Buying old Airport Express of eBay - Do i need sellers' password?

Hi,
If i just bought an old Apple Airport Express (The one that actually plugs into that wall) on eBay, do i need to ask for the sellers' password to the Aiport Express in order to connect it to my current wireless network and use airplay to steam music? What im ultimetly asking is: If i get the this airport express and i dont have the password, am i out of luck? Do i even need a password to connect to the aiport ecpress?, or do i just use the password to my current wireless network?
Thanks, Riley

Perform a Factory Default Reset on the Express as follows to get the device back to new, out of the box settings.
Power off the Express
Wait a few minutes
Hold in the reset button first and continue to hold it in for an additional 9-10 seconds while you simultaneously plug the power back in to the Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light
The Express is now reset
If you are asked for a password, the default is "public" (without the quotes)

Similar Messages

Do I need an ethernet switch or new router for IP camera setup with old Airport Express

Hello,
I am trying to setup a third party Foscam IP camera to my network so that I can ultimately use it as a baby monitor, and am having some difficulty. I currently still have an old Airport Express (with one ethernet port only). This is preventing me from setting up the initial camera because I don't have another ethernet port to plug it in to on the router. I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?).
I am fairly sure however, that my ISP provider (comcast) only provides one IP for my account. Does this mean I would have to buy a new router altogether with more than one ethernet port on it or one with a WAN port? Would I, in this case, have to plug the modem into the WAN port on the router, and then the camera to one of the ethernet ports on the router?
I consider myself fairly tech savy, but when it comes to routers, IPs, LAN, WAN, etc. I get a bit lost. This has been creating quite a headache for me and any help would be appreciated! Thanks in advance!

I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?).
Sorry, but this won't work as the modem expects only a single device ... either a computer or a router to be connected to it. Unless your modem is actually a combination modem & router or gateway device, then you would need a different router to solve your networking problem.

HT5022 Airport Utility 5.6 does not fix the old Airport Express!

My old airport express does not work anymore - the Airport Utility 5.6 makes changes but after re-starting, the Airport Express cannot be found. Now I am forced to buy a new one. Not good (and sold out as many experienced the same apparently)

Do you get any sort of error message when you try to install, and if so what does it say?

Can I use an old Airport Express to extend the range of a new Airport Express?

Hi all. I have an old Airport Express 802.11g (First Gen?) that is starting to fade. Still works, but not what it used to be. So I am going to buy a new Airport Express. I'm not interested in the Airport Extreme.
Question: If I use the new Airport Express as my main wireless router, can I plug my old Airport Express into another room as an extender? In other words, with the old Express and the new Express talk to each other or will a new Express only allow extension with another new Express?
Thanks!

Sorry, but the old AirPort Express 802.11 b/g does not have a setting to "Extend a wireless network", so it cannot be used as a extender with the newer AirPort Express if you plan to connect wirelessly.
If you plan to connect the older Express using a permanent wired Ethernet cable connection, then it could be configured to provide additional wireless signal coverage in that manner.

New Time Capsule, new MacBook, old Airport Express and Airtunes

I intend to buy a new MacBook and a Time Capsule, and I still have an old Airport Express, without 802.11n. I intend to use this Airport Express just for Airtunes, maybe to connect to a printer as well.
Now I was wondering, even though the Time Capsule is capable of using the 2.4GHz and 5GHz bands simultaneously, the MacBook is only capable of using one band, right? So if I use Airtunes to stream music to my Airport Express, my MacBook would be forced to use the 2.4GHz band, thus slower Time Machine backups etcetera. Is this assumption correct?
Or will my MacBook send the Airtunes signal over the 5GHz band to the Time Capsule, which will send the signal over the 2.4GHz band to the Airport Express, thus not slowing down any Time Machine backups?

Martijn wrote:
Now I was wondering, even though the Time Capsule is capable of using the 2.4GHz and 5GHz bands simultaneously, the MacBook is only capable of using one band, right? So if I use Airtunes to stream music to my Airport Express, my MacBook would be forced to use the 2.4GHz band, thus slower Time Machine backups etcetera. Is this assumption correct?
I don't think so.
Or will my MacBook send the Airtunes signal over the 5GHz band to the Time Capsule, which will send the signal over the 2.4GHz band to the Airport Express, thus not slowing down any Time Machine backups?
Yes I think this is correct. At least it seems to me that this is the purpose of having simultaneous dual-band. The time Capsule can send or receive on both bands at the same time, or receive on one band and then send on the other.

How can I use my old AirPort Express?

How can I use my old AirPort Express (the one that plugs right into the wall without a power cable) to stream music to a stereo when I am using the new Airport Express? The AirPort Utility 6.1 will not recognize the old AirPort Express.

Apple does not make it easy for you to use an older device when they want you to buy newer devices.
See this link for tips on how to install a version of AirPort Utility on Mountain Lion that will allow you to configure your older Express:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html
This is not supported by Apple, so it is your decision on whether you want to move forward with this. It works fine for me, but I cannot guarantee that it will work for you, nor offer support if you have difficulty.

I am trying to find out if I can upgrade my old airport express from WEP to WPA2? If so, how do I do that?

I am trying to find out if my old Airport Express can be upgraded from WEP to WPA2? If so, does anyone know how to do this? I have a new PC for work reasons and I cannot get online with my WEP password. I realize now this is why my family and friends who bring PC's into the house cannot connect - I need WPA2 for PC, and besides, I should upgrade anyway as this is more secure than WEP. Thanks for any help!

Clone your system.
Install the 10.6.8 Java update.
Clone back from your clone you made before installing the update when finished.

Old airport express not recognized by airport utility

Mine is a two part problem. I was having issues with my old Airport Extreme Base Station. I was dramatically losing data transfer speeds just 20-30 feet from its location. I also noticed that signal strength no longer made it upstairs to the master bedroom. I thought that after 6 years, it finally died on me. I purchased a brand new Netgear dual band 5G router and performance improved but I still am having difficulty with the non-5G band upstairs. (I understand that 5G doesn't travel as far but is faster. I thought it would be better to use my other network for devices upstairs.) I still have the Airport Extreme and believe it or not, a really old Airport Express. I've tried to use both to extend the range of my non-5G network and have failed miserably at both. The Airport Extreme keeps giving me problems during set up to extend range and my Airport Utility doesn't even support the Express. (see photo)
Any suggestions?

Two separate issues here:
I still have the Airport ExtremeThe AirPort Extreme would not be compatible with a Netgear router if you are trying to "extend" or "repeat" the signal from the Netgear wirelessly.
The reason.....Apple designed their "extend" feature to only work with other Apple routers, so it would be extremely unlikely that this feature would work with a 3rd party router for the purpose that you ask about.
If you are able to permanently connect the Extreme to the Netgear router using a permanent wired Ethernet cable connection, then the Extreme could be configured to provide additional wireless coverage in that manner.
Airport Utility doesn't even support the Express. (see photo)
That would be correct if you have the older A1084 or A1088 versions of the AirPort Express. To confirm, locate the model number on the side of the Express.....hard to see....you may need a magnifying glass to see the number.
It will take a Mac running the older Leopard or Snow Leopard operating system, or a PC with AirPort Utility installed to be able to administer the older Express.
Unfortunately, this version of the Express does not even have an "extend" feature, to it too would also need to be permanently wired to the Netgear or the Extreme if you need more wireless coverage from the Express.

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

I have read all of the similar issues on this site and I still cannot connect my airport extreme (although there is no problem with my old airport express - help...

i have read all of the numerous and similar issues on this subject. and i still cannot connect my new airport extreme. my old airport express works fine still. help. and why are there so many issues with connecting this stuff? i thought this stuff was supposed to be getting easier, not harder... thanks.

Sorry, but I have no idea on what you have read and tried so far so please forgive me for any redundancy.
Is your AirPort Extreme the only router in your current network configuration? Which exact model is it? If there are other routers being used, please provide their make(s) & model(s). Also the make & model of your Internet modem.
What is your goal with the Extreme? Is it to replace the "old" AirPort Express? Will you still be using the Express for any reason(s)?

Old AirPort Express disappears

Using several AirPort Express points to stream music to different areas of the house. The old one disappears - believe this is ever since I upgraded to AirPort Utility 6. I get a message that this version of the Airport Utility does not support the old AirPort Express, then it disappears even though it appears to be connected to the network - I've been unable to stream music to it.
The original AirPort Express is pretty old, the second one is not quite 2-years old, and we just bought a new one (looks like a white Apple TV - having trouble connecting this one, but that's in another discussion).
Help!
larry   :-)
========

Thank you, the link was very helpful. I ended up setting up a new Airport based network using both v6 and v5 of AirPort Utility. Everything is working the way I wanted it to - except I didn't expect to have to set-up a second network.   Oh well.
larry    :-)
========

Iphone 3GS has "169..." IP address after replacing old Airport Express

My 3GS is no longer connecting to my home network after replacing my old airport express.
Previously my old G5 iMac would have problems connecting to the old airport express, BUT my iPhone 3GS would reliably connect.
After installing this new airport express, my iMac is on the network, but NOW my iPhone 3GS is experiencing the same problem my iMac previously had: IP address changed to 169.254.205.191
Airport Express is set to WPA2 Personal
Updated firmware on the Airport express
Network settings on iphone have been reset several times.
Airport express has been rebooted several times.
Please help. Thank you.

Thnx William but that is not the case coz all other devices(laptops, desktops, PS3...etc) r working just fine.
after alot of time trying to figure out what the problem is I figured out the problem but cant seem to sove it:
I have three router in my network one acts as a DHCP server (router 1) and the others act as AP, they all brodcast wirless (SSID) based on the internet connection coming from router 1, all devices including my old iphone 3g connect on all three router no problem and get assigned an ip address within range 192.168.1.~, however when i connect my 3gs to router 1 (DHCP) it works perfectly and connects to the internet but when I connect to any of the other routers I cannot have internet access and it takes a long time to show the wi-fi symbol (3 bars), I managed to overcome this by giving my second router another network IP i.e 192.168.2.~ and made it aother DHCP server (but another network) that way my 3gs connected just fine like the 1st router, the problem with this solution is that I am on two seperate networks but same internet feed so I cannot communicate between lapto, desktop, PS3...etc
I guess I have two options:
1- wait for an update for 3gs hoping this could be solved and keep my network as is.
2- assign three different networks just for 3gs to work and sacrifice my whole home sharing.
SOOOO Pleaseeeeee if anything know anything or could help me in anyway please and post, is it just me or have i heared alot of Wi-Fi problems with 3gs!!!

I have an old Airport Express. How do I get Airport Utility to recognise it?

I have an OLd style Airport Express that I was using with my 2007 iMac and Tiger. Recent upgrade to Mountain Lion.
How do I get the Airport Utility to recognise it so I can set extra stuff?
AndrewH66

Here are the AirPort Utility downloads:
http://support.apple.com/downloads/#airport
Bottom line: I don't believe it's possible to use your old AirPort Express with Mountain Lion. The current AirPort Utility is 6.3.1.
I'm assuming you have this one (from around 2004):
http://support.apple.com/kb/SP76
If instead you have this one (from arount 2008):
http://support.apple.com/kb/SP1
... then AirPort Utility may well support your device.

HT4259 I have the old airport express but my iPad 3 is not able to connect to it even with the app downloaded. What can I do?

I have the old airport express but my iPad 3 is not able to connect to it even with the app downloaded. What can I do?

Use a windows computer.. or ask a friend to bring a windows laptop and use the 5.6 version windows utility.

Old Airport Express Ethernet Port Usage

hi there
i have an older airport express (Model No A1264) bought some years back, it has only 1 ethernet port on it instead of 2 on the current model.
i understand the new model has 1 ethernet WAN port for modem, and the other LAN port for ethernet printer or computer.
my question is, the ethernet port on my old airport express is both WAN and LAN? or is it just a WAN port?
because i intend to get an airport extreme to hook up a optical fiber modem which will be located downstairs in my house.
and use my old airport express on the 2nd storey to hook up my etherenet printer, but not sure whether that ethernet port will work? or do i need to purchase the new model?
many thanks in advance

It no longer works.
Unplug the Express, let it rest a minute or two and plug it back it in.
Try a different Ethernet cable.
If still no luck, test the connection by temporarily connecting a laptop to the Ethernet port on the Express using an Ethernet cable that you know is working. Turn off the wirelss on lthe laptop for the "test" and see if you can get a good Internet connection that way.
If you can, you know that the Ethernet port is working, and you will need to focus your troubleshooting on the printer.
If you still cannot get a good connection during the "test", this indicates that the Ethernet port on the Express is no longer working, and the Express will likely need to be replaced.

Buying old Airport Express of eBay - Do i need sellers' password?

Similar Messages

Maybe you are looking for