Calendar entries in Active Standby mode
A double question, but both are closely related.
In Active Standby mode it shows upcoming calendar entries for today and future ones.
Q1) Can someone clarfify does it only show 1 entry for future events, since I have placed 2 entries for tomorrow and 1 for the day after. But only 1 (the first) appears in Active Standby.
Q2) I THINK IS A BUG!! It does not show Anniversary as future events in Active Standby. It only appears when it is on the day (bit late if you need to buy a present!).
Any comments
Andrew
Device: N70
Version: V 2.0536.0.2 12-09-05 RM-84
I think this is by design. Not quite sure what the basis is of what is included and what is not. Items from the current day seem to show up in greater numbers than in future days.
All About Symbian - News, reviews and software for S60 phones.
Similar Messages
-
How to tell if Active/active or Active/Standby mode is configured?
Folks:
I am still learning the output of my running config, but how do I tell if my firewall is set to Actve/Active or Active/Standby mode?
In addition, how do I tell if it uses regular or stateful failover mode?
Thank youI wanted to provide this as well, since I found it and it also helped me answering my question.
This output shows Active/Active failover output.
**Note** it says PIX; however, I beleive it will be the same output for ASA.
PIX1(config-subif)#show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: LANFailover Ethernet3 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 4 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Group 1 last failover at: 06:12:45 UTC Apr 16 2007
Group 2 last failover at: 06:12:43 UTC Apr 16 2007
This host: Primary
Group 1 State: Active
Active time: 359610 (sec)
Group 2 State: Standby Ready
Active time: 3165 (sec)
context1 Interface inside (192.168.1.1): Normal
context1 Interface outside (172.16.1.1): Normal
context2 Interface inside (192.168.2.2): Normal
context2 Interface outside (172.16.2.2): Normal
Other host: Secondary
Group 1 State: Standby Ready
Active time: 0 (sec)
Group 2 State: Active
Active time: 3900 (sec)
context1 Interface inside (192.168.1.2): Normal
context1 Interface outside (172.16.1.2): Normal
context2 Interface inside (192.168.2.1): Normal
context2 Interface outside (172.16.2.1): Normal -
Single AIP-SSM in Cisco ASA Failover Active / Standby Mode
Hi,
I can add single AIP-SSM on Cisco ASA in failover active / standby mode?No, both units need the same hardware, that includes the installed modules.
Sent from Cisco Technical Support iPad App -
Stop/start in PGW active/standby mode
Hi all
My VOIP Network has 2 PGW in active/standby mode. But when we add more telco, the state of ss7path is OOS. i must stop/start the PGW and ss7path is IS status.
Now PGW is running services. it processing many call with other telco.
i have question need to support.
When we stop/start PGW,has PGW disconnected all call or not?
Thank for supporting
PhaiLQIf you restart the service on active pgw, calls are disconnected. If you don't want out of services you must pass the control to the standby server first.
From mml console of active server use the command:
rtrv-ne to check the status, the output is:
MGC-01 - Media Gateway Controller 2010-09-07 16:53:42.655 MEST
M RTRV
"Type:MGC"
"Hardware platform:sun4u sparc SUNW,Sun-Fire-V240"
"Vendor:"Cisco Systems, Inc.""
"Location:MGC-01 - Media Gateway Controller"
"Version:"9.6(1)""
"Platform State:ACTIVE"
sw-over::confirm to swich control to standby server
now restart the service
/etc/init.d/CiscoMGC stop
/etc/init.d/CiscoMGC start
P.S. If I remember the right way, the OOS (out of service) state of new ss7 path can be set in IS (in service) via mml command line without service restart.
set- your ss7 path ::IS use tab for help
Regards. -
Asr-group feature in active/standby mode
Hi ,
I would like to know if anyone had used asr-group freature in active/standby mode. Is it not recommended by cisco for active/standby mode ? The feature works in both environment.
Thanks in advance
TomyHi Tomy,
The asr-group feature on the ASA is only supported in Active/Active failover:
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/ha_active_active.html#wp1271955
-Mike -
I have a Nokia E5
I have tried to experiment with the Modes function, whereby you can have one profile for business and another for personal.
The first time I went into Modes (from the control panel), I was asked to go into "Active Standby Mode", which I did. Now everything has changed and I am not sure whether I like it.
Is it possible to get back to how I was before - i.e. before I went into Active Standby Modes ?Hi,
No unfortunately the only way of doing this will be from the app shortcuts. There is to my knowledge no way of doing this automatically. Might be there is an ext. developed app that I do not know of.
BR, PerLs -
6288 - Active Standby Mode menu lost
Hello,
The Active Standby Mode menu has disappear from
Menu-Settings-Standby Mode Settings.
I can't access this setting any more.
My firmware version is 6.10.
Thanks for any advices.
JeromeMessage Edited by hidje on 21-Jul-200707:37 AMI have the same problem. I don't know if I'll use that option but is annoing that I can't activate it. I have software version 6.10 and in display-standby option first submenu is wallpaper (not active standby setting).
Does anyone fixed this BUG? -
ASA Active/Standby mode and Hello messages
Hi Everyone,
On ASA Active/Standby mode i know thatsay inside or any other interface of active and standby ASA should connect to same switch and vlan.
When we assign say ip address to inside interface of both ASA like
ip address 192.168.x.1 255.255.255.0 standby 192.168.x.2 255.255.255.0
Need to know if these inside interface talk to each other or not?
Do they send hello messages?
Thanks
MAheshHi Mahesh,
The ASA Active/Standby Failover pair uses both the dedicated Failover interface and the actual Data interfaces to monitor the "health" of the Failover pair.
The units send Failover hello messages and wait for a reply to determine if the other unit is alive or not.
By default all Physical interfaces are automatically monitored. To my understanding Logical interfaces such as Trunk interfaces are NOT monitored by default. You will have to configure monitoring for each subinterface of the Trunk that you want to be monitored.
You would use the command
monitor-interface
Check the Command Reference section for this
http://www.cisco.com/en/US/docs/security/asa/asa84/command/reference/m.html#wp2123112
I would also suggest reading the following section of the Configuration Guide
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/ha_overview.html#wp1079010
It has information of the Unit and Interface health monitoring of the Failover pair.
If you want to debug Failover activity you could use the command
debug fover
It has multiple additional parameter after that command
Here is the Command Reference section for the debug command
http://www.cisco.com/en/US/docs/security/asa/asa84/command/reference/d1.html#wp2093011
You can even attach a computer on the switch between the ASAs and capture the packets between them an you can see the Failover messages etc from the ASAs
- Jouni -
Step to prep CSC SSM on ASA Active/Standby mode
Hi all,
I am trying to setup Active/Standby HA mode for my site.
Currently the site was installed with one unit ASA firewall with CSC-SSM module, the second unit is the new unit ready to be setup.
My question:
01. My concern is second unit CSC-SSM, what is the proper procedure or step need to prep it?
Is it need to prep the CSC-SSM before the ASA in HA mode Or it will auto propagate the configuration when both unit in HA mode?
What else need to concern? am i need to setup different IP for the CSC-SSM management interface?
Thanks
NoelHello Yong,
Configuration related to the CSC or SSM modules will never get propagated so you will basically need to configure it manually.
Also it's not like if the Config on both modules is different failover will fail but ofcourse you wanna have the same one
IP addresses for each of the modules will be dedicated ones. Remember that failover will fail if one box has the CSC and the other not.
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com -
Does anyone have any idea if I can get the icons on my phone to show at the bottom of the screen instead of the top.
It's not possible without the use of an alternative desktop.
With the built in one your only choices are to have them at the top or not have them at all.
You might want to look at this program as it's an alternative desktop that allows you to change it's layout:
http://www.symbian-freak.com/news/008/02/gdesk_beta_for_s60_3rd_ed.htm -
Nokia 7373 - Adding active standby content not in ...
Hi,
I just bought a Nokia 7373 which I find to be quite cool ! One of the features I like is the ability to display the calendar in the active standby mode. However it only displays calendar appointments, but not todo list entries or any other customizable option.
Is there any way that I can show also the todo list in the active standby mode ?
Cheers,
JoelThere is no way to show also the todo list in the active standby mode.
You could add To-do to the shortcuts (top line in active standby) to get faster access to to-do items. -
Active/Standby And failover link configuration mode
Hi everyone,
When config failover link of ASA in Active Standby mode.
When we config failover int say gi0/1
config t
int gi0/1
failover lan int gi0/1
Need to confirm we do this from interface config mode only or we can do this from global config also ????????
Whe we assign IP to this int we do that from global config mode ????
Regards
Mahesh
Message was edited by: mahesh parmar
Message was edited by: mahesh parmarHi,
Actually the ASA lets you insert a lot of command what ever mode you are under.
In the output you posted is a very important thing to notice
configure mode commands/options:
WORD Specify the interface name
As you can see, the output lists only one option and before that it mentions that this is a "configure mode" command
So even if you entered the command under the interface configuration mode, it would still be entered as a global/configure command mode.
Take the following thing for example
I want to check what configuration options I have with the command "failover"
So I enter the following to my ASA
ASA(config)# failover ?
configure mode commands/options:
interface Configure the IP address to be used for failover and/or
stateful update information
interface-policy Set the policy for failover due to interface failures
key Configure the failover shared secret or key
lan Specify the unit as primary or secondary or configure the
interface and vlan to be used for failover communication
mac Specify the virtual mac address for a dynamic interface
polltime Configure failover poll interval
timeout Specify the failover reconnect timeout value for
asymmetrically routed sessions
exec mode commands/options:
active Make this system to be the active unit of the failover pair
exec Execute command on the designated unit
reload-standby Force standby unit to reboot
reset Force a unit or failover group to an unfailed state
As you can see, the ASA tells us that there are different additional command parameters after the "failover" command that can be used. Some of them can be used either in Exec or Configuration mode.
- Jouni -
Calendar gone from N73 Active standby
I have recently installed some new themes but lost my calendar from the active standby screen. When I change the theme back to standard nokia one, and turn active standby off then on again, it returns.
I am getting very bored with he nokia theme but use the calendar display too much to do without it.
I have never had this problem before. All software/firmware is up to date.Back up all your data to your PC using PC Suite's content copier, and then shut down your phone. Hold down 3 buttons: GREEN, 3 & * while switching on your phone. Make sure don't release your fingers till the phone ask for pin. You'll lose everything that's on your phone memory, and if you restore that from a back up, you'll be back to where you started, but this seems to have worked. You'll also lose things that your network operator may have installed. But oh well. Still no idea why it happened in the first place though!
-
N86 active standby plugin area
Hi, are you able to remove or change the items shown in active standby plugin area? Of the 4 items on the screen, I will never use chat or share my photos and can't set up email making all three options unnecessary. Any ideas?
you can indeed change shortcuts and active standby
Modify the standby modeTo change the look of the standby mode, selectMenu > Tools > Settings and General >Personalisation > Standby mode. The activestandby display shows
application shortcuts, and
events from applications
such as calendar, e-mail,
and music player.
To change the selection
key shortcuts or the
default shortcut icons in
the active standby mode,
select Tools > Settings >General >Personalisation >Standby mode > Shortcuts.To change the clock shown in the standby mode,
select Menu > Applications > Clock andOptions > Settings > Clock type.You can also change the standby mode background
image or what is shown in the power saver in the
device settings.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520 -
N81 How to Show calender at active standby
Hi, i just bought a N81, but i just cant seem to get the phone to show the calender details for the day at the active standby mode(the main page). I can do it previously on my 6280.
Anyone can help?12-Jun-2008 11:42 AM
psychomania wrote:
Pass, it reads to me like they want to change the active standby shortcuts and can't find which application to use in the phone.
It reads like that to me too.
Grayburn @ www.nokiausers.net & www.dailymobile.se....come say Hello!!!
If you appreciate ANY help from a member,then show it by clicking on the Blue Star button, cheers
Maybe you are looking for
-
Time doesn't display when I close phone, record album does.
When I close my Style, I used to get a thirty second image of the time on the external screen. Now I get a picture of a record album. I don't have the music player running, and the clock's options don't lend any clues. Thanks in advance for any he
-
It's really been puzzling me, I've never logged in the Apple site on a laptop before - I have been getting the same message 'Unable to verify iCloud account' every time I try and erase all data and content from my iPhone 4s. When I go to iCloud on my
-
I have been a firefox user for quite a while and have loved it. I can't even count how many people I convinced to switch from boring old Explorer to Firefox, but after this latest update, I got so frustrated I uninstalled it. I just reinstalled it ag
-
How do you determine a process or sessions isolation level.
We are using COM+ components to issue database statements against an Oracle 8i database. COM+ has a property that allows you to set the isolation level. Is there any tool or query that would allow me to verify the isolation level in use by a session
-
Why is there no way to download the latest version of SCM by itself? There is not even a mention that version 9.0.4 is available with iDS 10g. At least when I go to the SCM documentation page, I would like to see a link to the 9.0.4 SCM documentation