Building Cisco 7200 VXR

Hi,
I have a Cisco 7200 VXR chassis. What cards I have to buy to mount a VoIP Gateway, with SS7 E1 ports to trunk with the PSTN networks?
Best Regards.

You can use Cisco MIX-enabled T1/E1 Port Adapter. For more information kindly refer the url's below,
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800afd65.shtml
http://www.cisco.com/en/US/products/hw/modules/ps2033/ps1952/index.html

Similar Messages

IPv6 on CIsco 7200 VXR series router

Dear Friends,
I want to know, whether cisco 7200vxr router support ipv6? I want to use both ipv4 and ipv6. In that case whats about the performance.
Do i need IOS upgradation to acheive this implementation.

Hi -
Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
However, it appears that ipv6 is not supported in this s/w version:
ITP1#sh version
Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 23-Sep-08 19:48 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
ITP1#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ITP1(config)#ipv6 ?
% Unrecognized command
My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
Thanks,
Matt

GETVPN Key server Cisco 7200

Hi,
I am using Cisco 7200 NPG1 as Key server for GETVPN. I have almost 500 Spokes. How many concurrent IKE sessions could be supported by 7200 box ?
I have heard that simultenous session limit for IKE is 100 ?
regards
Prasad K

I have heard that simultenous session limit for IKE is 100 ?
This is true to software crypto.
You get best scaling factor on 7200 with VSA. 500 seems a decent number. Are you seeing any problems?

How to Gatekeeper on cisco 7200

How can i enable my gatekeeper on cisco 7200 my current IOS is 12.1.(2)T i cannot enable my gatekeeper it seems to be working before.
hope you can help me.
thanks

Does rolling back to previous version help. If so you could search for any potential bugs in 12.1.(2)T or try loading the latest version.
My search on bug toolkit with "Gatekeeper" keyword on this release got me 240 bugs. I am not sure which one is yours. So better try with the latest version

Multilink limitations application on Cisco 7200 Series

Hi,
Can someone please mention if Multilink can be supported on Cisco 7200 Series?
IOS version:
IOS 7200 Software (C7200-P-M), Version 12.3(16a), SOFTWARE (fc2)
cisco 7206VXR
Any comment will be appreciated.
Thank you.

Hi -
Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
However, it appears that ipv6 is not supported in this s/w version:
ITP1#sh version
Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 23-Sep-08 19:48 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
ITP1#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ITP1(config)#ipv6 ?
% Unrecognized command
My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
Thanks,
Matt

Cisco 7200 as managed cpe with mpls enabled

Is there any real network that is using managed CPE (CPE router managed by SP) with mpls enabled (MPLS-TE, VPN) etc.
Is anybody using cisco 7200 as a managed cpe router with mpls.
Thanks.
subodh

with PE router, Service provider handles so many CE routers (of customers).
Managed CPE router will be placed at the customer site and will handle only one customer.
Is there any company/customer that have so big network that they need cisco 7200 at there site and this CPE does MPLS-TE,MPLS-VPN.
could u pl. name some companies that are availing this king of services from service provider.
{as cisco 7200 is also capable of providing voip solution to customer}.

Cisco 7200 as BRAS

Hi,
does anyone of you know if you can use a Cisco 7200 as a BRAS? We were told it is possible, but I am not able to find an IOS image with PPPoE support.
Any pointers are welcome.
TIA
NaNa

As far sa I know, you can get ISG
(http://www.cisco.com/en/US/products/ps6566/products_configuration_guide_book09186a008061ab53.html)
features on 7600 platform but only for IP sessions, not for PPP.
These functions should be available on on SIP-400.

Cisco 7206 vxr to ASR 9000 BGP config migration

Hi,
I had a cisco 7206 vxr. I have just ASR 9000. I'm going to replace c7206vxr to ASR9000. I can tried to bgp config but I didnt see distribute-list for ASR9000.
c7206 config are below:
router bgp 100
no synchronization
bgp log-neighbor-changes
bgp suppress-inactive
neighbor 10.10.10.54 remote-as 101
neighbor 10.10.10.54 description *** ISP1 ***
neighbor 10.10.10.54 password 0 test
neighbor 10.10.10.54 update-source GigabitEthernet0/2.387
neighbor 10.10.10.54 prefix-list RED in
neighbor 10.10.10.54 distribute-list 12 out
neighbor 10.10.10.54 route-map PREF in
neighbor 10.10.10.54 route-map FAR out
neighbor 10.10.10.54 filter-list 9 in
ip prefix-list RED seq 2 deny 192.168.0.0/25
access-list 12 permit 192.168.96.0 0.0.3.255
ip as-path access-list 9 permit ^(101_)+
route-map PREF permit 10
set local-preference 150
route-map PREF permit 20
route-map FAR permit 10
match ip address example
set as-path prepend 100 100 100
route-map FAR permit 10
My ming so confused. Could you help me somebody ? How can migrate this config for the ASR9000 format?

Hello Umit,
The functionality is done with RLP as well. Here is the quick example. (note, I didn’t verify on a life router, but you should get an idea on how to implement it).
prefix-set pfx_acl_12_p1_permit
192.168.96.0/22 ge 22
end-set
route-policy FAR
   prepend as-path 100 3
end-policy
route-policy policy_nbr_10_10_10_54__ipv4_unicast_out
if (destination in pfx_acl_12_p1_permit) then
   apply FAR
endif
end-policy
router bgp 100
bgp log neighbor changes
neighbor 10.10.10.54
remote-as 101
description *** ISP1 ***
password clear Test
update-source Gigabitethernet0/0/0/2.387
address-family ipv4 unicast
   route-policy in
   route-policy policy_nbr_10_10_10_54__ipv4_unicast_out out
Regards,
/A

Cisco 7200 VSA issue after upgrade to IOS 15.2

After upgrade to IOS 15.2(4), VSA module in 7206VXR (NPE-G2) is disabled and we cannot enable it.
Show diag output:
------------------ show diag ------------------
Slot 0:
VSA IPsec Card Port adapter
Port adapter is deactivated
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
PCB Serial Number        : JAF1309ADDT
Hardware Revision        : 1.0
Part Number              : 73-10220-05
Board Revision           : B1
RMA Test History         : 00
RMA Number               : 0-0-0-0
RMA History              : 00
Deviation Number         : 0
Product (FRU) Number     : C7200-VSA
Version Identifier       : V01
Top Assy. Part Number    : 68-2578-05
CLEI Code                : CNUCAFNAAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 4A 41 46 31 33 30 39 41 44 44 54 40
0x10: 05 0D 41 01 00 82 49 27 EC 05 42 42 31 03 00 81
0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 43 37 32
0x30: 30 30 2D 56 53 41 20 20 20 20 20 20 20 20 20 20
0x40: 20 89 56 30 31 20 D9 03 C1 40 CB 87 44 0A 12 05
0x50: C6 8A 43 4E 55 43 41 46 4E 41 41 41 FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
If we try to enable it manually from CLI we get the following message:
Router(config)#crypto engine slot 0
VSA will NOT come up until system power-cycle or reload
Of course, after reload nothing happens.
Is VSA incompatible with IOS 15.x? I'm asking because downgrade to 12.4 causes VSA to be active again.
Regards,
Igor

Hi igor,
1) FDP image
Field-programmable devices (FPDs) are hardware devices implemented on router cards that support separate software upgrades. An FPD image package is used to upgrade FPD images
The FPD image package must be compatible with the Cisco IOS software that is running on the router. If an incompatibility exists between an FPD image package and the Cisco IOS software release running the router, the device with the FPD will not operate properly until the incompatibility is resolved.
The FPD automatic upgrade feature searches only for the FPD image package file that is the same version number as the Cisco IOS release being used by the system. For example, if the Cisco IOS release being used is Cisco IOS Release 12.4(5)T1, the system searches for the FPD image package file that supports the specific Cisco IOS release (c7200-fpd-pkg.124-5.T1.pkg).
2) Steps to Upgrade:
From the document below which I already sent you, please refer to the section “How to Upgrade Field-Programmable Devices”
http://www.cisco.com/en/US/docs/routers/7200/configuration/feature_guides/fpd.html
I would recommend you to follow the steps in the “Field-Programmable Device Quick Upgrade (Automatic FPD Upgrade Only)” as that is the recommended and the easiest way.
Steps are:
The command is present “upgrade fpd auto” in the running-config by default.
Have the Cisco IOS image in disk2:
Download the FPD image package to disk2: flash disk
Reboot the router using the new Cisco IOS release.
Hope this helps
Thanks
Syed

Cisco 7200 ip interface issue

I have a 7200 already configured with a cable modem interfaces working just fine with ios ver 12.2(15)BC2e.
I just got another 7200 with the same cable card with ios ver Version 12.2(33)SCB4 for another site
the plan was to simply copy the working config to this one and walk away.
unfortunately i can no assign an ip to the cable interface, but successfully assigned an ip to the gig interface.
the only clue i can see is the out from the new 7200
BC_CMTS#sh ip int cable 3/0
Cable3/0 is administratively down, line protocol is down
Internet protocol processing disabled
any ideas would be greatly appreciated,

thanks for the quick reply. the port was disabled at that point and time, but has nothing to do with the issue.
quite simply put, when i try to configure an ip address on the cable card, i get the typical "
% Invalid input detected at '^' marker." error message. When I type "ip ?" under that interface there is no address option.
just to recap this config works just fine on my other 7200 and cable card, but this 7200 has a newer IOS.
any insight or ideas would be greatly appreciated.
regards

CAR on Cisco 7200

I' ve tried with success to set a reserved bandwidth for 2 different lan passing throught the 7200 serial.
Any know how to set a dynamic Car to use all the available bandwidth in every moment?
Cause I' v seen this kind division is static!
Here what i ve configured on this serial!
rate-limit input access-group 102 1096000 256000 350000 conform-action transmit exceed-action drop
rate-limit input access-group 103 896000 128000 256000 conform-action transmit exceed-action drop
rate-limit output access-group 2 1096000 256000 350000 conform-action transmit exceed-action drop
rate-limit output access-group 3 896000 128000 256000 conform-action transmit exceed-action drop

Hello,
The problem description sounds like policing is not required, but queueing. As far as I understand you want to give minimum bandwidth guarantees to each LAN and allow for utilizing up to the max bandwidth available.
CBWFQ will do exactly that. An example config:
ip cef
class-map match-all LAN1
match interface FastEthernet0/1
class-map match-all LAN2
match interface FastEthernet0/2
class-map match-all class-default
match any
policy-map 4SerialOUT
class LAN1
bandwidth percent 30
class LAN2
bandwidth percent 30
class class-default
fair-queue
interface Serial1/0
bandwidth 1024
service-policy output 4SerialOUT
This would guarantee 30% of the bandwidth at the Serial to all traffic from LAN1 and 30% to LAN2. In case there is no other traffic each LAN could use the full Serial bandwidth. You would need to adjust numbers and interfaces to your needs.
Hope this helps! Please rate all posts.
Regards, Martin

Cisco 7200 HSRP Dual-Stack

Hi;
May i use HSRP for ipv4 and ipv6 at the same time on same interface ?
Our interface;
interface GigabitEthernet0/3
description Firewall
ip address 193.x.x.x 255.255.255.192
ip flow ingress
ip policy route-map network-load
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
standby 3 ip 193.x.x.x
standby 3 priority 130
standby 3 preempt
we want to use 2001:047c:xx::5 for standby ip.
for nodes:
2001:047c:xx::6
2001:047c:xx::7
Is it possible ?
Thanks

Hi,
What feature set i.e Enterprise Services, IP services, etc...?
sh ver | inc bin
Is that NPE-G1 or G2?
HTH

Alternative for VRF Source Select

We have "VRF Source Select" configuration alternative to Policy based Route-map in the Router Interfaces .Can anyone tell me if we have any alternative for "VRF Soure Select" . Unfortunately Cisco 7200 VXR NPE-G1 Routers doesn't this feature at all. NPE-G1 supports only VRF Forwading and VRF Site-maps!!!
Regards
Srikant

I can't think of an alternative but 12.0(28)S, which is planned to be on CCO at the end of April, will support the NPE-G1. This should solve the issue.
Hope this helps,

MPLS over GRE Support (Platform)

Hello,
I am looking to run MPLS over GRE (over the Public Internet) probably with IPSec for obvious reasons. CFN seems to suggest only the Cat6k with SUP-VS-2T or the Catalyst 6800 is capable of MPLS over GRE functionality...
I currently have 2 x Cisco 7200 VXR platforms (7204 & 7206) with the NPE-G2 processing engine and was wondering if we added the VSA encryption module (C7200-VSA=) would be enough to get a reliable MPLS over GRE tunnel functionality.
The tunnel with Encryption would ideally support up to 500Mbps.
My other alternative is to upgrade/replace the VXRs with ASRs (1002 or similar) but again CFN is unclear if the ASR100x platform is capable of delivering MPLS over GRE + IPSec.
Thanks,

MPLS over GRE is not supported in Hardware for sup720. This is a PFC3 hardware limitation. Your options would be to use SPA-400 or Enhanced FlexWan.

Is high availability suppoted on SOHO routers?

Hi Everybody,
I am looking for SOHO series routers to be placed at branch offices which would support HA, GRE IPSEC VPN, IOS Firewall Feature set, and VOICE.
does anyone knows the answer to the above.?

Syed,
To answer your questions, here is the link that explains about the features on the SOHO routers
http://www.cisco.com/en/US/products/hw/routers/ps4866/products_data_sheet09186a008010e5c4.html
But, I do know that IPSec HA is supported only on some of the platforms. Here is the snippet from Cisco's web site
"IPsec HA is supported only on limited hardware. The hardware list includes Cisco 7200 VXR (NPE-400, NPE-G1) Series router, Cisco 7301 Router, and Cisco 3725 and 3745 multiservice access routers."
http://www.cisco.com/en/US/products/ps6660/products_white_paper0900aecd80278edf.shtml
Hope this explains your queries.
Rate this post, if it helps!!
Cheers
Gilbert

Building Cisco 7200 VXR

Similar Messages

Maybe you are looking for