Busted Screen, Need Help Hooking Up Monitor
The screen on my Powerbook is totally busted so I tried hooking up a monitor to it, but it seems to not be working correctly. All I see is my desktop picture, and no icons (like the HD or folders on my desktop), dock, or even the menu bar are not showing up. At first, I thought it was a ratio issue since the monitor is more square than the laptop screen, and therefore cutting the edges out where the menu bar, etc. would lie, but I'm pretty sure that's not the issue. I'm guessing I have to go into my system prefs and set the computer up to work with the monitor, but the problem is since the screen's totally shot, I can't even go in and do that. Any suggestions? Thanks!
Hi, hobageeba. What is the maximum resolution offered by your external monitor (consult its manual or the manufacturer's online specs for it)?
If the external monitor's maximum resolution (1024 x 768 or 1600 x 1200, for example) is as large as or larger than the maximum resolution of your Powerbook's display, you may be able to get a normal desktop — including the menu bar, desktop icons, etc. — displayed on the external monitor by pressing the F7 key on the Powerbook's keyboard. That should toggle the external display from Extended Desktop mode into Display Mirroring mode, in which the same video signal is sent to both displays, allowing you to use the external as the main display. (Note: under some circumstances, toggling F7 has no effect — and I don't know what circumstances, or why not. If it doesn't seem to do anything, it probably hasn't done anything, and it won't be helpful to you.)
Typically, if the external monitor's resolution is higher than the built-in display's, a mirrored video image will be displayed in the center of it surrounded by black, instead of filling the monitor. That wastes screen real estate, but at least you know you're seeing the whole desktop, and if your monitor is good, the image will be as sharp as it was on the built-in display when it worked.
If the external monitor has a lower maximum resolution than the built-in screen, the results of switching to Mirrored mode are less predictable. You may see only the center of the desktop, with the menu bar, hard drive icon, and other icons that were at the edges of the desktop "displayed" outside the edges of the external monitor. In that case it may be impossible to tell the difference between Mirrored and Extended Desktop modes, depending on what your desktop background image is. I don't know of a way to overcome that.
Whatever you find out about the monitor's resolution, give the F7 toggle a try and see what happens.
Message was edited by: eww
Similar Messages
-
my screen is completely white, i've tried holding lock and home buttons as seen on you tube something called 'white screen of death' its goes black (think it switches off) then back to the white screen need help fast please!
If you have not done a factory reset on the device, I recommend doing a complete factory reset.
Factory Reset - Warning this will reset device back to original factory settings.
This method will not erase any MDN/MIN information
Turn off the phone
Press Power + Volume Up/Down at the same time and hold until display will show a triage android screen
Display will show:
Reboot system Now
Apply sdcard:update.zip
Wipe Data/Factory Reset
Wipe Cache Partition
Use VOL Down key to scroll down to "Wipe Data/Factory Reset", press home icon to select option and wipe device.
Display shows "All user data will be wiped out", press VOLUME Up to continue or VOLUME Down to exit.
Press Volume Up
Press Home to select "Reset System Now" - device will reboot
If the problem persist I recommend having a store technician take a look at the device.
Copy and paste the link below into your browser's address bar for the store locator.
http://www.verizonwireless.com/b2c/storelocator/index.jsp -
Need help connecting external monitor
My brother needs help with connecting an external monitor to his 20" iMac G5. He has the adapter with the standard monitor port, and when plugged in, the monitor duplicates the iMac screen. His question is, how can he set it so that the desktop is extended, instead of duplicated? I, myself, have a MacBook and two months ago I used my adapter to connect a projector, and I remember an option where I could choose between duplicate and extended desktop, and right now I tried to find it on my MacBook and well as my Intel iMac and I can't find the option, and neither can he.
Please help, thanks!The iMac G5 can only mirror the internal display unless you hack the firmware.
Display options like that only appear when you connect a display which is why you can't see them on the MB at the moment.
mrtotes -
Need help with dual monitor setup for KDE 3.5.5.
Here's my hardware:
NEC MultiSync LCD 1530V: 1024x768 (analog)
Samsung SyncMaster 941BW: 1440x900 (digital)
nVidia Dual head AGP video card.
The dual monitor works under dual-boot Windows, boot up and pure Linux console. I've googled around for help, changed my xorg.conf file accordingly to some sites, but it wasn't much help.
Here's my working xorg.conf:
Section "ServerLayout"
Identifier "Simple Layout"
Screen "Screen 1" 0 0
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Section "Files"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "freetype"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard1"
Driver "kbd"
Option "AutoRepeat" "500 30"
Option "XkbRules" "xorg"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Auto" # Auto detect
Option "Device" "/dev/input/mice"
EndSection
Section "Monitor"
Identifier "NEC LCD1530V"
HorizSync 31.5 - 48.5
VertRefresh 50.0 - 70.0
EndSection
Section "Device"
Identifier "Standard VGA"
Driver "vga"
VendorName "Unknown"
BoardName "Unknown"
EndSection
Section "Device"
Identifier "NVIDIA GeForce"
Driver "nvidia"
Option "NoLogo" "true"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "NVIDIA GeForce"
Monitor "NEC LCD1530V"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Using this xorg.conf file, only my NEC LCD analog monitor could display KDE while the Samsung digital can't.
Any suggestions?Thanks for your help guys, I'm halfway there.
The second monitor shows the KDE desktop, but it isn't exactly what I expected. Right now, both monitors display at 1024x768 (each) or 2048x768 (total). The larger monitor stretches and distorts the display of 1024x768 to its natural resolution at 1440x900 and it isn't what I wanted. Other than that, the dual desktop setup behaves what I expected to.
Here's a snippet of my xorg.conf that currently works:
Section "Monitor"
Identifier "NEC LCD1530V"
HorizSync 31.5 - 48.5
VertRefresh 50.0 - 70.0
EndSection
Section "Monitor"
Identifier "Samsung SyncMaster"
HorizSync 31.5 - 60
VertRefresh 60.0 - 70.0
EndSection
Section "Device"
#VideoRam 131072
# Insert Clocks lines here if appropriate
Identifier "NVIDIA GeForce"
Driver "nvidia"
Option "NoLogo" "true"
Option "TwinView" "true"
Option "TwinViewOrientation" "LeftOf"
Option "SecondMonitorHorizSync" "30-50"
Option "SecondMonitorVertRefresh" "60"
# Option "MetaModes" "1440x900, 1440x900; 1024x768, 1024x768"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "NVIDIA GeForce"
Monitor "NEC LCD1530V"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen 2"
Device "NVIDIA GeForce"
Monitor "Samsung SyncMaster"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1440x900"
EndSubSection
EndSection
Anyone have an idea?
EDIT: Oh snaps. I just did a pacman -Syu and it upgraded Arch Linux to 0.8 and the 2nd monitor stopped working. -
Need help hooking up Maxent 42" Plasma to mac mini
i have a newly acquired maxent 42" plasma product number mx42xm11 i called their rep and he said it wouldnt work but i have read a couple forums where people have gotten other maxent monitors to work i was wondering if someone could help me set this one up.
I searched and found this:
Input/Output connections
2 x Composite video input (RCA phono), 1 x DVI-HDCP (24 pin digital DVI), 2 x S-Video input (4 pin mini-DIN), 2 x HD component input (RCA phono x 3), 1 x VGA input (15 pin HD D-Sub (HD-15)), 6 x Audio line-in (RCA phono x 2), 1 x Subwoofer output (RCA phono), 1 x Audio line-out (RCA phono x 2), 1 x VGA output (15 pin HD D-Sub (HD-15)), 1 x Serial (9 pin D-Sub)
It looks as simple as connecting a standard VGA cable from the Mini to the VGA port. It also listed the resolution as 1024x768, which is a standard 4:3 resolution.
You could also try a DVI cable as long as your DVI input looked similar to tha back of your Mini.
Where would you need help?
Greg -
Need help getting LCD monitor to work with G4 GeForce4 MX
I have a G4 that I haven't been using and want to get running again. It has a Nvidia GeForce4 MX video card. I had a huge CRT monitor and want to use a ViewSonic VX1935wm which I got a deal on. When I hook the monitor up it says that the resolution is out of range.
I can boot with my old monitor and change the connection and then get the LCD to work but only at certain resolutions.
Do I need to get a new video card, or can I get an adaptor? What kind of card should I get if it needs to be replaced? Or what other kind of monitor would be supported by this video card?
Here is the webpage for this monitor: http://www.viewsonic.com/products/lcddisplays/xseries/vx1935wm/thanks for the links.
switchResX does something, but it doesn't solve the problem. i can now switch to the "optimum" resolution of 1440x900, 60hz. but when i restart the computer, it still won't work! i continue to get the "out of range" message and have to boot with my crt and then switch cables to do anything. also, the fonts in the finder menus look terrible, you can see the jagged lines.
displayConfigX won't let me test that high of a resolution without registering the product.. needless to say, i don't want to pay money if the results are going to be the same as with SwitchResX.
I sent an e-mail to ViewSonic support. Is it typical to have these problems? I am getting more and more confused as I learn more about this. -
i can't sign in to game center in the mac i type i the password and it takes me to a black green screen i need help?
I have the same problem on my Mac OS X V 10.9.5. and its just 1 month old.
have tried almost everything. But it looks like it's on Apple's side because there are other people with other devices (Iphone & Ipad) having the same problem.
screenshot: -
Need help hooking up my macbook from 2009 to my samsung B2430HD LCD monitor
can not get a clear picture when hooking up my macbook to a 24inch LCD samsung b2430hd I have a mini dp to hdmi and hooked up the other end of the hdmi cable to my monitor but it isnt perfect quality it looks a little blurry. someone please help me! should I get a mini dp to vga and hook it up with a vga connection? I also read that I should change the 60 hertz to a lower one. Why wouldnt it work with HDMI I thought HDMI was the best quality? Is it because the samsung monitor isnt compatible with MAC's? please help
Csound1 wrote:
AlexxHansson wrote:
Sorry, just closed all the tabs.
Thank you for trying to help. I´ll post the links if i find them again.
The links are in your history, one click and you'll have them and you can post them for all to see.
Would take to long to find them all with good information. But this is one.
https://discussions.apple.com/thread/2355403?start=0&tstart=0
And then i tried this:
http://hints.macworld.com/article.php?story=20090828224632809
Didnt work either.
The maximum resolution for the monitor is 1080p. I have no problem getting this from my computer. When i use the HDMI i get 1080p, when i use VGA i get 1920 x 1080. Hmm -
Need help with external monitor
ok here it is my duaghter pushed my powerbook off hte table and it broke the screen and i have purchased a dvi to vga adapter to work on a n external monitor is there anything else i need to do to make it work right now all i get is white screen anyhelp willbe greatly appreciated
The VGA adapter is only 4" long, do you have an extension? If so, the computer should register the adapter and the images should be displayed. Any more details would help to see what's wrong.
Ray -
I need help choosing a monitor! PLEASE HELP!
I getting a brand new mac mini from ebay and i am deciding between a 15-inch or a 14-inch LCD display. I was just wondering, if both of the displays have a resolution of 1024 x 768, is that the pixel count too? so does that mean the pixels on the 15-inch are just bigger or something? i need to know because the 14-inch LCD is $40 cheaper than the 15 inch....Thanks everyone!
also, since i've already decided on getting an apple keyboard, do you think the mighty mouse is really worth $49? i like to stick with apple products so that's why I'm wondering.
~CHRIS~It doesn't necessarily mean the pixels themselves are bigger or smaller. It could also be the dot pitch (or distance between pixels) is bigger or smaller. If the native resolution is 1024x768 then you are correct, there are physically 1024x768=786,432 pixels. A 15" screen with the same resolution as a 14" screen may appear slightly less sharp but objects will appear larger. It's a tradeoff. Generally I would choose the larger monitor just because it is easier on the eyes when reading small print, etc.
Hope that helps,
-CW -
Need Help Bad, Program Monitor Troubles
Ive reinstalled windows 7 5 times in the last 3 days, my problem that im having is when i opening up premiere everything is find i think seems to be running fine. but when i try to color correct anything and i select any peramater in an effect im not seeing the updated in the program monitor.
I dont know what this is doing this. its like trying to color correct and guessing. the video updates if i stop and give it a sec to load. in other version of PM ive done this with no problems. i just got this system its an i7, 16gb ram with 2gb nvidia video cards. I dont know the tearm of whats happening only thing i can think to call it is the program monitor is out of sync. im pulling my hair out over here. can someone help me please here is a video so u can see what im saying. http://www.youtube.com/watch?v=tkN33DQNZag&feature=plcp
please help me here ive been looking for help for 2weeks and have gotten nowhere ive been to youtube and copied people settings inside of the nvidia control pannel. i just need someone that knows what this can be.>2gb nvidia video cards
Do you really have more than one nVidia card?
Did you know that 2 cards does not always work well in PPro?
Dual Card SLI http://forums.adobe.com/thread/872941
-problem http://forums.adobe.com/thread/872103
Also, More information needed for someone to help... click these links and provide the requested information
-http://forums.adobe.com/message/4200840
-http://forums.adobe.com/thread/416679
-http://forums.adobe.com/thread/419406
Read Bill Hunt on a file type as WRAPPER http://forums.adobe.com/thread/440037
What is a CODEC... a Primer http://forums.adobe.com/thread/546811
What CODEC is INSIDE that file? http://forums.adobe.com/thread/440037
Report back with the codec details of your file, use the programs below... a screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30
For PC http://mediainfo.sourceforge.net/en or http://www.headbands.com/gspot/
http://blogs.adobe.com/premiereprotraining/2011/02/red-yellow-and-green-render-bars.html -
HP Pavilion a6000 desktop with Vista black screen - need help please!
I have an HP Pavilion a6000 desktop with Vista. Yesterday it was working fine and today we have the black screen that reads:
Award BootBlock BIOS v1.0
Copyright (c) 2000, Award Software, Inc.
BIOS ROM checksum error
Detecting IDE ATAPI device...
Found CDROM, try to boot from it...Fail
Detecting IDE ATAPI device...
Detecting IDE ATAPI device...
Detecting floppy drive A media...
Drive A error. System halt
I am not a techie, but looked at online forums and have tried f10 at startup with no change to the screen other than it stops after the first four lines and does not try the floppy drive. I also pulled out the round battery, waited and then reintstalled. Same problem.
Also, computer emits a single, repeating beep after startup.
HELP!jjeahall
I saw your post and wanted to comment. I'm not an expert on these types of situations but did some digging around and found the following at Tips4PC.com.... read below
"There are two types of computer black screens that can appear in Windows. One where the computer will not boot up but you have a beep sequence sounding to let you know what the problem could be, and the other has nothing at all. No beeps, no cursor, no logo screen, and no choice to boot to safe mode or access the bios.
If your computer will not boot up and you get a beep sequence, I am not saying it is good news, however it is a step in the right direction towards solving this problem. This is a message from your computer that can be understood by looking up your bios (the brand) beep code. For example you may have an Award Bios, Ami Bios, Phoenix BIOS, Compaq, Dell, or Acer Bios. This list goes on and on. You can search for Bios beep codes in Google. Here is an example of results in Google search"
Link
Also I went into the Troubleshooting Guide for the A6000 and found the following information. You need to use F11 for recovery. See below
Starting System Recovery from system startup
1
Turn off the computer. If necessary, press and hold the On button until the computer
turns off.
2
Remove the HP Personal Media Drive if your computer includes one. Disconnect all
peripheral devices from the computer except the monitor, the keyboard, and the
mouse.
3
Press the On button to turn on the computer.
4
During the startup, do the following to enter the Recovery Manager program:
When the blue screen with the HP Invent logo appears, press the F11 key on the
keyboard. (You have only a few seconds to press the F11 key before the normal
startup process continues.)
5
The computer starts the Recovery Manager program; wait for the onscreen instructions
to display, and then follow those instructions.
6
Complete the computer startup, finish the registration process, and wait until you see
the desktop. Then, turn off the computer, reconnect all peripheral devices, and turn on
the computer.
I am an HP employee.
Regards,
Cooper56
If you’ve found this information helpful, please make it easier for others who might be experiencing a similar type issue by marking my answer as “Accept as Solution” .
***Of course you can also Click on “Kudos” STAR to say thanks!***
I work for HP. When your problem has been solved, accept the solution by clicking the "Accept as Solution" button to help other members in the future! -
Hello everyone, I have an old Emac which the monitor popped and stopped working. I bought the plug and had an external older monitor working once, then I plugged in a newer monitor and now neither will work. The xternal monitor has a small blue rectangle bouncing around saying "please check pc display settings. I tried to reset the ram by restarting the Emac and holding down the command,option,p, and r buttons. This made the second restart sound, but the video still does not work. Is there another sequence to reset? Am I doomed now? Any help is appreciated. Thank you.
Hello again, yes it was the picture tube that went. the smell was awful. The machine still runs, but since I plugged the flat screen monitor into it, it will not display either monitor. It was working once with an older monitor, but now it just diplays "adjust pc display settings". I needs to view the emac so I can retrieve my files. I've also tried resetting the pram, but that did not work. What can I do? I'm stuck. Thx.
-
Major issue! GPU busted! Need help urgently!
I bought this HP pavilion g6 2230tx model around 1.5 years back and since then i have experienced quite a lot of problems with it like hdd crash, heatsink failure, motherboard failure. I'd sent it a lot of times for repair and a lot of my money has already been wasted on it.
Recently, after working fine for about 1 month a new problem took place. Its GPU busted! i dont how, but all of a sudden this dreaded TDR error started coming ("AMD display driver stopped responding and has been recovered"). I tried to sort out this issue in every possible way (trying older driver/ reinstalling OS/ flashing BIOS) but no help. Even the work around by microsoft isn't working! I'm sure that it's GPU is busted.
Now what i need to know is what can i do now? Is this even reapairable? Can i replace the GPU? If yes what'll be the cost?
Please reply!!!
Model: HP pavilion g6 2230txHi @Bleeding_Devil
I see that you are looking are replacing your GPU in your Pavilion g6. Unfortunately, the GPU is soldered onto the system board or motherboard. You would have to look at replacing that again.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP -
I need help hooking my Samsung 27" Class 1080p LED HDTV T27B350ND to my macbook pro
I tried hooking my mac bool pro to this samsung monitor and all I get is the picture of the universe that came with the laptop and my mouse is on the monitor, but that is it.... help?
help with what? sounds like it's working to me.
Maybe you are looking for
-
Chinese Characters Printing as Boxes in SAPscript
Issue...why would a Chinese standard text print fine using the "INCLUDE" method, but output as boxes when that same Chinese standard text is retrieved successfully using the "PERFORM" method? Summary...I am currently experiencing problems printing Ch
-
Plugged my iPhone five into charger overnight and can't get it to turn on this morning
Can't get my phone to power on
-
I bought a ipad 3 refurb. Having problems with it. If I return it ( still in 14 days) or exchange, will I get another refurb 3 or will they give me a 4? There are no refurb 3s available online
-
Does anyone know how to klick on a button in one movie and than go to another movie AND come to a certain frame?
-
hi i am new to sap smartform, i have a requirement to develop a form that consist of employee offer letter. can anybody help me to develop these form , any sugessions where i get gud practice notes for this, plzz do me this as early as possile, if a