Cable usb n78 problem
Hy guys,
Since i've bought my N78 i've never been able to connect the phone via cable USB. My computer doesn't recognize my Phone. The pc recognize the device only using Bluetooth or using the phone modality "mass storage", so I'm not able to do the updating of the firmware.
I reinstalled many times the last versions of PC Suite and Ovi Suite.
Any suggestion?
Uninstall all nokia software from your system, making sure that you also uninstall the "cable connectivity drivers", then reboot your system.
Next, Install only the nokia software updater from the link below and reboot if it asks you to.
www.nokia.com/softwareupdate
If that works you can then install PC suite.
If it still fails to work then it is most likely a conflict caused by another piece of software or hardware on your system. Tracking that down will be very difficult so make sure your PC is clean, up to date and only running the background apps that it needs.
Similar Messages
-
Hy guys,
Since i've bought my N78 i've been able to connect the phone via cable only one time. After that, every time i've tryed to connect my n78 via cable my computer doesn't recognize my Phone.
When I plug USB cable in one of the USB ports, Windows XP gives me back an error that says "USB devices not recognized - One or more devices connected to the computer has not worked correctly. Windows is not able to recognize it".
I've reinstalled PC suite thousands of times,but nothing changes.
My phone has the 12.046 software version. I know that there'e a newer version but how I can update it if my PC does not recognize the phone, and hence, PC suite is not able to connect to the phone.
Many thanks for you help
myou have another option in updating via Firmware Over The Air. you can do this by entering *#0000# in the standby screen and selecting Options > Check for updates. if an update is not available over NSU, then it may be on FOTA instead for your product code. this method of updating only takes about three to five minutes anyway. remember to do a hard reset (three-finger hard reset) after updating your phone to the new firmware.
so you can probably update from 12.046 to 20.149 or 21.002. USB connectivity problems are probably due to problems with the USB cable or the computer, i have had no problems at all with USB connectivity in all the time i've had my N78, even under 12.046 firmware.
let us know how it goes.
If you found this or someone's comments helpful or like what that person has to say, please give some Kudos to their post! -
bonjour , voila j'ai un énorme probleme , mon iPhone a un bug il reste allumer que quand je le branche et il reste juste sur le logos itunes avec le cable usb , je vais sur itune le réinsialiser et il me disent code erreure 21 , que doit-je faire ?
Bonjour du Canada!
Pour répondre à ta question concernant Balance, ton entreprise doit être parti d'une solution Entreprise pour activer cet service.
J'espère que ça t'aides.
(Excuse mon français, je suis Anglophone.)
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated. -
IPod nano 4gb LCD flash in white only with "detach the cable USB ........"
My iPOD 4gb have the completely white LCD.
After the procedure of iTune "Restore" this goes very well ,everything LCD it works I can listen the music, etc.
But!!! if I immediately detach the cable USB connected to the PC the LCD it becomes again white and I cannot see anything.
Please HELP... somebody know the solution ?
I don't believe that is a hardware LCD problem and if I’ll replace it with one new I think that the problem remains.
PLESE HELPDear torkildsen,
Please obtain the solution to the matter at the below.
1. Reset your iPod.
2. Retry with a different USB or FireWire port. (To verify whether your iPod syncs via FireWire or USB, see the table in the Additional Information section below.)
3. Restart your computer and make sure you have the latest software updates installed.
4. Remove iTunes from your /Applications folder. Then reinstall the latest version of iTunes software.
5. Restore your iPod using another Mac that is able to recognize it. See “Updating and Restoring iPod Software” in the user's guide.
Or you can use other backup software to transfer iPod contents to iTunes or computer. Follow this reviews about [how to transfer music/videos/photos from iPod/iPhone to Mac?|http://www.softwarebbs.com/wiki/IPod/iPhone/iPadTo_Computer_Transfer_%26_Backup_SoftwareReviews] It includes the transferring of music, photos, videos, SMS, Contact ect. between iPod/iPhone/iPad and computer(PC or Mac).
Have a good luck. -
HP Laserjet 4 Usb adapter problem
I recently switched my HP laserjet 4 from a parallel connection to a parallel to usb connector.
The drivers for both installed properly however the printer does not seem to print is there a specific port I need to use or is there another issue?
printer prints a test page fine as well.
Thanks in advance.Hi Moorty
Hi wm300
I have connected a HP LaserJet 4L to Mac OS X 10.3.9 using a Keyspan parallel to USB adaptor cable. You will require the same hardware setup. It is more than a connector, the cable it has a small converter card in it.
Keyspan parallel USB printer adaptor
You already have such a similar cable.
Your problem seems to be the right driver.
remove the printer then Add it again and decide which driver you want to use.
Your model HP will work with the drivers available in OS X, HP LaserJet 4MP, or the old driver downloaded from the HP website for the LJ4/4M will also work.
A new driver for it will also work available here
http://buymelunch.org/printing/usbtb/
So once connected to a USB port, your Mac will see it, load the right driver, and the printer should work.
regards roam -
This device cannot start (Code 10) with Rocksmith Realtone Cable (USB Audio)
Hi there.
Let me start off by saying that my problem is specific to only windows 8.1 64x and deals with usb devices.
My specs:
Crucial MX100 ssd
Win 8.1 Pro 64x
MSI Gtx 970
MSI Gaming 5 z97
i7-4790k
I'm trying to connect my Rocksmith Realtone cable (usb audio) to a usb port on my pc and whenI right click the "Usb audio device) in device manager, this pops up under properties. There is also a yellow exclamation mark on the device.
This device cannot start. (Code 10)
The I/O request was canceled."
Now, like I said, this is only on win 8.1 64x. I installed win 7 64x on an older hdd and put it in my pc and the cable was recognized right away and was usable. I have tried:
Manually uninstalling the device, and reinstalling
Manually installing the device driver
Formatted ssd and did a fresh install of win 8.1
Tried it on win 7 with same pc and it worked fine
Updated realtek drivers
Updated Nvidia drivers
Disabled xHCI in bios
Disabled legacy usb support in dios
Disabled eHCI in bios
Enabled usb powered hubs in bios
Disabled selected powering in power options + made a new high performance profile
Here are photos of the problem
http://puu.sh/gPfLJ/73044b5afe.png
http://puu.sh/gPfNm/9e63769f7d.png
Every other usb device I have/try works. I tested all my usb 2.0 and usb 3.0 ports and they all work with my mouse, keyboard, and flash drive.
I'm not really sure where to go from here. I contacted Ubisoft (maker of the game Rocksmith) and they said it was a driver issue and I haven't received any more help. I'd really rather not need to dual boot win 7 and win 8.1 just to use the cable.Paul
Given what the cable does and what device manager looks like it is a driver issue. Their driver. Your best bet is to contact the developer BUT I do wonder if you have tried re-installing the driver in compatibility mode for win 7
To install in compatibility mode do the following:
Right click the installer>properties>compatibility>choose OS
http://windows.microsoft.com/en-US/windows-vista/Make-older-programs-run-in-this-version-of-Windows?SignedIn=1
(works in vista, win 7, win 8, and win 10)
Wanikiya and Dyami--Team Zigzag -
After upgrade to ios 6 usb connection problems with car stereo
Hi Everyone,
after ios upgrade to ios6 i am not further able to use the iPhone 4s as music device - having usb connection problems ("not readable"). I am sure, that the upgrade ist the culprit; worked fine before. My car stereo is built in a Volvo XC 60; the device is connected via the standard usb cable by apple.
Any Ideas?
Thanks
Ivo(same problem thread): see also https://discussions.apple.com/message/20185146#20185146 (not fixed)
-
Hello all,
I tried to charge my N85 with an [non-Nokia] USB battery charger (Lenovo 90W Slim AC/DC Combo Adapter) via the Nokia Connectivity Cable (CA-101) to keep down the amount of chargers I have to carry.
But except of asking, which data connection profile I want to use, there is no charging at all.
Am I doing something wrong or is the N85 only chargeable by the original Nokia wall charger?
Thank you
sicut30-Nov-2008 09:35 PM
rbreton74 wrote:
@sapporaby: Are you sure you have read my post completely? "Apple" is a brand o usb charger that does not work with my Nokia N85. It's a brand like "Kensington", with a usb charger that do work. Both usb charger worked with my old Nokia N95. I just want to know whether someone else has this problem usb charging problems too or if only my problem, and to make know @sicut that he is not the only one with usb charging problems with his Nokia N85 and his Lenovo charger.
@sapporaby, is it "apple" a word taboo for you? Why "kensington" is not taboo? Why "lenovo" is not taboo either?
1. I have had every Mac made since 2003.
2. I am typing this on a Mac now.
3. I have had and still have every iPhone made.
4. Same with every brand iPod.
5. I am running Apple software right now and the Nokia for Mac software.
Is that taboo enough for you? DON'T ASSUME because now your taboo question is moot.
As for your the Apple charger does not work issue, my question still stands. While your Apple charger may have worked with your N95 there is no reason why it should work with your N85. Are they the same phone?. Is the N85 made by Apple? No again. Does the Apple charger supply the same charging voltage as the Nokia charger that came with the phone? These are issues that come into play. What is so hard to use the cable that came with the phone. It seems, and maybe I am wrong but you and the OP are making a mountain out of a moe-hill.
Just use the cable that came with the phone, in the USB port of your computer and be done with it. I am having a very hard time trying to understand what the problem is with using the cable.
Message Edited by sapporobaby on 30-Nov-2008 10:07 PM
Show the KUDOS button some love.... Hit that bad boy.... It don't hurt....
Apple iPhone 5,
Retina MacBook Pro, iPad Mini, Nikon D4 -
HT4106 connecting cable usb B (master Keyboard) to Ipad 2
Hi,
I'm a professional musician, and i use an M-Audio Kestation 49 on my Ipad.
For the moment i use an usb B/A to connect to the camera usb adaptator. It works fine (after some minutes it tells material unsupported, i clic OK, and it works for hours...
The problem is when i put my Ipad 2 on the K&M stand (to put on a mike stand, a must have!!).
The camera adaptator is too big, and i can't connect it totally on the ipad...
So my question is:
Does someone knows where i can find a cable usb B/ 30 pins to connect my keyboard directly to the ipad, it should be smaller then the camera adaptator, and fit even when the ipad 2 is on its stand...
Thanks for the help.
Regards.You mean "NO", i don't know if it exists? or "NO", there's no way to have this sort of cable...?
I've seen some Line 6 Keyboards connected on Ipad.
My Keystation works fine on it too, but the camera adaptator is not very pratical for connecting a simple usb cable. Too big.
Regards -
Xilinx Platform Cable USB II Status Light Always Off
I have been using the Xilinx Platform Cable USB II with ISE WebPACK 10.1 on Windows XP for a couple of years now.
Last week I bought a second Xilinx Platform cable, but I have not been able to get it to work. I have followed the instructions in the installation guide (ug344), and the Windows Found New Hardware Wizard runs twice when the cable is plugged in to a USB port, as expected. The wizard indicates that the installation of the firmware loader and the cable are successful. However, the status light on the cable never turns on. Also, the Cable Auto Connect operation in iMPACT fails:
Welcome to iMPACT
iMPACT Version: 10.1.03
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
LPT base address = 0378h.
ECP base address = FFFFFFFFh.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xp2.sys found.
Driver version: src=2301, dest=2301.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable PID = 0008.
Max current requested during enumeration is 300 mA.
Type = 0x0005.
write (count, cmdBuffer, dataBuffer) failed C0000004.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 2301.
File version of C:/Xilinx/10.1/ISE/data/xusb_xp2.hex = 2401.
Firmware hex file version = 2401.
Downloading C:/Xilinx/10.1/ISE/data/xusb_xp2.hex.
Downloaded firmware version = 2401.
Done pin is low. Cable will be updated.
Done pin is low. Current retry count = 0.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 1.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 2.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 3.
Error updating cable firmware.
I have tried using the cable with the latest version of ISE WepPACK on a computer running Windows 7, and I have followed instructions to uninstall and reinstall the cable drivers using a DOS command prompt. The cable behaves as described above.
Is there anything else I can try, or is the state of the status light an indication that there is hardware problem?
Thanks.Correct. Even though iMPACT reports it is attempting to install firmware, the light is never on. I have not seen it on in any color since I bought the cable.
I have tried the latest version. I have a newer machine running Windows 7 with ISE WebPACK 14.7. Again, the drivers seem to install witouth a problem, but the light remains off. Here is the log when I attempt to connect to the cable:
Welcome to iMPACT
iMPACT Version: 14.7
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
AutoDetecting cable. Please wait.
*** WARNING ***: When port is set to auto detect mode, cable speed is set to default 6 MHz regardless of explicit arguments supplied for setting the baud rates
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusbdfwu.sys found.
Driver version: src=1027, dest=1027.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable PID = 0008.
Max current requested during enumeration is 300 mA.
Type = 0x0005.
write (count, cmdBuffer, dataBuffer) failed C0000004.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
write cmdbuffer failed 20000015.
Error reading reference voltage level.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 4 sec.
Cable autodetection failed.
Thanks.
-
It recognized the new iPod as "Unknown Device" in Device Manager... I went through all the steps I found in the Apple support network - and to no avail...
There's always that unrecognized yellow exclamation point on the question mark icon, even though the iPod is charging fine... What to do?
Thank you in advance
Ran BleichI have exactly the same problem, my 4g 20 gb Ipod will report a fully charged battery when I connect it to the Apple USB AC adapter (or any other AC USB power adapter), connecting it to my Laptop USB 2.0 port gives the same indication, however, the battery is not really charged, upon disconnecting the cable from the AC adapter or the USB port, the battery icon reverts to its former status (almost completely discharged). The only way I can charge this Ipod is to connect it to a powered Firewire port or dock the Ipod in my Altec Lansing InMotion speakers, I know the USB AC charger used to work before I updated Ipod with the latest updater, I did the update just after it became available, I am not sure if this problem was caused by the update or not, I don't usually have to use the USB ac adapter, so I can't tell if the usb charging problem appeared right after the update or much later.
It would be much appreciated if somebody posts a solution for this...
IBM Thinkpad T42 Windows XP
IBM Thinkpad T42 Windows XP -
Platform Cable USB II Stopped Working
Hi all,
I have successfully been using the Platform Cable USB II to program a Spartan 6 for around 6 month. Today I tried to load a new program and I could not connect to the cable. See below for the message iMPACT gives me. When I came in to use ISE and iMPACT today ISE said my license was no longer valid; I pointed ISE to the license file I had always been using (located in C:\Xilinx) and ISE stopped complaining. AS far as know nothing else in my system has changed since the last time I programmed the Spartan 6. The Platform cable light is green and Windows recognizes the cable just fine. I am using Windows 7 and ISE 13.4 (nt64). I have checked other posts and it seems this is not a new issue, but I was unable to fix the problem by following any of those suggestions. Please help! Thanks,
Aaron
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_emb.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Invalid device driver license.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 32 sec.
Cable autodetection failed.
WARNING:iMPACT:923 - Can not find cable, check cable setup !Thanks for the help. Very useful! I've done the uninstall -> install again. Unfortunately, it doesn't solve my problem. Cable is plugged in. Green light is on. Jungo windows driver appears in devices. But still error code 923. Grrr. Annoying!
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xp2.sys found.
Driver version: src=2301, dest=2301.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Invalid device driver license.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 2 sec.
Cable autodetection failed.
WARNING:iMPACT:923 - Can not find cable, check cable setup !
-
Nokia N900 USB connection Problem
Hi,
Nokia N900 USB connection Problem.
I am very embarrassed to admit this but.......
I removed something (I cannot remember what) and now when I connect my Nokia N900 to my pc using the data cable it starts charging only.
Previously I could choose between "mass storage" mode and "PC Suite" mode.
Now I cannot access any files on my phone from my PC.
can anyone help please?
Thank you in advance.Problem Solved!!
I had unckecked USB status menu in the powatool app. -
I'm having a problem with my Bose USB sound system that has just recently developed. The system is plugged directly into the back of my Mac Pro desktop so it's not going through any hubs or secondary systems. When I first start my computer the sound works just fine. But after about 10 to 15 minutes of use the sound stops completely - as if the sounds have been turned off. If I boot into Windows 7 using Boot Camp, the sound system there works just fine with no problems at all, so I do not believe this issue is hardware related but is something associated with OS X.
This all started recently after installing Tinker Tool and then realizing that their latest version is not compatible with Snow Leopard. I followed their directions and told Tinker Tool to restore the previous settings and then I removed it from my system. Now, I'm having this USB sound problem. I think it's highly probable to be the cause of my problem.
Is there anyway to reinstall the USB drivers in OS X without reinstalling the entire OS? Or, is there something else I can try to restore the USB function to Snow Leopard? Many thanks for any tips or suggestions.They are plug and play.
I did try unplugging all of the USB devices and then powered off the computer and unplugged it for about 5 minutes as I heard that that sometimes solves USB problems. However, upon reconnecting the problem returned. All other USB devices seem to be working normally - it's only the Bose sound system. I tried plugging it into a different USB port in the back of the computer but the problem continued after about 10 minutes. Therefore, I am convinced this is not hardware related.
At this point I am thinking I need to reinstall OS X Snow Leopard to undo whatever Tinker Tool damaged. Is it possible to just replace the USB drivers in OS X without reinstalling everything? -
Restaure mi ipod touch 4g porque solo sale el icono de itunes y un cable usb en pantalla ?
Restaure mi ipod touch 4g porque solo sale el icono de itunes y un cable usb en pantalla ?
Demonios! A mi me acaba de pasar lo mismo y no puedo hacer nada...!
Help!
Maybe you are looking for
-
How can I transfer elements from an old document to a new one?
Hi everybody, I'm quite new to InDesign and not really from this area, so I'm having a tough time learning how to use it. My first project is what I first thought would be simple for a start: a recipe book. So I started using different master pages f
-
The hard drive in my old computer was fried basically and there is no way to get onto it again. I had adoe creative suite 5.5 and dreamweaver 12 on it but i am not sure how to install either of these onto my new computer now. Is there any other way t
-
IWeb crashes when saving (Mountain Lion)
Hi, I installed Mountain Lion on a free partition of my iMacs (8.1) harddrive, then migrated all the data from my timemachine-backup I saved with Lion on the same machine. Everythings seems to work well, except iWeb: Whenever I try to save my website
-
Hi ABAP developers, Where can I get Inventory Report examples or more information? Thanks in advance, Ol Pom.
-
would you helping me how to use paragorn ntfs? i need to copy my wd external hard drive to my macbook this is my hard drive info: Type : Partition Disk Identifier : disk1s1 Mount Point : /Volumes/....