Building to building Bridge link using Aironet 1300's

We have a requirement to link two adjacent buildings that are about 20-metres apart over a public road. I need some advice on what the best solution will be.
Initial thoughts are a pair of Aironet 1300's configured as Wireless Bridges but the antenna type and where to mount them is confusing me. Will the internal patch antennas be enough for this or will we need external antennas? If so what type - directional or? Do the AP's need to be mounted externally or can we simply mount them internally facing each other through windows? What do we need to be aware of regards signal overlaps and interference etc?
What looked like a simple setup seems to have opened a can of worms....
Thanks
Andy

Hi Andy,
The 20m distance is quite short.
In this case, as recommended by Cisco*, for AP1300 series, you can use the AIR-ANT2410Y-R antenna. This directional antenna can be used/installed indoor or outdoor.
Approximate Indoor Range at 6 Mbps : 548 ft (167 m)
Approximate Indoor Range at 54 Mbps: 165 ft (50 m)
*http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022198b.html
Look under 'Table 4. Antennas for the Cisco Aironet 1300 Series Outdoor Access Point/Bridge with RP-TNC Type Connector'.
Both AP1300 and the antenna can be installed indoor. You need to wall-mount the antenna facing each other from each building.
Since the distance is only 20m, you can play around with the transit power to control the signal distance.
As for overlapping channel & probability of interference, do a simple site survey (can use freeware NetStumbler) and make sure your antenna does not mounted near equipment like microwave, or any equipment that produced high frequency noise.
Hope this helps.
Rgds,
AK

Similar Messages

  • Encrypting Aironet 1410 bridge link using multiple VLANs

    I've looked at the documentation available for Aironet 1400 series, and still would like to see a single document showing an example of
    the best encryption/authentication available for bridge links using multiple VLANs.
    As I understand it, 1400 series can support WPA-PSK using AES, which would work for me.  I just can't picture how to integrate chapters 9 and 10 for the 'WEP and WEP Features' + 'Configuring Authentication Types' instructions.
    I'm looking either for an example config, or a step-by-step that did all steps consecutively.
    Thanks

    What doc are you refering to?  If you want to encrypt the link from root bridge to non-root bridge, then WPA/TKIP-PSK is what you should use.  Here is a link to how to setup your link ssid to WPA: http://www.cisco.com/en/US/docs/wireless/bridge/1400/12.2_15_JA/configuration/guide/p15auth.html#wp1044935
    Don't worry about the example they show on the WEP, just use the configuration from the above link for your encryption.
    Configuring a VLAN
    Configuring your bridge to support VLANs is a five-step process:
    1. Create subinterfaces on the radio and Ethernet interfaces.
    2. Enable 802.1q encapsulation on the subinterfaces and assign one subinterface as the native VLAN.
    3. Assign a bridge group to each VLAN.
    4. (Optional) Enable WEP on the native VLAN. <-- Use WPA-PSK
    5. Assign the bridge's SSID to the native VLAN.
    http://www.cisco.com/en/US/docs/wireless/bridge/1400/12.2_15_JA/configuration/guide/p15vlan.html
    Here is an example of vlan 1 (native) will be your management and your wireless link.  vlan 10 & 20 will pass through the link.
    BR# configure terminal
    BR(config)# interface dot11radio0.1
    BR(config-subif)# encapsulation dot1q 1 native
    BR(config-subif)# bridge group 1
    BR(config-subif)# exit
    BR(config)# interface fastEthernet0.1
    BR(config-subif)# encapsulation dot1q 1 native
    BR(config-subif)# bridge group 1
    BR(config)# interface fastEthernet0.10
    BR(config-subif)# encapsulation dot1q 10
    BR(config-subif)# bridge group 10
    BR(config)# interface fastEthernet0.20
    BR(config-subif)# encapsulation dot1q 20
    BR(config-subif)# bridge group 20
    BR(config-subif)# exit
    BR(config)# interface dot11radio0
    BR(config-if)# ssid batman
    BR(config-ssid)# vlan 1
    BR(config-ssid)# infrastructure-ssid
    BR(config-ssid)# end

  • Aironet 1300 radio keeps on shutting down

    Hi,
    I have a problem with the wireless bridge connection using aironet 1300. It work fine before.no changes were done. The problem is that the radio keeps on shutting down.in the web interface radio is enabled but down. i have to manually diable it then enable it back to resolve the issue. Problem is random and this is happening on both aironet. Below is the log.
    on the first aironet:
    1 Mar 31 02:20:59.444 Error Interface Dot11Radio0, changed state to up
    2 Mar 31 02:20:59.443 Warning Interface Dot11Radio0, Associated To AP UPAdminBridge 001e.4a05.b820 [None]
    3 Mar 31 02:20:59.389 Error Interface Dot11Radio0, changed state to down
    4 Mar 31 02:20:59.339 Warning Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
    5 Mar 31 01:24:51.062 Error Interface Dot11Radio0, changed state to up
    6 Mar 31 01:24:51.061 Warning Interface Dot11Radio0, Associated To AP UPAdminBridge 001e.4a05.b820 [None]
    on the second aironet:
    1 Mar 17 09:30:42.107 Information Interface Dot11Radio0, Station UP-ASBridge 001e.f7f1.abc0 Reassociated KEY_MGMT[NONE]
    2 Mar 17 09:30:41.971 Information Interface Dot11Radio0, Deauthenticating Station 001e.f7f1.abc0 Reason: Previous authentication no longer valid
    3 Mar 17 09:30:41.971 Warning Packet to client 001e.f7f1.abc0 reached max retries, removing the client
    regards,
    Christian

    Verify that when the radio interface is shutdown, the workstations can connect to the server immediately. Also ping from the AP to server and workstations to verify if there is any difference seen to the results seen prior to the radio interface being shut down.

  • Bridge 1300 building to building link for VOIP Data Rates settings and QoS

    Hi,
    What are the recomendations for data rates settings of wlan fo using voip in a link building to building.
    Default is
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
    54.0
    Should i maintain or change to what?
    Also what QoS should i apply?
    Thks
    Best Regards
    Marco

    OFDM is a physical layer encoding technology for transmitting signals through the RF. This method breaks one high-speed data carrier into several lower-speed carriers that transmit in parallel across the particular RF spectrum. OFDM, when used with various modulation types such as 802.11g and 802.11a, is capable of supporting data rates as high as 54 Mbps.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/5_0_1/english/administration/guide/7921wrnt.html#wp1085347

  • Secure Wireless Site to Site Bridge - Aironet 1300 or 1252?

    Hi there,
    We're planning to connect a building no more than 50m away to our network via wireless (after careful research. The builing will only house 2 people, one requiring just internet and email access for ordering materials, the other will be doing document scanning - currently scanning files of roughly 15Mb every 3-5 minutes to an SQL server in the main building. They will also need to retrieve similarly sized files from said server within the same timescale. The solution would need to offer WPA2 security and a hidden SSID.
    I have been pointed in the direction of the Aironet 1100 which now appears to be discontinued, so the Aironet 1300 was suggested instead. Will this 54g device be sufficient for the activities above and if so, I guess I will just need to configure each unit as a bridge (1 per building?)
    I have also been looking into N type devices and found the Aironet 1252 but I believe that this is an internal device? I have the facility to locate it by a window/ very close to the outside of the building on both sites but not sure if this would be cost effective. Am I right in thinking the 1252 would require me to purchase additional antenna to go with it? If so, what type would be suitable as there are several listed on the site.
    Finally. I'd like the solution we go with to be expandable (if it allows) as another building within the same area is also being looked at and would benefit from having a similar connection to it. Whether the bridging would allow for this, or another 2 units would need to be purchased is something I am unsure of.
    I'd really appreciate some feedback from someone with experience of both units or experience in setting up a similar configuration as I am quite new to this side of wireless
    I have included a basic Visio diagram of my proposed configuration; I hope it is of some use.
    Thanks in advance.

    Hi,
    the 1310 will offer sufficient throughput. But if you add buildings, maybe you will start reaching the limit ...
    The problem with the 1250 is that it's not meant to go outdoor as it is, apart from that it's perfect for the job.
    The type of antennas strongly depend on the location of the building.
    If the 3 buildings are in a line with the main building in the center, you will need an omnidirectional antenna. The point is that your bridges should all hear each other, so their coverage zone should include all other bridges. Then it's possible to have one AP at each site, the main site AP being "root" and the other being "non-root". If too hard, you could also go with 2 APs at the central site and then you can go with directionnal antenna toward each building.
    And the 1310 can come either with an internal antenna that is very directionnal or with external antennas connector. The 1250 is always for external antennas.
    Note also that the 1250 requires a bit more power than normal PoE allows.
    I hope this helps,
    Regards,
    Nicolas
    ===
    Don't forget to rate answers that you find useful.

  • Need help on Aironet 1300 bridges

    Greeting,
    We have just upgraded two Aironet 1300 bridges (from cisco 350) on two buildings about 100 yards apart. They are only running as bridges. One is set up as root bridge and another one is setup as non-root bridge. Root bridge is in the main building direct connect to Cat 4506. For some reason the root bridge has some intermittant problem connect to the network. We are running the IOS 12.3(8). We changed the cable but the problem still occured. Everytime we have to reboot the root bridge in order to get it back. but all the interfaces in the root bridge show " up / up" prior to reload. The "show tech" looks fine on the root bridge. Any suggestion? Shall I change root bridge to workgroup bridge?
    really appreciate for any helps,
    Gene

    Hi Steprodr,
    I just need to clearify that the power injector is on the non-root bridge? I think the power are fine on both bridges when the problem occured. We used cisco 350 bridges before the upgrade. So the cable and port are still remain the same. The problem is more going towards from root bridge come back to Cat 4506 because both root and non root bridges can ping each other when the problem occured.
    thanks,
    Gene

  • Deos Aironet 1300 can provide the repeater mode to PT-link TL-WA601G

    Hello,
    I have a problem with Aironet 1300 to provide the repeater mode to PT-link TL-WA601G for extending the signal.
    I have two cisco aironet, i have configures as the bridge to link each other and WEP 128bit key.
    Then i bought TL-WA601G for extending the signal to my room. However after i configure on TL-WA601G as the repeater mode and put WEP 128bit key, TL-WA601G cannot get sent and received packets from Aironet.
    So what is the problem on this? How can i solve this issues?

    Cisco Aironet products can establish 40-bit Wired Equivalent Privacy (WEP) connections with IEEE 802.11b-compliant non-Cisco products. If you want to create a 128-bit WEP link, Cisco products only interact with other Cisco products. If you are using a third-party device with a Cisco Aironet product, you must set both devices to use 40-bit WEP.

  • 1310 Bridge-Building to Building advice.

    I am looking at implementing building to building wireless using Cisco 1310 bridges. This would be a backup link between the 2 buildings. The primary link is 3 T-1's. There are about 250 users connecting back here for application and internet. I am assuming that since the speed over the wireless is more than the existing T-1's that there shouldn't be a problem with latency. Am I missing anything with my thinking?
    Thanks

    Hey there,
    If you use a BR1310 to cover 3 T1s you should be fine.
    The BR1310 can get up to 54mbs (28mbs in reality due the the nature of half duplex devices such as these bridges).So even with less than ideal signal quality and strength you should have no problem getting that kind of throughput.Ideal links get in the low to mid 20s.
    Hope this helps.
    Regards,
    Aaron

  • About Aironet 1300 Outdoor Bridge.

    Hi,
    I have a question about Aironet 1300 series Outdoor Bridge.
    in case of 1300 series, it is supporting with 802.11g protocol. BTW, I wanna use it with 802.11a protocol on Aironet 1310 series. Is it possible ?
    If so, how to do I have to it ?
    I wait your good answer.
    Thanks.
    Best Regards.

    1310 only support 11b/g, not support 11a.
    1410 support 11a

  • Security on Aironet 1300 bridges

    I am a newbie on this fourm. I required your suggestions and recommendations. I have aironet 1300 bridges. I want to connect them in point to multipoint envt.
    I want to have one root bridge and rest as non root bridges. But i want to implement authentication of non-root bridges through root bridge. Please suggest what is the latest and strongest authentication and security protocols that i can use. Please i am looking for an early response.

    EAP Authentication type provides the highest level of security for your wireless network. By using the Extensible Authentication Protocol (EAP) to interact with an EAP-compatible RADIUS server, the root access point/bridge helps another access point/bridge and the RADIUS server to perform mutual authentication and derive a dynamic unicast WEP key. The RADIUS server sends the WEP key to the root access point/bridge, which uses it for all unicast data signals that it sends to or receives from the non-root access point/bridge. The root access point/bridge also encrypts its broadcast WEP key (entered in the access point/bridge's WEP key slot 1) with the non-root access point/bridge's unicast key and sends it to the non-root access point/bridge.

  • Aironet 1300 Point to Point Bridging

    Hi, I am new to the forums so please accept my apologises if this is really easy question!!
    We have purchsed 2 Aironet 1300's that we are wanting to use to create a bridge, but after hours of trying and net searching we cannot get them to talk to each other. Can anyone please help? Thanks

    Here's the online config guide:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
    Here's the Point-to-Point Troubleshooting FAQ:
    http://www.cisco.com/en/US/products/hw/wireless/ps2360/products_qanda_item09186a00801d29ff.shtml
    Wireless Point-to-point Troubleshooting Guide:
    http://www.cisco.com/en/US/products/hw/wireless/ps2360/products_tech_note09186a00801d2a0c.shtml
    Sample Config and Command Guide:
    http://www.cisco.com/en/US/products/hw/cable/ps2217/products_configuration_example09186a0080193dac.shtml
    Other possible issues are to make sure you have solid line-of-site ("more than you think you need" because of some properties associated with the "Freznel Zone")
    Check it out and let us know if you are still having problems.
    Good Luck
    Scott

  • Aironet 1300 Bridge and AP simultaneously

    Hello Everybody I`ll like to use the Aironet 1300 in a Bridge and AP operation simultaneously and I`ll use a Omnidirectional Antenna ANT-2506 to cover clientes. The question is if in this design the non root AP/bridge operate like repeaters and what about the Bandwith. does this anntena work for a AP application? What is the coverage with this anntena for clients and others bridges.
    My scenario is a Root 1300 with Antenna ANT-2506 for clients and bridges and 5 1300 (non root) with Antenna ANT-2506 for clients and bridges.
    Thanks in advance!

    The flexibility of the Cisco Aironet 1300 Series allows it to operate asa wireless bridge, access point, or a workgroup bridge.
    http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_chapter09186a00804158b6.html

  • Wireless link(bridge) between two ap 1300

    Hello, i need to configure wireless link between my 1300 series, how can i use them like a bridge and access point in the same time?
    Do i need static ip for BVI interfacess between them for bridge or its need to be DHCP, is there any example? i would be great to know that
    thank you

    Here is a simple config example
    Root                                                                           Non-Root
    R(config)#dot11 ssid test                             n-R(config)#dot11 ssid test
                    #authentication open                    n-R(config)#authentication open
                   #infrastructure-ssid                       n-R(config)#infrastructure-ssid
                   #exit                                                                  #exit
    R(config)#int d0                                          n-R(config)#int d0
                   # ssid test                                                  #ssid test
                    #statio-role root bridge wireless-client          #station-role non-root bridge wireless-client
                    #no shut                                                   #no shut
    For BVI interfaces you can assign either static or dynamic IP address
    But it is highly recommended to have static ip for better management.

  • Ejbmodule error while building the external service app using web service

    Hi,
    I am new to SOA. I have developed an external service application using web service. While buiding the project i am getting the ejb module error which is mentioned below and the remaining five internal projects are getting deployed successfully. Can anyone help me out in resolving this issue.
    Apr 17, 2008 3:51:45 PM /userOut/Development Component (com.sap.ide.eclipse.component.provider.listener.DevConfListener) [Thread[ModalContext,5,main]] ERROR: user_example/ejbmodule: Build failed for sap.com/user_example/ejbmodule(MyComponents) in variant "default": Compile failed; see the compiler error output for details.
    Build log -
    Development Component Build (2008-04-17 15:51:39)
      Component name: user_example/ejbmodule
      Component vendor: sap.com
      SC compartment: MyComponents
      Configuration: LocalDevelopment
      Location: local
      Source code location: mzwrxw@w2mzwrxw01
      DC root folder: D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\
      DC type: J2EE
      DC subtype: EJBModule
      Host: w2mzwrxw01
    DC Model check:
       All used DCs are available locally
       validating dependency to build plugin "sap.com/tc/bi/bp/ejbmodule"
       validating dependency to  public part "default" of DC "sap.com/ejb20"
       validating dependency to  public part "default" of DC "sap.com/jdbc20"
       validating dependency to  public part "default" of DC "sap.com/jms"
       validating dependency to  public part "default" of DC "sap.com/tc/ddic/metamodel/content"
       validating dependency to  public part "CAFRuntimeAPI" of DC "sap.com/caf/runtime/impl"
       validating dependency to  public part "compilation" of DC "sap.com/caf/runtime/api"
       validating dependency to  public part "default" of DC "sap.com/bi/mmr/core"
       validating dependency to  public part "compilation" of DC "sap.com/caf/metamodel"
       validating dependency to  public part "default" of DC "sap.com/com.sap.security.api.sda"
       validating dependency to  public part "default" of DC "sap.com/tc/logging"
       validating dependency to  public part "default" of DC "sap.com/com.sap.exception"
       validating dependency to  public part "default" of DC "sap.com/com.sap.jdo"
       validating dependency to  public part "compilation" of DC "sap.com/bi/mmr/cwm_1.0_source"
       validating dependency to  public part "jmi" of DC "sap.com/bi/mmr/jmi"
       validating dependency to  public part "ClientApi" of DC "sap.com/caf/km.proxyjava"
       validating dependency to  public part "default" of DC "sap.com/bi/mmr/db"
       validating dependency to  public part "ClientAPI" of DC "sap.com/caf/runtime/security"
       validating dependency to  public part "ClientAPI" of DC "sap.com/caf/core/services"
       validating dependency to used DC "sap.com/caf/runtime/connectivity/base"
       validating dependency to used DC "sap.com/caf/runtime/connectivity"
       validating dependency to used DC "sap.com/applocking"
       validating dependency to  public part "default" of DC "sap.com/com.sap.engine.client.lib"
       validating dependency to  public part "default" of DC "sap.com/jta"
       DC model check OK
    Start build plugin:
       using build plugin: sap.com/tc/bi/bp/ejbmodule
       starting build plugin from : C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_BUILDT\DCs\sap.com\tc\bi\bp\ejbmodule\_comp\gen\default\public\ejb\
    Build Plugin 'EJBModulePlugin', Version 7.00 SP 9 (NW04S_09_REL, built on 2006-10-25 22:26:50 CEST)
       development component:  user_example/ejbmodule (sap.com)
          software component:  MyComponents (demo.sap.com)
                    location:  local
                        type:  J2EE, subtype EJBModule
               build variant:  default
             source location:  mzwrxw@w2mzwrxw01
           plugin start time:  2008-04-17 15:51:39 GMT+05:30 (IST)
                     Java VM:  Java HotSpot(TM) Client VM, 1.4.2_09-b05 (Sun Microsystems Inc.)
    General options:
      convert *.xlf to *.properties: yes
      include sources for debugging: yes
    Source folder src exists but is empty.
    Plugin initialized in 0.187 seconds
    Preparing data context..
    No 'default' JDK defined, will use running VM.
    Data context prepared in 0.078 seconds
    Executing macro file..
      Using macro file:     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_BUILDT\DCs\sap.com\tc\bi\bp\ejbmodule\_comp\gen\default\public\ejb\macros\build.vm
      Creating output file: D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\gen\default\logs\build.xml
    Macro file executed in 0.141 seconds
    Starting Ant..
      Using build file:     D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\gen\default\logs\build.xml
      Using build target:   build
      Generation folder:    D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\t\0C4E7D6DF04F4534176A82AEB939F6DA
      Using Ant version:    1.6.2
    compile:
          [echo] Starting Java compiler
          [echo] Settings:
          [echo]   debug:       on
          [echo]   optimize:    off
          [echo]   deprecation: off
          [echo]   verbose:     default
          [echo]   encoding:    UTF8
          [echo]   source:      default
          [echo]   target:      default
          [echo]   source path: D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule
          [echo]   class path:
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\tc\logging\_comp\gen\default\public\default\lib\java\logging.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\tc\logging\_comp\gen\default\public\default\lib\java\logging.perf.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_JTECHS\DCs\sap.com\tc\ddic\metamodel\content\_comp\gen\default\public\default\lib\java\SapMetamodelDictionaryContent.zip
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_JTECHS\DCs\sap.com\com.sap.jdo\_comp\gen\default\public\default\lib\java\jdo.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_JTECHS\DCs\sap.com\com.sap.jdo\_comp\gen\default\public\default\lib\java\sapjdoapi.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\jmi\_comp\gen\default\public\jmi\lib\java\sap.combimmrjmijmi.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\core\_comp\gen\default\public\default\lib\java\sap.combimmrcoredefault.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\km.proxyjava\_comp\gen\default\public\ClientApi\lib\java\sap.comcafkm.proxyjava~ClientApi.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\applocking\_comp\gen\default\public\default\lib\java\applocking.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\applocking\_comp\gen\default\public\default\lib\java\frame.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\applocking\_comp\gen\default\public\default\lib\java\jdbc.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\metamodel\_comp\gen\default\public\compilation\lib\java\sap.comcafmetamodel.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\metamodel\_comp\gen\default\public\compilation\lib\java\sap.comcafmetamodel_JMI.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\metamodel\_comp\gen\default\public\compilation\lib\java\sap.comcafmetamodel_JMI_src.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\com.sap.engine.client.lib\_comp\gen\default\public\default\lib\java\sapj2eeclient.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\runtime\connectivity\base\_comp\gen\default\public\com.sap.caf.mp.base\lib\java\sap.comcafruntimeconnectivitybase~com.sap.caf.mp.base.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\runtime\security\_comp\gen\default\public\ClientAPI\lib\java\sap.comcafruntimesecurityClientAPI.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\runtime\api\_comp\gen\default\public\compilation\lib\java\sap.comcafruntimeapicompilation.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jdbc20\_comp\gen\default\public\default\lib\java\jdbc.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\cwm_1.0_source\_comp\gen\default\public\compilation\lib\java\sap.combimmr~cwm_1.0_source.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\cwm_1.0_source\_comp\gen\default\public\compilation\lib\java\sap.combimmr~cwm_1.0_source_JMI.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\cwm_1.0_source\_comp\gen\default\public\compilation\lib\java\sap.combimmr~cwm_1.0_source_JMI_src.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\runtime\impl\_comp\gen\default\public\CAFRuntimeAPI\lib\java\sap.comcafruntimeimplCAFRuntimeAPI.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\ejb20\_comp\gen\default\public\default\lib\java\ejb20.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jms\_comp\gen\default\public\default\lib\java\jms.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\com.sap.security.api.sda\_comp\gen\default\public\default\lib\java\com.sap.security.api.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\com.sap.security.api.sda\_comp\gen\default\public\default\lib\java\com.sap.security.api.perm.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jta\_comp\gen\default\public\default\lib\java\jta.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\core\services\_comp\gen\default\public\ClientAPI\lib\java\sap.comcafcoreservicesClientAPI.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\com.sap.exception\_comp\gen\default\public\default\lib\java\exception.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\CAF\DCs\sap.com\caf\runtime\connectivity\_comp\gen\default\public\com.sap.caf.mp.core.api\lib\java\sap.comcafruntimeconnectivitycom.sap.caf.mp.core.api.jar
          [echo]     C:\Program Files\SAP\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\BI_UDI\DCs\sap.com\bi\mmr\db\_comp\gen\default\public\default\lib\java\sap.combimmrdbdefault.jar
          [echo]   output dir:  D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\t\0C4E7D6DF04F4534176A82AEB939F6DA\classes
         [javac] Compiling 23 source files to D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\t\0C4E7D6DF04F4534176A82AEB939F6DA\classes
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:51: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]         com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:81: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]             com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                   ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:92: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]             com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                   ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:96: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]         com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:105: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:115: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:126: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:131: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:139: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:154: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:159: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:165: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:186: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                    com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                                ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:200: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                    com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                                ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:206: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:213: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:233: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]             com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                   ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:244: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]             com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                   ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:254: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]         com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:261: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]         com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:270: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:281: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                  com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:288: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]          com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:295: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]         com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:300: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:308: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, new java.lang.Object[] , com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:370: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:462: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.entering(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                        ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:477: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]                com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                               ^
         [javac] D:\Documents and Settings\mzwrxw\.dtc\LocalDevelopment\DCs\sap.com\user_example\ejbmodule\_comp\ejbModule\com\sap\user_example\besrv\user\userServiceBean.java:482: cannot resolve symbol
         [javac] symbol  : variable JARM_REQUEST
         [javac] location: class java.lang.String
         [javac]           com.sap.caf.rt.util.CAFPublicLogger.exiting(user, user.JARM_REQUEST, method, userServiceBean.location, com.sap.caf.rt.util.CAFPublicLogger.LEVEL_MEDIUM);
         [javac]                                                                       ^
         [javac] 30 errors
    Ant runtime 4.984 seconds
    Ant build finished with ERRORS
    Compile failed; see the compiler error output for details.
    Error: Build stopped due to an error: Compile failed; see the compiler error output for details.
    Build plugin finished at 2008-04-17 15:51:45 GMT+05:30 (IST)
    Total build plugin runtime: 5.515 seconds
    Build finished with ERROR
    Thanks,
    Madhavi

    HI
    i used the below line of code to log the info
    com.sap.caf.rt.util.CAFPublicLogger.entering(CAF_user, WTCServiceBean.JARM_REQUEST, CAF_methodHeader, WTCServiceBean.location, CAF_parameters);
    But , can anyone suggest ,where can i seee this log msg.
    Any pointers would be highly appreciated.
    Thanks

  • Flash Builder 4.6 Mobile Project Using Blazeds & Native Extension

    Hi,
    I'm building a Flex Mobile project in FB, that uses BlazeDS to access data through a Spring Project, and also uses an ANE file to access the device's contacts.  I want to debug the application on a device connected with a USB cable, so had to set my root and output folders in Server Settings  using UNC so it can be found from my device thru my wifi network. I also have added the native extension via the Build Path and Packaging tabs.  When I debug from a desktop emulator, things launch OK and the extension correctly tells me it's not supported on the emulator. However, if I debug on the device, FB throws an exception at launch, complaining of a java null pointer exception.  The Eclipse log, in part, looks like this:
    com.adobe.flexbuilder.project.AbstractXMLModel$FileReadException: org.eclipse.core.internal.resources.ResourceException: Resource '/NewOne-debug/NewOne-app.xml' does not exist.
              at com.adobe.flexbuilder.project.air.internal.xml.ApplicationXMLModel.<init>(ApplicationXMLM odel.java:102)
              at com.adobe.flexbuilder.project.air.AppXMLCreator.init(AppXMLCreator.java:91)
              at com.adobe.flexbuilder.project.air.AppXMLCreator.<init>(AppXMLCreator.java:80)
              at com.adobe.flexbuilder.project.air.AppXMLCreator.<init>(AppXMLCreator.java:73)
              at com.adobe.flexbuilder.project.ui.utils.ANE.AppXMLFileANEExtensionHandler.getAppXMLCreator (AppXMLFileANEExtensionHandler.java:153)
              at com.adobe.flexbuilder.project.ui.utils.ANE.AppXMLFileANEExtensionHandler.retainExtensionI ds(AppXMLFileANEExtensionHandler.java:315)
              at com.adobe.flexbuilder.project.ui.utils.ANE.ANEController.modifyAppXMLforPackaging(ANECont roller.java:371)
              at com.adobe.flexbuilder.project.ui.utils.ANE.ANEController.modifyAppXMLforPackaging(ANECont roller.java:338)
              at com.adobe.flexbuilder.project.ui.utils.ANE.AbstractANEPackageHandler.modifyAppXMLforPacka ging(AbstractANEPackageHandler.java:91)
              at com.adobe.flexide.launching.multiplatform.launchhandlers.AbstractMultiPlatformLaunchHandl er.applyNativeExtensionDetails(AbstractMultiPlatformLaunchHandler.java:164)
              at com.adobe.flexide.multiplatform.android.launching.ADBLaunchHandler.doPackage(ADBLaunchHan dler.java:424)
              at com.adobe.flexide.multiplatform.android.launching.ADBLaunchHandler.launch(ADBLaunchHandle r.java:250)
              at com.adobe.flexide.launching.multiplatform.MultiPlatformLaunchDelegate.launch(MultiPlatfor mLaunchDelegate.java:191)
              at com.adobe.flexide.launching.AbstractFlexLaunchDelegate.launch(AbstractFlexLaunchDelegate. java:244)
              at com.adobe.flexide.launching.AbstractFlexLaunchDelegate.launch(AbstractFlexLaunchDelegate. java:134)
              at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:854)
              at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:703)
              at org.eclipse.debug.internal.ui.DebugUIPlugin.buildAndLaunch(DebugUIPlugin.java:928)
              at org.eclipse.debug.internal.ui.DebugUIPlugin$8.run(DebugUIPlugin.java:1132)
              at org.eclipse.core.internal.jobs.Worker.run(Worker.java:54)
    Caused by: org.eclipse.core.internal.resources.ResourceException: Resource '/NewOne-debug/NewOne-app.xml' does not exist.
              at org.eclipse.core.internal.resources.Resource.checkExists(Resource.java:320)
              at org.eclipse.core.internal.resources.Resource.checkAccessible(Resource.java:194)
              at org.eclipse.core.internal.resources.File.getContents(File.java:287)
              at org.eclipse.core.internal.resources.File.getContents(File.java:278)
              at com.adobe.flexbuilder.project.air.internal.xml.ApplicationXMLModel.<init>(ApplicationXMLM odel.java:100)
              ... 19 more
    I guess the problem is that when the application tries to run on my device, the extension is not finding the application descriptor file.  Is there anything else I need to do?
    I appreciate any help.
    Jay

    Here's the fix in case anyone else runs into this problem.  When Flash Builder is building the deployment during launch, it converts the mapped path to a mangled local path for the ane to find the descriptor to a relative path, which can't be found and throws the null pointer.  Making the Output Folder path actually local to the computer, as opposed to the default that FB creates, resolves the error, and still allows blazeds access from the device.

Maybe you are looking for

  • How can I sort all files and folders by size?

    Due to lack of space I need to find the biggest files and folders on my Mac OSX Mountain Lion, but "Size" is not in the Find options. And I don't know the wildcard to sort all files and folders by size in Easyfind. Thanks Sarah

  • Line of copy at top of photo in burned dvd at intervals.

    I did a slide show in Iphoto.  Added some text slides for birthdays.   The I shared to IDVD and after reviewing the settings burned the DVD. I get the following line at the top of the first slide and it pops up periodically during the slide show on t

  • IE 11 on Windows 7 x64 does not display FeedBurner feeds correctly

    Dear All, I have just installed Internet Explorer 11 on my Windows 7 x64 system. It all went smoothly except for certain feeds not displaying correctly. After a bit of investigation it seems FeedBurner feeds are the ones which do not work. Any of the

  • Cancellation of debit memo process

    Hi all, Can someone share with me on the process for the scenario whereby duplicate debit memo have been posted and my user wish to reverse the duplicate debit memo billing document? Is cancelling the debit memo billing doc the correct process? My us

  • Font management with InDesign and Windows 7

    Hello I am presently looking to upgrade to Windows 7 and use InDesign CS4.  I have had a play with installing postscript type 1 fonts using the windows font manager and it seems absoloutley average, but it worked (I think).  I was wondering if you ha