns about zero results.
That said, I'm wondering if it's possible to change the warnings and problems in English? Do I need to reinstall Flash Builder to accomplish this?
Best regards,
Jukka Hämäläinen

Hi, thanks for fast reply.
Unfortunately I already tried that with no success. The strange thing is, that in my Flash Builder plugin directory in eclipse.ini the language was already declared as follows:
-nl
en_US
Didn't even touch that, it was there before and still my errors and warnings were (and still stay) in Finnish (everything else in Eclipse is in English).
Any thoughts?
Cheers,
Jukka

Sound problems - MSI Motherboard and drivers

message:-
I have an Evesham Microcomputer and am having difficulty with the sound - distorted and sometimes slow. I decided to use Live update to ensure I have the most upto date drivers for the sound card and chip set, both VIA.
Unfortunately I am having a trouble down loading these update and installing. All I get after a few minutes of the download screen is error code 997. Any ideas about the down load or sound problem? System info below.
regards
Nick
Motherboard MS-6340 ATX
VIA KT133A (VT8363A 552BGA & VT82C686B 352 BGA)
Audio Direct Sound AC97 Audio
Live update version 3.55
Chip set 4.37
Audio set version 6.14.1.3880
****************System Information****************
Motherboard MS-6340 ATX
VIA KT133A (VT8363A 552BGA & VT82C686B 352 BGA)
Audio Direct Sound AC97 Audio
Live update version 3.55
Chip set 4.37
Audio set version 6.14.1.3880
[MSI_Info]
OS Version: WinXP
LUS Version: 3.55.000
Language: 2057
MB Model Name: MS-6340
MB BIOS Vendor: Award
MB BIOS Version: 6.10
[OS]
Name: Microsoft Windows XP Home Edition|C:\WINDOWS|\Device\Harddisk0\Partition1
Manufacturer: Microsoft Corporation
Version: 5.1.2600
CSD Version: Service Pack 2
Windows Directory: C:\WINDOWS
Boot Device: \Device\HarddiskVolume1
Total Virtual Memory: 2048 MB
Free Virtual Memory: 2009 MB
Total Visible Memory: 256 MB
Free Physical Memory: 47 MB
Serial Number: 55277-OEM-0041603-32617
Install Date: 09/16/2005
Current Time Zone: Paris , Belgrade , West Central Africa
Locale: 0809
State: OK
[System]
User Name: NICHOLAS-STUDY
Description: AT/AT COMPATIBLE
Model: MS-6340
Manufacturer: MICRO-STAR INTERNATIONAL CO., LTD
Number Of Processors: 1
Total Physical Memory: 256 MB
System Type: X86-based PC
System Wake Up Type: LAN Remote
Power Supply State: 2
Power Manage. Support: null
Bootup State: Normal boot
[BIOS]
Name: Award Modular BIOS v6.00PG
Manufacturer: Award Software International, Inc.
Version: VIA694 - 42302e31
Serial Number:
Release Date: 12/18/2001
Target Operat System: Unknown
Language: n|US|iso8859-1
State: OK
[CPU]
Name: AMD Duron(tm) processor
Description: x86 Family 6 Model 7 Stepping 1
Manufacturer: AuthenticAMD
Processor Type: Central Processor
Version: Model 7, Stepping 1
Data Width: 32 Bits
Socket Designation: Slot A
Processor Id: 0383FBFF00000671
Processor Family: Power PC 604
Processor Stepping: 1
Max Clock Speed: 1202 MHz
Current Clock Speed: 1202 MHz
Current Voltage: 3.3 V
External Clock: 100 MHz
L2 Cache Size: 64 Kb
Availability: Running/Full Power
Power Manage. Support: false
State: OK
[Memory]
Name: Physical Memory
Memory Device Locator: BANK_0
Memory Bank Label: Bank0/1
Memory Capacity: 128 MB
Memory Total Width: null Bits
Memory Data Width: null Bits
Memory Type: Unknown
Name: Physical Memory
Memory Device Locator: BANK_1
Memory Bank Label: Bank2/3
Memory Capacity: 128 MB
Memory Total Width: null Bits
Memory Data Width: null Bits
Memory Type: Unknown
[Mainboard]
Name: Base Board
Manufacturer: MICRO-STAR INTERNATIONAL CO., LTD
Product Name: MS-6340(VT8363)
Version:
Serial Number:
[Sound Device]
Name: VIA AC'97 Audio Controller (WDM)
Manufacturer: VIA Technologies, Inc.
Product Name: VIA AC'97 Audio Controller (WDM)
Availability: undefined
Power Manage. Support: false
State: OK
[Network Adapter]
Name: RAS Async Adapter
Manufacturer: null
Product Name: RAS Async Adapter
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: WAN Miniport (L2TP)
Manufacturer: Microsoft
Product Name: WAN Miniport (L2TP)
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: WAN Miniport (PPTP)
Manufacturer: Microsoft
Product Name: WAN Miniport (PPTP)
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: WAN Miniport (PPPOE)
Manufacturer: Microsoft
Product Name: WAN Miniport (PPPOE)
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: Direct Parallel
Manufacturer: Microsoft
Product Name: Direct Parallel
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: WAN Miniport (IP)
Manufacturer: Microsoft
Product Name: WAN Miniport (IP)
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: WAN Miniport (IP)
Manufacturer: Microsoft
Product Name: WAN Miniport (IP)
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: Packet Scheduler Miniport
Manufacturer: Microsoft
Product Name: Packet Scheduler Miniport
Availability: Running/Full Power
Power Manage. Support: false
State: null
Name: BT Voyager 105 ADSL Modem
Manufacturer: BT
Product Name: BT Voyager 105 ADSL Modem
Availability: Running/Full Power
Power Manage. Support: false
State: null
[Video Controller]
Name: RADEON 7500
Current Refresh Rate: 75 Hz
Installed Drivers: ati2dvag.dll
Driver Version: 6.13.3276
Inf File name: oem1.inf
Availability: Running/Full Power
Monochrome: false
State: OK
[Video Configuration]
CheckBtn=ON

Well it looks like your board is an OEM board, which MSI doesn't officially support. But these drivers should work.
Chipset Drivers
Audio Drivers
Good Luck
Jeremy

Build Problems of dbxml-2.2.13 (with java enabled)

Hello,
I have tried building DB XML several times now without success. I am using the buildall.sh unix script.
Both with "--enabled-java" on and off the following error occurs after some time:
../os/os_open.c: In function `__os_mkdir':
../os/os_open.c:404: too many arguments to function `mkdir'
make: *** [os_open.lo] Error 1
I don't know what to do with this error. Can anyone help me, please?
Thanks.
P.S.: If needed, I will provide the whole config.log

I got the same problem
MinGW on Windows XP
when I tried to compile berkeleyDB part under the folder
c:\berkeleydbxml\db-4.3.29\build_unix\ make
$ make
/bin/sh ./libtool --mode=compile gcc -c -I. -I../dist/.. -O2 ../dist/../os/os_open.c
gcc -c -I. -I../dist/.. -O2 ../dist/../os/os_open.c -DDLL_EXPORT -DPIC -o .libs/os_open.o
../os/os_open.c: In function `__os_mkdir':
../os/os_open.c:404: too many arguments to function `mkdir'
make: *** [os_open.lo] Error 1
any suggestion, thanks
thanks

Problem in Webdynpro and Adobe form with signature field

Hi experts!
I have a problem with Signature Field in Adobe Form showed in a Web Dynpro Abap.
During the execution I fill the Signature field correctly but when I push any other button of the Webdynpro, the Adobe Form shows me the next error.
After click OK, the webdynpro is hang and not respond.
Any idea why not respond?
Thanks.

Hi friend,
Its not like that the Adobe created using SFP is non interactive.
We can create interactive forms using SFP transaction using java code.
I think it will be the problem with ADS just check with your basis people i think they will configure you the settings which works fine.
To check whether the settings are perfect you can try executing the standard programs FP_TEST_00 and
FP_PDF_TEST_00. If it works fine then some other problem exists else check with your basis team.
Just check this and revert me if you have any issues. I will help you
Thanks,
Sri Hari

Want to build an auto charging and discharging system with DAQ

Hi. I'm a freshman here. Now I have the DAQ-6009 and a labview software and some electronic elements. I wish to build a lithium ion battery cycles testing system (mainly for auto-switching) in order to observe the changes in the electrode. How can I build this charging and discharging system? The details of the battery are attached. Thank you!!
Attachments:
sanyo ml414 charging detaiils.pdf ‏75 KB

Hi freshman,
your spec sheet already mentions some resistors for loading and discharging your Li cell.
- With your USB6009 you can drive some transistors to switch between charging and discharging. You also have some AIs (analog inputs) to measure Li cell voltage as well as currents (when using some reasonable shunt resistors).
- Make an electronics sketch, read the manual of your USB6009 for it's specs and then grab your breadboard to build your electronics.
- Look at the examples coming with LabVIEW on how to switch DO signals and how to measure voltages (read the manual on that topics too!)
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Problem in creating (and opening) file with FileOutputStream

Hello,
I have a (java) program running on a linux server, and when it tries to create a new file, using FileOutputStream, it throws the following exception:
java.io.FileNotFoundException: /log/log_123.123.123.123_1842_09/03/2008_20:38:04.txt (No such file or directory)
        at java.io.FileOutputStream.open(Native Method)
        at java.io.FileOutputStream.<init>(FileOutputStream.java:179)
        at java.io.FileOutputStream.<init>(FileOutputStream.java:70)
        at shop.server.domainlayer.WriterInputProcessor.initialize(WriterInputProcessor.java:155)
        at shop.server.domainlayer.WriterInputProcessor.<init>(WriterInputProcessor.java:64)
        at shop.server.domainlayer.ShopUserDataWriterServer.main(ShopUserDataWriterServer.java:141)I don't understand why it fails, because I have the directory in the server's file system, and I'm trying to create an entirely new file.
Does anyone have an idea?
Thank you very much!

Thanks, the problem was that I had "/" in my file name, so the file system regarded it as a directory separator...

BIG whammy of a problem, code 1418 and folder icon with exclamation mark!!

I think my ipod's gone to ****. A while ago while walking home listening to my ipod, it just stopped. Looked at it and saw the folder+ !. I searched the net and saw that it probably just needed to be restored. So i tried to restore it, it froze. Updated to newest iTunes, but it wouldn't work on my comp. Anyways, I've formatted my comp, so i'm starting new here. My iPod still has that icon, so i connected it to my comp, and got it to start restoring, only part way through it to get the 1418 error code. It's an old 20gig 3rd gen, but it always worked fine. And actually now as I'm typing this, I can't get the bugger to connect to my comp anymore. It just keeps showing the folder icon. I have no idea what to do with this anymore. I've read tons of post in regards to 1418 but they're all in relation to nanos, video ipods, and shuffles. Any help would be amazingly appreciated because I can't afford a new iPod. Thanks!

i connected it to my comp, and got it to start restoring, only part way through it to get the 1418 error code
Let's get some information for the Apple Engineers. Please copy and paste these questions into an email, make the subject of the email "iPod error report", add your answers, and send the email to Roy at Apple.
1. What error code are you seeing?
2. When are you seeing it (restoring or updating your iPod)?
3. Which iPod do you have?
4. What version of Windows do you have?
5. What Windows service pack do you have installed?

MSI P67A-C45 Cpu temperature 127°c

Hi guys, i've bought new P67A-C45 with Intel i7 2600 box.
My machine measuring 127°C of cpu temperature during Intel burn test 2.5 at maximum:
Uploaded with ImageShack.us
But the system is stable and never blocked...Does mainboard have temperature's alert in bios' option? I'm not overclocking nothing and i've not activated oc genie 2... Any suggestion?

Realistically if you are stress testing and the gap between the core temps and the CPU temp is 50C + as in your case, then I would suspect a defective sensor for the CPU. Under full load with the standard Intel fan it is quite possible that the temps may end up in the mid 70s for the cores. But I think Mark is correct re the seating of the heatsink. DDR memory speed of 800 means its running at 1600, which would be correct if you have XMP enabled. With XMP disabled, it should probably be 667 or 533, depending what the SPD profile of the mem modules and if your mem modules are supported by your BIOS and correctly auto set.
The 127 reading as far as I know is the absolute max of the sensor. The sensor seems to be working as your minimum shows 105, so it may be the Fintek chip or whatever chip this board uses that may not apply the correct calibration. If your cores were also approaching the 100 mark then your MB BIOS would be throttling the CPU.
Seeing that your core temps are not "running away" my opinion remains a defective sensor. A BIOS update may solve this though. You will need to check.

MSI GTX560ti TwinFrozr2 (SLi) - Plz FFS Help :)

**Problem**
MSI GTX560ti TwinFrozr2 (SLi)
Straight from box - never overclocked anything tbh
275.33 Drivers
Samsung SM 2693HM 26"
Corsair TX 850w (recommended)
Win 7 64bit Ultimate
Other system hardware:
Intel 510 "Elemcrest" 120Gb SSD
2x WD Caviar Green 1TB HD
2x Pioneer DVR-261DBK 20x DVD RW SATA
6GB (3x 2GB)Corsair Dominator TR3X6G1866C9DF 1866Mhz
Intel Core i7 920 2.66Ghz (Nehalem)
Creative X-Fi Titanium Sound Card
Coolermaster Haf X Full Tower
Corsair Hydro H70 Liquid CPU Cooler
Gigabyte GA-X58A UD5 Mobo
Ok, until last week, I had a EVGA GTX295 card with no problems whatsoever but after installing the latest drivers - 275.33, completely at random times I would get the error: Display driver nvlddmkm stopped responding and has successfully recovered. This generally happened when I played either Fable or Dragon Age 2. Got lots of artifacting, black screen, the error and the game stopped responding. It has also happened whilst browsing Firefox or simply opening a folder in my PC, but generally in games. Anyway, obviously searched the net for possible causes and attempted to fix but nothing worked. As I am Mr Impatient, I drove from the NE of England to Scan and bought 2 MSI GTX560ti TwinFrozr2 (SLi) thinking my EVGA card was faulty. Installed the 2 new cards, 275.33 drivers (without the nvidia update or HD Audio drivers), fresh install of Win 7, same problem. I have tested my system memory, 3 passes on each stick with no errors. The PSU is a recommended one, although it is 2 years old, possible decrease in power and peformance? I am thinking it must be a driver issue and will rollback to a previous version later tonight and see if that helps. I have also heard that a possible problem with stock voltage? I have never OC anything before so am a little wary of changing voltages as I am not sure how to do it without screwing cards up. In MSI Afterburner Core Clock shows as 2100Mhz, Shader Clock as 1760Mhz and Memory Clock as 880Mhz. Apparently certified voltage is 822mhz, Factory out of box is set to 880mhz, but have no idea how to change this and tbh I shouldnt have too after spending all this £ on hardware.
Rolling back to 266 or 270 drivers did nothing. Temps are fine using 3d Mark/Unigine Heaven although I am getting the errors in 3dMark. I now reformatted, yet again, installed all latest hardware drivers, Mobo etc and the 270 nvidia drivers and I am still having problems. I dont have the facility of trying them in another PC but have tested cards one by one in PC and still get errors. Rang Scan up and all I got from there techs was, "me and a mate are running GTX460's in SLi using latest drivers and we have no problems". FFS, all I want is this sorted out. I spend loads with Scan and Overclockers and tbh support is rather cr*p (not you OC ). They say it is not the drivers, ok, the ONLY change I have done on my PC was install the nvidia latest drivers on my GTX295 and thats when the errors started happening. New cards and same problem. I am seriously considering taking my PC down to them and getting them to see the errors and damn sort it for me :(
Further, memtestG80 and memtestCL both reported zero errors on both GPU's. Ran Unigine Heaven again and got as far as stage 20 and got error again, can hear the music in the background, system then crashes alt tab wont work, ctrl alt del wont work and reboot only option. 3DMark errored with some kernel error. Formatted again installed 266 drivers again same errors but this time when I try to update to 270/275 drivers I get a failed install.
Any help would be greatly appreciated guyz

Svet you were correct, I took the 2nd card out and ran Unigine Heaven and 3DMark and it passed twice no problems. Switched the cards over and I got the error within 20 seconds of Unigine Heaven and couldnt get past Test 2 in 3DMark, tried that one twice too and failed both times. Just spoke to Scan and they said bring it back and they will actually test the replacement card for me before I leave
Damn what a simple solution all this time :/

Transport roles and analysis authorization with user assigned

Hi expert,
I face with this problem transport roles and analysis authorization with user assigned. When I have created a transport request to move the roles and analysis authorization from development system to test system. I couldnu2019t maintain the user assigned, after transport I have to assigned manually all of user or create a program to fill AGR_USER table or there are other way.
Thanks for your time,
Luis

Hi,
In role administration, you have the following options for transporting roles:
You can download the roles from one system and upload them into another
You can import the role from a remote system using RFC
You can transport the roles with the transport function.
Role upload loads all role data, including authorization data from a file into the SAP system. The user assignments for the role and the generated profiles for the role are exceptions in this case.
Transporting Roles with the Role Transport Function
       1.      Start the role administration function by choosing Tools ® Administration ® User Maintenance ® Role Administration ® Roles (transaction PFCG).
       2.      Enter the role to be transported and choose Transport Role.
The Mass Transport of Roles screen appears. You can control the default settings for the options Also transport single roles for composite roles and Also transport generated profiles for roles using Customizing switches (see Role Administration Functions in the section Functions of the Utilities Menu).
You should not change the authorizations profiles of the role after you have included the role in a transport request. If you need to change the profiles or generate them for the first time, transport the entire role again afterwards.
For more information go thrpugh the below link
http://help.sap.com/saphelp_nw70/helpdata/EN/6d/7c8cfd410ea040aadf92e1f78107a4/content.htm
Regards,
Marasa.

MSI P67A-C45 B3 Problems

Hello,
I recently bought a main board MSI P67A-C45 B3 from a shop in my country ( Romania ) and i had a problem with it as soon as it got home.
I installed all the new components that i got, plugged all the devices, but my computer did not start. I pushed the power on button, but it only stayed on for like 2-3 seconds and then turned off, and it repeated this cycle without me having to push the power on button. I took all the components to the shop i bought them from, so they could tell me whats there to do with my new computer. After a couple of hours they called me and told me that the main board had one pin bent in the CPU slot. I don't think that i could have bent one pin, I've done this before in the past, and this never happened to me.
What I'm really asking :
Is it possible, out of 1155 pins , for only one pin to be bent when plugging the CPU in its slot ?
And ,
Can one bent pin be the cause of my computers problem ?
Was i just scammed and put to pay another main board, or is it true what they are telling me ?
Thanks

Yes, just one bent pin can cause this, you can fix this probably though.
*You can bend those pins by breathing on them too heavily (joke) don't feel like you are the only one to do this.
Get a really bright light and a magnifying glass and find the pin and move it back into place with an eyeglass screw driver or other very small object.
You also may be able to get msi to repair it for you.
If you can get it fixed yourself, try MSI:
>>How to contact MSI.<<

Build Problems, MSI GTX560ti and P67A-C45 with i5

Similar Messages

Maybe you are looking for