Cabling problem? - all status LEDs flash - Link/Act, Full/Col and "100"

I have a CAT5 cable installed in my house. When I connected it to my WRT54G router and computer I have on the router all three of the Link/Act, Full/Col and 100 LEDs flash in sync. My PC tells me the LAN cable is not connected. I have reterminated the cable and still get the same dispaly on the router and message on my PC. The manual is silent on this. Can anyone help? The router's firmware is V1.02.0 and the router works fine with other cables connected to the other ports. I have tried all the ports with the cable in question. Thank you.
Message Edited by snowrider on 07-21-2006 11:58 AM
Message Edited by snowrider on 07-21-2006 11:59 AM
Message Edited by snowrider on 07-21-2006 12:02 PM

Hello,
solved the problem by my self. One statement was missing. IT was reverse-route, which is requiered to create the routing entries.
crypto dynamic-map CRYPTO_ISAKMP_CLIENT 1
set transform-set VPN-TRANSFORMSET
reverse-route

Similar Messages

Please can you help me to solve my problem ( I have iphone is linked with Apple ID and I forgot that Apple ID and I can't remember it , I need thats Apple ID to activate my iphone ,,, what should I do ?

please can you help me to solve my problem ( I have iphone is linked with Apple ID and I forgot that Apple ID and I can't remember it , I need thats Apple ID to activate my iphone ,,, what should I do ?

mohammed aljasim wrote:
there are many people that error is happened with them and one of this people is me ,, Apple must be find the solution for this problem
You are absolutely WRONG. Apple bears no responsibility in this at all. YOU purchased a STOLEN phone. You are guilty of receiving stolen property at best. Take it back to wherever you bought it and demand a refund. Failing that, turn it over to the police. You got ripped off. I'm sorry you wasted your money, but there is NOTHING Apple or anyone else can do for you. Only the rightful owner of the phone can unlock it.

CFP 2110 - Status led flashing continously

I'm running into problem with a cFP 2110.
During the debugging of my RT application on the cFP, I get an error message "Host IP address not in the access list". At this time, I was unable to download any application to the cFP. the VI server IP access list was configured with *. So all the IP address can access to the cFP.
I found a procedure on the ni web site to reset the system.
-Set to safe mode
-ftp the cFP and delete all the file
-Remove the safe mode.
It means that there is no more OS or LabVIEW RT on the system.
Now, When I restart the cFP, the Status led is flashing continously (1 flash / 1.5s) and I don't have access anymore to the cFP in MAX.. Can some one help me on this case ? .
Thanks
Attachments:
Ni_recommendations.pdf ‏126 KB

Hi Poussin,
I would recommend flipping the Reset IP dip switch (dip switch 7). This
should get the controller to show up in Measurement and Automation
Explorer(MAX) as 0.0.0.0. If you can't see the controller, you may want
to try turning off your firewall. Often computer firewalls will prevent
customers from seeing unconfigured controllers in MAX.
Once you find your controller, you can flip the reset IP dip switch back to the
off position and reset the IP address. For more information on this,
click on your FieldPoint controller in MAX that will be displayed as
0.0.0.0. In the MAX help that appears on the right, click on the link
titled, "Configure Network Settings." If you need assistance
choosing an IP address, please look at this KnowledgeBase.
Once you have assigned an IP address to the controller, the status light should
stop blinking once. You will then need to install software.
Here is a general
document that describes how to assign an IP address and install software.
Please let me know if you have any other questions.
Regards,
Ching P.
DAQ and Academic Hardware R&D
National Instruments

CompactRIO unusual error status LED flashing continuously

Hi,
I have a cRIO 9014 controller with an error i can't solve.
After re-installing LV 8.5 on my laptop MAX could see the controller but with the VISA and NI-RIO error. I wanted to obtain the IP address from the DHCP server (before i used the static IP address without any problems), rebooted the controller and the status LED started flashing continuously every 1 second. (unrecoverable error or corrupted flash memory card)
I rebooted the controller several times with IP reset but LED is still flashing. Also in MAX i can't see the controller anymore so reformatting controller is not possible.
Firewall is off, crossover cable is connected, IP of host is ok but no cRIO in MAX
Found a similar problem on the forum http://forums.ni.com/ni/board/message?board.id=170&message.id=238333&query.id=24781#M238333 but it didn't solve my problem unfortunately.
Thanks for your help!
Greetings from the Netherlands

Hello TrabW,
Thank you for your post on our webforum.
Can you try to start up the controller in safe mode? Is it possible to ping the controller? Please try the default IP address and the one you entered (in case the controller didn't reset the IP). Please let me know the results,
Best regards,
Martijn S
Applications Engineer
NI Netherlands

Status LED Flashes 5 times?

There are only nine terminal bases in the back and no terminal bases were added to the bank while the power was supplied. Is there any other reason for this error? Any help would be greatly appreciated.

The status light flashing 5 times means different things for different network modules. Without knowing which network module you are using, I can not provide specific information.
It is most commonly seen with the FP-1000/1001 Serial Network modules when an I/O module is unrecognizable. This can happen in the following circumstances:
1) A module that may have been connected previously was not available when Find Devices! was issued.
2) The firmware of the network module may not be updated to support the I/O module. For the latest driver version of a FP-1000/1001, the link is:
ftp://ftp.ni.com/support/fieldpoint/Update/FPupdate.zip
3) There may be 10 bases on a bus but the system only supports up to 9.
4) There may be a bent pin at the point where the module connect
s to the base.
5) The terminal bases were connected or disconnected with power applied resulting in a bus failure condition.
Regards,
Aaron

Open link in full Reader and not web browser

Hi
I am currently design an internal help page with PDF forms - Is there anyway to open a pdf web page link in Internet explorer and open the PDF in the full Adobe x reader and not the internet browser version?
Thanks in advance
Andy

Hi
If possible yes I'd like to specify in the form for it to open in the full reader.
Regards
Andy

Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
blackberry 8100 v4.2.1.96

Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
So if you're willing to try that, do the following.
First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
http://www.blackberry.com/btsc/KB03485
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

WRT54G Router - All lights continuously flashing?

This morning my WRT54G's lights (link/act, Full/col, 100) were continuously flashing on and off simultaneously and I'd lost all network connectivity. I've not made any changes (firmware) to the router for about 1 year, and it's been working fine. I've pulled the plug on the router and when the power's back on, the lights go out but still no connectivity.. after a while all the lights start flashing. I'm just wondering if I need to buy a new one
Laurent

Quite right! The old adapter says the output is 5v and I do have another lying around.. my router is up and running thanks for the tip.
Laurent

FP-1600 Status LED blinks 17 times.

My FieldPoint bank has 9 modules. I previously had a problem with the FP-TB-10 power and ready lights blinking, but that was because one of my dual-channel modules was not seated correctly. Now the status LED is blinking 17 times. The manual says to contact NI about this. The FieldPoint Explorer seems to find all of the modules correctly, though. Anyone know what's up?

Aaron,
I checked the firmware and the FieldPoint Explorer version, and I'm using 3.20 and 3.0, respectively. When I power cycle the FP-1600, the 17 blinks of the status LED go away. Communication works, and all of the devices are found. However, communication does drop out from time to time, and eventually the status LED begins blinking 17 times again.
A possibly related issue is that the FP-AI-V10 dual-channel module that I have plugged into slot 2 of the FP-TB-10 base causes the FP-TB-10 to flash its power and ready LEDs. Re-seating the FP-AI-V10 seems to fix this, although the module is definitely already clicked into place when I see this problem. Upon reseating (or just pressing on it without removing the module), the FieldPoint Explo
rer program finds this module.
I'm tempted to think that this issue with the FP-TB-10 and FP-AI-V10 are unrelated to the FP-1600's status LED blinking 17 times because even with the FP-TB-10 removed from the bank, I still get the flashing LED.
Any ideas? Also, what is a GPF type error?
Thanks,
Jake

CRIO status led 2

I have two cRIO-9014 that are exhibiting the same problem... the status led flashes twice every three seconds. According to the documentation this indicates that "The controller has detected and error in its software". I can configure the cRIO from MAX but can not connect to the device from the LabVIEW develoment environement. I've tried formating the cRIO, setting up the IP addrs etc and reinstalling the software with no success. Another thing I've noticed while interrogating the cRIO using MAX is that there is a VISA Error and a NI-RIO Error present under Devices and Infaces. Is there a solution to restore my cRIO's to their original state or would I have to send it back to NI to be repaired?
Regards,
Rob

What Rev of 9014 Controller do you have? The later rev's require NI-RIO 2.4.1 due to a change in the Disk on Chip memory. Check out the following Knowledgbase:
National Instruments cRIO-9014 Disk On Chip Change Notification
Regards,
Basset Hound

Satellite L50-A-10Q: Win8.1 Pro Wi-Fi status LED is not working

Hello,
I have an Toshiba L50-10-A-10Q Notebook running BIOS Version 1.30 and EC Version 1.10.
I recently updated from Windows 8 to Windows 8.1 Pro.
I followed the update instructions found on the Driver Download page.
All function keys and modules (Wifi, Bluetooth, etc.) work fine.
However, the status LEDs do not work properly.
The status LED for Wifi is always off, even when Wifi is activated and connected.
The status LED for the Touch Pad is also always off, even when it is deactivated.
Power LED and charge indicator work fine.
All status LED were working properly before the update to WIN 8.1.
Is there a solution for this problem?
Kind Regards
Niko

Why you dont try to update or reinstall the Intel WLan driver and Toshiba System Driver again?
Since this procedure helped to solve the touchpad issue and I guess this would solve problem with the WLan indicator too.
[Intel Wireless Lan Driver 16.0.2.1.0.s64 for Windows 8.1 - 64 Bit|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=2&selSeries=178&selProduct=7948&selSh ortMod=3983&language=13&selOS=46&selType=all&yearu pload=&monthupload=&dayupload=&useDate=null&mode=a llMachines&search=&action=search&macId=&country=al l&selectedLanguage=13&type=all&page=2&ID=88542&OSI D=46&driverLanguage=42]

Font rendering problem... (FLash BUG)

Hi all, I have Flash instaled on two machines and both of them are having a problem when rendring flash text.
All text on flash appears like the image bellow. And When I export to SWF the text stays the same.
The font I'm using is Myriad Pro
I'm running Flash on iMac i3 3.06 with 4Gb and 256 Graphics display so that can't be the problem.
Anyone any ideas?
Thanks for the attention.
y

Hi,
i know this problem. It exists since the last os-x update.
Until now there ist no solution - only two workarounds.
a) reinstall osx and update only to an older version
b) sometimes it helps me to close flash, restart flash and publish again.
It seems only OTF Fonts make Problems. I know about problems with MyriadPro and DIN.
There is also a problem creating PDF Files with the OS-X internal "Print as PDF" function.
I hope there will be an update soon....
Stefan

SUPERVISOR WS-X45-SUP7-E REDUNDANCY, STATUS LED ORANGE?!?

hi all,
i have a 4510R+E with 2 SUPERVISOR WS-X45-SUP7-E configured in redundancy mode.
The status leds of 2 supervisor is orange and don't become green!!
Can you help me?
Below you can see the redundancy configuration:
redundancy
mode sso
main-cpu
auto-sync startup-config
Thanks to all!!!
Alberto.

You can see the show module:
FERCAM_4510#sh module
Chassis Type : WS-C4510R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
2    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1908L9HK
3    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1903L5R5
4    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1906L6Z7
5     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1910L326
6     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1910L2SX
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
2 84b8.024b.8a10 to 84b8.024b.8a3f 1.1                               Ok
3 84b8.024b.8e30 to 84b8.024b.8e5f 1.1                               Ok
4 84b8.024b.8a40 to 84b8.024b.8a6f 1.1                               Ok
5 74a2.e680.2dc0 to 74a2.e680.2dc3 3.0 15.0(1r)SG5 03.07.00.E       Ok
6 74a2.e680.2dc4 to 74a2.e680.2dc7 3.0 15.0(1r)SG5 03.07.00.E       Ok
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
5   Active Supervisor   SSO                 Active
6   Standby Supervisor SSO                 Standby hot
System Failures:
Power Supply:   bad/off (see 'show power')

Why won't my led flash after turning it on in accesibility?

Turned on LED Flash for Alerts under accessibility and it worked great for a few days and now it's stopped. What happened? What can I do to get it to blind again when i get calls or notifications?

Never mind. I saw this in the forums after I submitted my question:
"hey everyone. try this before you make trips to the store. turn off the light in your settings and reset your phone. (hold power and home until the apple logo comes up). then when the phone has started back up, turn the light on again and test it ! ( send yourself a text and turn off your screen. you should get the flash when you receive your msg!)
keep in mind though it doesnt flash until you have your screen off.
i think the light must glitch out if you change the flash settings in your camera- and the program requires a restart. hopefully apple fixes this bug (:"
Did this and it worked =)

Is there a link between GL Budget and HR Budget?

Dear All,
Is there a link between GL Budget and HR Budget? is there concept of HR Budget in HR module or it is handle it in GL
If there how I can link it by accounting wise or there is another way to link? Please advice?
Thanks for helping

hi
you can find this in BSEG.
Regards,
Vijay

Cabling problem? - all status LEDs flash - Link/Act, Full/Col and "100"

Similar Messages

Maybe you are looking for