C160 couldn't open after firmware upgrade

Hi,
We have a problem with our ironport C160 product. When we power on the device, it is starting its services and replies pings you can see from (1).
After that, it doesn’t ping no more and web page couldn’t open. For testing this issue, I connected a console cable to the device from its serial port. It starts asyncos services, then gives an error like (2)
Last night, I upgraded its firmware. It took approximately 2-3 hours and when upgrading process finished I rebooted the device. After I opened and saw the new version installed, I shut down the device from CLI.
Today, it couldn’t open. What can it be originated from and how can we solve this problem?
Thanks,
Mehmet.

Hi Mahmet,
Good to know that the C160 is now working.
Maybe you can check the hard drives stataus from System status or run 'version' from CLI.
You can also log a support case for IronPort engineer to look into what could have caused the system interuption if you wish.
Thanks,
Donny

Similar Messages

Iphoto wont open after system upgrade and iLife install

I installed Leopard and reallized i had to also buy iLife because the old version of iphoto was not supported by the the new operating system. Installed iLife and everything works exept iphoto. It acts as though it is "loading library" and then a pop-up window shows up saying:
"The photo library needs to be upgraded to work with this version of iphoto. Your photo library will not be readable by previouse versions of iPhoto after the upgrade. The upgrade process may take several minutes depending on the number of photos in the library."
I have hit "upgrade". But it still does not open.
I have about 9000 photos saved on an external drive.
I have repaired permissions as well as trashed iphoto and re-installed.
I read similar posts and am tempted to create a new library with library photo manager but am affraid i will lose some of my pictures.
I should include that because I couldn't open after the os update, I went into the my photo folders through finder and added new pix that I needed to get off of my camera. I've sinced trashed those folders.
Any ideas?
THanks in advance.
x

Welcome to the Apple Discussions. Thanks for the heads up on the out of date screenshot of BatChmod. It's been updated now. If all you your efforts to get your library updated and running fail you might try rebuilding the library with iPhoto Library Manager. It creates a new library based on the data in the AlbumData.xml file and leaves your current library untouched. Here's how that would work:
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 -Download iPhoto Library Manager and launch.
2 -Click on the Add Library button, navigate to your User/Pictures folder and select your iPhoto Library folder.
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File->Rebuild Library menu option
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be untouched for further attempts at fixing or in case the rebuilt library is not satisfactory.
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've created an Automator workflow application (requires Tiger or later), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 6 and 7 libraries and Tiger and Leopard. Just put the application in the Dock and click on it whenever you want to backup the dB file. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.
Note: There's now an Automator backup application for iPhoto 5 that will work with Tiger or Leopard.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Safari Crashes on Opening after Lion upgrade!

I just upgraded to Lion, and I try to open Safari, but it crashes before it loads my homepage!
I had recently set my default browser to Chrome in Snow Leopard the other day pre-upgrade, could that have something to do with it?

I'm using SL and found the perfect solution. 1) Follow oh_okay 's instructions, 2) download and reinstall Lastpass, 3) Restart Safari 5.1 and all should work fine. With this lastest update to Safari Lastpass functions a bit differently, having it's own tool bar with the option to hide. You have to click on the grey star, which stays grey, when logged in. There may be a tweek for that, which I haven't gotten to yet.
oh_okay
Level 1 (0 points)
Re: Safari Crashes on Opening after Lion upgrade!
Jul 20, 2011 10:31 PM (in response to Amgreen)
I've actually just found a solution.
As it turns out, LastPass was causing my crashes, too.
I had to find my SIMBL folder (~Library/Application Support/SIMBL/Plugins/LastPass.bundle) and remove the LastPass plugin.
After that, all was well. Not sure if I need to reinstall LastPass now or just pay for (what I've heard is the far superior) 1Password.

Email links won't open after ipad upgrade to 7.0.4, any help?

Web links in my emails won't open after ipad upgrade to ios 7.0.4, Any help with this issue would be appreciated.

Have you tried restarting or resetting your iPad?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after It shuts down, press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds).

IMessages won't open after Mavericks upgrade

iMessages won't open after I upgraded to Mavericks. I keep getting prompted to "enter the keychain password," but I never created a keychain. I never used it before the upgrade, and I skipped the step during the upgrade because I did not want to use keychain and it was an option to skip it during set up.

HI,
The OS X Mac have been using Keychains for a long time.
In the Applications/Utilities folder open Keychain Access.
This should show you at least two keychains.
The Login one for your Mac User account and the System one.
Generally speaking the Keychain keeps the passwords used by various apps and it needs to be Open.
In most cases the Login password for the Mac Account user is also the password that opens the Keychian when the computer is started up.
As each Mac User Account owns it's own Keychain there can be issues when you drag an account from one computer to another rather than using Migration Assistant.
i.e. you might Own it on one computer but not on another.
In the Finder > Go Menu hold down the ALT key and select the Library that appears.
In the library navigate to Keychains.
Click to highlight the Login one.
Now use the CMD and i keys together (Get Info)
At the Bottom unlock the padlock
Highlight the name that has (me) next to it (it should be your Shortname).
Once you have highlighted this use the cogwheel item at the bottom.
This should be greyed out but saying "Make you (Me) the Owner."
You should also have Read and Write permissions like in the Pic.
8:48 pm Sunday; December 29, 2013
 iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

HP 5524 Wireless does not work after firmware upgrade

HI,
I have just purchased an HP5524. After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully.
However, ever since wireless will not work. Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum. The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
Thank you

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Picture gallery not opening after OS upgrade

I recently bought blackberry z10 and up graded the OS to 10.2.0.424. After the upgrade I see that Picture gallery doesn't open. I tried rebooting the phone by pressing both volume keys simultaneously, but the phone won't reboot as well. Please help.

gauravrjpl wrote:
I'm sorry for not specifically mentioning the process followed. By soft reboot I meant the method you mentioned for BB10 devices. And hard reboot was pulling out the battery. What I couldn't do was to reboot using the volume keys.
Ah, OK...thanks!
gauravrjpl wrote:
Anyway, you mentioned about clean OS reload. Can you please elaborate? Can I do it myself?
Yup. For the "normal" method (automated, controlled by your carrier as far as the specific OS level you receive), refer:
http://supportforums.blackberry.com/t5/General-BlackBerry-10-Smartphone/How-to-Reload-your-Blackberr...
For the more controlled (by you, letting you decide exactly what to install) method, refer:
http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Library won't open after ML upgrade

My iPhoto library won't open. I click on the icon, and it will try to start iphoto, and will say that it unexpectedly quit a couple of times. Then it will finally pull up a balloon= asking me if i want to open the windows that were open when it crashed. Wither way, THe library won't show up, adn when I tell it to change to my iPhoto library, it does nothing. This started happenning as soon as I upgraded to Mountain Lion. I have run system update, and am running the latest version of all my software.
Please help.

I had a similar problem, after upgrading to Mountain Lion on my (2008) MBP with iPhote form iLife'09 on it, it said it couldn't open the database because changes had been made to it with a newer version of iPhoto (?). After trying lots of things, like restoring the library from Time Machine again (first time I used the migration assistant), I finally found my solution: upgrade iPhoto to 8.1 first, using
http://support.apple.com/kb/DL885
Mystically, at first my MBP didn't want to run the update, said the developer was not to be trusted (???), I had to change my security settings temporarily to make it run software 'from any source', but that did the trick. I can now use my old iPhoto from iLife'09 again. Hope it helps for you as well.

ZenV Plus STILL stuck in recovery mode after firmware upgrade

=Hi there,
My ZenV plus opened in recovery mode for no apparent reason... I have tried every option to try to fix it, including downloading and installing the firmware upgrade - this generated a message saying the upgrade was successful but the player will still only start in Recovery Mode after trying to reboot it. So what do I do next? Thanks in advance for any and all helpful suggestions.

AHi,
Can you please try resetting the ZEN V Plus to see if it helps?
To reset the player, use a pin to press the reset button.
Did this happen out of the blue?
Do you have any contents in the player? If you do, please remove them to see if the player is booting up properly.

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

Hello,
I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
Thank you in advance for a reply - especially from HP.

Hi cyskim,
Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

C160 couldn't open after firmware upgrade

Similar Messages

Maybe you are looking for