C90 only making audio calls

Hello ,
I just purchased and setup two C90s . Calling to other endpoints or inside my network between these two I only get an audio call. I have gone over everything 100 times and I just cant seem to find the issue. I have used the C series codecs for years and have not seen anything like this before. It will not push a presentation either.
Thanks

Thanks for the response !!
I have put these two all by themselves on a small network and am trying back and forth between the two with no other influence . Yes , they are acting just like a unit without multisite that is already in an active call.
They are both set to 4 meg and they are the only devices on that network. There is one caveat and I havnt mentioned it because I have done it a thousand times and it never mattered . I am not using the Cisco camera with camera control and I do have the error for no camera attached.
I have seen this tons of times in the past and it didnt matter at all. I usually hook a high end camera into the HD/SDI input for what I use these for.
These are older "Tanberg" branded codecs tho and I am wondering if it puts the units into a state where they cant make a video call ? I looked for some API command to disable such a thing if it existed and found nothing. Im dying here.

Similar Messages

DX80 making Audio Calls Only

I have just recently acquired a DX80 to test in our environment. I was able to get it registered to CUCM 10.5 and place calls with it. The problem is though that it will only make Audio calls. I cant seem to get it to make any video calls.
All the other devices (SX20s) registered on CUCM can make video and audio calls without any issues.
I have installed the device pack.
cmterm-devicepack10.5.2.12014-1.cop.sgn
and the device
cmterm-dx80.10-2-3-33.cop.sgn
Running with:
CUCM 10.5
VCS 8.5.1
Any suggestions?

Thanks for the response !!
I have put these two all by themselves on a small network and am trying back and forth between the two with no other influence . Yes , they are acting just like a unit without multisite that is already in an active call.
They are both set to 4 meg and they are the only devices on that network. There is one caveat and I havnt mentioned it because I have done it a thousand times and it never mattered . I am not using the Cisco camera with camera control and I do have the error for no camera attached.
I have seen this tons of times in the past and it didnt matter at all. I usually hook a high end camera into the HD/SDI input for what I use these for.
These are older "Tanberg" branded codecs tho and I am wondering if it puts the units into a state where they cant make a video call ? I looked for some API command to disable such a thing if it existed and found nothing. Im dying here.

Lync 2013 stops responding when making audio calls

Lync 2013 desktop client in Windows 8.1 connected to Lync Server 2010
From my office workstation (Windows 7, Lync 2010 client, completely different hardware), from inside the firewall, I don't have any problems (IM, audio, conference, video, desktop sharing all work 100%). At home, I haven't been able to make PC calls.
I can see the status of my contacts in Lync, and contact them through IM, but as soon as I try to make an audio call, Lync stops responding. I can, on occasion, connect and can receive audio, but I cannot be heard on the other end.
To place audio calls, I connect to my office workstation through remote desktop - the audio quality is terrible but it works.
I'm testing various configurations using the "Check Call Quality" function under Tools > Audio Device Settings. I can hear a couple of beeps, or even a ring tone, once, but then it crashes again. Waiting 10 to 15 minutes, it still
does not respond.
I am using Lync 2013 because 2010 wasn't available through MS Office HUP. I checked the compatibility list, and I didn't think there would be a conflict between the two versions.
Would downgrading Lync to 2010 help?
I am not exactly a Lync expert, so I may have some of the setup wrong. I'm hoping it's as simple as a server/connection setting that I've missed. I'm using Automatic Configuration under Advanced Connection Settings.
Hardware specs:
DELL XPS 8500
Windows 8.1 64-bit
Realtek High-Definition ALC887 Audio
Creative Labs Sound Blaster Recon3D PCIe Audio Card
NVidia GeForce GTX 660 Graphics Card
According to Windows, all drivers are up to date.
I had a Logitech webcam installed. I disconnected it and restarted the computer, to make sure it wasn't affecting Lync.

Hi,
Did the issue happen only for you or for multiple users?
Did the issue happen when one endpoint is internal and the other is remote or also happen when two endpoint external the company?
If it possible, please try to use another computer login on Lync client 2013 at home.
Please double check if you have configured DNS entry for Lync server Edge A/V service.
Here is a similar case may help you:
http://social.technet.microsoft.com/Forums/lync/en-US/522e7f53-d0d4-4b08-9917-45b80a292963/lync-2010-external-voice-calls-do-not-complete-call-failed-to-establish-due-to-a-media?forum=ocsedge
Please also double check the Edge external A/V port UDP 3478, TCP 50,000-59,999 and UDP 50,000-59,999 and make sure they are opened.
What’s more, you can troubleshooting Edge server with the help of the link below:
http://blogs.technet.com/b/nexthop/archive/2011/12/07/useful-tips-for-testing-your-lync-edge-server.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

IOS7 Bug: Why is that i can only making an call works from notification area without unlocking the Phone using the passcode

Hi,
After upgrading to iOS7, I was asked by the system to set an passcode.
When i try to swipe from the notification area, it navigates me to the passcode lock screen which is expected but the same behaviour is not shown for a call - when i swipe from my notification area for the missed call it allows me to make calls.
Is this a bug or expected behaviour? Why there is a different behaviour for different functionalities? Its just to confuse the users?

It sounds as if you only had one line with an upgrade available. So you can only upgrade one line. For you to upgrade as well, you will have to wait until your upgrade is available. You can check that at MyVerizon. That's just how it works. All carriers and phone brands are the same. I have to wait until February to upgrade. The only thing you can do to get the new iPhone, is add a new line. But then you're paying for a line you don't need.

Problem with audio while making a call

I have a model 9810,
I can hear no audio while making a call at all, however, while making the call if I press the speaker tab I can hear (as like a hands free made)
I do not use a head set or in car kit, I just use it as a handset.
All other audio is OK, I can hear the alerts as a call or text comes in, but as soon as I answer the call and place it near my ear I hear nothing
Can someone please help
Thank you

Hello,
Questionz wrote:
I am having the exact same problem, I am not sure why, but my ear speaker is not working. I tried resetting, removing the battery, but nothing seems to be working.. Putting the call on speaker works, bluetooth works, only my ear speaker is not working.
I recommend that you attempt to boot into Safe Mode:
KB17877 How to start a BlackBerry smartphone in Safe Mode
It may take you multiple attempts to get the ESC key sequence (press/release/hold) correct, so be patient. When successfully into Safe Mode, see what happens.
If the behavior ceases, then think carefully...what happened just before this behavior started? A new app? An update? A Theme? Something else? Think carefully as the smallest change could be causal...and attempt to undo whatever that was.
But if the behavior continues in Safe Mode, then you may need to consider more drastic actions -- WIPE, OS Reload, BBSAK Wipe/Reload, and the "Bare Bones" OS Reload Process. To prepare, you should be sure that you have a full backup to your PC...please review the Backup link in my auto-sig on this post for instructions.
You may also need the use of these tricks:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
Questionz wrote:
I bought this from Blackberry store, is there any way I can give this in as warranty?
When you purchased, you should have received information as to how to seek support, warranty or otherwise.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I have one iPhone 8GB. after making upgrade of iTunes and software of iPhone, it's impossible to use the iPhone. There's no service! doesn't acept the code PIN! it only make emergency calls and the image in the phone is to conect to iTunes.What can i do?

I have one iPhone 8GB. After making un upgrade of iTunes and software of iPhone, it's impossible to use it. There's no service! doesn't acept PIN code! it only makes emergency calls and the image in the iPhone is the sign to connect to iTunes. What can i do to solve it?

Where are you and where did you get the phone. This sounds like a classic symptom of someone who bought an iPhone that originated in the U.S. which was then hacked so it would run on a carrier network other than AT&T... Then, when updating the phone, it becare re-locked to AT&T.
If that's what happened, you now own a paperweight. AT&T will NOT unlock them for any reason.
If this isn't the case, please clarify where you are, what carrier you have and where you got the phone so we can begin troubleshooting.

I was making a movie on iMovie, and was trying to use the green screen to make a split screen. I pressed on the green screen button, but the second clip didn't play next to the first, and only the audio played.

I was making a movie on iMovie, and was trying to use the green screen to make a split screen. I pressed on the green screen button, but the second clip didn't play next to the first, and only the audio played. I tried again with some different clips and some worked and some didn't. This hasn't happened before. What should I do? (I am using iMovie '09)

No guarantess but try smc and pram resets,

Why is my backlight display lit for only 5 seconds while making a call (Brightside phone)

When I go to settings, I see that it is set for 2 minutes and indeed it does stay lit for that amount of time if I am not making a call, but as soon as I dial a phone number and especially when I get into an automated menu system where I need to press 1 to get to a different menu and then other numbers to finally get to talk to someone, the display goes black. I have tried swiping the screen which does not help. The only thing that I can do is press the curly arrow that points to the left to have the display light come back on for another 4 seconds, then press the button called keypad and hurry and press a number to continue with the menu system.
I talked with Verizon and was told can do a complete reset, but I don't want to lose my contacts. I went to backup assistant online but keep getting the arrows that go around and around forever and won't let me see if they are backed up. I want to view my contacts online and I want to print them. What's wrong with that site?
I will say this. Do not buy the Brightside phone. It is not a smart phone. It's a touch phone and when you touch anything, things come on like the camera or makes calls to my favorite contacts. sheesh! I can't wait until our contract with Verizon is over with.

I just bought the phone yesterday and have noticed the same issue. The verizon guy i just spoke to said that needed to be fixed, so he transferred me to Samsung tech support. I'm waiting for them to pick up . . .
Okay, spoke to a very nice person who concluded that this was not an option that could be adjusted. The light apparently stays on for about 6 secs.
I was hoping it could be changed, so that's disappointing, but the reason it goes dark makes a lot of sense: it keeps you from hitting buttons accidentally while you're on the phone, so you can hold the phone in your hand, to your ear, etc. without worrying about activating something unintentionally. Also saves battery.
Hope this was helpful.

I phone 3 just shuts down after 3 to 4 mins when making a call large apple logo apears on screen the only way to reboot is to charge charge it although there is enough battery.any answers thanks

i phone 3 shuts down after 3 to 4 mins when making a call - then large apple sign apeers phone frozen - only way to unlock is to re charge although there is enough battery - any answers would be welcome.

The Basic Troubleshooting Steps are:
Restart... Reset... Restore from Backup... Restore as New...
Restart / Reset
http://support.apple.com/kb/ht1430
Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414
But... This can happen if the phone has been Hacked / Jailbroken / Modified...
If this is the case... Then... None of the above will necessarily work...
And...
The discussion of Jailbroken Devices is against the Terms of Use of this Forum.
You will need to look elsewhere.

May ipod touch can only recieved IMs. It can not call or recieve any video and audio calls, please help. thanks

may ipod touch can only recieved IMs. It can not call or recieve any video and audio calls, please help. thanks

Maybe try here:
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
What apps are you using?

Is there a way to switch off by default the video on FaceTime? I only ever use this app for audio/calls and hate the video being on. I especially hate that if I leave the app open to receive calls it means the camera and green light are on.

My issue is that I can't find a way to have the camera switched off when the app is open and so this means if I want the app open all day to receive calls then the camera is going to be on the whole time. Even if it didn't potentially drain the battery, or add to the CPU usage or whatever else may cause any problems whatsoever (wheel of death!), I just don't want the camera on as I don't see myself ever wanting to use the video call feature but I would use the audio/call multiple times throughout the day to make and receive calls. The camera being on when the app is open is enough to prevent me from using the app. Also ever since seeing that episode of criminal minds where if you saw the green light on above the screen then it meant the killer was watching you!
Basically I just can't believe there isn't a way to disable the camera whilst having the app running. I know when initiating an audio call the camera goes away, but I would like the camera away the whole time. To me it just would make sense that if you click the video option then the camera is on, and if you click the audio option then the camera goes off. It just seems waaaaay to basic a thought for apple to have missed... Let's face it, we're not all as pretty as the people in the apple adverts and don't want to see our ugly mugs staring back as us when we work all day at our macs!

I have exactly the same concern. It seems it would be a simple fix for Apple to allow users to turn off the camera (and even the mic) while keeping FaceTime open -- especially now that it turns out FaceTime must remain open in order to send and receive iPhone calls on a Mac.
I like to think this new functionality of FaceTime will be baked into a future release of Yosemite, as the current setup has that not-quite-finished feel of a work in progress. In the meantime, there's nothing like a little piece of Post-It stuck over the camera to keep the NSA from watching your face as you type a post to the Apple Support Communities.

Skype crashing computer when making a call

when making a call on skype whole computers freezes and cant click on anything.
Attachments:
DxDiag.zip ‏12 KB
DxDiag.zip ‏12 KB

SteveSkypeHelp wrote:
Hi there
I upgraded to the latest Skype v7.6.64.105 - ever since my Skype crashes when I make a call - oddly I get "not responding" but the call continues - I cannot press any Skype buttons during this time - when the call ends - the other person needs to hang up - then my Skype crashes and needs to restart.
I've uninstalled, restarted, reinstalled.
Cleared the %appdata% Skype folder - renamed this folder - had Skype recreate this folder.
I've done a system restore - same issue - then uninstalled/reinstalled.
Windows was upto date prior to system restore - then performed updates again.
My video drivers are up to date. Checked dell for updates - updated bios.
Reading on other boards - people are advised to run DxDiag - which I did and have attached. Skype seems to continue to work as expected when only using 'chat' - not audio.My audio devices drivers are up to date too?
I am at a loss now - please can you help? Faulting application name: Skype.exe, version: 7.6.64.105, time stamp: 0x55916aec
Faulting module name: igdumd32.dll_unloaded, version: 9.17.10.4229, time stamp: 0x55653f61
Exception code: 0xc0000005
Fault offset: 0x0000d480
Faulting process ID: 0xa30
Faulting application start time: 0x01d0bf235fbdf760
Faulting application path: C:\Program Files (x86)\Skype\Phone\Skype.exe
Faulting module path: igdumd32.dll
Report ID: c91269b3-2b19-11e5-becc-60d819fe036d
Faulting package full name:
Faulting package-relative application ID: Many thanksSteve
Skype is crashing on Intel graphics driver. The error message indicates that the issue is with "Switching Graphics" (NVIDIA <-> Intel). There are no driver updates available for Windows 8.1 for your laptop on the Dell site. However, you can try to update the NVIDIA NVS 4200M driver directly from the NVIDIA site. http://www.nvidia.com/download/driverResults.aspx/86814/en-us

IPhone 4 updated from 6.0 to 7.1.2 and now the picture no longer appears when receiving or making phone calls. How do I fix this?

I updated the software for my iPhone 4 from 6.0 to 7.1.2 and now pictures (contact picture/picture ID's) no longer appear (take up the entire screen) when receiving or making phone calls. They only show in a small circle which is not convenient at all. How do I fix this, please?

You are welcome. I have seen numerous posts on this subject, so I suspect you are correct. It doesn't seem like a welcome change. You can send feedback to Apple at http://www.apple.com/feedback/iphone.html

500 INternal server error on making ajax call to method of Application page

HI
I have a application page that have a method in code behond ..i need to call this method on usercontrol using jquey on client side..when i ma makeing the call to method using $.Ajax({definiotion});
then it gives me error 500 internal server error and this is coming only with the case when i am passing parameter to method usig javascript var object
help me out on this... if required i wll upload the code also..
regards
Piyush
piyush mishra

This forum is for customization and programming of Microsoft Project - the project management scheduling product.
A quick search turned up:
https://forum.jquery.com/
I'd try there.

YouTube films are only playing audio, no pictures any ideas out there. Mike D

YouTube films are only playing audio, no pictures. Any ideas out there I have already cleared out my Safari history as suggested in another post, this solved the issue for a day but back to square one now.

I am having the same problem. Last night during a long call using headphones, suddenly I could not be heard, but I could hear the person I was talking to. I did not try the speaker. This morning with out the headphone twice I placed a call and heard no ringing, but the call did connect as I was told they got the call, but no one was there. I just reset the phone and will see what happens. I was thinking of going to the Apple store were I got the phone, but if they are going to ship it off rather than exchnage it, that is a no go for me at this point.
Howard

C90 only making audio calls

Similar Messages

Maybe you are looking for