C4795 Wireless Printer keeps dropping connection...what am I doing wrong??
Hey everyone. I have an HP C4795 Wireless printer and am using a Cisco Linksys E1000 wireless router (very new). I continuously loose the connection to the printer, even though the router, printer, and my computer are in a 10 foot radius of each other. I can connect the printer to my computer via USB and it prints perfectly, but the whole reason I got it was for the wireless functionality. I am running Windows 7 on one laptop, and Windows XP on the other, same problem with both. When I restart the printer/router, it will find it for a little while, and then loose connection (again, same on both laptops). I know this issue has been discussed, but is there anyway to "jump start" the printer to "reconnect" to the network without having to manually restart the printer/router (or hook up via USB)?? I am so lost. I have tried everything. I just want the printer to not go off the network and I'm lost...ANY HELP??? THANK YOU!
Merry X-Mas and Happy Holidays!
-Tom
This question was solved.
View Solution.
Nevermind, figured it out by reading this thread (if people are having the same issue). The only thing to add to these instructions is that you are going to have to add the printer again, after changing to manual IP address:
http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/SOLUTION-to-your-HP-printer-going-offli...
Happy holidays all!
Similar Messages
-
Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff -
Why can't I connect to Exchange Server 2003? I'm using OS Lion. My iphone connects, what am I doing wrong?
the iPhone uses active sync. Desktop clients do not. Desktop clients use another exchange protocol (which i can't remember as i'm not a microsofty).
Just because you can access via active sync doesn't mean you can access it by other methods, and vice versa. -
I'm in Final Draft (screenwriting prgram) and hit Save as PDF and a window opens stating that the printer name is invalid - what am I doing wrong?
Final Draft, Inc. - Search: printer name invalid
-
After I retouch a pic, it won't print with the retouches. It still prints the original pic. What am I doing wrong?
There are 9 different versions of iPhoto and they run on eight different versions of the Operating System. The tricks and tips for dealing with issues vary from version to version and OS to OS. So before anyone can help, they need information to work with. Things like:
- What version of iPhoto.
- What version of the Operating System.
- Details. What were you doing when the problem arose?
- Did it ever work properly?
- Are there error messages?
- What steps have you tried already to solve the issue.
Anything else you can think of that might allow someone else to understand your issue. -
Printer keeps dropping wireless connection after working for a while
My computer stops being able to communicate with the printer wirelessly even thought the printer says it is connected to the network and both the printer and computer are on the same network. What happens is I connect the printer to the network and print something from my computer. Then, after a short while, half an hour maybe, when the printer shows it is connected to the network, I try to print but my computer can't find the printer. The message say the printer cannot be found. If I go to the printer, and reconnect with the wireless connection wizard I can print. But after a short time, I won't be able to print again and have to do the wireless connection wizard again. Wireless direct is off. Don't know if that matters.
These settings are for setting up your wireless printer to stay connected to your router, keep wireless devices better connected and makes your router secure and hack proof.
Set a static IP in the printer (click here) outside the DHCP range of the router (check your manual). This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed. More Wireless Printing help is here (Windows solution 4, static IP).
Verify in the printer that 'Auto Off/Sleep' is disabled. Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off. Or use the Printer Assistant, Printer Home Page (EWS). Also check your Printers Properties.
If the printer supports and has IPv6 enabled, turn off IPv6 in the printer.
If needed and you assigned a static IP address, try using 8.8.8.8 for the Preferred DNS server and 8.8.4.4 at the Alternate DNS server.
In the router: (Refer to your router manual for information)
Use a fixed wireless channel like 1, 6 or 11, never 'auto', try channel 1 first then the rest.
Set router to 20Mhz only, or 145Mbps depending on router.
Always use WPA2-AES (Personal) encryption, but you can try ‘mixed’ mode.
Disable WPS and never use it and disable UPnP for the routers security. Nobody can hack your system now and helps with wireless connectivity (if you want to know why, search the web).
If you have a dual band router (2.4Ghz and 5.0Ghz bands), make sure the SSID’s are NOT the same, they must be different for all bands, even for any Guest networks.
SSID broadcast must be enabled.
Save all settings. Power off both, wait 2 mins. Power on router wait 2 mins.
Power on printer and verify it reconnects to router.
Windows 7/8/8.1 Is Network Discovery on or off?
Control Panel/Network and Internet/Network and Sharing Center/Advanced sharing settings.
Under Home or Work (current profile) / Network Discovery.
Select "Turn on network discovery" and save changes.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
My wireless printer keeps going offline--how can I "stabilize" the connection"
my wireless printer keeps going offline--how can I "stabilize" the connection?
This question was solved.
View Solution.Hello gerrie,
What i would do is Power cycle the printer and the router as well
-basically having them turned off for about 10-15 seconds
-and then powering back the router back on wait for all the lights to turn on completely
-and after that is back up and running i would turn the printer back on and re-establish the connection between the printer and the Wireless network
I am an HP employee.
__ if this Solution has helped Please Mark as Resolved and feel free to Provide a Kudos__ -
Everything I own (iPad, iPhone, mac) is set up on wi-fi. when i bring my work computer home (dell laptop), I cannot get it to keep the connection in a different room. All my other devices work.... does anybody know what i am doing wrong? please help!
Windows drivers for Intel wireless cards are known problematic.. If you have plenty of signal and it still cannot keep or hold the connection the issue can simply be the type of wireless.
Another problem is using names that windows does not easily handle.
eg If you set the TC using apple names, like
Fred Blog's Airport Time Capsule wireless24ad12
Then to windows this is too long.. it has spaces and it has illegal character.
Change all names on the TC to suit windows. Short, no spaces and pure alphanumeric.
Also security must be suitable.. I have no idea how old or what OS your dell is, but if you still have issues.. pull off the security on the TC for a test.. if the computer suddenly works, it is not compatible with WPA2 AES. Make sure you also use a password that is mix upper and lower case plus numbers.. avoid special characters and make it 10-20 characters long say.. it is not required to be more than that unless you are paranoid. -
While my Library is turned on in iTunes, I keep getting the following message from my AppleTV: "Could not connect to Chuck's Library." What am I doing wrong. I am a newbie, just getting started. Ultimately, I'm trying to get everything linked up so I can view My Picture on TV (via my wireless network - of course).
Thanks for any help you can provide!Welcome to the Apple Community.
Does your Firewall allow access for iTunes, do you have any security software installed, is your network working correctly. -
Wireless devices keep dropping, Wired works 24/7
Hi,
We have had bt infinity in our home for a few months now, and only in the past few weeks we have been having constant problems with wireless devices. We have one computer wired, one wireless and a few other devices such as tablets phones etc. The connection on all the wireless devices keeps dropping with no response, while the wired one is still working perfectly. The problem is becoming more frequent than ever, I spoke to tech support at BT who told me to log onto my router and change the channel to 11 but since then, zero improvements.
When i troubleshooted the internet connection problem on the wireless pc, i got the message
" internet connection doesnt have a valid ip configuration"
Can anyone help? or is my hub giving up the ghost?
Thanks!There is some help on this page.
Wireless connection problems
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
Wireless printer keeps linking up with neighbors router
My wireless printer keeps linking with my neighbors router when I turn it on, even though it's sitting right next to my router. If I ask my neighbor to turn his router off then my printer will link with my router. What's happening here and how can I fix it?
You can try to set the security on your router and input all the wireless settings on your printer manually. So it will not keep on linking with your neighbors wireless network.
-
Hi, just bought my daughter an Iphone 4s and I can't get it to let her on youtube, Facebook etc., keeps saying no internet connection. My husband and I have 3G smartphones and we can get on them on ours, so I'm not sure what I'm doing wrong. Also, my other daughter has the same phone and has no trouble getting on these sites either. Any information to help is greatly appreciated. Thanks
Well, did you activate this new phone?
-
HT2845 why does my wireless mouse keep losing connection?
Good morning,
My wireless mouse keeps losing connection...my batteries are at 100% and the "discoverable" option is checked off. Why is this happening?Hi:
PRAM=parameter random access memory - reset like this:
http://support.apple.com/kb/PH11243
SMC=system management controller reset like this:
http://support.apple.com/kb/HT3964
Sometimes resetting these "fixes" odd problems - and it cannot hurt.
To make a device a favorite, go to system preferences>bluetooth. Highlight the device. If detailed information is not shown, click oin the little gear>show more info. Then click on the gear again and make the device a favorite.
Barry -
My IPAD software update is avail for the iOS 7.0.3 I keep trying to install it. I have my IPAD hooked up to my MAC and the Wi FI, I have internet open It keeps telling me not connected to internet. What am I doing wrong.
You can try resetting your iPad by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists. -
Hi I have an iPad with iOS 612 and am trying to connect a wireless printer, I don't think it's doing it because I don't have iOS 10 or more. Is this right?.
If you want to use AirPrint - the buit in feature in iOS that allows you to print directly from the iPad without another app - you need to be using an AirPrint Printer. There is a list of those printers here.
AirPrint basics
If your printer is not on the list, you may still be able to use your current printer, but will need to purchase a printing app for the iPad from the App Store.
I don't understand you reference to iOS 10 unless you mean OS X10 for Mac.
Maybe you are looking for
-
I was on here 11 months ago with the same encoding problem, where it would get to the encoding part of the burning and would stop, then up would pop up the "Open Finder" box, the one where it says you have put in an empty disc and would you like to e
-
I have just upgraded to iTunes 11.0.5 and it won't recognize my devices
I have upgraded to iTunes 11.0.5 and now iTunes won't even recognize my devices so I can't sync my apps, etc.
-
Printing to Acrobat 9 Pro renders giberish text
When printing from the net to my Acrobat 9 Pro the image output is perfect yet the text is all giberish. Can anyone help? Thanks in advanced. Francisco De La Chesnaye [email protected]
-
I started working on my personal portfolio website today with Reflow, so this thread is dedicated to everything that I find unintuitive in Reflow or feature requests I would like to see implemented. Font Aliasing is really bad. I miss a zoom tool! Sh
-
I just purchased a mac pro, and have downloaded a dvd video which I created with a tivo dvr system. The dvd will play with idvd, but I can't get the video to open in idvd, or with final cut express, as they will not recognize that file format. Any su