C-220M3 RAID controller

Hello,
Cisco people has told me C-220M3 has to mandatory bring a RAID controller in it if you configure one HDD...actually Dynamic Configuration Tool doesn't let me configure a C220M3 server with one HDD if I don't add a RAID controller. I'm trying to find a technical explanation for that...as I recall, the old C-200M2 can be configured with one HDD and without any RAID controller at all, and that doesn't pose any problems.
Any inputs on that?
Thanks,

Hi Dani,
the C200 server has a in-build RAID controller which you could use. However on a C220 there are no similar integrated modules available and you need to choose either a mezz or a PCI (LSI) RAID controller for RAID configuration.
here is the chapter from the configuration guide:
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/raid.html
Thanks!
./abhinav

Similar Messages

RAID controller on G4; problems... is RAID dead? Help please!

Hey.
Here's the deal... Our graphics department has a MAC G4 (fully upgraded. newest patches, OS, etc.) that's got a 4 port SATA RAID controller. They use this with four 750GB hard drives as an external RAID (the OS is on a seperate, 65GB hard drive). The way it's set up, through Apple's OS, is we have the four 750GBs in pairs... those pairs are striped, and then the two sets of striped 750s are mirrored. This has worked just fine for a number of months, but we recently had a power surge, and now we're unable to mount "Monkey" (the name of the 1.4TB array).
See the below screenshots for more clarification.
http://www.amcdoors.com/lorenzo/raidsetup.JPG
This shows the RAID card, and the four SATA cables coming out of it.
http://www.amcdoors.com/lorenzo/leftside1.JPG
As you can see in this and the below screenshots, this shows the 1.4TB Striped set as 'online', but the two below (the two 750GB hard drives) show up as "offline".
http://www.amcdoors.com/lorenzo/leftside2.JPG
this shows the actual drive i click on. same thing
http://www.amcdoors.com/lorenzo/leftside3a.JPG
If i click the entire array, you can see how it's set up (the Mirrored RAID set consisting of the two Striped RAID sets). The RAID sets (all 3 of them) are showing up as online, yet the drives are offline. No idea why. The drives are all powered, and are spinning, and plugged in.
http://www.amcdoors.com/lorenzo/leftside3b.JPG
when you click "Monkey Drive", nothing shows up in it. i don't remember if anything ever used to. if you click 'mount', nothing happens.
http://www.amcdoors.com/lorenzo/leftside4.JPG
http://www.amcdoors.com/lorenzo/leftside5.JPG
this shows the exact same problem as the first RAID set.
http://www.amcdoors.com/lorenzo/verifyRAIDset1.JPG
If you try to Verify the RAID set, it shows that no repairs are necessary
http://www.amcdoors.com/lorenzo/verifymonkey.JPG
If you try to verify Monkey, you get a "Volume Needs Repair" error... but when you try to repair it, you get this:
http://www.amcdoors.com/lorenzo/repairmonkey.JPG
Really need help; this is a pretty critical problem. Someone that's familar with RAID solutions on MACs please help me out. We can't risk losing any data if at all possible.
Thanks
~Lorenzo

have you gotten this to work yet ?? if not let me know
-d

Hard drive configuration with Promise Raid controller

I plan on running two 30 gig 75GXP drives on the Promise controller in Raid-0 mode. I also have a 60 gig WD drive that I use for backups and for initial installation. During installation, I put the Win98SE setup files and all the drivers, apps, backup data, etc. on the WD drive and do a clean install from there.
My current (old) board is an Abit KT7-R with the Highpoint raid controller. Using the Highpoint controller, I am able to put the WD drive as a slave device and the controller treats it as a normal IDE drive. I'm moving to the 845 Ultra ARU. From what I've read, if you put a single drive on the Promise controller, it tries to set it up as a Raid drive? I don't want to risk losing my backup data on the WD drive to some attempt by the Promise controller to "raid" my single drive. So, where is the best place to put my WD drive so that I can install my system from it? I'm thinking about putting it as Master on IDE2. I normally run my CD as Master on IDE1. Once the installation is complete, I will remove the installation files from the WD drive and use it exclusively for backups. I have the WD drive in a Vantec EZ-Swap rack, and I normally keep it powered off unless doing a backup.
So, the plan is to create the Raid-0 array, Fdisk and format the array, and then load Windows from the WD drive, followed by all my applications. Is Master on IDE-2 the best solution for the WD drive?

hi
not very clued up on raid but it sounds right
if the wd drive is on its own on that ide do not jumper
as master you have to have no jumpers if all alone

Unknown Raid 5 Array after Raid controller replaced

Hello,
I had a raid controller fail during the week, and after shutting the xraid down and installing the new controller, all the drives in the array are now amber.
In Raid Admin 1.5 the array does not show up, only all 6 member drives with an amber warning and 'Type: Unknown Array'.
I used the 'Recognize Array' utility to try and fix this, however whilst each drive shows as being recognized as being part of a Raid 5 set, it will not recreate it.
Am I completely screwed? or is there some other way to get this to repair/recognize?
Any tips would be greatly appreciated.
Thanks
Mark

Due to time restrictions on getting the xraid back online, had to recreate the raid and restore data from backup.
No fix found.

G5 Xserve Harware RAID controller - do all drives have to be connected?

Hi,
I am installing a hardware RAID controller into a G5 Xserve. The machine has three drives in it - one 80 GB drive module that has just the operating system installed on it, and two 500 GB drive modules that are currently configured as a RAID 1 array via software. I am aware that I have to reformat the drives after installing the RAID controller, and I have taken appropriate steps for backing the data up. My question, however, is if I will have to attach all three drives to the RAID controller, or whether I can leave the 80 GB module separate (the preferred configuration). Thanks.

Watch out for the firmware bug on the Apple Hardware RAID - doesn't always fully flush write caches on graceful power down (disconnects from the drives before the caches are fully flushed). I turned in a RADAR bug report in November 2005 (RADAR # 4350243), still open. It was a very difficult bug to pin down and create a reproducible test case - causes mystery garbage blocks from space, especially hard to get reproducible results because of the way RAID 5 works on reads. LSI Logic fixed this bug after Apple's code split from the LSI firmware code (the Apple Hardware RAID card is a rebranded LSI Logic megaraid card with Apple firmware), but it seems unlikely that Apple will ever fix this bug because the Xserve G5 and Apple Hardware RAID card are both EOL.
Only known workaround of which I am aware is to disable write cache on all LUNs.
Russ
Xserve G5 2.0 GHz 2 GB RAM Mac OS X (10.4.8) Apple Hardware RAID, ATTO UL4D, Exabyte VXA-2 1x10 1u

Shopping For A RAID Controller

I have seen the Areca brand name on here many times, so I assume they are the best for what we do. But, there are so many models that I have no idea what to look for. I probably won't ever have more than 4 or 6 storage drives plus an SSD system drive. Maybe a couple of external drives and an NAS.
If I have Windows 7 64-bit
i7-2600k processor
ASUS P8P67 Pro motherboard
32 GB RAM 1600
GeForce GTX 580 Amp! from Zotac
AX850 PSU from Corsair
Every component is reasonably fast, bu I am sick of the senseless limitations of this mootherboard. My drives are aging so they need to be replaced.
Which specs are important for video editing? Which brand and models are most popular and shoould I wait for some new release?
Another thought - If a RAID controller is over $400 US, Is it more cost-effective to upgrade to a more capable motherboard/processor with all the ports I need?

What to look for
Brand
Areca or LSI
Ports
8 or more
Card
PCIe-3.0 8x
Cache
512 MB or more
Multi-lane
SFF-8087/8088
Examples
Areca ARC-1882 series or LSI MegaRAID 9285
Warning: You have to realize that on your motherboard adding a dedicated raid controller will entail that your video card will throttle down from PCIe-16x to PCIe-8x mode, resulting in a 10 - 15% performance penalty, due to limitations of the chipset. A dedicated raid controller, especially with around 6 disks always outperforms an on-board raid by a wide margin. To see some benchmark results, look here: Reflections
To see what meets your requirements, also consider the raid level you want to use. If raid3 or raid30, then LSI is out. You can check out what controllers are popular here: Detailed Results but you have to be registered and logged in to access the page.

"Waiting for RAID Controller F/W to become ready..."

Hello
Lately I have been getting this message more often than not -- before Windows 7 (not) booting: "Waiting for RAID Controller F/W to become ready..."
Any suggestions?
I have a
Areca ARC-1680D-IX 12-ports SAS RAID
Thanks
Rowby

We sell and use these now:
http://www.intel.com/products/server/raid-controllers/RS2BL080/RS2BL080-overview.htm
http://www.intel.com/products/server/raid-controllers/RS2PI008/RS2PI008-overview.htm
But they have more here: http://www.intel.com/products/server/raid/index.htm
They also use LSI chips like Areca and Atto.
Eric
ADK

K8N master2-far doesn't detect Areca 1220 raid controller

Today i purchased the last components for my system. Everything works perfectly except for my Areca 1220 8x pci-e raid controller. As i feared the controller is nowhere to be seen, not in the bios, not in windows. I already had bios version v1.10 but flashed the bios version on the msi site anyway. Nothing changed. On the msi site under "QVL" i see my Areca at the bottom of the list. Does that mean that this MB can work with this controller? What must i do to make it work? I think i have to see it at least in the bios!
Your help is appreciated. Now 5x 300 GB of storage is doing nothing.

Quote from: Bas on 10-November-05, 20:30:00
Maybe you need to update the cards firmware.
I already looked into that matter and found out that the only way to upgrade the firmware or bios is to use their http tool McRAID Storage Manager. This of course is done in windows. Now windows doesn't see my Areca 1200 and so McRAID doesn't see it either. I can't update my Areca.
This problem is well known by the motherboard manufacturers. Let me quote something from the Areca site:
Q10150407 - Is there any socket 939 motherboards that work with your model ARC-1210 raid controller? In a SLI board I would use one 16x slot for Graphics card.
Our PCIe ARC-12xx series controller uses Intel IOP332/333 processor. The Intel high performance IOP (IOP331/332/333) has integrated the bridge chip in the controller. But the original NVIDIA nForce4 SLI chipset BIOS has the problem after Bridge IRQ routing. All controllers use Intel new IOP 332/333, such as Areca, Intel, and LSI have the same IRQ routing problem. Those NVIDIA 939 M/Bs can be worked in the Windows environment. Due to the Windows system takes over the BIOS job, and Linux & FreeBSD need to use the M/B BIOS, so it has problem with our PCIe controller.
Currently, DFI, Ausu, MSI and Gigabyte have BIOS to solve the problem. If you have problem in this kind of mainboard, please try to manufacture latest BIOS.
We have tested DFI Lanparty NF4 SLI & ASUS A8N-SLI Deluxe, and Asus A8N-SLI Premium. It works very well with our firmware 1.38 and newest mainboard BIOS. Try to swap the graphic and our controller, if you find some warm boot problem in the Asus A8N-SLI Premium.
I still think i need an updated bios for the k8n master2-far (ms-9620). The fact remains that there are problems reported with every SLI motherboard. I knew this already from the socket 939 platforms. I was sceptical about the k8n master2-far but thought that a server MB should have no problems. I did ask a question about this however at the shop where i bought this MB. I even found an reply from you to another user who had similar concerns about the Areca controllers and an SLI MB. You said that it should not be a problem. Even so i always kept the possibily open that this problem can happen. And here i am
Thanks for your help. More input is always appreciated as i am still waiting for an answer from MSI in the Netherlands about this problem. Right now my server is doing nothing. I hope my raid controller will work very soon.

Solaris 10 on an HP DL180 G6 server with P410 Raid Controller.

This is an informational post to try and save people some of the pain that my colleague Joe and I have just gone through to get Solaris 10 installed!
The DL180 G6 is an interesting box. It uses the latest Nehalem processors, and can support up to 12 x 3.5" old school high density 15k RPM drives. This is pretty unique in the industry. However, here is what you need to know -
- The P410 raid controller must have memory if you want to present all 12 drives down as JBOD to solaris to be managed via ZFS. i.e. order the P410/256. If you order the P410/ZM you will only be able to create a maximum of 2 arrays which will be seen as disks by Solaris.
- The P410 requires a driver that doesn't exist on the DL180 G6 driver page at HP. If you look under the DL585 G6 page you will find the solaris driver you need. [HP DL585 G6 storage driver page|http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=3949980&prodNameId=3949981&swEnvOID=2023&swLang=13&mode=2&taskId=135&swItem=MTX-f490e7c0f736457c92229f7e8c]
- The network card is a NC362i. This is intel based and referenced by this Solaris patch - [patch ID = 138175-02|http://sunsolve.sun.com/search/document.do?assetkey=1-21-138175-02-1]. The latest solaris 10 release (u7) doesnt contain the drivers for this card. You will have to add this patch separately. When added and recofigure rebooted etc etc, the device can be plumbed as igb0.
Hopefully this helps someone out!
Edited by: foobar50 on Jul 31, 2009 8:27 AM

Hi, try this out - it helped me some time ago:
http://forum.java.sun.com/thread.jspa?threadID=5081926
HTH,

Cannot boot with Perc /2 raid controller

I have just built a system with K7D + 2 2400 MP, and the system hangs when I try to boot with my Perc/2 raid controller in. I have stripped down to just the following components;
2 2400 MP
Perc 2
1GB ECC ram
Sapphire ATI Radeon 9000
When I try to boot the machine it gets as far as trying to load the Perc /2 Bios and hangs.
The Perc works fine in my old system Tyan Tiger 133 with dual 733 PIII, it also seems to boot up fine in a Tyan Tiger S2460.
Any ideas on the cause or a work around?
Thanks.

Yeah, all the firmware & bios is up to date, have stripped things down to just the motherboard, graphics card & Perc. Tried PCI graphics to elliminate any conflicts there. I have disabled all the on-board controllers too.

"Update for raid controller firmware" in availabel system upgrade does not go away after upgrade

We have two Ironport WSA, one S360 and one S370. Both stil have the "Update for raid controller firmware" still listed in "Available upgrades" even though we have done the update and rebooted the appliances.
How can we confirm that the update is applied?
If it is and the notice is still there how do we get rid of the reminder?

Go to the command line of the appliacne and run "version"
That will show you the current version of the firmware.
If you have record of what was there, you can compare...
Otherwise contact TAC, they can verify that you have the up-to-date version and pull your serial from the distribution list so you don't see it any more.
Ken

On-board RAID and PCI RAID controller

Hello everybody,
I am new to the forum. So, please excuse me if that topic was already covered...
I have MSI MAX2-LR (MS-6398E) board. It works just fine, no problem so far. Though I have 2 problems with add-on cards:
1. I was planning to use on-board RAID and additional PCI RAID controller = FastTrack 100 TX2 to cover 6 hard drives into 2 mirrored sets: 4drives one and 2 drives the other.
It doesn't work! I can use either on-board RAID or PCI RAID. As soon as I have any drive connected to on-board RAID, the PCI RAID disappeares. If I have no drives connected to on-board RAID, I can see both RAID controllers, they have different I/O and IRQs, and PCI RAID is working just fine. If only I connect one drive to the on-board RAID, it gets activated on startup, and the other one disappeares. :O
I believe it's a BIOS bug. I wander, if that can be fixed easily????? :D
2. I have a new Matrox Video card = Parhelia. It doesn't work in AGP slot! System doesn't recognize it, and beeps non-stop. I am dealing with Matrox Tech Support on that matter. ?(
Maybe, it's a known issue, and somebody can save me time by telling what's that about.
Appreciate any imput. Have a great weekend.!!! :]

Hey I also have the same Raid card and also the Matrox Parhelia, and I see that you also have some problems with the card I got also problems with the card, but they couldnt help me at theire forums (http://forum.matrox.com/mgaforum/Forum10/HTML/005085.html), I hope we have got more luck here :D

Hi, we have a G5 Blade server running OS X 10.5.8 with a dual Fibre Channel card. The OS does not read the card and cannot establish connection to the RAID controller. I have tried to move the card to another port with no luck. Ran all the updated softwar

Hi, we have a G5 Blade server running OS X 10.5.8 with adual Fibre Channel card. The OS does not read the card and cannot establishconnection to the RAID controller.
I have tried to move the card to another port with no luck.Ran all the updated software possible. Please can someone advice

Hi,
Was the card previously working in that machine? If it was and you have a G5 tower you could try the card in there. Here is a list of Apple fibre cards and cables which show what's compatible with what. http://support.apple.com/kb/HT1769
The card should appear in the System Profiler under Fibre Channel and PCI Cards.
All the best
Beatle

RAID Controller for V890

Hi,
I was wondering if anyone can tell me whether there is a RAID controller available for V890 for its internal FC-AL hard disks. I've never seen a RAID controller for FC hard disks and my vendor claims that there is no RAID controller available for the V890. So many hard disk slots & no RAID controller doesnt seem like the best of ideas. Software RAID just doesnt cut it when u apply RAID 5 on this number of hard disks.
Regards

Hello There,
There is no RAID Controller available to be used internaly for V880/890.

KT4 Ultra (6590) need update of the Promise SATA RAID Controller PDC20376

The last Bios update AMI 1.4 for the KT4 Ultra (6590) have built in the bios version 1.00.0.18 for the PDC20376 (Promise 376).
I can configure 2 maxtor (6E040T0) sata1 in a raid0 array and it works under WinXP SP3,
but the 2 drives are working in UDMA5 according to the FastBuild Utility when the motherboard specifications talks about 150Mb (SATA1).
It's not an OS problem because the FastBuild Utility at Bios startup show the UDMA5 mode for HDD.
It's not a Maxtor 6E040T0 (SATA1) problem because have no jumper to set.
The Promise support center don't provide support for built in raid controller but the responce was that it's related to a known bios issue of the controller, so i have to update.
For the last Bios version for the S150 TX4 controller look at:
http://promise.com/support/download/download2_eng.asp?productId=108&category=all&os=100&go=GO
It's impossible to update the bios with the promise tool because the controller is integrated in the motherboard.
I read for example than on the motherboard K7N2 Delta-ILSR the bios version of the Promise 376 controller is 1.00.0.21:
https://forum-en.msi.com/index.php?topic=92756.msg665966#msg665966
I think the only solution is a modding bios, where i have to replace only the Promise controller bios but:
1) The tool amibcp.exe can't open the A6590VMS.140 AMI bios (renamed .rom), i don't know why!!!
2) What promise controller bios rom file is good?
Can anyone out there help . . . please ?

This is my results compared to my other UDMA6 HDD on IDE1, HDTach long bench stop with "Read Error" and only quick bench works.
The version of the Controller driver under WinXP-SP3 is 1.0.1.29 and I configured the driver in the PAM Utility with:
"Driver Write Cache" enabled and "Write Back" as cache settings (The 2 Maxtor SATA1 in RAID have 2MB of cache, but i don't know How many cache have the controller!!).
The Burst Speed is too strange!!! quick bench error?
I made it so your image is clickable.
-Frankenputer

C-220M3 RAID controller

Similar Messages

Maybe you are looking for