C220M3 LSI Storaged Raid Subsystem not ready yet 9271-8i

New C220M3 with 9271-8i out of box with 2.0.1b firmware
Control H doesn't boot into WebBios, instead I get EFI Shell with map:cannot find required map name.
Press ESC in 1 seconds to skip startup.nsh, any other key to continue
From the CIMC I select 2 drives to create a drive group and it fails with message;
Error: Storage Raid subsystem not ready yet
See screenshot;

Make sure the optionROM for the raid controller is enable in the bios. 
1)Reboot server
2)Press F2 when you see the option to go into bios
3)go to advance 
4)select the last option here I believe it is LOM and PCIe
5) verify that in slot 2 the optionROM is loaded

Similar Messages

  • Storage messages not ready yett

    i can not get my messages up on my mobile it just says message storage not ready yet, can i fix it thu my lapyop if i plug my mobile to it and if so how do it do it thanks

    Hi,
    I think that happens mostly in Nokia phones..You can try by connecting your phone to the computer and then installing Nokia PC Suite. From PC suite try to delete the unwanted messsages..
    That is just one of the solution..Here is a link from Nokia that will give you few more tips..
    message storage not ready yet
    Note:
    If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
    Although I am an HP employee, I am speaking for myself and not for HP.
    **Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

  • I TRIED TO ACTUALIZE MY SOFTWARE, BUT THE RESTORE SYSTEM HAS MORE THAN 36 HOURS AND IT IS NOT READY YET.... IT SEEMS STOPPED. BUT IA CANNOT RETRY, 'CAUSE IT WILL BEGIN AGAIN FRO THE START..... WHAT CAN I DO TO RESTORE CORRECTLY?

    my ipad 2, is not restoring from the last setup.... it is taking more than 36 hours and is not ready, is not finished yet....it seems like stopped... But it is not getting any progress. What I must do to restore and start up again?
    Thanks
    ALEXCG

    If the restore has stopped on the iPad then try putting it into recovery mode : http://support.apple.com/kb/ht4097

  • SolMan ChaRM - System landscape not ready yet

    Hi all,
    We are configuring ChaRM for an implementation use, therefore all the systems are not set up yet.
    Is it possible in SolMan to define logical component without "real" systems ?
    We saw that in STMS it was possible to create virtual systems, but how do we link these virtual systems to SolMan ChaRM ?
    Is it possible to define a virtual system landscape and to build and configure ChaRM scenario with this ?
    Thanks a lot for all your help,
    Regards.

    Yes, it is possible to define a development system and virtual systems (Q- and P-System).
    Via transaction SMSY you can describe the planned Q- and P-System at first as 'virtual'.
    Create transport routes with transport buffers as you would do for existing systems.
    Define the buffers as they should be named in future.
    For experimental purposes we connected our IDES-System to our development SolMan system.
    In this environment we could map such a ChaRM-configuration.
    In the meantime we practiced it in our production SolMan system, too.
    Best regards
    Horst

  • Epson scanning very slow - Universal binaries not ready yet...

    I just bought a iMac Dual Core to replace my G4 iMac 1.25Ghz. Both have 2gb of RAM. I am scanning my own art work to place on the web and to send by email.
    It turns out that scanning with my Epson scanner is not a bit faster. I just replaced the scanner in January with the latest model.
    After contacting Epson support, it turns out that no universal binary drivers are available and the current version is extremely slow...
    I just want to say that I find this extremely disappointing, there are a so many Epson scanners out there, and than this....
    And Epson can't / doesn't want to say when this will be fixed...
    Thank you for contacting the Epson Connection.
    We are currently testing new drivers for the Intel Duo Core System Macs.
    Once the testing is complete, new drivers will be posted on the applicable Epson Support web-sites. Due to the complexity of this process, we cannot promise an exact date for availability. Please check the Epson Support web-sites for any new driver postings at support.epson.com.
    iMac Dual Core Intel Mac OS X (10.4.5) 2gb memory

    I found Universal Binaries for my Epson Multifunction CX6600
    so check out frequently ...
    Thierry

  • TS440 / LSI 9240-8i RAID 5 not possible

    Hello,
    I´ve received our TS440 with the built in LSI MegaRAID card.
    I am able to see all 3 drives - but I am not able to get RAID 5 up and working.
    Is this something which has to be licensed first?
    Firmware has been updated to the latest one yesterday.
    Screenshots: http://cloudy.3f8h.net/ZFSb/3m5zI4PN
    Lenovo Support hasn´t a clue and LSI support did not respond yet.
    Thank you!

    Hello,
    The RAID 500 (LSI 9240) does require a RAID 5 upgrade key to enable RAID 5 functionality.
    You can find the upgrade key here.  Although the TS440 is not specifically called out, the key is for the RAID 500 (9240) card itself and not machine specific.

  • Firefox is trying to update my 8.0 version to 9.0.1. I'm not ready to do so because the Norton Toolbar is not yet compatable with the new Firefox release. How do I get firefox to stop trying to update every time I open the application?

    Question
    Firefox is trying to update my 8.0 version to 9.0.1. I'm not ready to do so because the Norton Toolbar is not yet compatable with the new Firefox release. How do I get firefox to stop trying to update every time I open the application?

    Swarnava wrote: '''''Firefox 9 is Compatible with Norton 2011, 2012, 360 v5'''''.
    This reads backwards, It is the other way as "Norton update is compatible with Firefox 9".

  • JNDI subsystem is not ready to use and java.lang.NoClassDefFoundError: org

    Hi,
    I am installing Access point management system on WebLogic Server 9.2 MP3.In the Admin server logs i am facing the following error:
    Sep 25, 2011 6:29:33 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:29:33 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:30:03 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:30:03 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:30:03 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:30:03 AM com.alcatel.hdm.providers.authentication.JDBCHelper initializeDS
    WARNING: Could not initialize datasource: /motive/jdbc/MotiveTxDataSource: JNDI subsystem is not ready for use
    Sep 25, 2011 6:31:20 AM net.sf.ehcache.config.ConfigurationFactory parseConfiguration
    WARNING: No configuration found. Configuring ehcache from ehcache-failsafe.xml found in the classpath: zip:/opt/hdmres_HAserver1/domains/HDMDomain/servers/necapms01-s0
    9_7204/tmp/_WL_user/nec-res-femto-1_3_0/r4j89a/APP-INF/lib/ehcache-1.6.0.jar!/ehcache-failsafe.xml
    My access point is not able to communicate with the Application.I am not sure due to above error or nor but this is the error i am getting.
    Another error is related to log4j due to which trace logs are not generating
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Error> <JMSClientExceptions> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Defa
    ult (self-tuning)'> <<anonymous>> <> <> <1316911802433> <BEA-055165> <The following exception has occurred:
    java.lang.NoClassDefFoundError: org/apache/log4j/spi/ThrowableInformation
    java.lang.NoClassDefFoundError: org/apache/log4j/spi/ThrowableInformation
    at org.apache.log4j.spi.LoggingEvent.<init>(LoggingEvent.java:145)
    at org.apache.log4j.Category.forcedLog(Category.java:379)
    at org.apache.log4j.Category.error(Category.java:310)
    at motive.serversupport.jms.SubscriberConnection.onException(SubscriberConnection.java:280)
    at weblogic.jms.client.JMSExceptionContext$1.run(JMSExceptionContext.java:54)
    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
    at weblogic.jms.client.JMSExceptionContext.invokeListener(JMSExceptionContext.java:50)
    at weblogic.jms.client.JMSSession.onException(JMSSession.java:2610)
    at weblogic.jms.client.JMSConsumer.pushException(JMSConsumer.java:736)
    at weblogic.jms.client.JMSConsumer.invoke(JMSConsumer.java:753)
    at weblogic.messaging.dispatcher.Request.wrappedFiniteStateMachine(Request.java:759)
    at weblogic.messaging.dispatcher.DispatcherImpl.dispatchAsyncInternal(DispatcherImpl.java:129)
    at weblogic.messaging.dispatcher.DispatcherImpl.dispatchNoReply(DispatcherImpl.java:160)
    at weblogic.jms.dispatcher.DispatcherAdapter.dispatchNoReply(DispatcherAdapter.java:27)
    at weblogic.jms.frontend.FESession.pushException(FESession.java:3072)
    at weblogic.jms.frontend.FEConsumer.pushException(FEConsumer.java:361)
    at weblogic.jms.frontend.FEConsumer.invoke(FEConsumer.java:824)
    at weblogic.messaging.dispatcher.Request.wrappedFiniteStateMachine(Request.java:759)
    at weblogic.messaging.dispatcher.DispatcherImpl.dispatchAsyncInternal(DispatcherImpl.java:129)
    at weblogic.messaging.dispatcher.DispatcherImpl.dispatchNoReply(DispatcherImpl.java:160)
    at weblogic.jms.dispatcher.DispatcherAdapter.dispatchNoReply(DispatcherAdapter.java:27)
    at weblogic.jms.backend.BESessionImpl.removeConsumerWithError(BESessionImpl.java:1453)
    at weblogic.jms.backend.BEConsumerImpl.closeWithError(BEConsumerImpl.java:662)
    at weblogic.jms.backend.BEDestinationImpl.closeAllConsumers(BEDestinationImpl.java:1048)
    at weblogic.jms.backend.BETopicImpl.closeAllConsumers(BETopicImpl.java:757)
    at weblogic.jms.backend.BEDestinationImpl.shutdownInternal(BEDestinationImpl.java:851)
    at weblogic.jms.backend.BEDestinationImpl.shutdown(BEDestinationImpl.java:824)
    at weblogic.jms.backend.BackEnd.removeDestination(BackEnd.java:1476)
    at weblogic.jms.backend.BEDestinationRuntimeDelegate.unprepare(BEDestinationRuntimeDelegate.java:269)
    at weblogic.jms.backend.udd.UDDEntity.unprepare(UDDEntity.java:466)
    at weblogic.jms.module.JMSModule$EntityState.setState(JMSModule.java:1695)
    at weblogic.jms.module.JMSModule$EntityState.setState(JMSModule.java:1667)
    at weblogic.jms.module.JMSModule$EntityState.access$100(JMSModule.java:1608)
    at weblogic.jms.module.JMSModule.unprepare(JMSModule.java:462)
    at weblogic.jms.module.ModuleCoordinator.unprepare(ModuleCoordinator.java:313)
    at weblogic.application.internal.flow.ModuleListenerInvoker.unprepare(ModuleListenerInvoker.java:136)
    at weblogic.application.internal.flow.DeploymentCallbackFlow$1.previous(DeploymentCallbackFlow.java:366)
    at weblogic.application.utils.StateMachineDriver.previousState(StateMachineDriver.java:52)
    at weblogic.application.utils.StateMachineDriver.previousState(StateMachineDriver.java:42)
    at weblogic.application.internal.flow.DeploymentCallbackFlow.unprepare(DeploymentCallbackFlow.java:107)
    at weblogic.application.internal.flow.DeploymentCallbackFlow.unprepare(DeploymentCallbackFlow.java:98)
    at weblogic.application.internal.BaseDeployment$1.previous(BaseDeployment.java:621)
    at weblogic.application.utils.StateMachineDriver.previousState(StateMachineDriver.java:52)
    at weblogic.application.utils.StateMachineDriver.previousState(StateMachineDriver.java:42)
    at weblogic.application.internal.BaseDeployment.unprepare(BaseDeployment.java:255)
    at weblogic.application.internal.DeploymentStateChecker.unprepare(DeploymentStateChecker.java:196)
    at weblogic.deploy.internal.targetserver.AppContainerInvoker.unprepare(AppContainerInvoker.java:118)
    at weblogic.deploy.internal.targetserver.BasicDeployment.unprepare(BasicDeployment.java:284)
    at weblogic.management.deploy.internal.DeploymentAdapter$1.doUnprepare(DeploymentAdapter.java:84)
    at weblogic.management.deploy.internal.DeploymentAdapter.unprepare(DeploymentAdapter.java:210)
    at weblogic.management.deploy.internal.AppTransition$7.transitionApp(AppTransition.java:75)
    at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:233)
    at weblogic.management.deploy.internal.ConfiguredDeployments.unprepare(ConfiguredDeployments.java:204)
    at weblogic.management.deploy.internal.ConfiguredDeployments.undeploy(ConfiguredDeployments.java:192)
    at weblogic.management.deploy.internal.DeploymentServerService.shutdownApps(DeploymentServerService.java:188)
    at weblogic.management.deploy.internal.DeploymentServerService.shutdownHelper(DeploymentServerService.java:120)
    at weblogic.application.ApplicationService.halt(ApplicationService.java:142)
    at weblogic.t3.srvr.ServerServicesManager.haltInternal(ServerServicesManager.java:417)
    at weblogic.t3.srvr.ServerServicesManager.halt(ServerServicesManager.java:264)
    at weblogic.t3.srvr.T3Srvr.shutdown(T3Srvr.java:865)
    at weblogic.t3.srvr.T3Srvr.forceShutdown(T3Srvr.java:773)
    at weblogic.t3.srvr.ServerRuntime.forceShutdown(ServerRuntime.java:330)
    at weblogic.server.RemoteLifeCycleOperationsImpl.forceShutdown(RemoteLifeCycleOperationsImpl.java:57)
    at weblogic.server.RemoteLifeCycleOperationsImpl_WLSkel.invoke(Unknown Source)
    at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:553)
    at weblogic.rmi.internal.BasicServerRef$1.run(BasicServerRef.java:443)
    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:147)
    at weblogic.rmi.internal.BasicServerRef.handleRequest(BasicServerRef.java:439)
    at weblogic.rmi.internal.BasicServerRef.access$300(BasicServerRef.java:61)
    at weblogic.rmi.internal.BasicServerRef$BasicExecuteRequest.run(BasicServerRef.java:983)
    at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
    at weblogic.work.ExecuteThread.run(ExecuteThread.java:181)
    >
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JMS> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)
    '> <hdm_admin> <> <> <1316911802443> <BEA-040324> <JMSServer "necapms01-s09_7204_jms" is suspending.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JMS> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)
    '> <hdm_admin> <> <> <1316911802456> <BEA-040325> <JMSServer "necapms01-s09_7204_jms" is suspended.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802467> <BEA-001514> <Destroying Data Source HDMJDBCPool.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802471> <BEA-001515> <Data Source HDMJDBCPool has been successfully destroyed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802471> <BEA-001508> <Destroying Connection Pool HDMJDBCPool.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802478> <BEA-001128> <Connection for pool "HDMJDBCPool" closed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802480> <BEA-001128> <Connection for pool "HDMJDBCPool" closed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Warning> <Common> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-t
    uning)'> <hdm_admin> <> <> <1316911802480> <BEA-000632> <Resource Pool "HDMJDBCPool" shutting down, ignoring 1 resources still in use by applications..>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802483> <BEA-001126> <Destroyed Connection Pool named HDMJDBCPool.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802489> <BEA-001514> <Destroying Data Source DashboardJDBCDataSource4HDMJDBCDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802489> <BEA-001515> <Data Source DashboardJDBCDataSource4HDMJDBCDataSource has been successfully destroyed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802490> <BEA-001508> <Destroying Connection Pool DashboardJDBCDataSource4HDMJDBCDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802492> <BEA-001128> <Connection for pool "DashboardJDBCDataSource4HDMJDBCDataSource" closed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802492> <BEA-001126> <Destroyed Connection Pool named DashboardJDBCDataSource4HDMJDBCDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802498> <BEA-001514> <Destroying Data Source CPEAuthDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802498> <BEA-001515> <Data Source CPEAuthDataSource has been successfully destroyed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802498> <BEA-001508> <Destroying Connection Pool CPEAuthDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802500> <BEA-001128> <Connection for pool "CPEAuthDataSource" closed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802501> <BEA-001126> <Destroyed Connection Pool named CPEAuthDataSource.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <MessagingBridge> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (
    self-tuning)'> <hdm_admin> <> <> <1316911802594> <BEA-200001> <The messaging bridge service has successfully shut down.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JMS> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)
    '> <hdm_admin> <> <> <1316911802596> <BEA-040308> <JMS service is suspending.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JMS> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)
    '> <hdm_admin> <> <> <1316911802599> <BEA-040107> <Undeployed 8 default connection factories.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JMS> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)
    '> <hdm_admin> <> <> <1316911802600> <BEA-040015> <JMS shutdown is complete.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802601> <BEA-001144> <Force Suspending the JDBC service.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802601> <BEA-001146> <Force suspend of the JDBC service completed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802601> <BEA-001147> <Shutting down the JDBC service.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <JDBC> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning
    )'> <hdm_admin> <> <> <1316911802602> <BEA-001149> <Shutdown of the JDBC service completed.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <Cluster> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tun
    ing)'> <hdm_admin> <> <> <1316911802604> <BEA-000103> <Disconnecting from cluster HDMCluster>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Notice> <Server> <necapms01-s09> <necapms01-s09_7204> <DynamicSSLListenThread[DefaultAdministration]> <<WLS Kernel>> <> <> <131
    6911802605> <BEA-002607> <Channel "DefaultAdministration" listening on 10.66.12.212:9203 was shutdown.>
    ####<Sep 25, 2011 6:20:02 AM GMT+05:30> <Info> <WebLogicServer> <necapms01-s09> <necapms01-s09_7204> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (s
    elf-tuning)'> <hdm_admin> <> <> <1316911802605> <BEA-000236> <Stopping execute threads.>
    ####<Sep 25, 2011 6:25:52 AM GMT+05:30> <Notice> <WebLogicServer> <> <> <main> <> <> <> <1316912152282> <BEA-000395> <Following extensions directory contents added to t
    he end of the classpath:
    /opt/hdmres_HAserver1/weblogic92/platform/lib/p13n/p13n-schemas.jar:/opt/hdmres_HAserver1/weblogic92/platform/lib/p13n/p13n_common.jar:/opt/hdmres_HAserver1/weblogic92/
    platform/lib/p13n/p13n_system.jar:/opt/hdmres_HAserver1/weblogic92/platform/lib/wlp/netuix_common.jar:/opt/hdmres_HAserver1/weblogic92/platform/lib/wlp/netuix_schemas.j
    ar:/opt/hdmres_HAserver1/weblogic92/platform/lib/wlp/netuix_system.jar:/opt/hdmres_HAserver1/weblogic92/platform/lib/wlp/wsrp-common.jar>
    ####<Sep 25, 2011 6:25:52 AM GMT+05:30> <Info> <WebLogicServer> <> <> <main> <> <> <> <1316912152587> <BEA-000377> <Starting WebLogic Server with Java HotSpot(TM) Serve
    r VM Version 1.5.0_15-b04 from Sun Microsystems Inc.>
    ####<Sep 25, 2011 6:27:38 AM GMT+05:30> <Notice> <Security> <> <> <main> <> <> <> <1316912258744> <BEA-090169> <Loading trusted certificates from the jks keystore file
    /opt/hdmres_HAserver1/weblogic92/server/lib/DemoTrust.jks.>
    ####<Sep 25, 2011 6:27:38 AM GMT+05:30> <Notice> <Security> <> <> <main> <> <> <> <1316912258775> <BEA-090169> <Loading trusted certificates from the jks keystore file
    /opt/hdmres_HAserver1/jdk150_15/jre/lib/security/cacerts.>
    ####<Sep 25, 2011 6:29:28 AM GMT+05:30> <Info> <Management> <> <> <main> <> <> <> <1316912368207> <BEA-141107> <Version: WebLogic Server Temporary Patch for CR370311 Tu
    e Jun 03 14:20:55 IST 2008
    Please suggest your valuable opinion to resolve these issues.
    Thanks,
    Harish Chowdhary
    >

    Hello,
    I recommend not the xmlpull jar file, but the xpp3-*.jar file found with your Enterprise installation.  It's in the "external" subfolder where you got your other Enterprise jar files.
    You'll have to remove the xmlpull jar, since they'd version conflict.
    Sincerely,
    Ted Ueda

  • No system manager locations set, search application might not be ready yet

    Hi,
    I am just setting up a new SharePoint 2013 environment (Windows server 2008 R2 + SQL Server 2008 R2) and I am getting this error message in powershell when I try to save my new search topology: No system manager locations set, search application might
    not be ready yet. The installation script used to install and create the search service originates from this link: http://www.toddklindt.com/blog/Lists/Posts/Post.aspx?ID=378 and I receive the error message after running $clone.Activate().
    ULS is writing this:
    05-29-2013 14:57:00.94 mssearch.exe (0x19C0) 0x1A68 SharePoint Server Search Crawler:Content Plugin cd11 Critical Content Plugin can not be initialized - list of CSS addresses is not set.
    05-29-2013 14:56:08.27 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration dkd5 High synchronizing search service instance 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:08.27 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration eff0 High synchronizing search data access service instance 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.38 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ajzc7 Medium Cleanup of Orphan Systems in server SR00667 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration agwve Medium Synchronizing legacy admin 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ai4f1 High Unable to get systemmanagerlocation from db 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ai84s Medium Skipping legacy admin sync as there is no system manager location set 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration agwvc Medium Skipping Topology Synchronize.The active topology does not have any Components. 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ajnco Medium Cleaning up Orphan nodes in system : 7B4831 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    So basically all else is going fine before saving the clone. Application pool is created, search service and it´s proxy is created (the databases are also created in SQL). The clone is after this created and then the components are added.
    I have tested with both March and April CU. I use separate accouns for search service, installation and so on. I have tested giving the search application pool account local admin right but didnt make any difference.
    Some posts in Internet around this matter is pointing towards there might be 4 missing patches like here: http://blog.steigis.ch/sharepoint/sps2013/search-in-starting-state/  They are all installed on my server.
    Search host controller service and SharePoint Server Search are started.
    Before creating the service I ran this. I have done this on all my other installations of search to solve the problem with the host service is in "starting" state. Info taken from here: http://mmman.itgroove.net/2012/12/search-host-controller-service-in-starting-state-sharepoint-2013-8/
    $acl = Get-Acl HKLM:\System\CurrentControlSet\Control\ComputerName
    $person = [System.Security.Principal.NTAccount] "Users"
    $access = [System.Security.AccessControl.RegistryRights]::FullControl
    $inheritance = [System.Security.AccessControl.InheritanceFlags] "ContainerInherit, ObjectInherit"
    $propagation = [System.Security.AccessControl.PropagationFlags]::None
    $type = [System.Security.AccessControl.AccessControlType]::Allow
    $rule = New-Object System.Security.AccessControl.RegistryAccessRule($person, $access, $inheritance, $propagation, $type)
    $acl.AddAccessRule($rule)
    Set-Acl HKLM:\System\CurrentControlSet\Control\ComputerName $acl
    $sh = Get-SPServiceInstance | ? {$_.TypeName -eq "Search Host Controller Service"}
    After this I do a server restart and continue with creating the search service and its components.
    Any ideas?

    I had exactly the same issue when setting up a new SharePoint 2013 environment (Windows Server 2012, SP2013 with PU March 2013 and CU April 2013, .NET 4.5). I have tried almost everything during the last weeks to configure the Search Service Applicatione,
    e.g. create the service from GUI, create it from PowerShell, verify my search account had enough permissions, check for missing updates etc. etc. Same error no matter what I tried.
    Using another SharePoint farm I went through a similar configuration of the Search Service Application. I used exactly the same script as I did on the first server and the setup completed without any issues. So why did the same features fail during the setup?
    To find an answer I compared the two farms and the only thing I noticed that were different was the lack of .NET 3.5 on the application and WFE server in the first farm. I then enabled .NET 3.5 features and now the Search Service Application works as expected
    I had no idea enabling .NET 3.5 features would solve the issue - I thought .NET 4.5 was backward compatible and SharePoint only requires .NET 4.5 according the
    requirements?

  • Is there a Windows XP compatible version of InDesign I can use as a trial? I'm not ready to buy a new computer yet.

    Is there a Windows XP compatible version of InDesign I can use as a trial? I'm not ready to buy a new computer yet, but need to practice.

    Look thru the system requirements for the various versions and then download the trial version accordingly...
    InDesign - http://helpx.adobe.com/indesign/system-requirements.html
    You can download the trial version of the software thru the site linked below.
    Be sure to follow the steps outlined in the Note: Very Important Instructions section on the download pages at this site and have cookies enabled in your browser or else the download will not work properly.
    http://prodesigntools.com/tag/ddl

  • Dumping camera HD but not ready for edit

    I'm just getting started with shooting video & FCE, storing storing files and all this jargon, so bear with me here. All of this is frighteningly overwhelming and I'm trying to get the "basics" understood.
    I want to clear out my camcorder HD and save the files on my external HD for later editing (and general backup), as I'm not ready to jump into editing yet. I've read that the media must remain in its "original file structure", as FCE doesn't work with isolated .mts files. Can I save the video media directly to my external HD or must I use Log & Transfer through FCE? What would you do?
    Also, should I connect my camera and external HD to the computer individually or connect the external HD to the computer and then the camera to the external HD?
    Thanks for helping this newb!

    Hi -
    You are correct, you need to save the entire memory structure of the camera storage media in order to successfully use Log and Transfer on video that has been archived off the camera media and on to a hard drive.
    Here is a workflow to do that, it looks harder than it is:
    Plug the camera in via USB, the media appears as a drive on the desktop -
    !http://www.spotsbeforeyoureyes.com/DMG1.jpg!
    Then, in the Finder, go to the menu Go > Utilities-
    !http://www.spotsbeforeyoureyes.com/DMG2.jpg!
    When the Utilities window opens, double click on the Disk Utility.app to launch it -
    !http://www.spotsbeforeyoureyes.com/DMG3.jpg!
    Select the camera storage on the left hand pane, then click the +new image icon -
    !http://www.spotsbeforeyoureyes.com/DMG4.jpg!
    Leave the Image format and encryption to their default settings. Navigate where you want your archival disk copy to be placed, and give it a name (like the date, etc.) and click Save -
    !http://www.spotsbeforeyoureyes.com/DMG5.jpg!
    Disk Utility will do it's thing and make the disk image of everything on you camera storage (all files, folders, data - all intact and all exactly as it appeared on the camera storage media) in this case on an external drive -
    !http://www.spotsbeforeyoureyes.com/DMG6.jpg!
    Eject the camera from your computer -
    !http://www.spotsbeforeyoureyes.com/DMG7.jpg!
    Unplug your camera and double click on the disk image archive you just created on your drive. The camera media storage will reappear, mounting to your desktop, this time originating from the archive and not the camera.
    BEFORE you reformat the camera media or erase the clips on the camera media (reformatting preferred), launch FCE and Log and Transfer, navigate to the archival disk image on your desktop and verify that all is well.
    Hope this helps.
    MtD

  • To RAID or not to RAID, that is the question

    People often ask: Should I raid my disks?
    The question is simple, unfortunately the answer is not. So here I'm going to give you another guide to help you decide when a raid array is advantageous and how to go about it. Notice that this guide also applies to SSD's, with the expection of the parts about mechanical failure.
     What is a RAID?
     RAID is the acronym for "Redundant Array of Inexpensive Disks". The concept originated at the University of Berkely in 1987 and was intended to create large storage capacity with smaller disks without the need for very expensive and reliable disks, that were very expensive at that time, often a tenfold of smaller disks. Today prices of hard disks have fallen so much that it often is more attractive to buy a single 1 TB disk than two 500 GB disks. That is the reason that today RAID is often described as "Redundant Array of Independent Disks".
    The idea behind RAID is to have a number of disks co-operate in such a way that it looks like one big disk. Note that 'Spanning' is not in any way comparable to RAID, it is just a way, like inverse partitioning, to extend the base partition to use multiple disks, without changing the method of reading and writing to that extended partition.
     Why use a RAID?
     Now with these lower disks prices today, why would a video editor consider a raid array? There are two reasons:
    1. Redundancy (or security)
    2. Performance
    Notice that it can be a combination of both reasons, it is not an 'either/or' reason.
     Does a video editor need RAID?
    No, if the above two reasons, redundancy and performance are not relevant. Yes if either or both reasons are relevant.
    Re 1. Redundancy
    Every mechanical disk will eventually fail, sometimes on the first day of use, sometimes only after several years of usage. When that happens, all data on that disk are lost and the only solution is to get a new disk and recreate the data from a backup (if you have one) or through tedious and time-consuming work. If that does not bother you and you can spare the time to recreate the data that were lost, then redundancy is not an issue for you. Keep in mind that disk failures often occur at inconvenient moments, on a weekend when the shops are closed and you can't get a replacement disk, or when you have a tight deadline.
    Re 2. Performance
    Opponents of RAID will often say that any modern disk is fast enough for video editing and they are right, but only to a certain extent. As fill rates of disks go up, performance goes down, sometimes by 50%. As the number of disk activities on the disk go up , like accessing (reading or writing) pagefile, media cache, previews, media, project file, output file, performance goes down the drain. The more tracks you have in your project, the more strain is put on your disk. 10 tracks require 10 times the bandwidth of a single track. The more applications you have open, the more your pagefile is used. This is especially apparent on systems with limited memory.
    The following chart shows how fill rates on a single disk will impact performance:
    Remember that I said previously the idea behind RAID is to have a number of disks co-operate in such a way that it looks like one big disk. That means a RAID will not fill up as fast as a single disk and not experience the same performance degradation.
    RAID basics
     Now that we have established the reasons why people may consider RAID, let's have a look at some of the basics.
    Single or Multiple? 
    There are three methods to configure a RAID array: mirroring, striping and parity check. These are called levels and levels are subdivided in single or multiple levels, depending on the method used. A single level RAID0 is striping only and a multiple level RAID15 is a combination of mirroring (1) and parity check (5). Multiple levels are designated by combining two single levels, like a multiple RAID10, which is a combination of single level RAID0 with a single level RAID1.
    Hardware or Software? 
    The difference is quite simple: hardware RAID controllers have their own processor and usually their own cache. Software RAID controllers use the CPU and the RAM on the motherboard. Hardware controllers are faster but also more expensive. For RAID levels without parity check like Raid0, Raid1 and Raid10 software controllers are quite good with a fast PC.
    The common Promise and Highpoint cards are all software controllers that (mis)use the CPU and RAM memory. Real hardware RAID controllers all use their own IOP (I/O Processor) and cache (ever wondered why these hardware controllers are expensive?).
    There are two kinds of software RAID's. One is controlled by the BIOS/drivers (like Promise/Highpoint) and the other is solely OS dependent. The first kind can be booted from, the second one can only be accessed after the OS has started. In performance terms they do not differ significantly.
    For the technically inclined: Cluster size, Block size and Chunk size
     In short: Cluster size applies to the partition and Block or Stripe size applies to the array.
    With a cluster size of 4 KB, data are distributed across the partition in 4 KB parts. Suppose you have a 10 KB file, three full clusters will be occupied: 4 KB - 4 KB - 2 KB. The remaining 2 KB is called slackspace and can not be used by other files. With a block size (stripe) of 64 KB, data are distributed across the array disks in 64 KB parts. Suppose you have a 200 KB file, the first part of 64 KB is located on disk A, the second 64 KB is located on disk B, the third 64 KB is located on disk C and the remaining 8 KB on disk D. Here there is no slackspace, because the block size is subdivided into clusters. When working with audio/video material a large block size is faster than smaller block size. Working with smaller files a smaller block size is preferred.
    Sometimes you have an option to set 'Chunk size', depending on the controller. It is the minimal size of a data request from the controller to a disk in the array and only useful when striping is used. Suppose you have a block size of 16 KB and you want to read a 1 MB file. The controller needs to read 64 times a block of 16 KB. With a chunk size of 32 KB the first two blocks will be read from the first disk, the next two blocks from the next disk, and so on. If the chunk size is 128 KB. the first 8 blocks will be read from the first disk, the next 8 block from the second disk, etcetera. Smaller chunks are advisable with smaller filer, larger chunks are better for larger (audio/video) files.
    RAID Levels
     For a full explanation of various RAID levels, look here: http://www.acnc.com/04_01_00/html
    What are the benefits of each RAID level for video editing and what are the risks and benefits of each level to help you achieve better redundancy and/or better performance? I will try to summarize them below.
    RAID0
     The Band AID of RAID. There is no redundancy! There is a risk of losing all data that is a multiplier of the number of disks in the array. A 2 disk array carries twice the risk over a single disk, a X disk array carries X times the risk of losing it all.
    A RAID0 is perfectly OK for data that you will not worry about if you lose them. Like pagefile, media cache, previews or rendered files. It may be a hassle if you have media files on it, because it requires recapturing, but not the end-of-the-world. It will be disastrous for project files.
    Performance wise a RAID0 is almost X times as fast as a single disk, X being the number of disks in the array.
    RAID1
     The RAID level for the paranoid. It gives no performance gain whatsoever. It gives you redundancy, at the cost of a disk. If you are meticulous about backups and make them all the time, RAID1 may be a better solution, because you can never forget to make a backup, you can restore instantly. Remember backups require a disk as well. This RAID1 level can only be advised for the C drive IMO if you do not have any trust in the reliability of modern-day disks. It is of no use for video editing.
    RAID3
    The RAID level for video editors. There is redundancy! There is only a small performance hit when rebuilding an array after a disk failure due to the dedicated parity disk. There is quite a perfomance gain achieveable, but the drawback is that it requires a hardware controller from Areca. You could do worse, but apart from it being the Rolls-Royce amongst the hardware controllers, it is expensive like the car.
    Performance wise it will achieve around 85% (X-1) on reads and 60% (X-1) on writes over a single disk with X being the number of disks in the array. So with a 6 disk array in RAID3, you get around 0.85x (6-1) = 425% the performance of a single disk on reads and 300% on writes.
    RAID5 & RAID6
     The RAID level for non-video applications with distributed parity. This makes for a somewhat severe hit in performance in case of a disk failure. The double parity in RAID6 makes it ideal for NAS applications.
    The performance gain is slightly lower than with a RAID3. RAID6 requires a dedicated hardware controller, RAID5 can be run on a software controller but the CPU overhead negates to a large extent the performance gain.
    RAID10
     The RAID level for paranoids in a hurry. It delivers the same redundancy as RAID 1, but since it is a multilevel RAID, combined with a RAID0, delivers twice the performance of a single disk at four times the cost, apart from the controller. The main advantage is that you can have two disk failures at the same time without losing data, but what are the chances of that happening?
    RAID30, 50 & 60
     Just striped arrays of RAID 3, 5 or 6 which doubles the speed while keeping redundancy at the same level.
    EXTRAS
     RAID level 0 is striping, RAID level 1 is mirroring and RAID levels 3, 5 & 6 are parity check methods. For parity check methods, dedicated controllers offer the possibility of defining a hot-spare disk. A hot-spare disk is an extra disk that does not belong to the array, but is instantly available to take over from a failed disk in the array. Suppose you have a 6 disk RAID3 array with a single hot-spare disk and assume one disk fails. What happens? The data on the failed disk can be reconstructed in the background, while you keep working with negligeable impact on performance, to the hot-spare. In mere minutes your system is back at the performance level you were before the disk failure. Sometime later you take out the failed drive, replace it for a new drive and define that as the new hot-spare.
    As stated earlier, dedicated hardware controllers use their own IOP and their own cache instead of using the memory on the mobo. The larger the cache on the controller, the better the performance, but the main benefits of cache memory are when handling random R+W activities. For sequential activities, like with video editing it does not pay to use more than 2 GB of cache maximum.
    REDUNDANCY(or security)
    Not using RAID entails the risk of a drive failing and losing all data. The same applies to using RAID0 (or better said AID0), only multiplied by the number of disks in the array.
    RAID1 or 10 overcomes that risk by offering a mirror, an instant backup in case of failure at high cost.
    RAID3, 5 or 6 offers protection for disk failure by reconstructing the lost data in the background (1 disk for RAID3 & 5, 2 disks for RAID6) while continuing your work. This is even enhanced by the use of hot-spares (a double assurance).
    PERFORMANCE
     RAID0 offers the best performance increase over a single disk, followed by RAID3, then RAID5 amd finally RAID6. RAID1 does not offer any performance increase.
    Hardware RAID controllers offer the best performance and the best options (like adjustable block/stripe size and hot-spares), but they are costly.
     SUMMARY
     If you only have 3 or 4 disks in total, forget about RAID. Set them up as individual disks, or the better alternative, get more disks for better redundancy and better performance. What does it cost today to buy an extra disk when compared to the downtime you have when a single disk fails?
    If you have room for at least 4 or more disks, apart from the OS disk, consider a RAID3 if you have an Areca controller, otherwise consider a RAID5.
    If you have even more disks, consider a multilevel array by striping a parity check array to form a RAID30, 50 or 60.
    If you can afford the investment get an Areca controller with battery backup module (BBM) and 2 GB of cache. Avoid as much as possible the use of software raids, especially under Windows if you can.
    RAID, if properly configured will give you added redundancy (or security) to protect you from disk failure while you can continue working and will give you increased performance.
    Look carefully at this chart to see what a properly configured RAID can do to performance and compare it to the earlier single disk chart to see the performance difference, while taking into consideration that you can have one disks (in each array) fail at the same time without data loss:
    Hope this helps in deciding whether RAID is worthwhile for you.
    WARNING: If you have a power outage without a UPS, all bets are off.
    A power outage can destroy the contents of all your disks if you don't have a proper UPS. A BBM may not be sufficient to help in that case.

    Harm,
    thanks for your comment.
    Your understanding  was absolutely right.
    Sorry my mistake its QNAP 639 PRO, populated with 5 1TB, one is empty.
    So for my understanding, in my configuration you suggest NOT to use RAID-0. Im not willing to have more drives in my workstation becouse if my projekts are finished, i archiv on QNAP or archiv on other external drive.
    My only intention is to have as much speed and as much performance as possible during developing a projekt 
    BTW QNAP i also use as media-center in combination with Sony PS3 to run the encoded files.
    For my final understanding:
    C:  i understand
    D: i understand
    E and F: does it mean, when i create a projekt on E, all my captured and project-used MPEG - files should be situated in F?  Or which media in F you mean?
    Following your suggestions in want to rebulid Harms-Best Vista64-Benchmark comp to reach maximum speed and performance. Can i use in general the those hardware components (exept so many HD drives and exept Areca raid controller ) in my drive configuration C to F. Or would you suggest some changings in my situation?

  • Can you check my final setup? Two things not clear yet

    Hey guys,
    Just when I thought I got it all figured out, something new (at least to me) pops up and raises more questions than answers. So I go on and search more and more and more and now finally I think i've got my setup allmost ready to order. Could you check it and help me out on the final insecurities? Thanx a bunch.
    Oh and please, if you have a suggestions to change something I feel is allready o.k (so no questions)...make it a suggestion with enough info to let me make a choice in the matter. Give me a link to a Benchmarksite or e really good test. If the difference is minimal (seconds) on about 10 min. of final footage, than please don't send me on a chase again. My girlfriend would like me to bed with her at the same time now after a week or so
    and    I want to order the damn.. stuff and start.
    Camera:               Canon XF 100, uses Canon  MPEG-2 4:2:2 50Mbps codec            
    Software:             Adobe Premiere Pro CS5.53
    Motherboard:       ASUS P8Z68-V Pro
    Question: not to much benchmarks around on the Z68 combined with I 2700. Anyone who uses this board with the 2700 or 2700K step forward please and elaborate.
    Cpu:                     intel      core I7 2600
    Memory:               16 Gb    Kingston ValueRAM (2x 8 GB : 2 x 4 GB - DIMM 240-pins - DDR3 - 1333 MHz
    or
    Cpu:                     intel      core I7 2600K
    Memory:               16 Gb    Corsair Vengeance Blue 16GB DDR3-1600 CL9 quad kit
    Question:               I think I’d go for the first option. It’s cheaper and from what I’ve read there not a lot to gain. My videos mostly don’t exceed 10                               minutes of final footage. Anyone can acknowledge this (or not)?
    Videocard:           MSI        N570GTX-M2D12D5/OC
    Harddisk:             OCZ       Vertex 3 120GB   (sata 600) for my OS
    Harddisk:             S’sung  WD Caviar Green WD20EARS x3 (sata 300)
    To raid or not to raid is still not clear for me. 5 is definitely a no go
    I’m thinking I’d put 2 disks in a Raid 0 for more speed and on a regular base BAckup to the other one( and eventually go for external back-up)
    Is that ‘o.k. or mmh’, then fine. Is it a ‘oh no, what is he thinking’, please tell me.
    Cooler:                Scythe  Mugen                 2 Rev. B
    Housing:              Cooler Master  Xilencio
    Powersupply:       Seasonic 620
    Monitor:               Eizo       EV2333WH-BK
    Optische drive:     LG          BH10LS30
    Cardreader:          lexar     LEXAR PROFESSIONAL USB 3.0 DUAL-SLOT READER (for CF’s canoncamera)
    Speakers              Creative              GigaWorks T20 Series II
    Special :               Contour Design ShuttlePro2
    Thanx guys and girls(?) for hopefully making my life easier. Greeting from Nieuwegein, Utrecht, Holland

    Scott,
    Referring to your post #8.
    JCschild wrote:
    i have proven this to be false....
    This is a big concern to some of us end users who want to put our money where it counts.
    Is there a clear benchmark varifying your actual test results, which us newbies can view?
    Referring to your post #10 above.
    they are also end users not system builders and do not have the resources/access we have to multiple platforms, processors ram etc.
    How can we really know for sure if we go on word of mouth only, one swears by Ford, one swears by Chevy.
    What should us newbies believe,
    the feedback from end users who have the real world experience of the behaviour of their systems working regularly with large or complex projects, with strict timelines under time pressure, who cannot afford jerkiness nor delay of any kind, who must afford to save a lot of aggravation caused by less responsive systems, who cannot afford to be held back by hard disk failure or loss of data that took valuable time editing, who need lesser time requirements for regular backups, etc, who know what video editing involves in real practice,
    or the feedback from system builders who have “the resources/access to multiple platforms, processors ram etc.” to run hardware tests, but who do not have the experience of high end video editing in practice?
    Perhaps it is true that a video card running at PCIe-8x is not much slower than a video card running at PCIe-16x.
    I don't know for sure.
    What will happen if things change, sooner than we thought, with new drivers and CS6 PP utilizing the full bandwidth, and end users are stuck with systems that don't have the required PCI-e lanes to accomodate more than a 16 x PCI-e nVidia card?
    It appears to me that the i7-2600K is indeed a great processor, delivering great value for money, for the majority of general-purpose applications, but
    how does it perform when one works with large or complex projects, and multitask, such as having DW do a complete validation on multiple DHTML files, including SSE, running a resize action in PS on a couple of thousand images, encoding large files in FL and PR doing an export to a complex long form BRD?
    I was very tempted, and came very close, to buying an i7-2600K for myself, but after learning just how much high-end video editing can demand from a system, I became hesitant to buy the i7-2600K with its platform. I need to be sure that the system I buy has no limitations for the work I need to do with it.
    If Intel had video editing in mind when designing the i7-2600K, it would not have had integrated graphics, which is of no use when we need a nVidia card.
    Regardless of the fact that according to http://www.xbitlabs.com/articles/cpu/display/core-i7-2600k-990x.html the i7-2600K outperformed many pricier products for a higher-end LGA1366 platform (even the $1000 i7-990X Extreme Edition yielding significantly to Core i7-2600K within the majority of general-purpose applications, except during video processing and transcoding, final rendering and a few specific tasks, such as encryption and batch image processing), Intel still positioned this processor as a mid-level processor, for a reason.
    Intel knew before release what this mid-level i7-2600K was capable of, therefore releasing it positioned as a mid-level processor, they did so having the architecture to follow up with a mid-level processor that will outperform the i7-2600K, within the same price category, else who would buy Intel's next mid-level processors?
    I suspect that for those who are willing to hold out and wait just a bit longer, so they can put their money where it counts, Intel has a pleasant surprise coming soon, and that the new platform will not be evolutionary like it has been for years, but revolutionary with feature improvements from Sandy Bridge like Intel's tri-gate transistor technology, PCI Express 3.0 support and Graphics DirectX 11 and OpenCL support, a bigger graphics performance and bigger CPU performance boost compared to Sandy Bridge.
    what makes you think you need a raid controller.... the vast majority of Adobe users do not need one or an 8 drive raid array..
    Yes, for those who never need a hardware raid controller, using it for general-purpose applications, the 2600K and its P67 or Z68 platform is nice.
    The OP did not specify whether or not he will need a hardware controller, wherefore I cared to post my post #7 above,
    nor did he specify his source material, editing style, the nature of his timelines and the time pressure he is under with his projects (other than a mention in his original post of his girlfriend's time request), or how long he intends to use the system before upgrading to the next one.
    and why i finally posted the big cup of zip it thread.. to clear out some mis-leading comments. 
    Scott
    ADK
    Quoting from your original post in A big cup of "zip it" or the definative final P67 vs X58 answer thread :
    Now in all fairless of disclosure the drive benchmarks dropped from our previous tests on X58 which is odd, we are guessing the video card as its ramping up would take bandwidth from the controller even though its supposed to be running 8x.
    Scott
    ADK
    Since you wrote that “the direct replacement for X58 is X79” (System build for CS5.5. Contemplating whether or not to wait for Q1/Q2 2012.), I am eager to learn which exact motherboard(s) was/were used when you ran those previous tests on X58?
    Supposing the video card took bandwidth from the controller, even though its supposed to be running 8x, why do you think it would do that as it's ramping up?
    Is there a clear benchmark varifying your actual test results, which us newbies can view?

  • "This drive is not ready for use; it's door may be open ..."

    Hi.
    I recently updated to itunes 7, and then had an issue with a corrupt file on the i-pod (which resulted in chkdsk hanging itself at 27%, always). So I restored the i-pod and that took care of that - chkdsk now says it's fine.
    However - it is also empty. My machine and i-tunes recognize it fine upon start-up; however, a short while into a full synch to get my library back on the i-pod, I invariably get the following error message:
    "The drive is not ready for use; it's door may be open. Please check drive \Device\Harddisk\DR 3 and make sure that a disk is inserted and that the drive door is closed." The message comes with the options "cancel, ignore and continue", yet the latter two don't make a difference, and even if I choose cancel, itunes keeps trying until it eventually crashes.
    This always happens after itunes has synchronized about 1.13 GB (out of 18.55 available).
    As far as I can tell, both my system and the iPod are up to date (itunes and windows update say so, anyway). E: is unequivocally and exclusively allocated to the i-pod; changing the settings from "optimize for quick removal" to "optimize for performance" has made no discernible difference.
    Any ideas would be very much appreciated.
    Thanks.
    DELL Inspiron 4150   Windows XP  

    Hullo ...
    let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
    That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
    It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
    Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
    Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
    Thanks.

  • Firefox beta 35 not ready for prime time.

    I have spent the entire weekend trying to get the Firefox beta 35 to work. What I have found is that *all* extensions fail to work with the exception of Places Maintenance. I can not download any extension Firefox is so famous for. The error is something like "cannot install 'plugin-name' in it's current state." Enabling any extension require a FF restart, even Places Maintenance. Trying to remove an extension fails and must be done manually.
    I am on Windows 7 Premium desktop Firefox, 32 bit. I "committed" myself to FF 35 last night (which meant clearing history and cache on exit because the extension "Expire History by Days" was no longer working), when I discovered that 35 was not playing nice with some sites using Flash. It was a capricious thing. Many sites worked as normal but some would not render at all. Examples:
    http://www.wunderground.com/US/WI/La_Crosse.html
    http://www.weather.com/weather/5day/l/Hustler+WI+54637:4:US
    First time I have has a problem with a Firefox beta, but it is definitely not ready for prime time. I realize FF is attempting to get away from what we are calling "Proprietary add-ons" but FF 35 in its present state will just fill the Moz Support forums with millions of complaints (guess I am one of the first). I have at present 1 extension (the only one that works on 35), the above mentioned "Places Maintenance."
    I thought you might like this report as "user input." God knows I have tried...I must have downloaded 35 at least a dozen times and then been forced back to 34.0.5. So I am back on 34.0.5
    I have submitted a bug report here:
    https://bugzilla.mozilla.org/show_bug.cgi?id=1108196
    Let me know if anyone else is having these problems or anyone needs more information. I'd love to help fix this. I know some of you good support people have probably tried 35. Are you having the same difficulties?
    Below is my (34.0.5 but the same as I had on 35 last night with the exception of "Version") trouble shooting information minus a million entries for my printer:
    Application Basics
    Name: Firefox
    Version: 34.0.5
    User Agent: Mozilla/5.0 (Windows NT 6.1; rv:34.0) Gecko/20100101 Firefox/34.0
    Multiprocess Windows: 0/1
    Crash Reports for the Last 3 Days
    All Crash Reports
    Extensions
    Name: Places Maintenance
    Version: 1.3
    Enabled: false
    ID: [email protected]
    Graphics
    Adapter Description: NVIDIA GeForce 9400 GT
    Adapter Drivers: nvd3dum nvwgf2um,nvwgf2um
    Adapter RAM: 1024
    ClearType Parameters: Gamma: 2200 Pixel Structure: B ClearType Level: 50 Enhanced Contrast: 300
    Device ID: 0x0641
    Direct2D Enabled: true
    DirectWrite Enabled: true (6.2.9200.16571)
    Driver Date: 12-19-2013
    Driver Version: 9.18.13.3221
    GPU #2 Active: false
    GPU Accelerated Windows: 1/1 Direct3D 11 (OMTC)
    Subsys ID: 304619da
    Vendor ID: 0x10de
    WebGL Renderer: Google Inc. -- ANGLE (NVIDIA GeForce 9400 GT Direct3D9Ex vs_3_0 ps_3_0)
    windowLayerManagerRemote: true
    AzureCanvasBackend: direct2d
    AzureContentBackend: direct2d
    AzureFallbackCanvasBackend: cairo
    AzureSkiaAccelerated: 0
    Important Modified Preferences
    accessibility.typeaheadfind.flashBar: 0
    browser.cache.disk.capacity: 358400
    browser.cache.disk.smart_size_cached_value: 358400
    browser.cache.disk.smart_size.first_run: false
    browser.cache.disk.smart_size.use_old_max: false
    browser.cache.frecency_experiment: 3
    browser.places.smartBookmarksVersion: 7
    browser.search.suggest.enabled: false
    browser.search.useDBForOrder: true
    browser.sessionstore.enabled: false
    browser.sessionstore.max_tabs_undo: 0
    browser.sessionstore.upgradeBackup.latestBuildID: 20141126041045
    browser.startup.homepage: http://www.wcwcw.com/
    browser.startup.homepage_override.buildID: 20141126041045
    browser.startup.homepage_override.mstone: 34.0.5
    browser.tabs.loadInBackground: false
    browser.urlbar.autocomplete.enabled: false
    dom.indexedDB.enabled: false
    dom.mozApps.used: true
    dom.w3c_touch_events.expose: false
    extensions.lastAppVersion: 34.0.5
    font.internaluseonly.changed: false
    general.autoScroll: false
    gfx.direct3d.last_used_feature_level_idx: 1
    keyword.URL: https://www.google.com/search?q=
    media.gmp-gmpopenh264.lastUpdate: 1413301734
    media.gmp-gmpopenh264.version: 1.1
    media.gmp-manager.lastCheck: 1417991594
    network.cookie.cookieBehavior: 2
    network.cookie.prefsMigrated: true
    places.database.lastMaintenance: 1418059778
    places.history.expiration.transient_current_max_pages: 80511
    plugin.disable_full_page_plugin_for_types: application/vnd.fdf,application/vnd.adobe.xdp+xml,application/vnd.adobe.xfdf,application/pdf
    plugin.importedState: true
    plugin.state.np32dsw: 1
    plugin.state.npdeployjava: 0
    plugin.state.npgoogleupdate: 0
    plugin.state.nppdf: 2
    plugin.state.npwatweb: 2
    privacy.clearOnShutdown.cookies: false
    privacy.clearOnShutdown.formdata: false
    privacy.clearOnShutdown.offlineApps: true
    privacy.clearOnShutdown.sessions: false
    privacy.cpd.cache: false
    privacy.cpd.cookies: false
    privacy.cpd.offlineApps: true
    privacy.cpd.sessions: false
    privacy.popups.showBrowserMessage: false
    privacy.sanitize.migrateFx3Prefs: true
    privacy.sanitize.sanitizeOnShutdown: true
    privacy.sanitize.timeSpan: 0
    security.disable_button.openCertManager: false
    security.disable_button.openDeviceManager: false
    security.warn_viewing_mixed: false
    storage.vacuum.last.index: 1
    storage.vacuum.last.places.sqlite: 1415513129
    Important Locked Preferences
    JavaScript
    Incremental GC: true
    Accessibility
    Activated: false
    Prevent Accessibility: 0
    Library Versions
    NSPR
    Expected minimum version: 4.10.7
    Version in use: 4.10.7
    NSS
    Expected minimum version: 3.17.2 Basic ECC
    Version in use: 3.17.2 Basic ECC
    NSSSMIME
    Expected minimum version: 3.17.2 Basic ECC
    Version in use: 3.17.2 Basic ECC
    NSSSSL
    Expected minimum version: 3.17.2 Basic ECC
    Version in use: 3.17.2 Basic ECC
    NSSUTIL
    Expected minimum version: 3.17.2
    Version in use: 3.17.2
    Experimental Features
    ---------------------

    Just for the record I'm using Fx35b1 with lots of plug-ins and extensions with absolutely no problems now or for quite a long time.

Maybe you are looking for

  • Some of the error idocs are not falling into Workflow Inbox

    The extract of IDOC list with status 51 from WE02 transaction is not matching with Workflow inbox column "object", some of the idocs which are errored are not showing in the workflow inbox. Here we are in need to get all the errored idocs into the in

  • Estimated delivery dates for iPad 4 with wifi and cellular UK

    I have ordered the new iPad 32gb With wifi and cellular data and on my account it just says late November. Is there any way to find out a more specific date as I am going away and want to take it with me?? Would I have to ring Apple and ask?

  • Flag purchase requisition as closed automatically

    Hi, I'd like to flag a purchase requisition as closed automatically when it is created with reference of a purchase requisition. I'd like to know if there's any customizing point in which I can customize this action. Thanks in advance, Gerard

  • Can the USB-9211 Thermocouple Input device measure voltages ?

    Can the USB-9211 be used to measure voltages ? It is designed for thermocouple measurements and its operating manual states there is a current source between its TC+ and TC- input terminals. What amount of current is flowing ? Does it depend on the s

  • Install Flex 2 on Eclipse

    I have Eclipse 3.3.1.1 and Flex SDK 2.0.1 How do I import the SDK into Eclipse? Instructions are vague.