C2960-S SFP Module not active
I have set up Cisco switches previously via the hyperterminal and been able to get them configured and operating, but I have limited knowledge of the tools and processes.
I have a 2960-S with 48 ports and 4 SFP modules.
I have good feedback on the 48 ports, but I can not get the SFP modules to ether be recognized or show any activity on the 2960-S. The unmanaged switch I have the fiber connected too, is indicating a network connection and activity, but the 2960-S is not indicating any connection on the SFP modules.
I have added the switch configuration file.
Ok. I see you posted your config above, and after reading a bit more here, you're dealing with layers 1-2 of the OSI model at the moment, so let's focus on that. For your unmanaged switch, are you using the same type of SFP? Sometimes you need to use the same on both sides for a link to come up. I have tried off branded + Cisco before and it had lots of problems. Also
If that is not the problem, I would say look over your running-configuration for port 49. It does not appear to have any configuration added to it so far. If every device on your unmanaged switch will be on the same vlan, you can turn port 49 into 'switchport mode access' and 'switchport access vlan 1' as well as 'spanning-tree portfast'.
If not all devices will be on vlan 1 on your unmanaged device, you can try 'switchport mode trunk'. This will allow vlans 1-4094 across by default (you can limit this too). Make sure that the unmanaged switch is set to trunk mode as well, and allowing the vlans you want across.
For troubleshooting, you can try 'show spanning-tree vlan <xxx>' where xxx is the vlan you are having trouble with. Lastly, you can also try to issue a 'show interface gig 1/0/49 counters detail', which will show you all the types of packets entering the port. This varies from ios version to ios version, but it will show unicast, multicast, broadcast, packets below the MTU or above (runts and giants).
I hope that helps : )
Similar Messages
-
SFP module not showing up as interface choice
I am trying to configure a 3825 router w/IOS 12.4(3d).
When I install a GLC-SX-MM module, I cannot see the module in the sh diag results and therefore not a choice in the list of interfaces.
When I view the logs, the insertion is logged.
Any assistance would be greatly appreciated,
ChrisHi Chris,
There are two Gigabit Ethernet ports on Cisco 3800 Series systems. Port 1 is a fixed 10/100/1000BASE-T RJ-45. Port 0 can choose between 10/100/1000BASE-T RJ-45 and an SFP module slot. SFP modules are optional.
A new command-line interface (CLI) allows you to choose between the two media types. The "SFP" option will only come up if there is a SFP module plugged into the slot. RJ-45 is the default.
Please see the following configurations to get this port working:
Cisco3825#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Cisco3825(config)#interface gigabitEthernet 0/0
Cisco3825(config-if)#media-type ?
rj45 Use RJ45 connector
sfp Use SFP connector
Cisco3825(config-if)#media-type sfp
After this you should be able to use and see the SFP on the router. Hope this helps. :)
Regards,
Param -
in SFP transaction;
when i press layout buton , it give me an error.
SOFFICEINTEGRATION020
'Direct display for documents not activated'Yes i installed .
One of our product systems , i take this error but another one it works correctly . -
I have downloaded adobe lightroom 5 students . Developpement module is not active. Is it normal?
I have downloaded adobe lightroom 5 students . Developpement module is not active. Is it normal?
Do you have a License key? 24 digit numerical? If yes uninstall to existing version of Lightroom using your operating system procedure, this will not interfere with your catalog, preferences and personal files.
Download the appropriate version for your operating system from this site. Product updates proceed to install and enter your License key.
If you have a Adobe Creative Cloud subscription then you may need to uninstall the existing version the reboot and open the Adobe Creative Cloud Application Manager, login to your account and Lightroom CC should be available to install. The application will be automatically activated. -
Compatibility with SFP modules
Hi,
I have a query, I need connect a Switch 6500 with a switch HP, the switch HP has a HP X242 10 SFP module and need connect to the switch 6500 with a module CVR-X2-SFP10G. I need to know if this modules are compatible.
Thanks for the help.According to the 6500 module installation manual, and a Q&A document,
"Q. What is the difference between WS-X6716-10G-3C and WS-X6716-10G-3CXL?
A. Both modules offer 16 ports of 10 Gigabit Ethernet and share the same base board, WS-X6716-10GE. WS-X6716-10G-3C comes with distributed forwarding card 3C (WS-F6700-DFC3C), and WS-X6716-10G-3CXL comes with distributed forwarding card 3CXL (WS-F6700-DFC3CXL)."
"A sticker is placed on the module faceplate identifying it as either a WS-X6816-10G-2T or WS-X6816-10G-2TXL depending on whether a WS-F6K-DFC4-E or WS-F6K-DFC4-EXL daughter card is installed on the module."
"Not all 10-GB transceiver versions may be supported on your module. Refer to your software release notes to determine if a specific 10-GB transceiver is supported on your module."
It seems you will need to determine which daughter card or forwarding card is installed in the base WS-C6716-10GE board; then refer to the software release notes for transceiver compatibility. The longer reach SFP+ copper or active optical interfaces draw more power, thus they may not be supported with the X2 to SFP+ converter. -
DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
Hi
ABAP instant of ECC6 System is started but Java instant isnt started please find below of dev_w0
And i found error in dev_w0 is DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active and in dev_disp is DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
Error ==> ThPlgSend00B: MpiwriteOutOfBand <d> failed (14)
Error ==> DLoadLib: Loadlibrary (D:\usr\sap\xxx\DVEBMGS00\exe\dbsdbslib.dll)
Error 126 = "the specified module could not be found"
Error => Couldn't load library 'D:\usr\sap\XXX\DVEBMGS00\exe\dbsdbslib.dll'
Please find below dev_w0 and dev_disp
A Fri Apr 25 16:56:30 2008
A
A -PXA--
A PXA INITIALIZATION
A System page size: 4kb, total admin_size: 10332kb, dir_size: 10260kb.
A Attached to PXA (address 5F620040, size 300000K)
A abap/pxa = shared protect gen_remote
A PXA INITIALIZATION FINISHED
A -PXA--
A
A
A Fri Apr 25 16:56:31 2008
A ABAP ShmAdm attached (addr=43A0C000 leng=20955136 end=44E08000)
A >> Shm MMADM area (addr=43E81EF8 leng=126176 end=43EA0BD8)
A >> Shm MMDAT area (addr=43EA1000 leng=16150528 end=44E08000)
A RFC Destination> destination ordvmsapecc_V37_00 host ordvmsapecc system V37 systnr 0 (ordvmsapecc_V37_00)
A RFC Options> H=ordvmsapecc,S=00,d=2,
A RFC FRFC> fallback activ but this is not a central instance.
A
A RFC rfc/signon_error_log = -1A RFC rfc/dump_connection_info = 0
A RFC rfc/dump_client_info = 0
A RFC rfc/cp_convert/ignore_error = 1
A RFC rfc/cp_convert/conversion_char = 23
A RFC rfc/wan_compress/threshold = 251
A RFC rfc/recorder_pcs not set, use defaule value: 2
A RFC rfc/delta_trc_level not set, use default value: 0
A RFC rfc/no_uuid_check not set, use default value: 0
A RFC rfc/bc_ignore_thcmaccp_retcode not set, use default value: 0
A RFC Method> initialize RemObjDriver for ABAP Objects
M ThrCreateShObjects allocated 19000 bytes at 0A410040
N SsfSapSecin: putenv(SECUDIR=D:\usr\sap\V37\DVEBMGS00\sec): ok
N
N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is D:\usr\sap\V37\DVEBMGS00\exe\sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N
N Fri Apr 25 16:56:32 2008
N ===...sucessfully completed.
N =================================================
N MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
N MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
M JrfcVmcRegisterNativesDriver o.k.
W =================================================
W === ipl_Init() called
B dbtran INFO (init_connection '<DEFAULT>' [MSSQL:700.08]):
B max_blocking_factor = 50, max_in_blocking_factor = 255,
B min_blocking_factor = 5, min_in_blocking_factor = 10,
B prefer_union_all = 1, prefer_join = 1,
B prefer_fix_blocking = 0, prefer_in_itab_opt = 0,
B convert AVG = 1, alias table FUPD = 0,
B escape_as_literal = 0, opt GE LE to BETWEEN = 0,
B select * =0x00, character encoding = STD / []:X,
B use_hints = abap->1, dbif->0x1, upto->0, rule_in->0,
B rule_fae->0, concat_fae->0, concat_fae_or->0
W ITS Plugin: Path dw_gui
W ITS Plugin: Description ITS Plugin - ITS rendering DLL
W ITS Plugin: sizeof(SAP_UC) 2
W ITS Plugin: Release: 700, [7000.0.95.20050900]
W ITS Plugin: Int.version, [33]
W ITS Plugin: Feature set: [12]
W ===... Calling itsp_Init in external dll ===>
W === ipl_Init() returns 0, ITSPE_OK: OK
W =================================================
E Enqueue Info: rdisp/wp_no_enq=1, rdisp/enqname=<empty>, assume ordvmsapecc_V37_00
E Replication is disabled
E EnqCcInitialize: local lock table initialization o.k.
E EnqId_SuppressIpc: local EnqId initialization o.k.
E EnqCcInitialize: local enqueue client init o.k.
M
M Fri Apr 25 16:56:33 2008
M MBUF info for hooks: MS component UP
M ThSetEnqName: set enqname by server list
M ThISetEnqname: enq name = >ordvmsapecc_V37_00 <
E
E *************** EnqId_EN_ActionAtMsUpHook ***************
E Hook on upcoming Ms (with EnqSrv), get auth EnqId and check it locally
E
E *************** ObjShMem_CheckAuthoritativeEnqId ***************
E Checking authoritative EnqId from EnqSrv into ObjShMem
E ObjShMem_CheckAuthoritativeEnqId: ObjShMem ...
E EnqId.EnqTabCreaTime = -999
E EnqId.RandomNumber = -999
E ReqOrd.TimeInSecs = -999
E ReqOrd.ReqNumberThisSec = -999
E ObjShMem_CheckAuthoritativeEnqId: ObjShMem ...
E EnqId.EnqTabCreaTime = -999
E EnqId.RandomNumber = -999
E ReqOrd.TimeInSecs = -999
E ReqOrd.ReqNumberThisSec = -999
E ObjShMem_CheckAuthoritativeEnqId: EnqId is initial in ShMem
E ObjShMem_CheckAuthoritativeEnqId: Overwrite incoming auth EnqId, continue
E EnqId inscribed into initial ObjShMem: (ObjShMem_CheckAuthoritativeEnqId)
E -SHMEM--
E EnqId: EnqTabCreaTime/RandomNumber = 25.04.2008 16:56:32 1209135392 / 3024
E ReqOrd at Srv: TimeInSecs/ReqNumberThisSec = 25.04.2008 16:56:33 1209135393 / 1
E ReqOrd at Cli: TimeInSecs/ReqNumberThisSec = 25.04.2008 16:56:33 1209135393 / 1
E Status: STATUS_OK
E -
M ThActivateServer: state = STARTING
L BtcSysStartRaise: Begin
L Raise event SAP_SYSTEM_START with parameter <ordvmsapecc_V37_00 >
L BtcSysStartRaise: End
S
S Fri Apr 25 16:56:34 2008
S server @>SSRV:ordvmsapecc_V37_00@< appears or changes (state 1)
S server @>SSRV:ordvmsapecc_V37_00@< appears or changes (state 1)
C
C Fri Apr 25 17:02:53 2008
C The IRow interface is supported by this OLEDB provider
B table logging switched off for all clients
S
S Fri Apr 25 17:03:56 2008
S found spool memory service RSPO-ACTIONS at 27719C38
Please find the dev_disp file
trc file: "dev_disp", trc level: 1, release: "700"
sysno 00
sid V37
systemid 560 (PC with Windows NT)
relno 7000
patchlevel 0
patchno 95
intno 20050900
make: multithreaded, Unicode, optimized
pid 4832
Fri Apr 25 16:55:20 2008
kernel runs with dp version 224000(ext=109000) (@(#) DPLIB-INT-VERSION-224000-UC)
length of sys_adm_ext is 572 bytes
SWITCH TRC-HIDE on ***
Fri Apr 25 16:55:21 2008
***LOG Q00=> DpSapEnvInit, DPStart (00 4832) [dpxxdisp.c 1239]
shared lib "dw_xml.dll" version 95 successfully loaded
shared lib "dw_xtc.dll" version 95 successfully loaded
shared lib "dw_stl.dll" version 95 successfully loaded
shared lib "dw_gui.dll" version 95 successfully loaded
shared lib "dw_mdm.dll" version 95 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Fri Apr 25 16:55:25 2008
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 4 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5355]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >ordvmsapecc_V37_00 <
DpShMCreate: sizeof(wp_adm) 25776 (1432)
DpShMCreate: sizeof(tm_adm) 4232256 (21056)
DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm) 528064 (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (72)
DpShMCreate: sizeof(vmc_adm) 0 (1520)
DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 071C0040, size: 4898888)
DpShMCreate: allocated sys_adm at 071C0040
DpShMCreate: allocated wp_adm at 071C1E80
DpShMCreate: allocated tm_adm_list at 071C8330
DpShMCreate: allocated tm_adm at 071C8360
DpShMCreate: allocated wp_ca_adm at 075D17A0
DpShMCreate: allocated appc_ca_adm at 075D7560
DpShMCreate: allocated comm_adm at 075D94A0
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 0765A360
DpShMCreate: allocated gw_adm at 0765A3A0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 0765A3D0
DpShMCreate: allocated wall_adm at 0765A3D8
MBUF state OFF
DpCommInitTable: init table for 500 entries
Fri Apr 25 16:55:28 2008
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation view
<EsNT> Memory Reset disabled as NT default
<ES> 1999 blocks reserved for free list.
ES initialized.
J2EE server info
start = TRUE
state = STARTED
pid = 5168
argv[0] = D:\usr\sap\V37\DVEBMGS00\exe\jcontrol.EXE
argv[1] = D:\usr\sap\V37\DVEBMGS00\exe\jcontrol.EXE
argv[2] = pf=D:\usr\sap\V37\SYS\profile\V37_DVEBMGS00_ordvmsapecc
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=1789
argv[5] = -DSAPSYSTEM=00
argv[6] = -DSAPSYSTEMNAME=V37
argv[7] = -DSAPMYNAME=ordvmsapecc_V37_00
argv[8] = -DSAPPROFILE=D:\usr\sap\V37\SYS\profile\V37_DVEBMGS00_ordvmsapecc
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
Please guide me to solve the issue..
Thanks
Jayson.
Edited by: Peter jayson on Apr 28, 2008 9:52 AM
Edited by: Peter jayson on Apr 28, 2008 9:55 AM
Edited by: Peter jayson on Apr 28, 2008 10:02 AMHi Juan,
i checked in SM52 But in VMC is not loaded
Shared GC is inactive
Global Classes is 0 bytes
Global programs is 0 Bytes
Global Data is 0 Bytes
Other Global Data is 0 Bytes
Error Occured 0
Please guid me how to load the VMC and make the active the Shared GC
Thanks
Jayson -
Cisco prime 4.2 monitor SFP conn & isdn active call session
Hello all,
my customer already bought cisco prime 4.2 , they asked me if this cisco prime is able to monitor the SFP (fiber connector) status active/not active and monitor the voice call active session for 24 hours ? anyone can help me to configure it ?
thanks in advance,i couldn't find the appropriate MIB to monitor the call session
-
Archive and print and archive buttons not active
I create a smartform and join it in sap. It is transection me9a.
The problem when I run the program comes printpreview. There are two button that "Archive" and "Print and Archive". But they are not active. I wan to use them. What sould I do?Pass the below parameter to smartform function module,
Ex,
EXPORTING
control_parameters = control_param
output_options = output_opt
Check the below structure:
data: control_param type ssfctrlop,
output_opt type ssfcompop.
control_param-no_dialog = 'X'.
control_param-preview = 'X'.
control_param-getotf = ''.
output_opt-tddest = 'LOCL'.
output_opt-tdnoprint = 'X'.
Similarly chack the other structure <b>ssfctrlop</b>
Just a rough idea given above.
Close the thread if your question is answered.
Regards,
SaiRam -
Dear All,
In Adapter Monitoring, i am not able to see the JDBC adapter in the Onlly Installed and Started Adapters, but i am able to see the JDBC Adapter in the All Adapters.
When i tried to restart the JDBC adapter service in the Visual Administration, there it not giving option for either stopping or starting the JDBC adapter.
DefaultTrace log is as shown below.
#1.5 #0018FE28105C00710000101400002D7A0004554CA8859398#1219687640044#com.sap.aii.af.service.administration.impl.AlertingStatusListener##com.sap.aii.af.service.administration.impl.AlertingStatusListener.run()#J2EE_GUEST#0##n/a##4065565072d011dd95800018fe28105c#XI AF AAM AlertingStatusListener$AsyncAlerter@483756c4_185020##0#0#Error##Java###Unable to raise alert for fatal process status (adapter :, channel ): com.sap.aii.af.service.alerting.AlertingException: JCoClient connection missingHost:srpidev_SPD_00|AdapterType:File|Sender::BS_File_Sender|Receiver::|Interface:mi_vendor:http://file2idoc|MsgID:null#3#http://sap.com/xi/XI/System#File#39b1b7a3830a32978c0ebde7d7b6a672#
#1.5 #0018FE28105C005900000F8200002D7A0004554CA8D15AE3#1219687645010#com.sap.aii.adapter.file.File2XI##com.sap.aii.adapter.file.File2XI.invoke()#J2EE_GUEST#0##n/a##32b5c44072d011ddcbc00018fe28105c#XI File2XI[CC_File_Sender_to_ABAP/BS_File_Sender/]_185029##0#0#Error#1#/Applications/ExchangeInfrastructure/AdapterFramework/Services/ADAPTER/ADMIN/File#Plain###Channel CC_File_Sender_to_ABAP: No suitable sender agreement found#
#1.5 #0018FE28105C005800000F4900002D7A0004554CA8D16217#1219687645012#com.sap.aii.af.service.alerting.Connection##com.sap.aii.af.service.alerting.Connection.newJcoClientForCentralMonitoringServer()#J2EE_GUEST#0##n/a##8cafa8c072cc11ddbc6f0018fe28105c#XI AF AAM AlertingStatusListener$AsyncAlerter@3f72187f_185030##0#0#Error##Plain###Connect to SAP gateway failed
Connect_PM TYPE=A ASHOST=srpidev.srhouse.com SYSNR=00 GWHOST=srpidev.srhouse.com GWSERV=sapgw00 PCS=1
LOCATION CPIC (TCP/IP) on local host with Unicode
ERROR hostname 'srpidev.srhouse.com' unknown
TIME Mon Aug 25 23:37:25 2008
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -2
MODULE nixxhsl.cpp
LINE 223
DETAIL NiHsLGetNodeAddr: hostname cached as unknown
COUNTER 959
#1.5 #0018FE28105C005800000F4A00002D7A0004554CA8D16B2D#1219687645014#com.sap.aii.af.service.administration.impl.AlertingStatusListener##com.sap.aii.af.service.administration.impl.AlertingStatusListener.run()#J2EE_GUEST#0##n/a##8cafa8c072cc11ddbc6f0018fe28105c#XI AF AAM AlertingStatusListener$AsyncAlerter@3f72187f_185030##0#0#Error##Java###Unable to raise alert for fatal process status (adapter :, channel ): com.sap.aii.af.service.alerting.AlertingException: JCoClient connection missingHost:srpidev_SPD_00|AdapterType:File|Sender::BS_File_Sender|Receiver:null:null|Interface:null:null|MsgID:null#3#http://sap.com/xi/XI/System#File#e07325c431493887a7288ca7bb4c0318#
#1.5 #0018FE28105C005400000F1500002D7A0004554CA8E111AE#1219687646040#com.sap.aii.adapter.file.File2XI##com.sap.aii.adapter.file.File2XI.invoke()#J2EE_GUEST#0##n/a##39dafd8072d011dda2450018fe28105c#XI File2XI[comc_sender/BS_File_Sender/]_185023##0#0#Error#1#/Applications/ExchangeInfrastructure/AdapterFramework/Services/ADAPTER/ADMIN/File#Plain###Channel comc_sender: Error connecting to ftp server '150.0.150.76': com.sap.aii.adapter.file.ftp.FTPEx: 530 Login incorrect.#
#1.5 #0018FE28105C005000000FC800002D7A0004554CA8E11AB4#1219687646042#com.sap.aii.af.service.alerting.Connection##com.sap.aii.af.service.alerting.Connection.newJcoClientForCentralMonitoringServer()#J2EE_GUEST#0##n/a##347b1af072d011dd88d10018fe28105c#XI AF AAM AlertingStatusListener$AsyncAlerter@6784897_185031##0#0#Error##Plain###Connect to SAP gateway failed
Connect_PM TYPE=A ASHOST=srpidev.srhouse.com SYSNR=00 GWHOST=srpidev.srhouse.com GWSERV=sapgw00 PCS=1
LOCATION CPIC (TCP/IP) on local host with Unicode
ERROR hostname 'srpidev.srhouse.com' unknown
TIME Mon Aug 25 23:37:26 2008
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -2
MODULE nixxhsl.cpp
LINE 223
DETAIL NiHsLGetNodeAddr: hostname cached as unknown
COUNTER 991
#1.5 #0018FE28105C005000000FC900002D7A0004554CA8E1239A#1219687646044#com.sap.aii.af.service.administration.impl.AlertingStatusListener##com.sap.aii.af.service.administration.impl.AlertingStatusListener.run()#J2EE_GUEST#0##n/a##347b1af072d011dd88d10018fe28105c#XI AF AAM AlertingStatusListener$AsyncAlerter@6784897_185031##0#0#Error##Java###Unable to raise alert for fatal process status (adapter :, channel ): com.sap.aii.af.service.alerting.AlertingException: JCoClient connection missingHost:srpidev_SPD_00|AdapterType:File|Sender::BS_File_Sender|Receiver::|Interface:mi_vendor:http://file2idoc|MsgID:null#3#http://sap.com/xi/XI/System#File#39b1b7a3830a32978c0ebde7d7b6a672#
Please help me to resolve this issue.
Regards,
RanjithHi
According to your Error Message,
Saying that JDBC Configuration is not Active.
Once again cross check all the config is Activated & also Test your Config Using Config Test Tool in ID
And also check in RWB-Adapter Engine-Adapter monitoring ---select the option instaled & Started. whether the JDBC Adapter is working fine or not -
Hi Experts,
Please check this Developer Trace of Dispatcher, this is stopped, when I am restarting my server, it is giving errors :
running but not connected to message server,
and
running but dialog queue standstill, J2EE service unavilable.
trc file: "dev_disp", trc level: 1, release: "700"
sysno 01
sid XID
systemid 560 (PC with Windows NT)
relno 7000
patchlevel 0
patchno 52
intno 20050900
make: multithreaded, Unicode, optimized
pid 1412
Fri Sep 21 10:19:59 2007
kernel runs with dp version 210000(ext=109000) (@(#) DPLIB-INT-VERSION-210000-UC)
length of sys_adm_ext is 572 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (01 1412) [dpxxdisp.c 1231]
shared lib "dw_xml.dll" version 52 successfully loaded
shared lib "dw_xtc.dll" version 52 successfully loaded
shared lib "dw_stl.dll" version 52 successfully loaded
shared lib "dw_gui.dll" version 52 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3901
Fri Sep 21 10:20:04 2007
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 5 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5233]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >inggnh002sap_XID_01 <
DpShMCreate: sizeof(wp_adm) 12672 (1408)
DpShMCreate: sizeof(tm_adm) 3954072 (19672)
DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm) 528064 (1048)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (72)
DpShMCreate: sizeof(vmc_adm) 0 (1452)
DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 06510040, size: 4607512)
DpShMCreate: allocated sys_adm at 06510040
DpShMCreate: allocated wp_adm at 06511E28
DpShMCreate: allocated tm_adm_list at 06514FA8
DpShMCreate: allocated tm_adm at 06514FD8
DpShMCreate: allocated wp_ca_adm at 068DA570
DpShMCreate: allocated appc_ca_adm at 068E0330
DpShMCreate: allocated comm_adm at 068E2270
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 06963130
DpShMCreate: allocated gw_adm at 06963170
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 069631A0
DpShMCreate: allocated wall_adm at 069631A8
MBUF state OFF
EmInit: MmSetImplementation( 2 ).
MM diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation flat
<EsNT> Memory Reset disabled as NT default
<ES> 511 blocks reserved for free list.
ES initialized.
J2EE server info
start = TRUE
state = STARTED
pid = 1324
argv[0] = D:\usr\sap\XID\DVEBMGS01\exe\jcontrol.EXE
argv[1] = D:\usr\sap\XID\DVEBMGS01\exe\jcontrol.EXE
argv[2] = pf=D:\usr\sap\XID\SYS\profile\XID_DVEBMGS01_inggnh002sap
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=2009
argv[5] = -DSAPSYSTEM=01
argv[6] = -DSAPSYSTEMNAME=XID
argv[7] = -DSAPMYNAME=inggnh002sap_XID_01
argv[8] = -DSAPPROFILE=D:\usr\sap\XID\SYS\profile\XID_DVEBMGS01_inggnh002sap
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1617]
Fri Sep 21 10:20:05 2007
***LOG Q0K=> DpMsAttach, mscon ( inggnh002sap) [dpxxdisp.c 11414]
DpStartStopMsg: send start message (myname is >inggnh002sap_XID_01 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
Fri Sep 21 10:20:06 2007
CCMS: start to initalize 3.X shared alert area (first segment).
DpJ2eeLogin: j2ee state = CONNECTED
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 52
Release check o.K.
Fri Sep 21 10:20:41 2007
***LOG Q0I=> NiIRead: recv (10054: WSAECONNRESET: Connection reset by peer) [nixxi.cpp 4235]
ERROR => NiIRead: SiRecv failed for hdl 4 / sock 1492
(SI_ECONN_BROKEN; I4; ST; 127.0.0.1:2014) [nixxi.cpp 4235]
DpJ2eeMsgProcess: j2ee state = CONNECTED (NIECONN_BROKEN)
DpIJ2eeShutdown: send SIGINT to SAP J2EE startup framework (pid=1324)
ERROR => DpProcKill: kill failed [dpntdisp.c 371]
DpIJ2eeShutdown: j2ee state = SHUTDOWN
Fri Sep 21 10:20:45 2007
ERROR => W0 (pid 2804) died [dpxxdisp.c 14021]
ERROR => W1 (pid 1484) died [dpxxdisp.c 14021]
ERROR => W2 (pid 2708) died [dpxxdisp.c 14021]
ERROR => W3 (pid 1464) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xbf --> 0xbe
ERROR => W4 (pid 860) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xbe --> 0xbc
ERROR => W5 (pid 2964) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xbc --> 0xb8
ERROR => W6 (pid 2508) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xb8 --> 0xb0
ERROR => W7 (pid 3840) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xb0 --> 0xa0
ERROR => W8 (pid 1072) died [dpxxdisp.c 14021]
my types changed after wp death/restart 0xa0 --> 0x80
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:20:55 2007
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long) Fri Sep 21 04:50:55 2007
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 2804 Ended no 1 0 0
1 DIA 1484 Ended no 1 0 0
2 DIA 2708 Ended no 1 0 0
3 DIA 1464 Ended no 1 0 0
4 UPD 860 Ended no 1 0 0
5 ENQ 2964 Ended no 1 0 0
6 BTC 2508 Ended no 1 0 0
7 SPO 3840 Ended no 1 0 0
8 UP2 1072 Ended no 1 0 0
Dispatcher Queue Statistics Fri Sep 21 04:50:55 2007
===========================
--------++++--
+
Typ
now
high
max
writes
reads
--------++++--
+
NOWP
0
2
2000
6
6
--------++++--
+
DIA
5
5
2000
5
0
--------++++--
+
UPD
0
0
2000
0
0
--------++++--
+
ENQ
0
0
2000
0
0
--------++++--
+
BTC
0
0
2000
0
0
--------++++--
+
SPO
0
0
2000
0
0
--------++++--
+
UP2
0
0
2000
0
0
--------++++--
+
max_rq_id 12
wake_evt_udp_now 0
wake events total 8, udp 7 ( 87%), shm 1 ( 12%)
since last update total 8, udp 7 ( 87%), shm 1 ( 12%)
Dump of tm_adm structure: Fri Sep 21 04:50:55 2007
=========================
Term uid man user term lastop mod wp ta a/i (modes)
Workprocess Comm. Area Blocks Fri Sep 21 04:50:55 2007
=============================
Slots: 300, Used: 1, Max: 0
--------++--
+
id
owner
pid
eyecatcher
--------++--
+
0
DISPATCHER
-1
WPCAAD000
NiWait: sleep (5000ms) ...
NiISelect: timeout 5000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:00 2007
NiISelect: TIMEOUT occured (5000ms)
DpHalt: shutdown server >inggnh002sap_XID_01 < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_PREPARED
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes
Stop gateway
killing process (776) (SOFT_KILL)
Stop icman
killing process (2780) (SOFT_KILL)
Terminate gui connections
wait for end of work processes
wait for end of gateway
[DpProcDied] Process lives (PID:776 HANDLE:1572)
waiting for termination of gateway ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:01 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:776 HANDLE:1572)
wait for end of icman
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:02 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:03 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:04 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:05 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:06 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:07 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:08 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:09 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:10 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:11 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process lives (PID:2780 HANDLE:1576)
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=1601
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Sep 21 10:21:12 2007
NiISelect: TIMEOUT occured (1000ms)
[DpProcDied] Process died (PID:2780 HANDLE:1576)
[DpProcDied] Process died (PID:1324 HANDLE:1556)
DpStartStopMsg: send stop message (myname is >inggnh002sap_XID_01 <)
NiIMyHostName: hostname = 'inggnh002sap'
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 189 bytes
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=562,pac=1,MESG_IO)
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 3 recv would block (errno=EAGAIN)
NiIRead: read for hdl 3 timed out (0ms)
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=114,pac=1,MESG_IO)
MsINiWrite: sent 114 bytes
send msg (len 110+4) to name MSG_SERVER, type 0, key -
MsSndName: MS_NOOP ok
Send 4 bytes to MSG_SERVER
NiIRead: hdl 3 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
Received 4 bytes from MSG_SERVER
Received opcode MS_NOOP from msg_server, reply MSOP_OK
MsOpReceive: ok
MsSendKeepalive : keepalive sent to message server
NiIRead: hdl 3 recv would block (errno=EAGAIN)
Fri Sep 21 10:21:13 2007
NiIPeek: peek for hdl 3 timed out (r; 1000ms)
NiIRead: read for hdl 3 timed out (1000ms)
DpHalt: no more messages from the message server
DpHalt: sync with message server o.k.
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c 11698]
NiBufSend starting
NiIWrite: hdl 3 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiBufISelUpdate: new MODE -- (r-) for hdl 3 in set0
SiSelNSet: set events of sock 1516 to: ---
NiBufISelRemove: remove hdl 3 from set0
SiSelNRemove: removed sock 1516 (pos=3)
SiSelNRemove: removed sock 1516
NiSelIRemove: removed hdl 3
MBUF state OFF
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 40 (AD_MSBUF), ser 0, ex 0, errno 0
blks_in_queue/wp_ca_blk_no/wp_max_no = 1/300/9
LOCK WP ca_blk 1
make DISP owner of wp_ca_blk 1
DpRqPutIntoQueue: put request into queue (reqtype 1, prio LOW, rq_id 15)
MBUF component DOWN
NiICloseHandle: shutdown and close hdl 3 / sock 1516
NiBufIClose: clear extension for hdl 3
MsIDetach: detach MS-system
cleanup EM
EsCleanup ....
EmCleanup() -> 0
Es2Cleanup: Cleanup ES2
***LOG Q05=> DpHalt, DPStop ( 1412) [dpxxdisp.c 10087]
Good Bye .....
Please Help, it is urgent,
Regards,
Study SAPHi Kaushal,
Thanks for your reply, there are many files with dev*.
Please check the log from file dev_w0 :
trc file: "dev_w0", trc level: 1, release: "700"
ACTIVE TRACE LEVEL 1
ACTIVE TRACE COMPONENTS all, MJ
B
B Fri Sep 21 10:37:39 2007
B create_con (con_name=R/3)
B Loading DB library 'D:\usr\sap\XID\DVEBMGS01\exe\dboraslib.dll' ...
B Library 'D:\usr\sap\XID\DVEBMGS01\exe\dboraslib.dll' loaded
B Version of 'D:\usr\sap\XID\DVEBMGS01\exe\dboraslib.dll' is "700.08", patchlevel (0.46)
B New connection 0 created
M sysno 01
M sid XID
M systemid 560 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 52
M intno 20050900
M make: multithreaded, Unicode, optimized
M pid 3588
M
M kernel runs with dp version 210000(ext=109000) (@(#) DPLIB-INT-VERSION-210000-UC)
M length of sys_adm_ext is 572 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 3588) [dpxxdisp.c 1293]
I MtxInit: 30000 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
M
M Fri Sep 21 10:37:40 2007
M DpShMCreate: sizeof(wp_adm) 12672 (1408)
M DpShMCreate: sizeof(tm_adm) 3954072 (19672)
M DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
M DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
M DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
M DpShMCreate: sizeof(comm_adm) 528064 (1048)
M DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
M DpShMCreate: sizeof(file_adm) 0 (72)
M DpShMCreate: sizeof(vmc_adm) 0 (1452)
M DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
M DpShMCreate: sizeof(gw_adm) 48
M DpShMCreate: SHM_DP_ADM_KEY (addr: 06510040, size: 4607512)
M DpShMCreate: allocated sys_adm at 06510040
M DpShMCreate: allocated wp_adm at 06511E28
M DpShMCreate: allocated tm_adm_list at 06514FA8
M DpShMCreate: allocated tm_adm at 06514FD8
M DpShMCreate: allocated wp_ca_adm at 068DA570
M DpShMCreate: allocated appc_ca_adm at 068E0330
M DpShMCreate: allocated comm_adm at 068E2270
M DpShMCreate: system runs without file table
M DpShMCreate: allocated vmc_adm_list at 06963130
M DpShMCreate: allocated gw_adm at 06963170
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 069631A0
M DpShMCreate: allocated wall_adm at 069631A8
X EmInit: MmSetImplementation( 2 ).
X MM diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation flat
M <EsNT> Memory Reset disabled as NT default
X ES initialized.
M ThInit: running on host inggnh002sap
M
M Fri Sep 21 10:37:41 2007
M calling db_connect ...
C Prepending D:\usr\sap\XID\DVEBMGS01\exe to Path.
C
C Fri Sep 21 10:37:47 2007
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPSR3's password
C Connecting as /@XDI on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 06AAFCF8 06AB5294 06AB4B1C
C Attaching to DB Server XDI (con_hdl=0,svchp=06AB4A68,svrhp=06AC6334)
C
C Fri Sep 21 10:37:48 2007
C Starting user session (con_hdl=0,svchp=06AB4A68,srvhp=06AC6334,usrhp=06ADB0D8)
C *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1033
[dboci.c 4345]
C Detaching from DB Server (con_hdl=0,svchp=06AB4A68,srvhp=06AC6334)
C *** ERROR => CONNECT failed with sql error '1033'
[dbsloci.c 10704]
C Try to connect with default password
C Connecting as SAPSR3/<pwd>@XDI on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 06AAFCF8 06AB5294 06AB4B1C
C Attaching to DB Server XDI (con_hdl=0,svchp=06AB4A68,svrhp=06AC6334)
C
C Fri Sep 21 10:37:49 2007
C Starting user session (con_hdl=0,svchp=06AB4A68,srvhp=06AC6334,usrhp=06ADB0D8)
C *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1033
[dboci.c 4345]
C Detaching from DB Server (con_hdl=0,svchp=06AB4A68,srvhp=06AC6334)
C *** ERROR => CONNECT failed with sql error '1033'
[dbsloci.c 10704]
B ***LOG BV3=> severe db error 1033 ; work process is stopped [dbsh#2 @ 1199] [dbsh 1199 ]
B ***LOG BY2=> sql error 1033 performing CON [dblink#3 @ 431] [dblink 0431 ]
B ***LOG BY0=> ORA-01033: ORACLE initialization or shutdown in progress [dblink#3 @ 431] [dblink 0431 ]
M ***LOG R19=> ThInit, db_connect ( DB-Connect 000256) [thxxhead.c 1403]
M in_ThErrHandle: 1
M *** ERROR => ThInit: db_connect (step 1, th_errno 13, action 3, level 1) [thxxhead.c 10019]
M
M Info for wp 0
M
M stat = 4
M reqtype = 1
M act_reqtype = -1
M rq_info = 0
M tid = -1
M mode = 255
M len = -1
M rq_id = 65535
M rq_source = 255
M last_tid = 0
M last_mode = 0
M semaphore = 0
M act_cs_count = 0
M control_flag = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M vm = V-1
M
M *****************************************************************************
M *
M * LOCATION SAP-Server inggnh002sap_XID_01 on host inggnh002sap (wp 0)
M * ERROR ThInit: db_connect
M *
M * TIME Fri Sep 21 10:37:49 2007
M * RELEASE 700
M * COMPONENT Taskhandler
M * VERSION 1
M * RC 13
M * MODULE thxxhead.c
M * LINE 10204
M * COUNTER 1
M *
M *****************************************************************************
M
M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c 720]
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c 260]
M Entering ThSetStatError
M ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
M Entering ThReadDetachMode
M call ThrShutDown (1)...
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 3588) [dpnttool.c 327]
Regards,
Study SAP -
Hi Experts,
In my program, im sending mails using SO_DOCUMENT_SEND_API1 function module.
The mail content contains a URL whose value is generated using C_DESK_DOC_GET_URL.
The URL links are getting generated and the mails were also sent successfully to the identified persons.
The issue is, the links are not active in the mails when it is viewed from MS Outlook 2007. The links are just appearing as texts not as hyperlinks in the recipients mail.
Verified for the following basic outlook settings and everything is fine.
"Tools-> Options-> Mail Format-> Editor Options-> Proofing-> tab AutoFormat
Here make sure the following options are selected;
In section Replace:
Internet and network paths with hyperlinks
In section Always AutoFormat:
Plain text mail documents"
The links are not truncated and infact it appears as hyperlink when viewed from lotus notes domino.
What could be the reason ?
Regards,
Keerthivasan.MClosing this thread.
-
Error Function module " " not found in Smartforms
Hi all,
Please help me out .
I created the form using the smartforms, check it and activated it. I can see the unique function module is assigned to the form. I wrote the ABAP program and use function module SSF_FUNCTION_MODULE_NAMEand also define data types.
when I called the function module fm_name for passing values and tables from program to smartform. This is working perfectly in development server but in production it giving error like Function module " " not found.
Below I m pasting my code.
*& Report ZCASHJOURNAL *
REPORT zcashjournal .
TABLES: bseg.
DATA: FM_NAME TYPE rs38l_fnam.
DATA:BEGIN OF it_bseg OCCURS 0.
INCLUDE STRUCTURE bseg.
DATA:END OF it_bseg.
DATA:BEGIN OF it_bseg1 OCCURS 0.
INCLUDE STRUCTURE bseg.
DATA:END OF it_bseg1.
DATA: gv_amt_in_words TYPE spell,
gv_word TYPE spell-word,
gv_decword TYPE spell-decword.
DATA:BEGIN OF gt_bkpf OCCURS 0.
INCLUDE STRUCTURE bkpf.
DATA:END OF gt_bkpf.
DATA:bktxt TYPE bktxt.
DATA:waers TYPE waers.
DATA:belnr TYPE belnr_d.
DATA:werks TYPE bukrs.
DATA:desc TYPE butxt.
DATA:awkey TYPE awkey.
DATA:docno TYPE matnr.
DATA:cajo TYPE awkey.
DATA:desc1 TYPE butxt.
DATA:dmbtr TYPE dmbtr.
SELECTION-SCREEN BEGIN OF BLOCK b2.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT (15) FOR FIELD s_belnr.
SELECTION-SCREEN POSITION 28 .
PARAMETERS : s_belnr TYPE bseg-belnr .
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT (15) FOR FIELD s_werks.
SELECTION-SCREEN POSITION 28 .
PARAMETERS: s_werks TYPE werks.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN END OF BLOCK b2.
SELECT * FROM bkpf
INTO CORRESPONDING FIELDS OF TABLE gt_bkpf
WHERE belnr LIKE s_belnr
AND bukrs LIKE s_werks.
IF NOT gt_bkpf[] IS INITIAL.
SELECT * FROM bseg
INTO CORRESPONDING FIELDS OF TABLE it_bseg
FOR ALL ENTRIES IN gt_bkpf
WHERE bukrs EQ gt_bkpf-bukrs
AND belnr EQ gt_bkpf-belnr
AND shkzg EQ 'S'.
ENDIF.
LOOP AT gt_bkpf.
bktxt = gt_bkpf-bktxt.
waers = gt_bkpf-waers.
belnr = gt_bkpf-belnr.
werks = gt_bkpf-bukrs.
awkey = gt_bkpf-awkey.
docno = awkey+0(10).
cajo = awkey+10(4).
ENDLOOP.
LOOP AT it_bseg.
dmbtr = it_bseg-dmbtr.
ENDLOOP.
IF s_werks EQ '65'.
desc = 'JCBML - Heavy Equipments'.
ENDIF.
IF cajo EQ '0001'.
desc1 = 'PETTY CASH PLANT II'.
ENDIF.
CALL FUNCTION 'SPELL_AMOUNT'
EXPORTING
amount = dmbtr
currency = waers
filler = space
language = sy-langu
IMPORTING
in_words = gv_amt_in_words
EXCEPTIONS
not_found = 1
too_large = 2
OTHERS = 3.
IF sy-subrc EQ 0.
MOVE : gv_amt_in_words-word TO gv_word,
gv_amt_in_words-decword TO gv_decword.
ENDIF.
CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
EXPORTING
formname = 'ZCASHRECPT'
IMPORTING
FM_NAME = FM_NAME
EXCEPTIONS
NO_FORM = 1
NO_FUNCTION_MODULE = 2
OTHERS = 3
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
*CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
EXPORTING formname = 'ZCASHRECPT'
variant = ' '
direct_call = ' '
IMPORTING fm_name = lf_fm_name
EXCEPTIONS no_form = 1
no_function_module = 2.
*v_vbeln = S_VBELN-low.
CALL FUNCTION FM_NAME
EXPORTING
bktxt = bktxt
waers = waers
belnr = belnr
werks = werks
desc = desc
docno = docno
cajo = cajo
desc1 = desc1
dmbtr = dmbtr
gv_word = gv_word
TABLES
T_ZDEB = it_bseg
EXCEPTIONS
formatting_error = 1
internal_error = 2
send_error = 3
user_canceled = 4
OTHERS = 5.
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.Hi Rakesh,
Check two things
1. Program tranpsorted to production without any error in request log.
2. Smartform tranpsorted to production without any error in request log and without renaming / misspelling it.
CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
EXPORTING
formname = 'ZCASHRECPT'
IMPORTING
FM_NAME = FM_NAME
EXCEPTIONS
NO_FORM = 1
NO_FUNCTION_MODULE = 2
OTHERS = 3
IF sy-subrc <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
* WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Also try to uncomment the Message id part and it will show some meaningful message.
And to check whether actaually fucntion module is generated or not goto smartforms ->Smartform name -> Display -> Environment->Fucntion module name . if this is blank try to retransport smartform.
Hope that helps.
Regards
Kapadia
***Assigning points is the way to say thanks in SDN.*** -
Hi All,
In SMICM, ICM Status is showing as Running. When we test the ICMAN service in SICF is gives an error "ICMAN NOT ACTIVE".
Instance Profile Parameters ( RZ10) for icm are as follows :
rdisp/start_icman true
icm/max_conn 700
icm/HTTP/j2ee_0 PREFIX=/,HOST=localhost,CONN=0-500,PORT=50000
icm/max_threads 100
icm/plugin_0 PROT=HTTP,PLG=D:\usr\sap\cc5\SYS\exe\run\httpplugin.dll
icm/min_threads 50
icm/server_port_2 PROT=SMTP, PORT=1025
icm/server_port_1 PROT=HTTPS, PORT=1443
icm/server_port_0 PROT=HTTP,PORT=1080
Following are the errors showing in trace file dev_icm :
[Thr 11912] *** ERROR => NiPBind: bind failed (socket=131160) (0: No error) [ninti.c 942]
[Thr 11912] *** ERROR => NiIBind: service '1080' (1080) in use [nixxi_r.cpp 3860]
[Thr 11912] *** ERROR => NiIListen: NiBind (rc=-4) [nixxi_r.cpp 767]
[Thr 11912] *** ERROR => IcmBindService: NiBuf2Listen failed for host dlwsdv11:1080 (rc=-4): NIESERV_USED [icxxserv.c 1549]
[Thr 11912] ISC: created 400 MB disk cache.
[Thr 11912] ISC: created 50 MB memory cache.
[Thr 11912] HttpSubHandlerAdd: Added handler HttpCacheHandler(slot=0, flags=12293) for /:0
[Thr 11912] HttpSubHandlerAdd: Added handler HttpSAPR3Handler(slot=1, flags=4101) for /:0
[Thr 11912] HttpSubHandlerAdd: Added handler HttpJ2EEHandler(slot=2, flags=1077253) for /:0
[Thr 11912] =================================================
[Thr 11912] = SSL Initialization on PC with Windows NT
[Thr 11912] = (640_REL,Jul 16 2006,mt,ascii,SAP_UC/size_t/void* = 16/32/32)
[Thr 11912] SapISSLComposeFilename(): profile param "ssl/ssl_lib" = "D:\usr\sap\CC5\SYS\exe\run/libsapcrypto.so"
resulting Filename = "D:\usr\sap\CC5\SYS\exe\run/libsapcrypto.so"
[Thr 11912] *** ERROR => DlLoadLib: LoadLibrary(D:\usr\sap\CC5\SYS\exe\run\libsapcrypto.so) Error 126 [dlnt.c 237]
[Thr 11912] Error 126 = "The specified module could not be found."
[Thr 11912] *** ERROR => secudessl_LoadLibrary(): Unable to load "D:\usr\sap\CC5\SYS\exe\run\libsapcrypto.so" [ssslsecu.c 352]
[Thr 11912] *** ERROR => Loading of SSL library failed -- NO SSL available!
[Thr 11912] =================================================
[Thr 11912] <<- ERROR: SapSSLInit(read_profile=1)==SSSLERR_LIB_NOT_FOUND
[Thr 11912] *** ERROR => IcmAddService: SapSSLInit (rc=-1): SSSLERR_LIB_NOT_FOUND [icxxserv.c 348]
[Thr 11912] Sat Jul 26 10:52:05 2008
[Thr 11912] Started service 1025 for protocol SMTP on host "dlwsdv11"(on all adapters) (processing timeout=60, keep_alive_timeou
[Thr 10492] IcmJ2EEScheduleFunc: WARNING: no HTTP and HTTPS service defined - URL Prefix Table not loaded from server
[Thr 11912] Sat Jul 26 10:52:14 2008
[Thr 11912] *** WARNING => IcmNetCheck: NiAddrToHost(10.0.0.1) took 9 seconds [icxxtool.c 1065]
[Thr 11912] *** WARNING => IcmNetCheck: 1 possible network problems detected - please check the network/DNS settings [icxxtool.c
[Thr 10188] Sat Jul 26 10:53:50 2008
[Thr 10188] MPI<3>0#4 Peak buffer usage: 2 (@ 64 KB)
Please guide me on this.
Appreciate your help.
Thanks,
ChandravadanHi
Check for HTTP/HTTPS service status:
go to transaction SMICM
SMICM->goto->services
do you see HTTP protocol is maintained and active?
Also check this link for various ICMAN related issues
http://help.sap.com/saphelp_nw04/helpdata/en/ba/435e096b42724bbcef709fd4c32a85/frameset.htm -
For 0PS_C02 cube Project System - Dates update rules not activated!!
Hi All,
When we are trying to install update rules from the BI content for PS module for the cube "0PS_C02 Project System - Dates", the
update rules are not activating. under the cube when BI content activation. What is the issue in activating the update rules from BI content. From BI content the available version objects only will be activated i think. Please rectify and resolve the same at the earliest friends.
thanks,
SakaliHi,
Try to activate through program RSAU_UPDR_REACTIVATE_ALL. -
FI documents effect when controlling was not activated
Hi Experts,
I have one issue regarding when the controlling was not activated.
I posted some FI documents relating expenses etc. that time contrllong module was not configured. Now controlling was configured. Can i show that expense documents effect in controlling which are posted in FI previously.
Thanks and Regards
BaluHi,
If the controlling Module is activated subsequently, the earlier will not get updated automatically. System will not be able to identify to which cost center the document should get updated.
Probably, some custom program needs to be used to update the Cost Centers for the earlier documents.
Thanks
Murali.
Maybe you are looking for
-
Opening Pages 2.0 documents with Pages 1.01
I cannot seem to figure out how to open a page on my work computer with Pages 1.01 that I saved on my home computer using Pages 2.0. Could there be a possible integration problem with the two different versions? Everytime I click "Open File" it says
-
Hi, We have a system in legacy where we have the policy of signing of cheques based on authority i.e. a cheque of say upto 25000 can be signed by M1 grade, 25001 - 100000 by M2 grade & so on. How can i replicate the same concept in SAP. Requirement:
-
Is there a plug-in similar to next tab for v3.6.18
Is there a plug-in similar to next tab for v3.6.18?
-
Metadata fields like Tags, page ID etc not available for a Content in Content Server info.
Hi, Am trying to build a Webcenter Portal application with the help of a tutorial. This requires to upload files to Content Server and use these files to build the app. and to link the navigations for menu and sub-menus. I have checked in the files m
-
When opening previous office version excel files it saves instead of opening
Hi there, Recently I installed Office 2013 and deinstalled the previous version Office XP ( aka Office 2002 ). I tried to open some xlsm files but when I open it by double click on them it opens a "save as" screen... It is an XLSM file that is locate