Bulk adding IP Phones in Call Manager 5.1

Does anyone have experience adding end users in Bulk to Call Manager 5.1? If so can you show me the CSV file format for this? We will be adding over three hundred new IP phones to our call manager and we have all the Mac addresses already, we just need to create all of the phones and directory numbers in Call Manager.
Any guidance would be great.
Thank you.
Rgds,
Vicky

Hello and thank you for your post. Unfortunately I have only just now had a chance to look at your post. Can you please renew my access to this download??
Please get back to me. Thank you again.
Rgds,
Vicky

Similar Messages

  • Reboot phone thru Call Manager

    How do you reboot a phone thru Call Manager?
    I have to reboot some phones afterhours and need to do it remotely.

    find the phone in the callmanager (Device > Phone), and click Reset

  • Cdr doesn't bill Cisco phone 6901 Call Manager release 9

    Hello Engineers,
    Actually I opened a TAC for a problem that I got in my customer's environment.
    I have CUCM release 9 and Cisco phone 6901 - firmware: SCCP6901.9-3-2.loads
    When I tried to see the calls from CAR I didn't get output from the CAR/CDR.
    I did an upload to the firmware SCCP6901.9-3-1-SR1-3.loads.
    After that all calls were ok.
    I hope this post can help anothers engineers

    Hi Karina,
    Thanks for taking time out of your busy schedule to help others
    here @ CSC Much appreciated!
    Cheers!
    Rob
    "Seek it out and ye shall find  " 
    - OneRepublic

  • What is the best cisco ip phone for call manager and ipcc practicals

                       Hi i have recently started my training on Cisco Call Manger and CCIE voice from a leading cisco voice training institute (http://networkerszone.com/), and am working on 7900 series phones, is there any other phone that i should use or this is fine.

    Naval,
    7900 phones are good enough for both CUCM & UCCE. UCCE however doesnt support all models of 7900 series, please refer UCCE Compatibility Matrix for supported phone models.
    You may also use CIPC as agent phone.
    GP.
    Pls rate the post if it helps !!

  • Factory Default from Call Manager

    I have a client which is private. They have many type phones that we need to change with new one. I want erase all information like call history, Itl files, tftp servers etc.
    My first question is : What can I do to delete all these kind of information. My first idea is factory default? Can we make differently? 
    Second question is : If we can success that with anyone's answer , Can we send this command to all 7841 ip phones from Call Manager 10.5.1?
    Second question is important part of work. We must do approximately 500 phones which I need to change with new phones. I want to send this command from Call Manager?
    Regards..

    Just go the phones erase call history/network config/ITL files etc the settings you need to delete. I dont think there will be a bulk way to do some of the items.
    But If you must erase everything from the phone, you will need to reset the phone to factory defaults.
    There is no easy/bulk/remote way to factory reset the phones. You will need to do it from the phones itself by pressing the sequence of keys.
    Still only possible way would be to setup a DEMO cucm and connect the CUCM/phones to an isolated 24/48 port switch/switches. Factory reset them and let them download the new firmware files from the demo system.
    They will still have TFTP server defined in the end (of the DEMO server) and without which you cant get the phone to download the firmware.
    -Terry
    Please rate all helpful posts

  • Cisco Call manager 7.2 through ASA firewall

    Hi,
    We have a part of our building that we have sold to another company. We still have to provide them with some resources until they can install their own network. We have a 6500 switch there and we are going to implement a ASA in between and lock down most communication. One of the resources required are  Cisco IP phones. 
    Does anyone know which ports etc are required to be opened to allow communication between these phones and  Call manager and other IP phones on the site?
    Any help would be appreciated             

    Hi Andrew
    The attached document may assist:
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/port/7_0/CCM_7.0PortList.pdf
    A lot depends on topology etc, and the handset registration protocol you are using (SIP vs SCCP).
    Hope this helps.
    Barry Hesk
    Intrinsic Network Solutions

  • Licensing with Call Manager 5.0

    Hi,
    can you help me with licensing IP phones on Call Manager 5.0?
    I can take server with CallManager sofware and I don't need any license.
    Otherwise, I can take this product:
    LIC-CM-DL-10= CallManager Device License - 10 units
    I 5.0 version every phone have number of units. So, does it mean, that I can take one 7940G (which have 4 units) and after that I still have 6 units. Next time, if I take one more 7940G, I don't need to take any more licenses. Am I right?
    Thanks a lot,
    Vlaho

    Hi Vlaho,
    This shouldn't be too bad. Once you have recieved the License file, here is the method to Upload it to CCM 5.0;
    Uploading a License file
    Use the following procedure to upload a license file to the Cisco Unified CallManager server with the matching MAC address that is provided when requesting for a license file.The Cisco Unified CallManager server where the license file is loaded takes on the functionality of the license manager.
    Note Upload the license file only on the first node of Cisco Unified CallManager cluster.
    Procedure
    Step 1 Choose System > License > Upload License File.
    The License File Upload window displays.
    Step 2 The Existing License Files drop-down list box displays the license files that are already uploaded to the server.
    Note Click View File to view the file content of any existing files.
    Step 3 To choose a new license file to upload, click Upload License File.
    The Upload File pop-up window displays.
    Step 4 Browse and choose a license file to upload to the server.
    Step 5 Click Upload License File.
    After the upload process is complete, the Upload Result file displays.
    Step 6 Click Close.
    Step 7 In the License File Upload window, the status of the uploaded file displays.
    From this doc;
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a0080633230.html#wp1049590
    Hope this helps! And best of luck with your install!
    Rob

  • 7975 firmware for call manager express

    i would like to add 7975 phone to call manager express.
    where do I get the firmware for 7975 for cme?
    i tried from software.cisco.com but it's for call manager only.

    Hi pranavluhar,
     check this link cme-153-3Mv2.rar (in 10.0 option).There is a 7975 version for CUCME.
    Hope this helps.

  • Cisco ip phone 7960 cannot connect to call manager express

    The 7960 ip phone seems not to connect to the call manager express
    router and i have already put the firmware and configured the tftp
    server,the rest of the phones the 7911`s are all working ok,i have tried
    to reset the phone but it doesnt respond to the # key so as to reset to
    factory defaults.
    I have tried all the options of resetting it but to no avail.
    could someone give me some techie tips on this ? could it be a hardware issue ?? please assist.

    Go to the phone and check if the TFTP server is correct (should be the CME IP address). Also check the DHCP address.
    Resetting 7900 Series IP Phones to Factory Defaults:
    http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtml
    Check the bug:
    CSCed93627: Not able to reset 7970 back to factory defaults

  • Call Manager, Tandberg Video Phone bandwidth

    We have recently rolled out a Tnadberg Video Phone.
    Is the Tandberg phone considered an endpoint in call manager?
    Can you adjust what bandwidth the phone uses from within call manager?

    Locations in Cisco Unified CallManager Administration specify how much audio and video bandwidth is allowed for all calls in a specific location.

  • Cisco call manager and ip phone software.

    Hi everybody.
    Does Cisco call manager also include software required for ip phone? Or software for ip phone needs to be installed on tftp server and it does not come with cisco call manager.?
    thanks and have a great weekend.

    Hi Sarah,
    by ip phone software, do you mean Cisco IP Phone Agent software?
    if  yes, then you need to have Customer Response Solution (CRS) and Call Manager together to setup ip phone software (services).
    check this link for further info:
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a00801c5765.shtml
    plz Rate if it helped.
    Soroush.

  • I am currently in Cameroon, Africa and after arriving here, I added Global services to my plan in hopes to be able to use my phone to call local numbers.  When I dial local numbers in Cameroon, with or without the country code, the call fails.  I suspect

    I am currently in Cameroon, Africa and after arriving here, I added Global services to my plan in hopes to be able to use my phone to call local numbers.  When I dial local numbers in Cameroon, with or without the country code, the call fails.  I suspect it may be that the phone is 3G and this area only supports 2G.  Help!

    cctga,
    We appreciate you taking the time to reach out to us. I am sorry to hear that you are having trouble while traveling. We definitely want to make sure you have all available options. Normally when traveling internationally we reccommend setting up international services prior to leaving. When you added the services did you do so online or with a rep? It would be best to contact our global department in order to troubleshoot any and all issues with services while international http://vz.to/17KseUf.
    Thank you,
    TonyG_VZW
    Follow us on Twitter @VZWSupport

  • Phones getting unregistered frequently from call Manager

    Hi
    We have Call manager in our HQ and some phones in Branch in a different country. From CUCM there is a SIP trunk towards router in branch.
    Users in branch occassionally complain of phones getting unregistered.HQ and branch are connected through internet with suffiecient BQ 14 Mbps on each side.
    Thanks for helping me out.
    Regards
    Vibha

    Hi Vibha,
    You can check the Phone status messages to start with and also check the app / syslogs on the cucm corresponding to the time stamp when they are unregistered to see the reason code for the unregistered event. However, a packet capture would be ideal to check what exactly is causing the issue as we can see which packets are exchanged or getting dropped between cucm and IP phone.
    HTH
    Manish

  • Call Manager Phone Services to Personal Address Book

    Cisco Forum:
    I'm trying to configure Call Manager (8.6.2.x) for Phone Services so that we can use the IP Phone's Service button to access the Personal Address Book & Fast Dials.  While I have the option (Test PAB-Fast Dial) appearing when the Services button is selected, the process ends with the bottom screen shot showing "Error in Authentication."
    By using the Directories button then selecting the Personal Address Book, I can successfully log into the application.
    What am I missing?  Below is the current URL being used.
    Thank you.
    Dan
    http://10.2.5.234:8080/ccmpd/login.do?name=#DEVICENAME#&service=pab

    Nelson:
    The URL that is working for us is: 
    http://10.2.5.234:8080/ccmpd/pdCheckLogin.do?name=#DEVICENAME#&service=pab
    then use your own IP address for the Call Manager node.
    Our Call Manager configuration is shown below.
    To access the feature, we hit the Services Button, are prompted with a Personal Address Book option, select it, then are promoted for a UserID/PIN (shown further below), at which point I enter my LDAP ID and a PIN.  The PIN is created in Call Manager under User Management ==> End User ==> PIN.
    Good luck with your process.
    Dan

  • Call manager and Cisco IP phones

    I would like to know if it's possible to use Cisco IP phones in small environments, without having Call manager, or it's mandatory to have always CallManager if one wants to use the IP phones.
    Thank you

    You can use Call Manager Express, which runs on cisco 1751/60, 2600 and above routers. it can support up to 120 users. Cisco Unity Express will provide voice mail. this is a network module in 2600 and above routers. for more info, see www.cisco.com/go/ccme

Maybe you are looking for

  • Ajuda com Iphone 3GS IOs 5.01

    Prezados,  Preciso de uma ajuda urgente...   Tenho um Iphone 3GS com IOs 5.01 que trava a todo momento e desliga sozinho. Não sei mais o que fazer, poderiam me ajudar? Obrigada Poliana

  • RAM Upgrade on Satellite L30-11D

    My brother has a Satellite L30-11D and he has bought an additional 2GB RAM to upgrade from 512MB. HE has sent me an email - extract below, but does not get regular access to Internet and therefore no time to post this. My laptop had 512 MB ram and I

  • Help!! adding new pages to doc with logo!!!

    I've posted various questions for a couple hours now, none are answered.  Is everyone sleeping or does no one know how to use Pages??  I'm near tears and I've read the manual about 10 times and don't understand it.  I've tried to Google it but I'm no

  • XML file Synchronization

    Hi All, I have created an XML file from a table in oracle. Now, the requirement is, to update the file as soon as any DML occurs in the respective table. Does anyone have an idea how to implement it?? One way culd b to create trigger on the possible

  • Calling form with value problem

    Hello All, Platform: forms 6i calling form- quot.fmx called form- inv.fmx Value to pass: ref_no on Calling form-> button-> when-button-pressed-trigger DECLARE P PARAMlist; BEGIN P:= CREATE_PARAMETER_LIST('ABC'); ADD_PARAMETER(P,'A_REF_NO',TEXT_PARAME