Burning discs over a network not working.

I have been burning DVDs successfully over an ethernet network for sometime (two years) but ever since I switched my attached storage to a Thunderbolt drive I have burn failures. I am suspecting that the network is not staying connected for the time needed for a succesful burn. This happens irrespective of the media or the disc burner. I used a Toshiba external and then tried a Samsung BluRay external. Both have the same problem.
I am using a mini 2.23 GHZ Intel with 8GB RAM.
The attached storage is attached to an iMac 27" late 2012 via Thunderbolt. The Mini is running 10.6.8 and the iMac is running 10.8.5.
Gigabit Ethernet network with static IPs Linksys router.
Any suggestions?

Hi,
Before going further, please make sure there is no 3rd party application that would modify/manage the network settings.
Please follow the steps below to check the network services:
1. Open the Start Menu
2. Type services in the Start Search area and press Enter
3. Click on Continue in the UAC prompt
4. Locate Network Connections, Network List Service,
Network Location Awareness, and
Network Store Interface Service
5. Verify that Status is set to Started and Startup Type is set to Automatic
6. If this is not the case then right click the service and select Start to start the service
7. Right click the service and select Properties and change the Startup type to Automatic
8. Repeat as necessary for the services listed in step 4
Hope this may help
Best regards
Michael Shao
TechNet Community Support

Similar Messages

I have inserted a disc in my remote disc and it is not working and even i am trying to eject the disc but it is not working ? what to do ?

i have inserted a disc in my remote disc and it is not working and even i am trying to eject the disc but it is not working ? what to do ?

Would you rather upgrade to windows 8, BlackBerry or Android phones? Do you honestly think those don't have problems?
You waited a lot and chose to buy an early production model. Mistakes happen all the time a factory retools and workers relearn new skills necessary to keep US happy.
Exercise your rights.... Send it back for a new one.
In any case, I feel your frustration. Btw, I love Apple but use a Blackberry

Can I restore my system from install discs when DVD is not working?

Can I restore my system from install discs when DVD is not working?
There is a disc jammed in the drive and when I try to do an install in Target Firewire mode using a G5 Tower I get an error saying the software cannot be installed on this machine, before I can even select the iMac's drive. I'm using the grey software install discs that came with the iMac.
Is my only option to open up the iMac and get the jammed disc out?
Thanks

Problem solved - I posted on the general Tiger Discussions as well.
I had the wrong machine started in Target Firewire mode.
http://discussions.apple.com/thread.jspa?threadID=2180754&tstart=0

MacBook Air wifi internet shared network not working on tethered android phone GT B5122

MacBook Air wifi internet shared network not working on tethered android phone GT B5122
I have created a password protected wifi internet network on my Macbook air. I tethered by Andriod phone onto this network, but the internet connection works intermittently on the phone, and when it stops working the network continues to show as connected to the shared network mostly(other times it keeps renewing the wifi IP address on the Andriod phone).
Also the network the MBA is connected to, is a hardwired one using a SSH login account in a student accomadations.
I am not sure, but all the restarting and refreshing of system, phone and wifi sharing and re-enabling wifi is not reparing the internet connecting on the wifi network for the phone
Really puzzled, if this is one of the Apple, Andriod compatability issues.
Cheers,
Vivek

Spanners91 wrote:
Hi.
I'm having trouble with the wireless connection on my new home hub 3. Most devices will connect easily, but there are three devices that have trouble connecting. These are an Android Phone (Samsung Galaxy Mini), an android tablet (Sony Tablet S) and an iPod. All of these devices work perfectly on other network connections, and other devices in the house are quite happy connecting to the network.
The Androids can see the network, and will try to connect to it, but when they do they just go through a loop of "connecting">>"acquiring IP address">>"disconnected". I have tried resetting the Home Hub with a pin, and that lets the devices connect for about 24 hours, but after that time they stop connecting again.
I'm really not sure what to do to fix the problem, so I will very much appreciate some help.
Many Thanks.
My lads SGMini connects perfectly to our hub3
Have you installed the BTFon app to these devices?
If so, you could delete it and then see what hapens.....
-+-No longer a forum member-+-

ACS V 4.1.1 build 23 Password Aging over SSH does not work.

Hi, my name is Elias and I have problems with ACS Password Aging over SSH does not work and there is no password aging meseges sent by ACS to de console when I use SSH. I know that there is problems with this but I can't find any workaround or documentation that says that there is no workaroun. Can you help me with this??
King Regards.

Hey Elias,
SSHv1 does not support password changes as you can do in telnet. You will need to be
running a version of IOS that supports SSHv2.
The following site explains what versions support this:
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps5207/products_feat
ure_guide09186a00802045dc.html
Rgds,
somishra

I recently tried to burn some photos to a disc. It did not work, but then I ended up with a .fpbf folder on my desktop. Can't trash it, and when trying to burn again, I get this "... can't be burned because the original items can't be found". Help???

I recently tried to burn some photos on a CD. For some reason, It did not work. Now I have a .fpbf folder on my desktop. I can't seem to get rid of it. I tried dragging it to the trash, but then I get a box asking my to type my password it, so Finder can make the changes. Doing so, does nothing at all. And when I try to burn another CD from the same .fpbf file, I get a the following message: "There are 35 items that can’t be burned because the original items can’t be found. Skip the items and continue burning?". When I skip and continue burning, nothing shows up on the CD. In the meantime, the .fpbf folder is still in my desktop. I tried changing the aliases on each pic, but it still doesn't work. Any ideas of how I can remove this folder from my desktop?
Thank you.

Beavis2084,
Thank you for your detailed explanation but something is seriously wrong with my computer. Although the method you have described is very similar to the one I tried in step 2 from my second post, I have since "done things" which may have complicated matters—or suggests that my computer has a more serious problem.
Here's what I did:
1). Installed Onyx and discovered that I had a .plist file (com.apple.iphotomosaic.plist) that was causing a Syntax error: "Conversion of data failed. The file is not UTF-8, or in the encoding specified in XML header, if XML." After doing some research online, I was given the understanding that downloading the iLife update 9.0.3 (I installed the more recent version, 9.0.4) would solve this problem because it would also fix some system issues. So, I downloaded it...and when it didn't solve the problem, I decided to just deleted that .plist file.
2). I read your knew post and decided to follow your directions, even though I realized they were basically the same steps I followed in the 2nd method I mentioned earlier. I say "basically" because, for some reason, after inserting a blank disc, my computer does not open the disc in the Finder. Instead, it places the blank disc's image on the Desktop, even though the Finder's Preferences and the System's Preferences are set to have it open in the Finder—nothing should be on my Desktop! (Note: When transferring the items (all folders) I want to burn to the blank disc, I did not use the Option-Click-Drag method as before, I used the Click-Drag method, which created the curved arrow in the lower left corner of each item.)
Now, for the result of "method 2," the method we basically have in common, the computer goes through the burn stage but, in the verify stage, tells me that it is unable to verify the disk, suggests that my DVD may be unreliable and that I should try another disc, and then tells me about some "fork" (?) error (-43).
I don't know what to do anymore...

Wireless Network Not Working In Bootcamp

I have an early 2006 MacBook Pro running on Snow Leopard and I just ran Bootcamp and installed Windows Xp Pro Service Pack 2. My wireless network adaptor is an Atheros AR5006X. I've installed the drivers in Windows from the Snow Leopard disc and the hardware is recognized, and wireless networks are detected. But I can't connect to any network. I've tried going into Advanced Settings, disabled firewall, I've tried manually setting it up as a preferred network, and I've tried a few other versions of the Atheros drivers from the Internet. Nothing has worked. It always says,
"Windows is unable to connect to the selected network. The network may no longer be in range. Please refresh the list of available networks, and try to connect again."
The signal strength can even be strong and it still won't connected. I never had this problem when I first used bootcamp with the same windows xp sp2, and with the original Leopard drivers disc that you burned when configuring bootcamp.
Please help. Thanks.

There are a number of discussions on this topic. In my previous response, I was referring to the first thread:
Wireless Mouse and Keyboard Not Working in Boot Camp
http://discussions.apple.com/thread.jspa?messageID=6415376&#6415376
I got my wireless keyboard to work in Bootcamp/XP
http://discussions.apple.com/thread.jspa?messageID=6314636&#6314636
keyboard & mouse stop working after apple driver install
http://discussions.apple.com/thread.jspa?messageID=6276210&#6276210
It seems that the basic theme is that if you already installed the Leopard drivers, you will need a non-wireless (USB) keyboard to use/fix it. At this point, you will then need to go and setup the bluetooth to the wireless keyboard. My wireless mouse worked, so that was not a problem -- just the keyboard. I tried using the USB keyboard and seting up the bluetooth to the wireless keyboard, but I could not get it to recognize the bluetooth keyboard. It seems to recognize it for a brief instant, and then report and error.
I've gotten tired of iterating over this issue, so I haven't read through all of the threads. There may be a better one out there that I've missed...

I HAVE EARLIER PREPARED WINDOWS REPAIR DISC, NOW IT DOES NOT WORK

140525
I HAVE WINDOWS 7 ULTIMATE VERSION- 32 BIT
I HAVE EARLIER PREPARED MANY " WINDOWS REPAIR DISC" FROM TIME TO TIME AS A PROTECTION ON THIS VERY LAPTOP AND OS.
NOW IT DOES NOT WORK AND GIVE ERROR CODE -- 0XC00AA0301.
I TRIED SEVERAL TIMES AND WASTED QUITE A FEW DVD'S.
CAN YOU GUIDE?
REPLY ON [email protected]
HOPE TO RECEIVE HELP.
GJDMBH

Once downloaded the Window7 setup you then want to download the windows free burning app from the same thread.
Also visit the Microsoft website link below as has basic guidance that may help you.
http://www.microsoftstore.com/store/msusa/html/pbPage.Help_Win7_usbdvd_dwnTool
Basically with the Windows free burning app you can make either a USB boot stick media of windows 7 or a good older fashioned DVD boot media. Just follow instructions & see how you go, if get stuck come back to this thread & post details on your issue - hopefully myself or other members will be able assist you further if needed.
Like my post? Click Kudos (thumb+) to show appreciation.

Help - Airport network not working - confused!!

Hello, I wonder if anyone out there can help. I have got a problem with my airport network that doesn't make any sense and I havent seen another post with the same problems.
I have an imac G5 with 10.3.9. I have a wireless network set up, with an airport wireless card and two ax boxes (the second was bought later to boost the signal when we moved the Mac to another room). Initially it set up fine and worked for about 8-9 months. Then I noticed the second ax started behaving strangely. It would occasionally turn from 'green' to flashing amber for no reason - often after it had been on for a while. Turning it off and on did not change anything. Usually though it would work again the next day after being off all night. This continued to happen randomly until a couple of months later it switched to flashing amber continually.
I thought it had 'lost' the network so I tried using the airport set up assistant to reconnect it. However the set up assistant does not recognise ax number 2 any more, so I am not able to reconnect it. At the moment I am running off a faint signal from ax number 1.
I also tried setting up a completely new network from scratch. Again the new network is fine from the base ax bx but ax number 2 is still not recognised by my mac.
I also have a wireless printer connected to the network which does not work any more. This is where things became more confusing. The printer needs a boost signal to operate so when my booster ax went wrong the printer would not work. So I moved the printer and mac nearer ax number 1 to ensure it would pick up the network. However it still didn't work. So I attempted to set up the printer as wireless again, thinking it had become 'disconnected' somehow. However during installation you have to select the network to connect to. The computer would not pick up the apple network at all from ax number 1, yet it easily recognises our neighbours network from the flat above us. Strangely when I tried turning on the faulty ax box, the printer set up program picked up the faulty ax and not the original ax. But obviously I can't use the printer from the faulty ax box because it doesnt connect to the rest of the network.
So now I am confused. I am not sure what has gone wrong and what I need to replace. Originally I thought it was the second ax box that had gone wrong. But as the printer software can identify the second ax box I am not sure that this is the problem. Could there be something wrong with the airport card? I have checked that the card is properly connected and there is nothing visibly wrong there.
If anyone can help - please reply as I am going crazy here with things not working and don't know what to do next.
Thanks, Wrenster

Hello Wrenster,
I understand why you are confused, I was too while reading your post. However I have the solution for you. I believe you are a victim of environmental interference. Someone in your neighborhood just moved in with a another network, someone had a baby and is using a baby monitor, or maybe a local ham radio operator just got his license. Who knows!
This is what you need to do. Get all the devices in the same room and preform a hard restart on each one them per http://docs.info.apple.com/article.html?artnum=108044. Remember to preform a hard restart! After performing a hard restart on all three devices check the wireless networks available. You should have 3 ( one main and 2 airport expresses) ( or two depending on how many airports you own, I am not sure from your post). If you don't have the correct amount you may a bum base station and it may need to be replaced. But if you have the correct number of wireless networks ( Apple network XXXXXXX), use the airport admin utility ( inside of the utility folder ) to locate the main base station and configure it.
You will know when you are on the configuration page when you can read Name, Contact and Location.
First change the name to the location of the main base station, ie; it is the den so name should read DEN. leave the contact and location alone. On the bottom half of the page is where you create your network, so under network name change it to your desired network name ie; when others come over to my house I have them select COWSWEAT from the network list.
Second click on the change wireless security and set the security to WEP 128 BIT and make your password. Once you have configured a successful password be sure to click on the lock on the main configuration page ( the one with password under it) to get the HEX password for your PC friends.
Third ( we are almost done ) Select the WDS tab at the top and enable this base station as a main station. Select allow other wireless client on this base station as well. Now on that empty list box below click the plus sign to the right to add other base stations to this WDS network. From here you should be able to select the other 2 base station that we have not configure yet ( but preformed a hard restart on). After you have added them ( be sure the check box for auto configure is selected) they should read in the list that was empty on the WDS page.
Now update this should start the update process and may take 5-10 mins, it should provide a summery pop-up when with each station is done.
( Also you may get a message that there is update for the base station, please preform the updates for the selected base stations)
Now when it is completed check to see how many networks you have available ( it should only be one ). Select the network and confirm that all of your base stations appear under the select a base station in Airport admin utility, then move them back to their homes around the house. Giving them 45 secs to restart they should turn green if not , they could out of range of each other or the environmental interference could be affecting them. So you my need to rearrange them until they all green.
Good Luck,
Cowsweat

PIX 501 config - access to internal network not working from remote VPN users - everything on the inside is OK

One other thing - I had a problem with the key pairing so I rebuilt the rsa 1024 and the unit started working. Unfortunately I reloaded without the config in place and now I cannot get it to work again. Any help will be greatly apprecaited although I did review a dozen other posts of people having similar problems and for some reason there is never any conclusion as to the solution and I am not sure why.
Some other info from the client end:
I just ran the stats on the client and packets are being encrypted BUT none are decrypted.
Also Tunnel received 0 and sent 115119
Encryption is 168-bit 3-DES
Authentication is HMAC-SHA1
also even though the allow LAN is selected in the Cisco VPN client it states the local LAN is disabled in the client stats
also Transparent tunneling is selcted but in the stats it states it is inactive
I am connecting with the Cisco VPN Client Ver 5.0.07.0440
This config works. It is on the internal net 192.168..40.x and all users obtain dhcp and surf the web. It has required ports opened.The problem is that you can connect remotely via the VPN and you receive an IP address from the remote-vpn pool but you cannot see any machines on the internal network. The pix is at 40.2 and you cannot ping the pix and the pix from the remote PC connecting via the VPN and youcannot ping the remote PC from the PIX console when the remote is connected and receives the first IP address in the VPN pool of 192.168.40.25
I need to see the internal network and map network drives. I have another friend that is running the same config and it works but his computer is on a linksys wireless and has an IP of 192.168.1.x and the IP he receives from the VPN pool is 192.168.1.25 so I do not know if the same network is allowing this config to work even if there is an error in the config. In my present case I obtain the ip of 192.168.40.25 from the VPN pool and my connecting pc on 192.168.1.x I really am not sure how the VPN virtual adapter works. I am assuming it routes all traffic from your connecting PC to and from the virtual adapater but I really do not know for sure.
Other people have had similar issues with accessing the internal network from the VPN. One solution was the split-tunnel, another was the natting and another had to do with the encrption where there and an issue with the encrypt and ecrypt which was stopping the communicaton via the VPN.
I still cannot seem to find the issue with this config and any help will be greatly appreciated.
This is the config
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password somepassword
hostname hostname
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
object-group network internal_trusted_net
network-object 192.168.40.0 255.255.255.0
object-group icmp-type icmp_outside
icmp-object echo-reply
icmp-object unreachable
icmp-object time-exceeded
icmp-object source-quench
access-list OutToIn permit icmp any xxx.xxx.xxx.0 255.255.255.248 object-group icmp_outside
access-list no_nat_inside permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list split_tunnel permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list OutToIn permit ip any any
access-list outbound permit ip any any
(NOTE: I had many more entries in the access list but removed them. Even with the above two allowing everything it does not work)
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside xxx.xxx.xxx.xxx 255.255.255.248
ip address inside 192.168.40.2 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpn_client_pool 192.168.40.25-192.168.40.30
pdm history enable
arp timeout 14400
global (outside) 1 interface
I had this statement missing from the previous posted config but even with the nat (inside) 0 access-list no_nat_inside it still does not work.
nat (inside) 0 access-list no_nat_inside
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group acl_outside_in in interface outside
access-group outbound in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.40.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community $XXXXXX$
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set 3des_strong esp-3des esp-sha-hmac
crypto dynamic-map clientmap 50 set transform-set 3des_strong
crypto map vpn 50 ipsec-isakmp dynamic clientmap
crypto map vpn client configuration address initiate
crypto map vpn client configuration address respond
crypto map vpn client authentication LOCAL
crypto map vpn interface outside
isakmp enable outside
isakmp identity address
isakmp client configuration address-pool local vpn_client_pool outside
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup remote-vpn split-tunnel split_tunnel
vpngroup remote-vpn idle-time 10800
vpngroup remote-vpn password ANOTHER PASSWORD
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 192.168.40.0 255.255.255.0 inside
ssh timeout 30
console timeout 60
dhcpd address 192.168.40.100-192.168.40.131 inside
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
username AUSER password PASSWORD privilege 15
terminal width 80
****************** End of config
I have been searching docs and other people's postings trying to obtain the info to make this work. It appears pretty much boiler plate but I believe my problem is in the natting. I am using a range in the internal network for the VPN pool and I have tried switching this to other networks but this has not helped. Unfortunately I have been unable to get the PDM to work and I believe this is a PC config thing and I did not want to waste the time on it. I read a post where a person using the PDM interface with the same problem (not being able to access the internal network) was able to go to a section in the VPN wizard and set the Address Exeption Translation. They said they originally set the VPN subnet when they did not have to. Many of the other blogs I read also stated that if the natting is not proper for the VPN pool- that it will not work but I am confused by the examples. They show as I do the complete range for an access-list called no_nat_inside but I believe it should only have the VPN pool IP range and not the entire network since the others do require natting - not sure if my thought process is correct here. Any help will be greatly apprecaited. Also this morning I just tried a boiler plate example from CISCO and it also did not do what I need for it to do. And I also connect a PC to obtain an IP to see if I can see it - no good. The PC can ping the PIX and viceversa but no one can ping the remote PC that connects via the CISCO Remote VPN client even though it receive an address from the vpnpool. Also include LAN is checked off on the client. This was mentioned in anther post.
Thank you once again.

Hi,
PIX501 is a very very old Cisco firewall that has not been sold for a long time to my understanding. It also doesnt support even close to new software levels.
If you wanted to replace the PIX501 the corresponding model nowadays would be ASA5505 which is the smallest Cisco ASA firewall with 8 switch port module. There is already a new ASA5500-X Series (while ASA5505 is of the original ASA 5500 Series) but they have not yet introduced a replacing model for this model nor have they stopped selling this unit. I have a couple of them at home. Though naturally they are more expensive than your usual consumer firewalls.
But if you wanted to replace your PIX firewall then I would probably suggest ASA5505. Naturally you could get some other models too but the cost naturally rises even more. I am not sure at what price these are sold as used.
I used some PIX501 firewalls at the start of my career but have not used them in ages since ASA5505 is pretty much the firewall model we use when we need a firewall/vpn device for a smaller network/branch site.
Here is a PDF of the original ASA5500 Series.
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.pdf
Here is a PDF of the new ASA5500-X Series
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/at_a_glance_c45-701635.pdf
I am afraid that its very hard for me atleast to troubleshoot this especially since I have not seen any outputs yet. Also the very old CLI and lack of GUI (?) make it harder to see what the problem is.
Could you provide the requested outputs?
From the PIX after connection test
show crypto ipsec sa
Screen captures of the VPN Client routing and statistics sections.
- Jouni

Extending wireless network, not working?

ive been trying to set up a new wireless network for a few days now and while i got this network up and running i still doubt if its exactly what i want.
i have extreme(n), time capsule(n) and an express(n). im using the extreme as my "base" which is connected to the internet and both the capsule and express are connected by wires. but whenever i use the setting "extend a wireless network", the stations will just become undetectable and not working at all. so to get my network to work i configured them all with "create a wireless network" giving them all the same network name which is working fine. but is this even roaming?

Welcome to the discussions!
When you are having extending difficulties, it's often helpful to temporarily locate the Express near your main router...across the room or in an adjacent room and test to see if that works.
If things worked fine for 6 months and suddenly you have problems, that may indicate that a new wireless network near you has been added at one of your neighbors, which is causing interference on your network.
Cordless phones are a real problem as well. My neighbor...across the street....can literally knock me off my network if he is in his front hard talking on his cordless phone. I found this out simply by accident, otherwise I would still be blaming Apple for stuff that worked fine for months and then suddenly did not work.
If the Express works close to the main router, then move the Express further away and test again. Most users locate the Express too far away from the main router when they try to extend a wireless network. A good starting location is a point that is about 1/2 to 2/3 of the distance between the main router and the area that needs more coverage.
Open AirPort Utility and click on your AirPort Express on the left and look for its AirPort ID on the right. Jot that down.
When you are testing the extension of the Express, move your laptop close the Express, and hold down the option key on your Mac while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. This should match the AirPort ID of the Express, indicating that your computer is connecting to the AirPort Express.

Over / Under payment not working

My over and under payment setup stopped working after I installed p42...I then upgraded to p47 and it still is not working, has anyone else experienced this problem?
I have all my set ups done, GL's, doc settings etc....it just will not post my difference and reconcile the document. HELP any ideas
Joanne

I have found the issue, please disregard
Jo

Scroll over highlight function not working on custom nav bar links

Hi - I've created a custom nav bar in iWeb (www.HollywoodRC.com). I have it set up so that the text highlights when scrolled over. This function works in iWeb but does not work on my published site in Safari; however, works in my published site on IE. Any ideas on how to get the scroll over highlight to work on my published safari site? All the links work properly.
Thanks,
Steve

No. Things must have changed. I created a hyperlink with a non web safe font, LedgerD, added a drop shadow and published. I also put the same link in a shape. You can see them in this test page: Page-1 . The two items are image files but they do not contain the link text. Very strange. The hyperlink text can't be selected nor dragged to the desktop like other links, like the Click to Play links on the page, however.
However, I don't know how IE will handle it. According to this IE emulator site, http://ipinfo.info/netrenderer/, IE can see the drop shadow. But it doesn't tell us how the links will work.

Bridged networking not working with nested VMware Workstation

I am having an issue that I can't seem to find any answer to....
We are running Vsphere 5.5 and I have 2 Guests each running Windows 7 64-bit. Each of these guests has VMware Workstation 10 running on them. When we P2V the systems we followed all the instructions to allow nested VMware Workstation. However, we are running into an issue where the Bridged Networking will not work. Both of the Win7 guests are on the same vlan and all of the VMs in Workstation are on the same network as well. However, while the 2 Windows 7 guests can ping each other and each of the guests can ping the VMs that are hosted locally, they cannot connect to the systems on the other guest running workstation.
I tried to upgrade the Guest NIC to VMXNet3, but that did not help.
All of the research I have done brings me to people who are having the opposite problem (ESXi nested in VMware Workstation).
How can I get the 2 bridged networks to connect?
Thanks!

The ESXi vSwitch to which the outer guests are connected must be configured for promiscuous mode and forged transmits.

EA4500 Guest Network not working

A few days ago I saw there was an upgrade for my router. I clicked on it and away I went. Since updating my guest network isn't working. My android and Kindle HD find the guest network, attach but no prompt for password ever shows up like it did before. The web page will time out and die. Does anyone have a clue why my devices don't prompt for a password anymore?

cperficio wrote:
A few days ago I saw there was an upgrade for my router. I clicked on it and away I went. Since updating my guest network isn't working. My android and Kindle HD find the guest network, attach but no prompt for password ever shows up like it did before. The web page will time out and die. Does anyone have a clue why my devices don't prompt for a password anymore?'i clicked on it and away it went' could be the problem. as much as linksys would like to think it works that way, it has been shown time and time again that the best way to update is to:download the update file to a pc with a wired connection factory reset the routerflash the file from that wired pcfactory reset againconfig from scratch not a backupyou might try to do a factory reset and config and see if it clears the issue. also on those devices that are not working try forgetting the connection and connect again.

Burning discs over a network not working.

Similar Messages

Maybe you are looking for