Button Templates in database not shwn in CUCM admin Phone Button Templates

Hi,
I was looking around the database of CUCM (v8.6), and i have found some gap between the 'phonetamplate' table and the "Phone Button Templates" page. Following items are not shown in the front-end:
StandardCN622
Standard_Cisco_TelePresence_400
Standard_Cisco_TelePresence_200
Standard_Cisco_TelePresence
Standard Usage Profile
Default VGC Virtual Phone Template
Is this normal behavior? Is there any explanation why?

Hi Anthony,
I think there was device pack installed (cmterm-devicepack8.5.1.14059-1.cop).
How does it explain the gap?
admin:show version active
Active Master Version: 8.6.2.23900-10
Active Version Installed Software Options:
cmterm-8961.9-1-1SR1.cop
cmterm-7937-1-4-5-7-SCCP.cop
cmterm-9951.9-1-2.cop
po-locale-de_DE-9.3.3.1000-1.cop
cmterm-7945_7965-sccp.8-3-5.cop
cmterm-9971.9-3-4-24.cop
cmterm-9971.9-0-09-2dev.cop
cmterm-dx650.10-0-2-24.cop
cmterm-8941_8945-sccp.9-3-4-17.cop
cmterm-7945_7965-sip.9-3-1SR2-1.cop
cm-locale-de_DE-8.6.2.1000-1.cop
cmterm-7945_7965-sccp.9-3-1SR1-1.cop
cmterm-7945_7965-sip.9-3-1SR1-1.cop
cmterm-9951.9-0-1SR1.cop
cmterm-9951.9-0-4.cop
cmterm-69xx-sccp.9-2-2-6.cop
cmterm-7925-sccp.1-3-4SR1.cop
cmterm-9951.9-0-1SBE-10.cop
cmterm-9971.9-3-2SR1-1.cop
cmterm-7942_7962-sccp.9-2-1.cop
cmterm-8961.9-3-1-33.cop
cmterm-7940-7960-sccp.8-1-2.cop
cmterm-9951.9-1-1SR1.cop
cmterm-8961.9-0-1SBE-10.cop
cmterm-roundtable-901-super-7.cop
cmterm-8961.9-3-4-24.cop
cmterm-9971.9-0-3.cop
cmterm-7945_7965-sccp.9-3-1SR2-1.cop
cmterm-9951.9-0-09-2dev.cop
cmterm-69xx-sccp.9-0-2-s.cop
po-locale-zh_CN-9.1.1.1000-1.cop
cmterm-8961.9-0-4.cop
cmterm-9971.9-1-2.cop
ciscocm.refresh_upgrade_v1.1.cop
cmterm-9971-repartition-all.cop
cmterm-9971-repartition-4.cop
cmterm-7945_7965-sccp.9-1-1SR1.cop
cmterm-devicepack8.5.1.14059-1.cop
cmterm-8961.9-3-2-10.cop
cmterm-9971.9-0-4.cop
cmterm-69xx-sccp.9-1-1-sr2.cop
cmterm-9971.9-2-2.cop
cmterm-9971.9-0-0-46dev.cop
cmterm-7945_7965-sccp.9-0-2SR2.cop
cmterm-9971.9-0-1SBE-10.cop
cm-locale-hu_HU-8.5.1.2100-1.cop
cmterm-8961.9-1-2.cop
cmterm-bfcp-e.8-6-2.cop

Similar Messages

When I click the iCloud button I get a browser with check boxes, not slider buttons and it does not have a "backup and storage" button. So I cannot set up backup.

When I open my iCloud browser it looks different than "normal." It shows the list with check boxes, not slider on-off buttons. It dos not show a "storage and backup" button so I cannot set up my backup. What is wrong?

If see something like the image below it's because you are looking at the iCloud settings on your Mac, not on an iOS device (which has sliders). Storage & Backup isn't in the Mac settings because you cannot back up your Mac to iCloud. Only iOS devices can back up to iCloud. On a Mac, you can get information about your iCloud account storage by looking at the green usage bar at the bottom and by clicking the "Manage..." button on the bottom right.

Question: JSF Page Templates inside Template - possible or not?

Hi guys!
I like pageTemplates! Really nice thing to decompose UI (especially supporting ADFm in background :))).
But, when I tried to define new template using another template, I was not able to reach facets of existing template (designer shows the "picture" of existing template but I cannot reach facets nor "enter" the template in any way). Looks like template inheritance is not supported? Or I'm doing something wrong.
Anyone succeeded to define new template based on existing one?
Thanks for any clue,
Pavle

Hey,
I think we should take emotions out for a while and consider the options you have to build "reusable" pieces with templates today.
If you, for example, build a declarative component out of existing layout components and specify facetRefs for areas you want the application developer to change or add cmponents to then this becomes reusable as a ADF library. This said, a change to the declarative component has immediate effect to the decalartive components used on a page and/or template as soon as the new ADF library jar is in. So for basic needs like modifying a base template to contain customized headers etc. I think this should do.
Rgarding "under discussion". We are for sure no idiots and have an eye on the market and application development needs. So its not a discussion of "do we want that feature" - as we all agree on that we want to have this - but, what would be the possible impact that could happen, like performance, access to contained binding references, circular template references, how-deep does it make sense. This - and I hope you agree - should be discussed first and then properly implemented rather than blindly coded into the product.
However, we do have release cycles and some features might come just too late to be within the first cut - unless we want our customers to wait any longer than necessary to get their hands on a production version of JDeveloper 11.
"But, maybe the truth is hidden from the public? Maybe JDev is not intended to be the custom apps dev tool but only "customization" tool for WebCentre and other Oracles applications? That way the focus on taskflows instead on full UI is justified"
Taskflows is part of the Oracle ADFc controller, which is an extension to the Faces controller. It can be used without ADF using plain JSF components and bean binding. Taskflows is badly needed in JSF because it solves many usecases of Ajax that otherwise you can bang your head against a wall on
- isolated memory scope
- isolated transaction handling with "safe for later" commit, and rollback functionality
- declarative back browser handling
- page-to-page navigation within a page
- break up of activity navigations in reusable units
- Declarative JAAS based security
- Defined entry and exit points
Taskflows are not a mean to build reusable layouts, but reusable flows (thats a big difference and will benefit to application development outside of Oracle Applications big times). Of course, some features might be limited to the use with ADF, but I don't think that you can blame us for having technology that enables out-of-the box behavior for what otherwise you have to hand-code.
Regions I think is what you are addressing as a solution to embed "template" alike content.
Frank

IOS 5: Phone button stopped functioning

After updating IOS 5, the phone button at my IP4 has stopped functioning. I can not make phone calls except using contacts button or listen my messages. I see that I have 4 messages but the application switches off after two seconds or does not start after pressing the phone button. There are other problems such battery draining. I realized that notification system is not functioning as well, despite me turning off all notifications I am still getting notifications from NYT and Facebook as well.

It took me a couple of days because most of the time I have the sound turned off. It was only after my son was playing Slice Fractions and asked me to turn on the sound that I noticed it at all and only then because the app was loud as...well, it was really loud.
On the other end of the service report spectrum, for whatever reason, my gut told me to get Apple Care when I got the phone. May have been the persuasive smile of the salesgirl or just good instincts... Still, they were really professional on my text-chat session. We tried a few of the things that were outlined above and then they just set me up with an appointment at the Genius Bar for Wednesday afternoon. I am told there is a good chance that they will give me a new device if they can't fix it on the spot. Since I will be restoring from a backup, the problem, if it is a glitch, should appear on the new phone as well and then we'll have our answer...
Apple Care vs. Taking Care is like the difference between Good Whiskey vs. Cheap Whiskey:
Pay now or Pay later...
I'll keep you posted...

Voicemail red button on phone button (home screen)

This is doing my head in!
For the last two weeks i have had the little red button at the top right hand corner of the phone button telling me i have new voicemail. I dont.... i have made sure many times that i dont have any and that they have all be deleted.
What can i do:( It ruins the look of the home screen.
Im on 1.1.4
Thanks

Hey MatT,
Try resetting the iPhone by holding the Sleep/Wake button and the Home button until you see an Apple appear on the screen.
http://docs.info.apple.com/article.html?artnum=305743
If the number does not go away, try calling standard voicemail to see if everything appears normal there. Goto Phone> Keypad> hold #1 key.
You can also restore the iPhone.
http://docs.info.apple.com/article.html?artnum=305744
Jason

Error while updating phone button template in CUCM 8.6

Experts,
I'm getting following error while updating phone button template in CUCM 8.6;
Update failed. java.sql.SQLException: System catalog (sysprocbody) corrupted.
Please check the screen shot attached here with.
What could be the reason?
Thanks
Vivek

I'm not a Cisco employee, so I can't do anything with your backup.!
You need to take a backup as a precaution (You should have been doing this anyway) Then you need to call Cisco TAC to get the underlying problem fixed. CalManager is a locked-down environment, and only TAC can get the low-level access needed to fix database problems.
GTG

CUCM 6.1 = Phone Button Template Dependencies

Does anyone have a CLI query string built for retrieving phone button template dependencies? I'd like to determine how many unused phone button templates there are, and how many phones use each template.
CUCM 6.1 (or any other version)
Thanks,
Beau

There's the query I used to identify templates with "Individual". These templates are created when you modifiy the line appearance on the device. I had 599 templates I needed to delete or change to device type templates.
admin:run sql select device.name AS Device, phonetemplate.name AS PhoneTemplate from phonetemplate LEFT JOIN device ON device.fkphonetemplate = phonetemplate.pkid WHERE phonetemplate.name like '%ndividual%' order by device.name
Example Output - the devices showing NULL are the phone templates not assigned (no dependency). While the last template is assigned to the DEVICE - SEPAABBCCDDEEFF
device                               phonetemplate
===============          ========================================
NULL                                NotAssigned-SCCP-Individual Template
NULL                                SEPFFEEDDCCBBAA-SCCP-Individual Template
SEPAABBCCDDEEFF       SEPAABBCCDDEEFF-SCCP-Individual Template

Button template's styleClass not working

We have created our own button template in UIX, which specifies a default style and JavaScript mouse events so that the button visually changes when the user hovers the mouse over it.
This works, except that on startup, the default class that we assign to the button isn't there in the generated HTML.
The onMouseOut/onMouseOver events do work however, so we get the weird situation that our buttons look all wrong, but they look correct once the user has moved the mouse over them at least once.
Does anyone have any idea? Here's our UIT file:
<templateDefinition xmlns="http://xmlns.oracle.com/uix/ui"
xmlns:data="http://xmlns.oracle.com/uix/ui"
xmlns:ui="http://xmlns.oracle.com/uix/ui"
xmlns:html="http://www.w3.org/TR/REC-html40"
expressionLanguage="el"
targetNamespace="http://xmlns.psb.nl/osiris/templates"
localName="button">
<type base="ui:button">
<attribute name="text" javaType="string"/>
</type>
<content>
<button styleClass="UnselectedButton"
onMouseOut="this.className='UnselectedButton';"
onMouseOver="this.className='SelectedButton';">
<attributeMap>
<rootAttributeMap/>
</attributeMap>
<childMap>
<rootChildMap/>
</childMap>
</button>
</content>
</templateDefinition>

From daniel.early79 at this thread: https://discussions.apple.com/thread/4894152?start=6&tstart=6
I just experienced the same issue of my down volume button not working but the up volume button does. I messed around with the phone for a bit. I just found out that if I hold the iPhone in my right hand with my thumb on the upper right corner of the phone and apply slight pressure on the upper right corner, the down volume button worked. After doing this a couple times it started working normally again. Must be a design issue. Hope this helps!

Changes to phone devices in CUCM admin console not being configured on phone

I can log in to the CUCM admin page and make changes to phone devices. The changes made are reflected in both the PUB and both SUBs. Devices do not take changes however. Reset and restart commands from admin page on devices do not actually reset or restart devices. Physically resetting device by unplugging switch port on phone does not help reflect configuration changes. Verified TFTP settings are correct and reset the TFTP service on servers. Troubleshooted on Cisco phone 7945 and 8945. Any help on how to resolve this?
CUCM ver. 9.1.2
Phones 7945 Phone Load 9-3-1SR3-1S
Phone 8945 Phone Load 9-3-4-17

Hi,
This points to some database issue, the database replication may be broken. Please check through RTMT and see if the database replication state is 2 for all the servers. You can try a 'utils dbreplication stop' on all servers followed by a 'utils dbreplication reset all' on the Publisher. Another quick fix would be a restart of the ccm service.
HTH
Manish

Page from a Template - Nav Bars Not Coming Across

Have Dreamweaver CS4 on XP
I have a template that has an absolute placed div for the
header box...and just below that a 50 pixel absolute placement div
to hold the navigation bar.
The nav bars have 8 different buttons and several sub menus.
They look fine and work fine on the template and they preview in
firefox fine. In the template the header and the nav bars are not
write enabled...but the AP div for site content is write enabled in
the copy pages.
Here is the WEIRD behavior is CS4. In my first child copy
page of the template...I can NOT see the nav bar...but if I upload
it to the server and look at it there...the nav bar is visible. The
nav bar has 2 java scripts that have to be loaded in the root...and
they are there.
In the second page I made...the nav bar is NOT visible, it
does not preview, and it does not show up when I call it from the
server.
Whats UP with Dreamweaver or Me? I have had soo much funky
behavior with templates and resulting pages.
Can someone help figure this out with me. Some post talked
about making the z value of the nav bar be 1100 or 1300 because of
some IE problem...so I did that trying to avoid problems with the z
value being off.
Thanks for your help
Suzzie

Post a link to the page, please.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"suzzie12" <[email protected]> wrote in
message
news:gmr5v7$ou3$[email protected]..
> Have Dreamweaver CS4 on XP
>
> I have a template that has an absolute placed div for
the header box...and
> just below that a 50 pixel absolute placement div to
hold the navigation
> bar.
>
> The nav bars have 8 different buttons and several sub
menus. They look
> fine
> and work fine on the template and they preview in
firefox fine. In the
> template
> the header and the nav bars are not write enabled...but
the AP div for
> site
> content is write enabled in the copy pages.
>
> Here is the WEIRD behavior is CS4. In my first child
copy page of the
> template...I can NOT see the nav bar...but if I upload
it to the server
> and
> look at it there...the nav bar is visible. The nav bar
has 2 java scripts
> that
> have to be loaded in the root...and they are there.
>
> In the second page I made...the nav bar is NOT visible,
it does not
> preview,
> and it does not show up when I call it from the server.
>
> Whats UP with Dreamweaver or Me? I have had soo much
funky behavior with
> templates and resulting pages.
>
> Can someone help figure this out with me. Some post
talked about making
> the z
> value of the nav bar be 1100 or 1300 because of some IE
problem...so I did
> that
> trying to avoid problems with the z value being off.
>
> Thanks for your help
>
> Suzzie
>
>
>

Feature GUID for list template 10113 is not installed in the farm

I'm just using a trial of a migration product called Sharegate and it has produced the following error when i connect it to my farm "Feature GUID for list template 10113 is not installed in the farm"
I've used the missing feature project from codeplex and the wssanalyzefeatures tool and none of them are reporting any issues or even for my guid.
Could anyone provide any other tips to try and locate this via powershell or the sql database?

Hi,
According to your post, my understanding is that you got the “Feature GUID for list template 10113 is not installed in the farm” error.
The reality is that the feature is installed but has the old feature ID.
As a workaround, you can
Go to the concerned feature in the 14 hives, you need to know which feature is concerned with that functionality.
Change the feature ID to the one raised in the error
stsadm -o installfeature -name <Feature> -force
In addition, you can change the ‘Scope’ attribute to either ‘Farm’ or ‘Site’ or ‘Web’ or ‘WebApplication’.
Here are two similar threads for your reference:
http://social.msdn.microsoft.com/Forums/office/en-US/689e22ed-9ec9-46ae-b704-b0684a76f72a/feature-for-xxxxxxxx-list-template-xxx-is-not-installed-in-this-farm-vsewss?forum=sharepointdevelopmentlegacy
http://blogs.msdn.com/b/sowmyancs/archive/2008/04/02/server-error-feature-guid-is-not-installed-in-this-farm-and-cannot-be-added-to-this-scope.aspx
Best Regards,
Linda Li
Linda Li
TechNet Community Support

Shared services database not found in the specified database

Hi Guys,
In Hyperion EPM System confirurator,i gave all the fields and click next button it show error message "Shared services database not found in the specified database"

Hi ,
1. Pls confirm me one thing. Did you re -install version 11.
2. Re intstallation of version 11 has lot of issues ( atleast 11.1.1.1).
Sandeep Reddy Enti
HCC
http://hyperionconsutlancy.com/

Link template and database

I am creating a template from a existing document that uses a database thru php for it's contents. For some reason When I save it as template ( i chooce update link) It does not show the images. Also it does not create the link properly. A couple of things to note :
The image is called by a database field from image folder.
link is also called upon from a database field.
They both work fine in the document but when I create a template or another document based on template the link and image does not work . here are code from the template
<?php do { ?>
 <table width="800" height="38" border="0" align="center" cellpadding="0" cellspacing="0" class="tableborder2">
 <tr>
 <td width="637" align="left" valign="top"> 
 <?php echo $row_mainpage['title']; ?><?php echo $row_mainpage['other_info']; ?> 
 <a href="<?php echo $row_mainpage['../link_product']; ?>" class="pricevendor"><?php echo $row_mainpage['merchant']; ?></a> Price $<?php echo$row_mainpage['price'] ; ?> <?php echo $row_mainpage['price_note']; ?></td>
 <td width="163" align="left" valign="top"><li class="navigation3"> List Price : $<?php echo $row_mainpage['list_price']; ?></li> <li class="navigation3">Deal expire : <?php echo $row_mainpage['deal_expire']; ?> </li>
 <li class="navigation3"> Added: <?php echo $row_mainpage['date_created']; ?></li></td>
 </tr>
 </table>
 <table width="800" border="0" align="center" cellpadding="0" cellspacing="0" class="tableborder">
 <tr>
 <td width="150" align="center" valign="top"><a href="<?php echo $row_mainpage['../link_product']; ?>"><img src="image/<?php echo $row_mainpage['image']; ?>" width="125" height="125" border="0" align="left" /></a></td>
 <td width="650" align="left" valign="top"><?php echo $row_mainpage['description']; ?>
 <a href="<?php echo $row_mainpage['../link_product']; ?>" class="click">Click here</a> to shop for this deal 
 <?php echo $row_mainpage['shipping_info']; ?> 
 <?php echo $row_mainpage['tax_info']; ?> 
 <?php echo $row_mainpage['buying_instruction']; ?>
 </td>
 </tr>
 </table>
 <?php } while ($row_mainpage = mysql_fetch_assoc($mainpage)); ?>
 

You can use the templates for Oracle Enterprise Linux.
According to Readme:
"The oracle-rdbms-server-11gR2-preinstall package is installed in the templates
before the Oracle Linux 6 Update 4 templates. This package installs software
packages and sets system parameters that are required for Oracle single instance
and Real Application Cluster install for Oracle Linux Release 6.
This package creates the 'oracle' user, with an initial login group of 'oinstall',
a supplementary group of 'dba', and a home directory of /home/oracle. The
Oracle-validated package disables logins by the user 'oracle', and the password is
locked for the 'oracle' user by default. To enable the 'oracle' user account, log in
as the 'root' user to the guest virtual machine after it is booted."
If you choose to use OEL 6 Update 4 you can install the package using the package manager.

Display template family is not defined issue

Hi All,
We have gone live PT 8.52.16 yesterday, Users were facing issue with the CRM create case.
When user click on a button in a pagelet, it will open a create case component. In that its throwing display template id not defined.
Same user is able to work in another machine with out any issues. Both the machines has same IE 8 browsers + windows 7 machine.
We have only one display template family i.e) CRM_HHD.
Any reason why this is happening? Users who is having issue in accessing the create case in their machine were able to work on another machine.
Regards,
Hari.A

Its throwing error like "Display template family is not defined error" pops out for few users. At the same time its working for few users.
We could not find the exact issue why this is happening? is it due to app server cache issue?
We have heard back that few users saying it was not working for them initially and later it started to work.

Issue defining DN 7965 because using 7965 SD Phone button template on Cisco 7965 VoIP phones

I am having issue with assigning DN7965 to a phone device. Error message indicates that 7965 is already associated and in use. We have associated phone template 7965SD because most our phones are CISCO 7965. Is there a way to overcome this issue ?

Hello, All!
I have continued testing this in my lab and have come up with the following results.
When setting up a new device, TAPS will generate an error if the DN is already in existence across multiple devices.
If replacing a device, you must use the same model device or else TAPS will generate an error.
Unfortunately, based on the above rules, I was unable to utilize TAPS for bulk upgrade of user devices from 7960 model phones to 7965 model phones. However, I have come up with an alternate solution.
Note: This solution would only need to be used in a scenario where you do not want to assign a MAC address before physically deploying the equipment. The below solution provides the flexibility of creating the phone configurations prior to deploying the equipment without having to have all hardware specifically assigned to a user/DN.
Bulk Update Cisco Phones without MAC Addresses
Bulk Admin > Phone > Export Phones > Specific Details (Pull relevant information, DN(s), Description, Owner User ID, CSS, so on…)
Download the file, change to csv, open in Excel
Clear contents of “Device Name” field. Parse through and update other fields if needed.
Save a copy as CSV, upload to CUCM as Insert Phones > Specific Details
In CUCM, create a Phone Template for import
Bulk Admin > Phone > Insert Phones > Choose File > Choose Phone Template > **Important** Select Create Dummy MAC
Run Job
Once job is completed, all 7965 devices will be created with a BAT prefix and dummy MAC address, check Device > Phone to confirm
…When ready to activate
Device > Phone > Search by DN for BAT device
Open device, change MAC address to new 7965 hardware, check “Is Active”
Click Save.
Plug-in 7965 device to network. When the phone comes online and gets past firmware it will pull newly generated SEP config with user ext.
I hope this helps. I appreciate the communities continued assistance.

Button Templates in database not shwn in CUCM admin Phone Button Templates

Similar Messages

Maybe you are looking for