Cabling & configuring D1000 with two 420R with two dual channel controller

Hi all,
I have a problem for configure a D1000 storage with two Sun Enterprise 420R with on board two dual channel scsi controller for each one.
The D1000 have 4 disks installed, the disks are positioned in the slots 2,3,7,8 and the option swith on rear of D1000 are configured :
5 4 3 2 1
DOWN DOWN DOWN DOWN UP
The Module ID switch are positioned at 0 (I have only one D1000) and the leds of the disks on the D1000 are on.
I have a problem to view all disks from both Sun.
How to I do the cabling the D1000 with the two Sun ? I drew a diagram of my environment to understand how to connect correctly the connectors behind the D1000 and behind the Sun.
http://img152.imageshack.us/img152/4097/schemascsid1000.jpg
Can anyone help me? Any help is appreciated.

are you using HVD scsi controllers? Gotsta doo that with D1000...
if you just want to have each 420R use two drives, then scsi cables on each side and differential terminators in the middle.
if you want to share the drives, you will have to do your homework.
good luck,
haroldkarl

Similar Messages

K8t Neo2 won't run dual channel with Opteron 165

Hi,
I have a K8t Neo 2, and was running a Newcastle 3500+ on it, with 2x1GB PC3200 memory sticks (Buffalo memory) in dual channel mode (ie DIMM 1 and DIMM 3 populated) without any problems. I replaced the 3500+ with a new Opteron 165, and the system would not post. One of the red lights on the D-bracket was red, the rest were out.
To troubleshoot, I removed one of the memory sticks, and the system booted fine. I then put the 2nd memory stick in a non-dual channel setup (DIMM 1 and DIMM 2 populated), and it booted fine. If I try booting the system with the RAM in any dual channel enabled configuration, it will not post. I verified that it isn't a RAM issue, because I have 2 sticks of 512 MB ShikaXRam, which has always worked fine, and I got the same behavior as I got with the Buffalo RAM. I have tried changing the RAM clocking in the BIOS, and that also doesn't help, because it seems it reads the speed automatically no matter what you set the DRAM clocking page to.
Does anyone have any suggestions? Is this board not Opteron 165 compatible with dual channel memory?

Alright, I tried all of the steps mentioned, setting optimized defaults, even tried changing all memory timings to the most conservative available. The only way the system will boot with 2 DIMMs installed is if they are in the two slots furthest from the CPU. It will also post with 3 DIMMs installed in any configuration.
I also have a generic 500 w PSU that is rated 32a on the 12v rail that I tried quickly plugging in (just plugged the 2 PSU connectors to the motherboard without hooking any of the IDE devices to it) It still exhibits the same behaviour. With no hard drives, optical drives, etc plugged in, wouldn't that pretty much eliminate the PSU as an issue?
I don't want to just spend $100 on a new PSU if it's highly unlikely to be the issue. Does this sound like something I'd need to replace the motherboard to fix? Is the performance difference between dual channel and single channel enough to even warrant buying a new board? The reason I want to avoid replacing the board right now is because I still have an AGP card, and don't want to replace it right now as well as the board, and getting another AGP based board seems to be stupid. Also, AGP boards are really hard to find now, and most of them available locally run on the ULi chipset

I am trying to connect a 24" cinema display with mini display port cable to a 24" imac with a displayport - is there a cable for this as these two connections are two different sizes

I am trying to connect a 24" cinema display with mini display port cable to a 24" imac with a displayport - is there a cable for this as these two connections are two different sizes

Hi Gilly,
I have no proof, but I think it will not work with an adapter, only Mini Display Port or Thunderbolt.

Can connect two Macs with USB2 cable?

Can connect two Macs with USB2 cable?

You can connect two Macs with an ethernet wire, or conect two Macs using Firewire if one is placed in target disk mode, but that is it.

Can I run two displays with my Macbook Pro?

I have the early 2011 Macbook Pro, with the 256mb ram on the graphics card, and what I think was the first generation "Thunderbolt" video output. I'm currently running a single 27"Cinema Display using a mini-display port adaptor out. I'm wondering if there's a way to drive two monitors with it - say a Thunderbolt display and the current Cinema Display? What configuration of displays, adaptors, and/or cables would I need to do this?
Thanks!

I suggest reviewing information here:
http://support.apple.com/kb/HT5219?viewlocale=en_US&locale=en_US
in the sections:
"Using the Apple Thunderbolt Display" and
"Using Mini DisplayPort displays or displays connecting with Mini DisplayPort adapters on Macs with Thunderbolt Ports:"

How do we sync contacts and calendars (ONLY) between two iCloud accounts, two iPhones and one iMac with two user accounts?

This is complex. Until today we had one iMac with two user accounts - one for me and the other for my wife. We sync'd our calendars and contacts between our two user accounts using my iCloud account, thereby keeping our schedules coordinated and our contacts information always the same between us. Also, as I had an iPhone, I sync'd my phone with my iCloud account, thereby keeping the contacts and calendars in the two user accounts on the iMac AND my iPhone sync'd. (I also sync'd other things, like Notes and Mail and Safari settings, between my iPhone and my user account on the iMac, but my wife did not want to be burdened with all my emails showing up in her email account and I wasn't interested in hers, etc., so we didn't sync anything between us other than calendars and contacts.)
We've finally bought my wife an iPhone and set up an iCloud account for her. And of course she now wants to sync several items from HER account on our iMac to HER iPhone, but I don't want them, just as she doesn't want all of my other stuff. But we still want our mutual calendars and contacts to sync to HER new iPhone, just like they already do to mine. But I can't figure out how to CHANGE her iMac user account from using MY iCloud account on the iMac to using HER new iCloud account, and then having HER iCloud account speak to MY iCloud account but share JUST our calendars and contacts.
Originally I tried a workaround by simply having her iPhone log into my iCloud account. That works great for the calendars and the contacts. But...she can't sync anything else from her iMac account to her new iPhone because she's presently "forced" to use my iCloud account. And neither of us want to sync our other things to each other's iMac accounts or iPhones. Also as we're both using my iCloud account, in things like the Find My iPhone app, the Cloud is seeking two phones labeled with my name and none with her's. So we definitely don't want this as the set-up and communications network between our devices.
We want to set up our users on the iMac to sync to our SEPARATE AND DIFFERENT iCloud accounts and then have those iCloud accounts sync calendars and contacts (ONLY) between themselves, and then push that data to our separate iPhones (or the other way, from either of our iPhones to the individual accounts on our iMac and the other person's iPhone). Does this description make sense to you? I've diagramed it nicely using Keynote, but even thiough I can draw it, I can't figure out how to set up and configure all the devices to make it work. If you would like me to send the Keynote slides (just two of them - the current and desired configurations - please send your email address to me at [email protected] and I'll be happy to forward it to you.
If anyone can help me set this up I'd be most appreciative! Thanks so much. Merry Christmas and Happy New Year to all readers in this community!

BobT.
I had the same problem, and decided to look into it last night.
First of all, the solution I would like to have is for Apple to allow for selection of iCloud accounts per application, i.e. Contacts to one, Photo Stream to another. I believe this would be the most straight forward solution for the problem we are facing.
Since this is not an option I came up with a workaround. I was most interested in solving this for Contacts, so this is what I tested for. Now I have all 3 devices with the same contacts.
1) Turn off iCloud for Contacts on all devices. On the device that has the Contacts list that you would like to propagate to all others select to keep the contacts, and on the others select not to keep them.
Note that the current backups still exist on iCloud, so in case something goes wrong you can still turn the iCloud for Contacts back on to get your current Contacts back.
2) In iTunes, sync All Contacts with the phones, starting with the one with the Contacts content you chose to keep.
From this point on, the 3 devices should sync contacts with each other.
This, of course, will stop your iCloud backups of Contacts, but I don't think this is really needed. You are already storing copies of your Conacts on 3 devices, which for good parts of the day are likely not all co-located. You also potentially have Time Machine backups turned on, which would mean there is a 4th copy there as well. For the case of Contacts iCloud only complicates matter ... that is until Apple implements the solution I first wrote about.

Can i set up my iPad and iPod to use iMessage between the two devices with the same Apple ID?

Can i set up my iPad and iPod to use iMessage between the two devices with the same Apple ID? SO i could iMessage if out from my iPod to my iPad at home to be viewed by a family member?

Look into using Apple Configurator. It's the easiest way to "reimage" and Manage iPads that I know of right now.
http://itunes.apple.com/us/app/apple-configurator/id434433123?mt=12
Also, look into using the Educational Volume Purchase Program, if you have not already done so.
http://www.apple.com/education/volume-purchase-program/

Two subnets with different mask on a single router?

router 1941
Hello. I'm needing assistance with the setup of two subnets within a single router.
Here's my information:
Router has only two GigabitEthernet interfaces.
GigabitEthernet0/0 has 172.20.0.1 ip and 255.255.252.0 mask.
GigabitEthernet0/1 has 172.21.0.1 ip and 255.255.128.0 mask
Now, on each side there is a Switch with two computers.
I need to have 1 computer on each side on the same subnet, and the other one on a different subnet, meaning a pc on the same side cannot communicate with the other computer on its side, but can with another computer on the other side.
I have no idea how to configure this on the router, can anyone please help me?
Thanks in advance!

>>> So you want PC1 and PC3 to be able to talk to each other but you don't want them to be able to >>>talk to PC2 and PC4 and vice versa.
This is correct.
>>>If so you don't need a router, you can just a switch (or switches) and use two vlans with no L3 >>>interfaces.
Unfortunately they are not giving me the choice of making my own net design. I need to setup this with all the devices mentioned (1 router, 2 switches, 4 pcs).
>>>If so you don't need a router, you can just a switch (or switches) and use two vlans with no L3 >>>interfaces.
As long as they communicate with the appropiate PC, it doesnt matter if they communicate to other devices or not.
Thanks again!

Can I have two LANs with the same IP route to each other

Hi there,
I have a customer who has a televantage voip network on a private 192.68.0.0/24 network but has two sites connected via a wireless tower that wants to enable QOS over between the two sites by using a 2621XM router at each end. I've enabled QOS on both routers for voice and video but haven't deployed this yet since I'm not sure if I need to change one of the sites networks to a different network number since I'll have the routes in place with a 192.168.1.0 on the WAN side. If both remote networks stay with the same number scheme of 192.168.0.0/24 will they be able to find each other when requesting where a remote 192.168.0.0 host is or do I need to change of the offices networks to a 192.168.2.0 network to make this work? Sounds kind of basic but before deploying I wanted to get some input...thanks.

Routers cannot route unless the address blocks for each interface are different.
If you have two sites connected by any kind of link, and you'll use one site as a gateay to the Internet, then you'll need at least four different addresses/ blocks:
The 'b' site LAN, i.e., fa/0/0:192.168.0.0/24
The 'b' site WAN (interconnecting link), i.e., fa0/1: 192.168.1.1/30
The 'a' site WAN (interconnecting link), i.e., fa0/1:192.168.1.2/30
The 'a' side LAN, i.e., fa0/0:192.168.2.0/24
(assumes that your wireless link is acting as a bridge or non-routing link) - the fa0/1 device connects to the wireless devices).
If you use the same router on the 'a' side for the interconnecting link for both the 'a' LAN and the Internet gateway, then the third interface would be your Internet WAN address.
The 'b' side LAN interface is your 'b' side default gateway for you clients
The 'a' side LAN interface is the 'a' side default gateway for your clients
Set a default gateway on the 'a' router to the ISPs Default gateway / next hop address.
If you're using a third router for an Internet gateway, then the LAN interface address becomes the default gateway for the clients on that LAN, and you'll need to set up a static route pointing to the other LAN in the routers that connect the two LANs..
A routing protocol may be useful but, depending on your actual bandwidth available, it's probably better to just set up static routes (no routing protocol bandwidth utilization).
The /30 for the WAN link gives some economy of address usage, but it may also secure the link better, since there are no additional addresses for the intruder to use; they'd have to spoof one of the two valid addresses (.1 & .2) as well as crack your encryption (and / or other security).
There's an armload of other possible configurations / topologies / address schemes, I believe this one would be reasonably common.
The bottom line is that a router can only route from one address block to another. In order to pass traffic between two segments with the same address block, you need a bridge / switch, or some other layer one/two device (like a wireless transceiver pair).
Good Luck
Scott

Payment terms in OBB8 with 50 days with two day of payment.

Hi Experts,
We need some helpu2026. We have to create a payment terms in OBB8 with 50 days with two day of payment, day 05 and 20.
Requisites:
If the bill expire date is between the days 01 and 15 from month X, the pay is realized the day 05 from month X.
If the bill expire date is between the days 16 and 31 from month X, the pay is realized the day 20 from month X.
Any idea
Best Regards,
Driss,

Hello Driss
In the payment terms , where you define cash discounts .
You can configure the requirement you specified .
Maintain as follows :
Term ,    Percentage     ,        No.of days      ,     Fixed date   ,   Additional month
1         ,       0.00%            ,        15              ,            05           ,           0
2         ,       0.00%            ,       31                 ,         20             ,         0
I think this should work fine
Let me know if this is ok
Ravindra Kumar

Append two files with added time stamp

Hi experts,'
MY Requirement is I need to pick two files from two different FTP Locations and append them to file receiver FTP Location with Added timestamp.
How to achive this as with append we do not get option of adding time stamp.
Other thing is I want all the appended files should be there in Receiver folder means like if we get two files today they should be appended to one and shld be put in Receiver folder then two files for tomorrow and they shoud be appended as a separate file in Receiver Folder.
How to achive this??
Regards,
Nidhi

Hi Nidhi,
>>MY Requirement is I need to pick two files from two different FTP Locations and append them to file receiver FTP Location with Added timestamp
Use BPM and pick the two files
>>Other thing is I want all the appended files should be there in Receiver folder means like if we get two files today they should be appended to one and shld be put in Receiver folder then two files for tomorrow and they should be appended as a separate file in Receiver Folder.
Use variable substitution and create the directory and filename dynamically...
Use Dynamic configuration module in receiver adapter and do as specified in this blog:
/people/madanmohan.agrawal/blog/2009/05/20/combining-three-different-aspects-of-pi-asma-af-module-and-variable-substitution-in-one-shot
Regards
Suraj

Two problems with the newly implemented WF in UWL

Hi all:
       Finally I could see WF of leave request in UWL , but there seems to be two problems with it.
       The first is workitems disappear very slowly, for example , when approve it, the workitem would disappear at once at backend, however, workitems would disppear in five minutes.
       the second is for example employee A submits 5 five applications (just for example ), as click one workitem, five applications would appear the application list .
      could you please kindly give some suggestoins ?

Hi,
reduce "Default Cache Validity" value to 1 from Universal Worklist Service Configuration link under System Administration -> System Configuration -> Universal Worklist.
you can configure deltapullmechanism also.
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/eb/101fa0a53244deb955f6f91929e400/frameset.htm
Regards,
Koti Reddy

Two problems with custom kernel

I get two problems with my custom kernel that is not using initrd and otherwise working fine:
1) initscripts does not print anything, i.e., I see the kernel messages and after a short while the login prompt. It seems to start the daemons, however, since my network is working. During shutdown the printout is working as usual.
2) the machine does not power off properly (just hangs/stops after saying that is now powers off).
I am missing some kernel options? Or do I have to configure something differently for not having an initrd?
Thanks, CC

ccom wrote:I now re-compiled with Arch Linux's default settings (except for SCSI, SATA, and filesystem drivers built in) and noinitrd in GRUB. I get the same two problems. What is initrd doing that I missed?
how about display drivers? are you compiling them in the kernel or as external modules?

What happen when we connect Two PC with IP from Same subnets

Scenario 2nd : What happen when we connect Two PC with IP from Same subnets. PC1 -192.168.10.1/24 PC2 - 192.168.10.2 on a two different L2 Switch on different vlans which are connected via a LAN cable.
All ports are access ports
Interview Question : No More Info.
Pc1<SwA>------<SwB>PC2
Q.1 Will they communicate If yes what will be packet/frame flow.
Q.2 If not where will be the packet/frame drop. ? Why.
I need step by step if possible plz how the packet moves , vlan taggings n all internal works that happens behind .. plz
thnx in advnce ....

Hi Abhishesk,
The PCs should communicate each othet.
Since there is no trunk port involved, there is not tagging involved.
Since both the PCs are into the same subnet. PC1 will not need default gateway for the communication with PC2. So PC1 will start with sending ARP request for PC2 MAC address.
Since all the ports in SW1 are in same VLAN, the ARP should reach all ports including the switchport where SW2 is connected to.
Sw2 has got a complete different access port on ALL the switchports. Sw2 will receive the ARP from Sw1. Remember that there is no tagging for the frame. Hence Sw2 will again send the ARP packet to all the ports which belong to same VLAN wherein the packet is received. ie, Sw2 will send the ARP packet to all the ports in Sw2. PC2 will also get the the ARP.
The ARP reply will make it way back using the same logic.
Now both the PCs can start the actual packet exchange.

Installing oracle10g on two servers with same databae

Dear DBAs
I have two servers and one SCSI SATA box as storage device which i have configured in RAID5 format. Servers are connected to channel 0 and 1 of the SATA box respectively.My OS is RHEL ES-4
I want to install Oracle10g on these two machines with SATA box as the Databse Storage medium. I donot want to use RAC as my clients donot have DBA. The servers has to be configured in a failsafe method.

hi gert
the SATA SCSI box is LSI Logic Megaraid sas 8408E. My aim is to have a backup server which needs to be switched on once the main server fails. I can afford for a little bit data loss. Only thing is the backup server should use the data files of the crashed server.

Cabling & configuring D1000 with two 420R with two dual channel controller

Similar Messages

Maybe you are looking for