CA-42 cable drivers and Windows 8 (x64)

Hi,
Are the CA-42 cable drivers compatible with Windows 8 available?
The ones that I have on a CD worked with Windows XP, but I don't think they'll be good for Windows 8.

Abi99 wrote:
Mhm. That helps a lot actually.
In the Windows Control Panel » Software, what is the version of your Nokia Connectivity Cable Driver: 7.1.182?
In the Windows Device Manager, was a Modem generated for your Nokia 6610i?
This rules out PC Suite and Nokia Suite, and allows us to concentrate on the USB cable driver. If no modem was listed for your phone, please, attach your Nokia 6610i and have a look at the USB devices. Is there any yellow mark? Context-click on that and refresh its driver. If that does not help: Are you sure, you have an original Nokia CA-42?
I can't see a "Software" category in Control Panel in Windows 8, so I can't check the version of my Nokia Connectivity Cable Driver.
Do you mean "Uninstall or change a program" in Control Panel?
No modem in Device Manager after connecting the phone. Does it need to be created? As far as I remember from Windows XP, no modem was created and the connection was initiated and worked OK.
No USB devices with a yellow mark, either.
The cable is, in fact, DKU-5, but it worked fine with this 6610i on Windows XP.
I read on other forums that you have to install virtual COM port emulation drivers for this cable.
I have the drivers on the original CD that came with the cable, and they were installed on Windows XP (x32) a few years ago and worked OK, but I don't think they will be compatible with Windows 8 (x64). Am I right?
Please note that I don't need a connection with a PC to use internet. I just need to transfer data (mainly text messages) from the phone to a PC

Similar Messages

My solution for No Audio -- Conexant drivers and Windows 7 x64

My son and I have the L2000 laptop that came with 32 bit XP and used the Conexant chipset for Audio. I had been using an SB Audigy PCMCIA card so I am not sure when Audio was really lost; however, he noticed it when I upgraded his PC. I scoured various forums looking for 64 bit Windows 7 drivers for Conexant audio but to no avail. Microsoft and Conexant both said that HP should supply the drivers. By the way HP, the Conexant website says that they do not supply drivers even though they make the chipsets "at the request of the OEM's." Another post said that HP was not going to supply these drivers for Windows 7. The solution from HP for my model and Windows 7 was the "HP Software Advisor" which was 67MB and totaly useless. It appears that this is a very common problem. Anyway, here is what you do:
First you need 2 files which ironically enough come from HP, they are SP35558.exe and SP35558.cva They contain the Conexant drivers for Vista x64. (I subsequently have found the 32 bit drivers and the procedure should be very similar except the files are SP34789.exe and SP34789.cva). Type the following into your browser address bar ftp://ftp.hp.com/pub/softpaq/ About half way down you will find the sub-directory with these files. Just right click each one and save to your desktop.
Double click SP35558.cva and tell Windows to use Notepad to open it. Scroll about half way down to "[Operating Systems]" and after "WV64UL=OEM" insert:
W764HB=OEM
W764HP=OEM
W764PR=OEM
W764UL=OEM
( For 32 bit systems use W732HB=OEM, etc.)
I next went up about 10 lines to "[System information]" and added
SysId3=0x3091
SysName3=HP Pavilion ze2000 series
SysId4=0x3096
SysName4=Compaq presario M2000 series
SysId5=0x3097
SysName5=Compaq Presario M2000 series
SysId6=0x3097
SysName6=HP Special Edition L2000 series
SysId7=0x3093
SysName7=Compaq Presario M2000 series
SysId8=0x3093
SysName8=HP Special Edition L2000 series
I got this information from another cva file on my PC at C;/swsetup/ This is the directory where HP updates default to.
After modding the cva file, I saved it to C;/swsetup/sp35558/
I then executed the SP35558.exe file. It did not work the first time -- I missed a line in my cva file. However, I then manually installed the Conexant drivers as follows and voila I had sound, nice crisp clear sound.
Under Device Manager, right click "Multimedia Audio Device" under "Other" and choose "Update Driver" Then" Browse your PC" and "Choose from a list". Select "Sound, audio and game controllers", then Conexant, then "Have Disk" . Browse to C:/swsetup/sp35558/ and open "cp6308Ba.inf" (64bit remember). Now choose "OK" and ignore any warnings about incompatibility, WHQL, etc. Give it plenty of time, you might think you are in a loop, but you are not. Congratulations, you are done.
This question was solved.
View Solution.

I thought that I would recompile my answer and then mark this thread as solved since it was not a post about a problem but rather how I solved a very common problem that might be of benefit to others.
My son and I have the L2000 laptop that came with 32 bit XP and used the Conexant chipset for Audio. I had been using an SB Audigy PCMCIA card so I am not sure when Audio was really lost; however, he noticed it when I upgraded his PC. I scoured various forums looking for 64 bit Windows 7 drivers for Conexant audio but to no avail. Microsoft and Conexant both said that HP should supply the drivers. By the way HP, the Conexant website says that they do not supply drivers even though they make the chipsets "at the request of the OEM's." Another post said that HP was not going to supply these drivers for Windows 7. The solution from HP for my model and Windows 7 was the "HP Software Advisor" which was 67MB and totaly useless. It appears that this is a very common problem. Anyway, here is what you do:
First you need 2 files which ironically enough come from HP, they are SP35558.exe and SP35558.cva They contain the Conexant drivers for Vista x64. (I subsequently have found the 32 bit drivers and the procedure should be very similar except the files are SP34789.exe and SP34789.cva). Type the following into your browser address bar ftp://ftp.hp.com/pub/softpaq/sp35501-36000 About half way down you will find these files. Just right click each one and save to your desktop.(The 32 bit files are in a different subdirectory at ftp://ftp.hp.com/pub/softpaq/sp??????-??????)
Double click SP35558.cva and tell Windows to use Notepad to open it. Scroll about half way down to "[Operating Systems]" and after "WV64UL=OEM" insert:
W764HB=OEM
W764HP=OEM
W764PR=OEM
W764UL=OEM
( For 32 bit systems use W732HB=OEM, etc.)
I next went up about 10 lines to "[System information]" and added
SysId3=0x3091
SysName3=HP Pavilion ze2000 series
SysId4=0x3096
SysName4=Compaq presario M2000 series
SysId5=0x3097
SysName5=Compaq Presario M2000 series
SysId6=0x3097
SysName6=HP Special Edition L2000 series
SysId7=0x3093
SysName7=Compaq Presario M2000 series
SysId8=0x3093
SysName8=HP Special Edition L2000 series
I got this information from another cva file on my PC at C:/swsetup/ (This is thedefault directory for HP updates.)
After modding the cva file, I saved it to C;/swsetup/sp35558/
I then executed the SP35558.exe file and voila I had sound, nice crisp clear sound.
The use of the cva file is to streamline the driver install and it is kind of cool if it works. If you cannot find it or you are not successful the first time or you do not want to bother with modding anything, do not worry, the manual install will work for sure.
Run sp35558.exe to extract everything and let it strike out. Then go to Device Manager and update the driver manually as follows:
Under Device Manager, right click "Multimedia Audio Device" under "Other" and choose "Update Driver" Then "Browse your PC" and "Choose from a list". Select "Sound, audio and game controllers", then "Conexant", then "Have Disk". Browse to C:/swsetup/sp35558/ and open "cp6308Ba.inf" (64bit remember). Now choose "OK" and ignore any warnings about incompatibility, WHQL, etc. Give it plenty of time, you might think you are in a loop, but you are not. Congratulations, you are done.
Hope this helps.

Re: HP 15-d053sr drivers for Windows 7 x64 not installed

Hello!
I have the same problem!!!
Notebook HP 15-d053sr, Product No. F7R72EA#ACB, Serial No. [edited by Moderator], Bios Version F.11
On clean install Windows 7 x64, Can't install all Chipsets, USB 3.0 and Video drivers! Error message: "This computer does not meet the minimum requirements for installing the software"
On clean install Windows 8.1 x64 Can't install "IMEI" (sp64344) driver and maybe more!
HP Support Assistant find only 4 drivers (Atheros Bluetooth, Wireless LAN, Synaptics TouchPad and Realtek Audio drivers)...
Need working, supported, compatible drivers for Windows 7 x64!
Please HELP!!!

Hi @Ainars_LV ,
Thank you for visiting the HP Support Forums. I'm sorry to inform you that your post has needed some editing to remove personal information such as the Serial Number in your Post. From our Rules of Participation:
Protect privacy - yours and others'. Don't share anything about yourself that you would not want to see on a road-side billboard. Don't post contact or other personal information-your own or anyone else's-or any content that you receive in one-to-one communications without the author's consent. For example, don’t post your computer’s serial # or contact information publicly, and do not allow someone you don’t know to remotely take control of your computer.
If you need people to contact you directly, either ask them to send you a private message or subscribe to the thread so you will be notified when there are replies. You may also click on your name anywhere in the forum and you will be taken to your profile page, where you can find a list of threads you have participated in.
Sharing personal email addresses, telephone numbers, and last names is not allowed for your safety. If you have any questions feel free to send me a private message in reply.
Thank you
George
I work for HP

T6100 with X-FI Titanium Fatal1ty Pro and Windows 7 x64

7T600 with X-FI Titanium Fatalty Pro and Windows 7 x64 Hello,
Please forgive me my bad laungage. Im writting this Post because i want to ensure i wont have any problem using configuration as i wrote in topic. So, are there any drivers for Windows 7 x64 (PL, Home Premium) for my sound card. Can i also use Creative Alchemy tool on Windows 7 x64. And do i need to use Alchemy on Windows 7, to gain EAX in games too? Can i also download and use PowerDVD with is deli'vered with the drivers? And what with Dolby Digital Li've? Is there a problem with activating and using it on Windows 7? And last question: Can i gain a 5. sound with my Creative Inspire T600 sound system and use it in game, and music listening?without any trouble?
I wish to apologize for that many?questions but this is very important to me. So can i use it all, and can i install it from my X-FI?Titanium?Install CD, or do i have to download it from Creative site?
Thank you very much for answer!
Thunderbolt (my real name is too hard for foreigners) ^^

Please refer to my reply on your post under Windows 7.

Need Drivers for windows 10 x64

Hello, I need the proper drivers for windows 10 x64 for my probook 450 g1 laptop. I got the drivers from this page: http://us-support.external.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5405166&swLangOid=8&swEnvOid=4192all the drivers are not present here like display, hot keys etc. So it will be very helpful to me if someone helps me to get those drivers. Thanks in advance.

From Boot Camp: System requirements for Microsoft Windows operating systems - Apple Support please use Boot Camp Support Software 5.1.5640.
You can use Boot Camp: Install or repair Boot Camp drivers for Repair.

Windows 2000 and Nokia Cable Drivers and PC Suite

Appears Nokia does not support Windows 2k. Even though their web page states the USB Cable CA-101 driver, Nokia_Connectivity_Cable_Driver_rel_7_0_2_0_eng.msi, per their line "Nokia Cable Driver for Windows 2000, XP and Vista" on the web page says so. frustrating. Already aware that PC Suite version 7 is not supported in Win2k.
Is there a driver out there for the USB Cable CA-101 that will connect to the phone running Windows 2000? and allow at least the sd memory card be accessed for data transfer and other functions? thank you.
phone: 5610 XpressMusic
OS: Win2k service pack 4

Hi exergonico,
Which device are you using? Do you have CD that came along with your device? Could you please Search(Google) for Nokia PC Suite 6.85 or 6.86 nokia pc suite version and install on your pc to check this issue?

IPhone 5 iOS 6.1.4 and Windows 7 x64 USB Driver Issues

Been pulling my hair out with this one for the last week or so and haven't had any luck finding anything on the forums or the web regarding a solution short of a full reinstall of Windows 7 which I am not prepared to do at this time; so hoping someone here can shine some light on this for me
I have a iPhone 5 that is updated to iOS 6.1.4 and a recently built Windows 7 64-bit machine. All of my other USB devices function fine (keyboard, mouse, Xbox 360 wireless receiver for Windows, and a Seagate 2TB external USB drive). I've downloaded the most recent version of iTunes, installed successfully and then attempt to plug in my phone to sync. I get the standard Windows *ding* that I've attached a device and 1 of 2 things happens (I haven't been able to determine what causes one reaction to happen versus the other): Windows will successfully install the 'Apple USB Mobile Device Driver' successfully and it will appear under my USB devices in Device Manager. However - iTunes will not recognize the phone and I cannot see it in Windows either. In the 'Devices and Printers' snap-in my iPhone will appear under 'Unspecified Devices' as the 'Apple USB Mobile Device'. The iTunes diagnostics fail to find a connected device so the tests fail. As soon as I unplug the device, the strangest thing happens: Windows will start trying to install a device driver and after a few seconds it will fail stating that the "MTP Device Driver" installation failed because the device was unplugged. iTunes also thrown an error "iTunes cannot connect to this iPhone" throwing error code 0XE8000065 (I've also seen error code 0XE8000085 as well)
After some finagling, I've managed to get Windows to recognize the device under 'Portable Devices' in Device Manager as an "MTP USB Device" using the generic driver. At this point, I've tried updating the driver and manually specifying the Apple USB driver located in the C:\Program Files(x86)\Common Files\Apple\Mobile Device Drivers which updates successfully but then changes the device to "Apple USB Mobile Device" and moves it under the USB Devices in Device Manager; and Windows nor iTunes can see it even still.
I've tried removing iTunes several times and ensuring that all remnants of the installation are gone (registry and folders on the installation drive) and have disconnected all my USB devices short of the keyboard and mouse and still I get the same results. At this point, I'm afraid that a re-install of Windows is going to be the solution; but it's a drastic one (I have a SSD drive where Windows is installed along with all of my games for faster load times/better performance and do not want to have to redownload\reinstall all of them) and I'm not prepared to undertake it at this time, which is why I'm posting here
I've used a utility called USBDeview that sees my phone is connected - so I know from a functional standpoint that my USB ports are good and working. I also know the cable is good too - my daughter's PC (Windows 7 32-bit with NO iTunes) immediately sees the device when I plug it in, installs the drivers, recognizes it as an iPhone and I can then see/browse it in Windows Explorer like I would normally expect. My work PC (Windows 7 64bit, NO iTunes) sees the device just fine as well. I would immensely appreciate anyone that has seen this issue or has any additional solutions I can try.
It's also worth mentioning that I've never used Kapersky antivirus so the UPPERFILTERS value in the registry that I've seen as a solution on some forums is not present on my machine. I'm using Microsoft Security Essentials as my antivirus (no flaming please lol - it meets my needs and is extremely lightweight, which is why I'm using it on a gaming rig) and it's not indicating any issues. I've also tried running iTunes as an administrator (even though my account is a local admin on the machine) and that does not have any effect either.
If there is anything I left out, please let me know; and I thank you in advance!

AphexTwin wrote:
- no Apple input?
Of course not. Didn't you bother to read the TOU of this forum? This is a USER TO USER technical support forum. Apple doesn't post here.

Lenovo X131e doesn't work with Prolific PL2303 based USB to Serial Adapter and Windows 7 x64

This is sort of a bug report. A Lenovo X131e with Windows 7 x64 and the PL2303 driver including 1.6, 1.61 and 1.7 will not successfully install the driver - Windows always reports "Driver Install Failed" on plug in to USB 3 or USB2 ports. However, putting a USB2.0 hub inbetween the USB to Serial Adapter and either USB port type makes the adapter work fine. This was not the case with the X130e. I'm not sure where to report this beyond this posting, but more of an FYI.

If the USB can be used for other equipment,
That may be compatibility issues for USB and Prolific PL2303.
Don't plug Serial Adapter when installing the driver,
Ofter installation, Connect serial adapter to see whether it is working normally.
I am a volunteer, don't work for Lenovo. I am a software engineer.
thinkpad x61t, os:win7 Awavo Software com port monitor serial port monitor

Audigy 4 and windows 7 x64 ever going to work together?

?for 2 weeks i've tried every combo of drivers. and bios updates for my mainboard.
Can i get my once so reliable audigy 4 card to work on windows 7 ? No.
my mainboard is asus p5kpl-am. disbaled on board sound and no joy.
I had trouble even in windows 7 finding the audigy card before i had to do a full REinstall to my annoyance!! of course It found it then. But it never worked with the latest drivers. get no sound out put and worse it crashed my system and wouldnt repair. so had to revert back to onbaord sound and reinstall again.
the card is fine i know this as i have chekd in otehr systems on XP. but is anyone else having similar probs with a similar system as me?
And yes I have 4gb Ram, why should this make a difference. and i have tried it with 2gb. No joy!!
Please help creative and shed any light on this issue . If i RMA my card will gjust get a new or refurbished Audigy4?
cheers guys and sorry for any grammer lapses,

install the support pack and now the sound? works strangely apart from GAMES. they chop and distort!!
no end to madness !!!! im gonna have to try all these support packs or is they any way to stop the distortion?

Firefox 4 and Windows 7 x64 Ultimate

Does Firefox 4 have separate version for Windows 7 x64 Ultimate?

Hello, I my ID is durestudios from the Mozilla Firefox Chat Contributors group. Your following problem may be solved, but I will have to try to fix the problem in many ways. I'm sorry if that can bug you.
My best recommendation is to chat (It's free to use, and you don't have to download anything. All you need to do is go to:
http://support.mozilla.com/en-US/kb/Live+Chat?new_chat
and chat *WHEN CONTRIBUTORS ARE ONLINE*. There is a time schedule on this at the side of the page.
First: Try deleting your cookies and cache. This can be done by clicking the Tools tab of the top of your Mozilla Firefox page, then clicking 'Clear Recent History' on the box that appears, under 'Start Private Browsing'. Then a box will appear. On the top of that box, it says 'Time range to clear' and next to it has a view of options. click on that view of options (It's a box) and 5 options will appear. Click on 'Everything'. After that, on the bottom of the 'Clear Recent History' box, there is a button next to the word 'Details'. If there is a white box under the word 'Details' don't click on the button next to the word 'Details'. If there is no white box under the words 'Details', click on the box next to 'Details'. Now, un-check everything (click on the small box next to the words in the small box, if you click that small box a small check appears. When the check appears, it will be 'checked', and if there is no check in the box it will be 'UN-checked'.) except 'cookies' and 'cache'. For 'cookies' and 'cache' check them. Now press 'Clear Now'.
If this doesn't work, chat with anyone at the Firefox one-to-one direct chat.

CS3 dds drivers and Windows 7 64bit issue

I have photoshop CS3 working however I can't load the dds drivers. I've tried everything see below. Anyone been able to load the Nvidia dds drivers?
What is the proper proceedure to effectively install the DDS files in CS3 in a windows 7 64 bit environment?
I tried the 32 bit and 64 bit files and when I use the 32 bit file i get an error opening up photoshop that says missing D3x9_43.dll, and I don't have the option to save in a .dds format. If I uninstall the dds 32 bit program the missing D3x9_43.dll error goes away.
When I load 64 bit version no errors but I still don't have the option to save in .dds format. Kind of frustrating..................
I've just uninstalled and cleaned CS3. I've done a new fresh load of CS3. What are the correct steps from here?
Which file should I download? etc.
Thank you in advance.
Ok, I've tried everything I can find.
I let the 32 bit dds program load to a seperate folder and manually transfered the files to the proper folders in Photoshop and still get the same results as above. I tried renaming them and removing the 32 extensions and still no go. I did the same thing with the 64 bit program and still no go.
The 32 bit program said it was still looking for the D3X9_43.dll file for some reason. I haven't tried downloading that file since I don't know where to put it.
Can someone please help me. Has anyone got the DDS files to work with CS3 and Windows 7?
Thank you
Bill

Got it fixed. I loaded the drivers from my old XP machine. drivers are from 2007. Don't remember where I got them from but they worked. I can save dds files again.
Thank you for the reply.

CS2 and Windows 7 x64 Pro -- some PS1 fonts don't appear in Photoshop.

Since purchasing a new computer running Windows 7 x64 Pro, several of my fonts no longer appear in Photoshop CS2. They were functioning perfectly on my previous system running XP. The particular fonts that do not appear are Type 1 fonts, but other Type 1 fonts function normally. Adobe does not provide support for CS2 on Windows 7 systems. Since I use Photoshop daily, any help would be much appreciated. Thank you.

For Win7 64bit Pro or Ultimate (or Enterprise?) this is ONE example of using Virtual XP
http://forums.adobe.com/thread/702693?tstart=0

Is there any documentation concerning Contribute and Windows 2008 x64

I have the impression that it may not be posssible to use
Contribute on Windows 2008 x64 Enterprise server.
Has anyone had any luck?
thanks

Hi PREM,
If I understand correctly, you want to use SQL Server Authentication log to SQL Server Integration Services.
Based on my research, only Microsoft Windows Authentication is available for SSIS. So we cannot use SQL Server Authentication log to SQL Server Integration Services. Besides, we can only add OS users in the DCOM Config permission area.
Reference:
Connect to Server (Integration Services)
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

HP Pavilion dv6-6b56er and Windows 7 x64 Professional

Hello.
I've purchased Pavilion dv6-6b56er with pre-installed Win7 x64 Basic, which is not convenient for me, because of it's lack in functionality. So I've made a full backup of pavilion's hard drives and deleted all software from it. Then I've installed Win 7 x64 Pro and confronted with some difficulties regarding drivers for USB 3.0. Everything else is working fine. I know, that HP do not responsible for any experiments with non-pre-installed software, but still I have some questions.
First of all, which driver I should install for pavilion's USB 3.0 ports? At downloads page I've found three different options:
1. Renesas.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-99763-1&cc=us&dlc=en&lc=en&...
2. NEC.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100224-1&cc=us&dlc=en&lc=en...
3. Fresco.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-102204-1&cc=us&dlc=en&lc=en...
and
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100237-1&cc=us&dlc=en&lc=en...
The first two have been installed (I mean they CAN be installed), the third one - doesn't install at all. So what's the reason of putting it on download page?
The more the merrier. When you try to install package with NEC driver, installation master tells you, that it's Renesas driver. So there is no NEC driver on the download page at all. Why I've payed so much attention to it? I've installed Everest, so I can find out what driver is needed. It tells me that I have "NEC uPD720200 USB 3.0 Host Controller". So, there is no available driver on download page for NEC chipset and we have NEC chipset inside.
Meanwhile Windows' Support center offered some NEC driver for USB 3.0 (http://ftp.hp.com/pub/softpaq/sp47501-48000/sp47677.exe ).
So, who is right?
The second question. If try to connect to USB 3.0 port some compound device (usb hub for example), then in "devices and printers" appear strange devices with label "No data". If Renesas driver has been installed then "USB 2.0 hub" appeared, and if Windows' proposed NEC - then "NEC Electronics USB Hub". The count of strange devices depend on number of devices connected to this compound device. This is my main problem - these strange devices.
So I came to the deadlock. Any ideas to solve this problem?
Any replies will be much appreciated.
PS. Sorry for my bad English.
This question was solved.
View Solution.

Is the following image what you see when you start the recovery manager with the disk? This is for the CyberLink type Recovery Manager within Windows. The windows for the external recovery manager should be similar. I will use the external Recovery Manager on my loaner dv7 notebook and post an image later on today.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

DFS and Windows 7 x64 strange behavior when trying to access a DFS link through mapped drive

I've manually mapped a network drive (Q Drive) to a DFS location. Whenever I go into "My Computer" and open the Q Drive it shows the DFS links but when I double click one of the links it randomly takes me back to the "My Computer" starting point showing my standard drive letters. If I click through the Q drive and the DFS several time it all of the sudden works. Sometimes this circle of clicking can go on for 5-10 times before it works properly.
I'm running the x64 edition of Windows 7. Any suggestions on how to make this work properly? Its very annoying.

GPO mapped namespace where you can't connect through the mapped drive letter but can connect through the DFS UNC namespace? Do you use access based enumeration?
I personally think it has something to do with network bandwidth, the security token and offline files. =)
You can access the namespace itself but not any of the linked shares (try checking the ACL:s on the shares and you get permission denied, but you still see them, ie they are listed).
I found a post sometime ago about corrupted/trunkated security tokens. If the member was part of too many AD groups the token was trunkated and corrupted. That was going to be my next move. Sniff the traffic and see what actually happens when the issue occur
if theres something to be learnt there. Since it works correctly through the UNC adress but not through the drive letter you ough to be able to see what is different between the two requests.
http://blogs.technet.com/b/askds/archive/2008/05/14/troubleshooting-kerberos-authentication-problems-name-resolution-issues.aspx
One thing I noted was that it only happened to remotely connected computers on slow 3G connections (we use Direct Access). Never on LAN-connected computers with GB access or remote computers with fast (>15Mbps) access. We also use folder redirection,
which I think could be part of the problem, ie the share never goes online, atleast for us the issue was itermittent, it never happend all of the time, just from time to time. And if I disconnected and reconnected it could fix the issue for that particular
sessions, usually it didn't but occasionally it did (just pulling the network cable and put it back). Check the offline/online status the folders show up as offline even though they are online.
Enough of my ramblings. Sorry to hear you still have the problem and I hope you find a way to solve it.

CA-42 cable drivers and Windows 8 (x64)

Similar Messages

Maybe you are looking for