Burn from dvd studio pro, to playing on MBP?

I just got done making a dvd on DVD studio pro and the dvd plays perfectly fine on my two dvd players that I have at home. But When I want to play it on my Mac book pro, my computer just tries to read it and then spits it back out. any help? why is it not playing on my MBP?

Hi
It's the same machine where you burned the disc? I would try using a different media brand. But ussually the playback problems are in stand alone players, not in computers.
Did you try another video DVD in the same machine?
Hope that helps !
Alberto

Similar Messages

Blurry Text from DVD Studio Pro

Hello, I've created 4 'slide show' type presentations in motion 2. Project settings are:
Width: 1360
Height: 768
Bit Depth: 8 Bit
Pixel Aspect Ratio: HD (960x720, 1440x1080) 1.33
Field Order: None
Frame Rate:59.94 fps
Render Settings:
Motion Blur: Samples: 8
Shutter Angle: 360
Output: Antialiasing Method: Best
I've tried many many compression settings:
MPEG-2 6.2Mbps 2-pass 16/9.m2v
Uncompressed 10-bit NTSC.mov
Importing raw motion files into DVD Studio Pro
All of the resulting dvds burned from DVD Studio pro look pixelated and blurry when played on a dvd player onto a Toshiba 32HL86. Unfortunately its an SD dvd player connectedt to the tv, so not sure if that has a major impace.
DVD Studio Pro Settings are:
Project: SD DVD
Video Standard: NTSC
General:
SD DVD Menus, Tracks and Slideshows:
Display Mode: 16:9 Letterbox
Encoding:
MPEG-2-SD
Aspect Ratio: 16:9
Field Order: Auto
Mode: One PAss VBR
Bit Rate: 6.8
Max Bit Rate: 8.0
Motiion Estimation: Best
I am at my wits end, can somebody tell me what I'm doing wrong?

I'm not an expert, but have recently had similar problems with graphics that had text, black lines, lots of contrast, and movement. They looked great on HD but when I made a SD DVD, they were very blocky and pixellated - completely unusable. After lots of experimentation, I've finally got an acceptable dvd. Went back to my original shots - in Final Cut, (I'm not sure if you can do this in Motion) and carefully applied a little Gaussian Blur (.25 to1) to each according to how badly they pixellated. Also adjusted blacks and whites so they weren't so contrasty. Then made my mpeg with Compressor - two pass vbr, 6.8 mbps, best motion estimator. The Gaussian Blur seems to break up the areas that get blocked up and pixelated. SD dvd is such a lousy low resolution medium anyway, that it doesn't seem to result in any focus problems and helped most shots - I've even gone back and applied it to some of the regular footage that was pixellating. It was a lot of work, you may want to see if an expert weighs in on this.

DVD is Not Burning in DVD Studio Pro

DVD is Not Burning in DVD Studio Pro 4.2.0

I used build and format approach. Both discs play fine on computer platforms, but not on a consumer DVD connected to the TV. Normally I have no problem. I checked and rechecked several times all the preferences for Studio Pro. The only thing I noticed was instead of generating a Video and Audio TS file, it generated one HVDVD_TS file. Is this the issue? If so,where do I correct this (in the settings)?
Thanks

Exporting Subtitle from DVD Studio Pro

Is there a way to export subtitles from DVD Studio Pro or Is there a tool somewhere that will generate an STL file from a DVD Studio Pro subtitle stream?
Thanks for your help!

Yes, other than the manual -- which I have exhausted. It gave me the coding for a text-based caption, and the coding for a graphic, but not the coding that would put both on the same clip (same time value).
However, I can manually go into the subtitle inspector and add whatever element (the text or the graphic) each with its own offsets, and have them appear flawlessly together. I am convinced there must be coding that generates this effect I can use in the STL file, but I have found nothing on the web, nor any of several downloaded manuals (including pp. 456 - 460).
Any advice?

How to export MPEG2 from DVD Studio Pro with subtitles?

Does anyone know how to export MPEG2 from DVD Studio Pro with subtitles?

You cant do that...
We might be able to help you more if you are trying to do something specific,
-Jake

DVD Studio Pro not playing back audio of asset converted from FCP via compressor.

I exported project via compressor:
File Extension: m2v
Estimated file size: 4.34 GB
Video Encoder
    Format: M2V
    Width: 720
    Height: 480
    Pixel aspect ratio: NTSC CCIR 601/DV
    Crop: None
    Frame rate: 29.97
    Frame Controls: Off
    Aspect ratio: 4:3
    Field dominance: Bottom first
    Average data rate: 3.6 (Mbps)
    2 Pass VBR enabled
        Maximum data rate: 7.5 (Mbps)
    High quality
    Best motion estimation
    Closed GOP Size: 15, Structure: IBBP
    DVD Studio Pro meta-data enabled
This took about 7.5 hours. I exported the audio separately as AC3. Finder plays it sound & pictures. Quicktime plays the video. DVD Studio Pro, when I drag the assets (video, audio) to the timeline editor, so I can play it in the viewer, it plays the audio the video is black. No setting in view or any other setting will get it to play the video. This project is due to ship today and I don't want to re import it if I don't have to.
I exported this project before the MPEG2 export as a Qicktime with .mov suffix. This plays alright, but there is artifacting around motion. I think this is due to low VBR, but don't know. Can ayone help?
Dix Moser
[email protected]
FCP Studio
PowerMac 1.8G 3G mem 250G HD
750 G ext. Firewire drive (where media is stored)

If I may chime in...
I'm a little confused on the "what plays what" part, but all that really matters is what DVDSP sees/plays.
I've worked on a system like yours and what I'd recommend is:
1. NEVER export via Compressor. It's just ungodly slow on anything less than a Quad. Export a self contained QuickTime Movie using the first export option and use that to feed Compressor.
2. Segment your output into manageable clips (I like 15-20 minutes) both to perfect the encoding and so you aren't re-encoding the whole show if something goes sour. It will all play fine as long as it's all in the same DVDSP timeline.
From what you describe, I'm thinking you're on an early version of Compressor that had A-Pack as the AC-3 encoder. This is no biggie, I mention it mostly to verify. Early Compressor was good too.
Make maybe a 5 minute piece to tune up. Just export as normal, then into Compressor. Your encoding values seem about right. Get the AV pair into DVDSP and it should play. I'm guessing that part of your problem is that the processor is fighting to handle the project size. Build the test clip project and look at it in DVD Player to view what would have been burned. If all looks OK, go for it. If not, bring back the results for discussion. This should be a snap, it's just a really big project. Keep your head up, I had a friend do a 225-minute disk on his G5...

Error burning to LaCie drive from DVD Studio Pro 3...

Whenever I attempt to burn a DVD to my LaCie d2 DVD+-R drive, using DVD Studio Pro 3, I get an 'error #6' and the burn is unsuccessful. At the 'formatting' stage the process hangs up after a couple of minutes and returns an error message with the following text:
"The recording device reported error #6: Power on, reset, or bus device reset occurred. (0x29, 0x00.)"
Has anyone else experienced this? I have used both DVD+R and DVD-R discs. I have used the device on two different G4s--a 733MHz, and a dual-1.25GHz. I have worked with the source files on the hard drive, as well as on an external drive. The size of the project is nowhere near capacity for a DVD.
But the result is always the same: Burn aborted, 'error #6.' I'm at my wit's end. Thanks for any suggestions or insight...

hey terry
you say you are directly burning from DVDSP to your lacie drive, correct? is it an internal drive? did you recently replace your drive?
if it is, go to "about your mac" on finder and click on "more information".
look at your ATA and or "burner" (something to that effect) and make sure that is "vendor supported" because if it is not, iTunes, DVDSP and iDVD will have problems burning media directly from those apps.
the easiest way to fix this is with "patchburn". it will make your drive compatible or "supported" by able and you will have NO problems buring.
question: do you have another burning program (such as toast)? do you have problems burning from the finder?

Aspect ratio problem in Windows Media Player for DVD from DVD Studio Pro

So I made a DVD with DVD Studio Pro and it looks good in Apple's DVD Player, on an Insignia DVD player appliance and on Playstation 2. Both the movie and the deleted scene were 16:9 from camera to Final Cut Pro and they show that way in all these players.
But on Windows Media Player for Windows XP, the program thinks the movie is 4:3 and the deleted scene is 16:9. Nero's Showtime has the same exact behavior, but at least you can force aspect ratio on Nero.
Besides being longer, the movie is different from the deleted scene in that the movie was originally out of Final Cut Express on an older Mac and it was encoded big endian. The deleted scene was output from Final Cut Pro and encoded little endian. I didn't think it would make a difference, but I tried outputting the movie from Final Cut Pro on the newer Mac and it did come out little endian. I took that into DVD Studio Pro, got rid of the old VIDEO_TS folder and re-built the project, burnt a new DVD. Then I went back to Windows and...
...the same exact problem. Some of the people I give this DVD to will be using Windows Media Player to view it, which is why I want this to not be an issue at all. What am I overlooking?

Look, everyone here (who each have been creating DVDs for over a decade) is telling you the same story. WMP is buggy. Everyone in the industry knows that. Hardware manufacturers like Dell and HP, know that. Why don't you use the DVD player program that they put on the hard drive? Sure one "Hollywood" title works. Did I mention that WMP is buggy? Test a thousand titles, and I'm certain that you will find some discs have problems on WMP, and WMP alone. (And it isn't my assertion that Hollywood DVDs have issues in WMP, everyone is telling you that.) No one has a solution for this, except to not use WMP. Let me repeat once again, no one has a solution for this except to not use WMP. It is impossible to add any sort of programming to the disc that will detect which player is being used to play the disc and compensate for the problems of that player.
Let me put it this way, if you have a disc that plays fine on Zeus's device, and on Apollo's device, and on Hera's device, and on Hermes' device, and on Artemis' device, but you have problems with Athena's device, then logically, Athena's device has a problem... not the disc. Your own experience has proved this to be true. If you were having problems with every device used, THEN you could rightfully say that there is a problem with the disc.

Poor image quailty from DVD Studio Pro

Hello,
I produced a 17minute DVD a few years ago, shot SD with a Panasonic DVX 100a. Edited in Final Cut Pro 6. They have asked me to burn a couple more DVD's for them. When I imported the assets 2 pass M2v & ac3 audio and burned the DVD with a bit rate of 6.5 to 7. the image quality is really low. I previously ran all FCP through Compressor, Highest quality, best etc.
Someone told me that going back to FCP and using a de-interlacing filter applied to the project would help with image quality.
Can anyone point me in the right direction? I know that going to a DVD will never look as good as my sweet 27" monitor, but the image seems blown out (hot) and the colors unsaturated and a bit too grainy. It seems more so then I remember the project looking. I am using DVD Studio 4.
So is there any steps that can help me have a SD project edited in Final Cut Pro 6... use Compressor... 2 pass highest quailty 90 min DVD... to DVD Studio Pro 4 and get the best quality I can get. I appreciate any guidance you can give me.
Thanks,
Jan

You may find that Photoshop does a better job of resampling down to your SD PAL resolution. When DVDSP resamples down from your 1024x576 file, you are at the mercy of the hardware or software rendering in DVDSP, depending on your DVDSP prefs. Ideally, I'd work in Photoshop at 720x576, and use the pixel aspect ratio correction to correct the preview aspect ratio in Photoshop.

Slight pixellation on faces at end of DVD after burning in DVD Studio Pro. Can you help?

I am appealing to those much more expert than myself. I have burned a DVD of my short film in DVD Studio Pro.
Original file: Apple Pro Res 422 HQ (PAL 25fps)
I put this into Compressor: Best quality DVD 90 mins.
Then I imported this in DVD Studio Pro and burned a DVD
The DVD looks great until the end where the faces start to go pixellated in an outdoor scene every second or so for a second.
The thing is that this only suddenly started to happen. I had originally done the compression and burned dvds and it all looked fine, but then suddenly when I burned some extra DVDs I noticed this had happened. I recompressed the files, and it had the same problem in exactly the same place. (The original file doesn't have this problem.)
The thing is that in between I had made a new separate DVD Studio Pro project in NTSC and imported my compressed 29.97fps Apple pro res file of the film. I'm not sure how this would have affected the original PAL project or if this has anything to do with it!
When I originally burned the PAL DVDs I also did a second version where I exported from FCP a PAL QT of the film 720x576 and then imported this into DVD Studio Pro and let DVD Studio Pro do the rest of the compression. I am trying this again to see if this makes any difference.
Any advice?

Hi Christina, thanks for this. I am a bit confused exactly how many and where to put.
You see the shot in question is a static two shot. It is used several times in the scene, but the only place I have a problem is the final time we see the shot. It is at the end of the shot and over the final 13 seconds, the faces pixellate slightly every now and then for like a frame. How many compression markers should I put in do you think?
Thanks again for your help.

DVD studio pro not playing entire video

When I use the simulator it only plays a portion of the video, and when I burn it to a DVD it stops at the same point. But both the audio and mpeg2 in the track play all the way through though. What am I doing wrong?

deadbeatpanda wrote:
So if the project is corrupt, does that mean I just have to re export my project in FCP? I used quicktime conversion and I read that it isn't recommended for exporting to be burned to DVD. I orginally tried to use compressor to get it to mpeg2 for DVD studio and what not so I compressed it again and the same thing happened. I also tried to use the share option in FCP with the DVD option but it exported for over 10 hours and was stuck at 5 minutes remaining for about the last 3 hours so I just cancelled it. This is the first time I have ever had to burn to DVD so sorry for being such a noob. And I have no menu, the DVD just needs to play automatically.
No, the clips do not automatically need to be re-exported. The issue with QuickTime is primarily a quality issue.
As Michael mentions above, the preferred workflow is "File: Export: Quicktime movie (NOT quicktime conversion) with current settings. Take this file into compressor and apply the appropriate dvd preset."
I like to think of the export as a "master" file that I use as a basis for transcoding.
I have little knowledge of the newer output options like Sharing. My experience has been that the things done to "simplify" the work usually compromise quality and frequently don't work well.
Here's an article on making an autp-play DVD:
DVD Studio Pro: Authoring a DVD that plays automatically without a menu

Output Audio from DVD Studio Pro works on some DVD's but not others

Hello All,
Would really appreciate any help here.
My project in final cut pro 6 has audio and it plays fine on the computer as well as the dvd studio pro simulator. I send the final cut pro file to compressor and then to dvdsp to burn. Everything works fine except when I play it in some dvd players I get no sound. I have another dvd player that plays everything with no problem. This is a big problem as I can't determine what kind of player a client has.
Is there something I need to fix in final cut pro, compressor or dvdsp?
Thanks a bunch in advance for any help anyone can provide.
Please help. Thanks

Hi
What audio format did you use: AIFF or AC3?
Alberto

DVD burner and DVD Studio Pro

Are the Mac Pros and the other intel macs have better compatibility with authoring DVDs than the G4s? I'm on my dual 867 mhz G4, and when I encode using compressor with the default setting, and build it in DVD Studio Pro, the dvd plays fine on my sony player but not on some other DVD players like JVC. My friends JVC recorer is new, they just got it a month ago, and it says it plays DVD/R discs. I produced a 7 minute short, and even with the short film, it still has problems playing on some dvd players.

I've cleaned it using disc cleaner and I've also burned the video_ts files to my sony DVD burner (my sony DVD burner is only 3 months old) besides the burner in my Mac and I'm still having playback issues on some DVD players? I've also tested them without dvd lables on verbatim discs. So no one else is having any problems authoring their DVDs on the Mac Pros or the other intel based macs?

DVD studio pro not play my project in dvd player

when burn my project in dvd studio pro in my dvd player apear " No File"
i can see my video. help me please

without knowing more info...
- Make sure your not burning a HD DVD (not to be confused with BluRay, which DVDStudioPro will not make)
- What format is your source video and audio?
- Did you set "First Play" to eitehr a track or a Menu?
- Could also be bad DVDs...

Burn in DVD Studio Pro only says Video Bitrate too high

My camera is a Sony Ex1 and I have a 1 hour and 7 minute video that I have sent through Compressor to DVD Studio Pro, which I have done many times before upgrading to FCP 7, and now when I try to build it, it always tells be that the video bitrate is to high. I have gone though preferences and reduced the bitrate to 3 and max 5 and it still does it. I have also made a Quicktime movie and tried to build and burn it in DVD Studio Pro and that does not work either. I have no problem viewing it in DVD Studio Pro when I simulate it.
I would appreciate any help you guy could give me. This is just a hobby, but I have been doing it for over 5 years and have never had this problem.

Dexil Rold wrote:
When I got DVD Pro 7, I installed 10.6 on a new 1 Tb hard drive and then installed DVD Pro 7, so it was installed on a completely new drive. When I ran my movie through Compressor, I did it two times. One with the DVD 90 Best, one with a suggestion by the new book on Studio Pro 4 (average 4.5 Mbps, Max 7.5 Mbps. I also made a Quicktime Movie. I did have to try several times to get it through Compressor, after hours FCP would quit before it was finished, but I did get it to work
It could be spiking with the 7.5, doubtful, but could be even with AC3 audio.
Try this to see if it works - Export the Final Cut movie as self contained movie (is that what the QuickTime Movie was, the entire timeline self contained?) Sorry I am a bit unclear as to whether you got that to go through Compressor or was it the timeline from FCP, which quit, but successfully went through Compressor. Perhaps it is related to Snow Leopard.
When you look at the build files on your hard drive, is it crashing out at the same point?
Take a look here http://dvdstepbystep.com/vts.php at the image at the bottom, does the build get to the same spot and/or does it throw the error in the log at the same part? Anything else in the log?
Anyway, there would be a few things to try.
I would think the easiest is to
1.) Export a small section of the movie from Final Cut as a self contained movie.
2.) Bring that movie into Compressor and run Compressor on it (including AC3 files) then bring that into DVD SP to see if it builds.
If it does, it would seem to be that there may be a spike causing the error (are you using multiple video streams, subtitles or anything else or is is a straight one video/one audio on the track.)
If that works it would seem to be a spike issue, especially if the error is thrown at the some spot in the building process.
If it gets past that, export the entire timeline and run it through Compressor and see if that works, dial down the top bitrate a bit for the video.
You could also do some other things (make another partition for an install of Leopard, not Snow Leopard, try a new user, etc.) but the above may be the easiest to start with.
When you say it takes hours to send from Final Cut, is that sending from Final Cut to Compressor or Final Cut to a self contained movie? Of course alot of this depends on your Final Cut timeline, codecs, color corrections, renders and the rest, but on a Octo it should not be painfully long for a 1 hour few minutes movie. I ave Final Cut 7 on a laptop and it does a pretty good job speedwise on some HDV timelines, which are a pain to send out. You may want to check things like where you set your scratch disks, when you are putting the media etc. (More as an aside FYI)

Burn from dvd studio pro, to playing on MBP?

Similar Messages

Maybe you are looking for