By mistake i make the brightness on lighter and then its automatically dark iphone5 how i will reset

by mistake the brightness of my iphone 5 i make on lighter and then suddenly my screen is locked now my iphone is dark how i will reset

In settings/wallpaper & brightness try changing the auto brightness setting switch

Similar Messages

My macbook 15 inch wont turn on, it makes the hard drive sound and then a few seconds later it sounds like its powering down with like a clicking noise

my macbook 15 inch wont turn on, it makes the hard drive sound and then a few seconds later it sounds like its powering down with like a clicking noise

Try Resetting your Mac's PRAM and NVRAM
If that doesn't help, try Resetting the System Management Controller (SMC)
If neither helped, boot from your install disc, run Disk Utillity. The startup disk may need repairing.
Using Disk Utility to verify or repair disks
Check the S.M.A.R.T. status at the bottom of the Disk Utility window.
Make sure it says: Verified

Anytime I move my mouse my current window disappears. I move the mouse to the top left corner and then I comes back. How can I turn this off?

Anytime I move my mouse my current window that is open disappears. When I move my mouse to the top left corner it comes back. How do I turn this off? It's not a Zoom issue, it disappears completely. Help please.

Are you running 10.6 Snow Leopard as your profile indicates?
If so, it sounds like maybe an Expose or Active Screen Corners issue?
Go to Apple > System Preferences > Expose & Spaces > Expose and
1. experment with the Active Screen Corners selections
2. take a look at your F key settings for Expose
3. lastly check your Dashboard settings

The screen on my macbook has malfunction. When I change the brightness to zero and return to the first level of brightness it works briefly but then the screen starts to flicker brightness and quickly extinguished.

The screen on my macbook has malfunction. When I change the brightness to zero and return to the first level of brightness it works briefly but then the screen starts to flicker brightness and quickly extinguished. It seems to be a bad contact, it would not be normal for a quality product that should have, he has less than two years of use. Not because of the bad use or crash. Someone with the same problem or can help me? It's really a contact problem? I've done all the procedures recommended by the online support. Thanks.

Hey everyone in Apple world!
I figured out how to fix the flashing yellow screen problem that I've been having on my MBP! Yessssss!!!
I found this super handy website with the golden answer: http://support.apple.com/kb/HT1379
I followed the instructions on this page and here's what I did:
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
I went through the 6 steps above twice, just to make sure I got rid of whatever stuff was holding up my bootup process. Since I did that, my MBP boots up just like normal. No flashing yellow screen anymore!!
(Note that I arrived at this solution when I first saw this page: http://support.apple.com/kb/TS2570?viewlocale=en_US)
Let me know if this works for you!
Elaine

I'm not techinal so please bear with me. I don't have the bar that allows me to type in a website. I did have a few minutes ago. When I make the page full screen and move my cursor to the top of the page, the bar drops down and I can use it. help

I'm not techinal so please bear with me. I don't have the bar that allows me to type in a website. I did have a few minutes ago. When I make the page full screen and move my cursor to the top of the page, the bar drops down and I can use it. I've tried restarting my computer, didn't work. Help!

Well I figured it out, right click the arrow that makes the screen bigger and unclick the Hide Toolbar. I knew it couldn't be that hard.

The operation can't be completed because some items had to be skipped. For each item, choose File Get Info, make sure "Locked" is deselected, and then check t

The following error comes up when I try to install the updated Firefox:
"The operation can’t be completed because some items had to be skipped. For each item, choose File > Get Info, make sure “Locked” is deselected, and then check the Sharing & Permissions section. When you are sure the items are unlocked and not designated as Read Only or No Access, try again."
When I follow the instructions in the error message, it shows that my user name has read and write access. There are a couple other items that are read only. I tried to change this to read and write, but the Sharing and Permissions options are greyed out and will not let me change them. What is the work around for this? I would really like to install the new firefox.
Thanks.

Hello,
Certain Firefox problems can be solved by performing a ''Clean reinstall''. This means you remove Firefox program files and then reinstall Firefox. Please follow these steps:
'''Note:''' You might want to print these steps or view them in another browser.
#Download the latest Desktop version of Firefox from http://www.mozilla.org and save the setup file to your computer.
#After the download finishes, close all Firefox windows (click Exit from the Firefox or File menu).
#Delete the Firefox installation folder, which is located in one of these locations, by default('''This will NOT delete profile info such as bookmarks and history'''):
#*'''Windows:'''
#**C:\Program Files\Mozilla Firefox
#**C:\Program Files (x86)\Mozilla Firefox
#*'''Mac:''' Delete Firefox from the Applications folder.
#*'''Linux:''' If you installed Firefox with the distro-based package manager, you should use the same way to uninstall it - see [[Installing Firefox on Linux]]. If you downloaded and installed the binary package from the [http://www.mozilla.org/firefox#desktop Firefox download page], simply remove the folder ''firefox'' in your home directory.
#Now, go ahead and reinstall Firefox:
##Double-click the downloaded installation file and go through the steps of the installation wizard.
##Once the wizard is finished, choose to directly open Firefox after clicking the Finish button.
Please report back to see if this helped you!
Thank you.

My husband uses adobe cs5. The clone tool isn't working and after resetting the tools adobe bridge now goes to picasa. How can we make the clone tool work and have bridge go to cs5 not picasa?

My husband uses adobe cs5. The clone tool isn't working and after resetting the tools adobe bridge now goes to picasa. How can we make the clone tool work and have bridge go to cs5 not picasa?

A lot more information about your hardware and software is needed.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CC", but something like CC2014.v.2.2) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
a screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

HT4897 I created an alias precisely because I wanted to make it the new default name and then quickly realized it wasn't possible. How long after deleting the alias will it become available again so that I can create a new account with it?

I created an alias precisely because I wanted to make it the new default name and then quickly realized it wasn't possible. How long after deleting the alias will it become available again so that I can create a new account with it?
I'm trying to make iCloud mail my primary email but I'm concerned that I may have lost the perfect email address forever.

I have the same problem. After our wedding I've created an alias ([email protected]) to my actual AppleID Account ([email protected]). Now I'd the idea to delete the alias and my actual AppleID to create a new AppleID with ([email protected]).
Is there really no possibilty to do this?
Thanks in advance for quick and positive feedback.

Why is the brightness of my iMac become 100% automatically when I turn on..

Why is the brightness of my iMac become 100% automatically when I turn on my computer even though I set the brightness to the lowest before I shut it down.
I want to set the brightness to the lowest every time I turn on the computer automatically.
Is there anything I can do?

Hi,
There seems to be a serious issue with screen brightness on the 24" iMac. About 6 days ago I bought a 24" iMac (2.66 Mhz model w/4 GB RAM + 640HD).
Out of the box it had Leopard 10.5.5 installed; there were several problems.
1. Screen brightness was way too BRIGHT. Display preferences would not pull brightness down. At least not down far enough so that the screen could be viewed without extreme discomfort. Plus add insult to injury a reboot would reset the preferences to maximum brightness. NOTE: An upgrade to 10.6.1 did NOT fix the issue.
2. Viewing a browser page via either Safari or Firefox (latest versions of each) was not good. A vertical scrolling would be jumpy and appear pixelated. Upgrade to 10.6.1 seemed to fix most of the issue in Safari, but Firefox was still not working properly. The issue appeared like a horizontal "ripple" in about the bottom 2/3 of the browser window. The effect did NOT extend outside of browser window. Changing screen resolutions did not work.
3. Connecting a USB Logitech head set caused issues with Sound preferences.
If the head set was connected during startup the machine would recognize them as main sound. The internals speakers did NOT appear in the Sound preferences. as an optional choice. Removing USB headset and reboot would return the internal speakers to the Sound preferences. Plugging in headseat would work for a while. We could repeat and same problem would occur.
These are all in 10.6.1 - definate bugs.
Returned with the iMac to the Apple store. Bottom line, after nearly three hours; the Apple technician, and everyone could see what we were talking about.
Regarding the screen brightness. Nothing they could do about it. They stated that "not too many people have complained about it, to their knowledge." They stated that the electronics in the "florescent" panel could not be turned down the same way. TRANSLATION: The programers at Apple let this one slip past them. As a customer (software programmer & network analyst) I expected a bit more of an intelligent answer.
However.
Examining the 20" model I noticed that we could turn down the screen brightness - at least to a level that my wife and I could live with. PLUS the settings remained after a restart. Something that was NOT happening with the 24" model.
So - we exchanged the 24" for a 20". Frankly we are a LOT happier. The Safari/Firefox issue is still carried over to the 20". However it is not nearly so noticable on the smaller screen.
Plus the USB headset did not cause the same Sound Preference issues.
So - Thanks for the speedy return/exchange of the iMac. But someone needs to look at this from the programming side of things.

The internet updated without me knowing and now i can not pull tabs down to make a new window or change the order of tabs and i can't find out how to get back

my mozilla updated without acknowledging me first. I open it and I come to find out I can not move the tabs over to the right or the left one spot or two spots they just won't move unless I close them. I use to be able to move there anywhere i wanted or pull down and it became it's own window. Now I have to right click to make it a new window and then I can't drag and drop other tabs into it to make a window with several tabs. How do I get this back to the way it was before?

In case one of your extensions is involved, could you test the page in Firefox's Safe Mode? That's a standard diagnostic tool to deactivate extensions and some advanced features of Firefox. More info: [[Troubleshoot Firefox issues using Safe Mode]].
You can restart Firefox in Safe Mode using
Help > Restart with Add-ons Disabled ''(Flash and other plugins still run)''
In the dialog, click "Start in Safe Mode" (''not'' Reset)
Any difference?
''Note: on the new menu, Help is the ? icon toward the bottom.''

HT4759 How can make the events listed in my chalenda become automatically a reminder in the reminder?:

How can make the events listed in my chalenda become automatically a reminder in the reminder?:

Welcome to the Apple community.
Calendar and reminders are two different and separate apps, you cannot transfer information between the two of them.

How make the Top-level Navigation and Content Area in one page as a whole?

I want to make the Top-level Navigation and the Content Area in the one page as a whole displayed in user interface.In the default framework,the Top-level Navigation and the Content Area were contained in 2 pages, So the vertical scroll bar could only control the Content Area. I want to control the full page with one vertical bar like the page of "www.sdn.sap.com" Web.

Hi Jianguo,
One advantage of the external facing portal solution (SP14) is that the framework page is displayed in a single frame. Perhaps this could be of use to you.
Hope this helps.
Daniel

HT1349 hi Mmm ive been told that installing linux on mac book pro retina 15 and even others and using it as my first sofware will make the mac heaqt up and burn from inside!!!!! true??????????

hi Mmm ive been told that installing linux on mac book pro retina 15 and even others and using it as my first sofware will make the mac heaqt up and burn from inside!!!!! true??????????

Hi shldr2thewheel,
it has been a while since we have last spoke, I would like to let you know, I am still working on getting used to the switch from windows to a Mac/Apple system. I do have a new question for you, I did purchase In Design CS5.5 through journeyed.com through Cuyahoga Community College of which I attend as a student, is there a way to purchase an online book through iTunes to learn that as well? Also, you know me, the struggling student, I would also, when and if the book can be purchased through the iTunes, would need to know if you do know of a much easier book for struggling students like myself and at a reasonable price as well for the In Design CS5.5 program. Our campus bookstore had closed early, and, so did the colleges library and our local library here where I do live, so, I cannot go to either place to purchase a book or to take out a book, plus cash funds are low at this moment as well but, I do have money left on the iTunes account to use, if it can be used. So, can it be used, the iTunes money, towards finding a low priced online book? I am in great need of assistance as I have a project due for my one course for this Tuesday, September 4, 2012.
Sincerely in need of help once again,
Kim

Hi Mmm ive been told that installing linux on mac book pro retina 15 and even others and using it as my first sofware will make the mac heaqt up and burn from inside!!!!! true??????????

hi Mmm ive been told that installing linux on mac book pro retina 15 and even others and using it as my first sofware will make the mac heaqt up and burn from inside!!!!! true??????????

hi Mmm ive been told that installing linux on mac book pro retina 15 and even others and using it as my first sofware will make the mac heaqt up and burn from inside!!!!! true??????????

I created a new collection and put all of my same photos in them as a previous collection, then I changed them to black and white and both collections changed. How do I keep the first collection colour and make the second collection black and white.

I created a new collection and put all of my same photos in them as a previous collection, then I changed them to black and white and both collections changed. How do I keep the first collection colour and make the second collection black and white.

For the second collection, choose the option to make virtual copies. Then you can turn the virtual copies to black & white, leaving the first collection in color. If you want file copies of the B & W images you can export copies.

By mistake i make the brightness on lighter and then its automatically dark iphone5 how i will reset

Similar Messages

Maybe you are looking for