Calibration of HP8753E in labview

Driver instrument pour la calibration du HP8753E sous labview
Driver instrument' for the calibration of HP8753E in labview
Bonjour,
Je suis entrain de développer une interface utilisateur sous labview 8,5 pour interfacer un analyseur de fréquence HP 8753E, j'ai pas pu trouver une solution (normalement avec les driver d'instrument) pour faire la calibration du l'analyseur (remarque la calibration peut se faire manuellement mais je doit le faire avec labview)
j'espére que ma question est claire, merci de me répondre
Cordialement
Hello,
I am currently developing a user interface in labview 8.5 to interface a frequency analyzer HP 8753E, I could not find a solution (normally with the instrument driver) to the calibration of the analyzer (note the calibration can be done manually but I must do with labview)
I hope that my question is clear, thank you for answering me
cordially

duplicate

Similar Messages

Driver instrument pour la calibration du HP8753E sous labview--Driver instrument' for the calibration of HP8753E in labview

Bonjour,
Je suis entrain de développer une interface utilisateur sous labview 8,5 pour interfacer un analyseur de fréquence HP 8753E, j'ai pas pu trouver une solution (normalement avec les driver d'instrument) pour faire la calibration du l'analyseur (remarque la calibration peut se faire manuellement mais je doit le faire avec labview)
j'espére que ma question est claire, merci de me répondre
Cordialement
Hello,
I am currently developing a user interface in labview 8.5 to interface a frequency analyzer HP 8753E, I could not find a solution (normally with the instrument driver) to the calibration of the analyzer (note the calibration can be done manually but I must do with labview)
I hope that my question is clear, thank you for answering me
cordially

YET ANOTHER DUPLICATE

Read Calibration Due Date with Labview

Greetings Everyone,
     I figured out a way to read the configuration of my PXI-1044. I would like to read the External Calibration section of the Calibration Tab in MAX for my PXI-5114 and PXI-4065 (Last Calibrated and Recommended Next Calibration Dates) by using Labview to read it. The preferred format I am looking for is similar to the configuration of my PXI-1044 that extracts data in a Tab delimited format. Thank you in advance for any information that this forum can shed on this subject.
Regards,
Scott
Solved!
Go to Solution.

Hi Dennis,
     Thanks once again for your reply.
     I searched all examples that are loaded into the computer and the search came up empty for the file you mention. I even searched for the file on Google and stil came up empty. Is this file something that came with Labview 2011 or Labview 2012? If so I don't have access to that since all computers are running Labview 2010.
     I appreciate your efforts in helping me out. I'm still a little confused as to what System Session Refnum is to be expected on the input of Measurement I/O>System Configuration>Hardware>Property Nodes (Hardware). Looking at the slew of stuff that the property node offers and tying a couple to Text Indicatorsto them it looks like the stuff I'm after. The only thing I would need is to connect the PXI-4065 and/or PXI-5114 to this node in order to extract the data that I need. Property nodes are very new to me and I'm sure they can be very useful. This information is going to be used for a Test Rack Self Test program that I'm developing above and beyond the embedded self test protocol that NI has in its software. I look forward to your response or anyone elses that will push me forward in my education of this software package.  Thank you in advance.
Regards,
Scott

How to calibrate analyseur HP 8753E with Labview??

ghabri
Envois : 1
0 Compliments
Driver instrument pour la calibration du HP8753E sous labview
Driver instrument' for the calibration of HP8753E in labview
Bonjour,
Je suis entrain de développer une interface utilisateur sous labview 8,5 pour interfacer un analyseur de fréquence HP 8753E, j'ai pas pu trouver une solution (normalement avec les driver d'instrument) pour faire la calibration du l'analyseur (remarque la calibration peut se faire manuellement mais je doit le faire avec labview)
j'espére que ma question est claire, merci de me répondre
Cordialement
Hello,
I am currently developing a user interface in labview 8.5 to interface a frequency analyzer HP 8753E, I could not find a solution (normally with the instrument driver) to the calibration of the analyzer (note the calibration can be done manually but I must do with labview)
I hope that my question is clear, thank you for answering me
cordially

duplicate post
Please do not post the same question on multiple boards.

Where do I get HP8753ES drivers for Labview 8.2?

Hello,
I am in the process of updating some Labview code to 8.2. Where do I find drivers for the HP8753ES that is compatable with Labview 8.2? I looked at the NI website and the drivers listed are for Labview 8.0, will they work with Labview 8.2? There are also "project style" of drivers, is there a difference?
Regards,
Kaspar
Regards,
Kaspar

I don't know why you think you 'have' to use the plug&play driver instead of the project style but there is no subVI called HP8753 Collect Data and none of the VIs in the driver call a function called HP8753 Collect Data. There is a subVI called HP8753 Collect and Display Data. What exactly are you doing that you cannot find a subVI? Do you have the driver functions on your palette? Where exactly did you place the unzipped folder. If you have done the installation correctly, you will have a palette just like the one below and there is no need to search for anything. They will just be there.
Message Edited by Dennis Knutson on 09-24-2007 12:08 PM
Attachments:
8753 palette.PNG ‏6 KB

Able to do calibration in labview ?

i currently doin a temperature control system using labview whereby my thermocouple is connected a thermocouple amplifier, because i connect using breadbord so the value i obtain is quite far from the data sheet given, so i need to do the calibration in order to show the temperature at my control panel accuratey, may i know got the graph function in LabView 8.0 can help to calibrate it without doin the calibration manually . The manually is for example cook the water then take the note down every 10 degree of the temperature that rising and then plot the graph and linearise it. Another question is my temperature function icon shown floating when i inputing the signal voltage to my usb 6008, got anyway to make it constant?

I think this can be done easily with in Labview it self by using scales. and then using that scale for the input voltage you want to measure. Se attached JPG of Measurement and Automation explorer where I have set scale to measure input from eddy current probes and also changed the scaled units to mm.
Attachments:
scale.JPG ‏76 KB

Comment transformé le résultat d'un teste de limite par analyseur de fréquence HP8753E en un fichier texte avec labview

Bonjour,
j'utilise labview pour commander un analyseur agilent hp 8753E pour faire des teste de limite de cable le résultat est identifier par les status registre bytes B, alors comment on transformen le résultat du teste en un fichier texte ?

Bonjour
Le VI "write to spreadsheet File" enregistre les données dans un fichier TXT.
Cordialement
Mart G

Open and close multisim contact with LabVIEW

Can I open and close multisim contact with labview and read the receptor estatus (p.e. lamp)?
Thanks.
Attachments:
Dibujo.JPG ‏13 KB

Hi Guddan,
I created a RFC having a query which is taking a long time to execute. So i want to close RFC connection with portals which is via java connector(JCO) before that query and open the connction again after that query.
I guess i will need to understand your requirement a little more in detail, as i understand you have an RFC which has a query within to fetch some data and is taking a long time to do so. In the meantime you don't want to keep the connection open?
My question would be, Is the role of this RFC to only execute the query and fetch the data or does it do something else?
If it does other things and these are independent of the query execution, then you can span a parallel call within the RFC to execute the query and in the meantime the RFC does the other things (or vice versa) hence reducing the overall time taken.
If the sole purpose of this RFC is to execute the query, then you will not be able(i mean to say there is no simple and direct way of doing this) to close the connection after the Query is started and re-establish the connection after its execution, for a simple reason that - how will you know if the query has completed it's execution, so that you can establish the connection back.
Alternate solutions, make this a two way asynchronous call, 1) You invoke the RFC asynchronously and close the connection, the RFC in turn will execute the query and transfer the data to JCO via another RFC call.
If this needs to be a synchronous call, then you will need to optimize the query to its best.
Regards,
Chen

LabView Exe Application file not launch Excel application for report generation

Dear All,
I created one LabVIEW application file for report generation (using Excel Template).
While I run the program in programming mode it works well and create the report file in the specified path.
After creation of the application file(exe), it gives the correct path of where the excel template is placed. The same path is given to New Report.vi, but it gives the error 'File Not Found'.
Tell me, is any other configuration required for generating Excel reports? (During exe application mode)
Give me the solution.
Thank You
Jegan.

Hello,
Most likely you are encountering a problem of stripping and/or building paths. Probably the easiest thing to do is put a couple indicators on your front panel for the path or paths you care about, build your exe, and make sure you are really using the path you'd like. If you always put the report at some deterministic place relative to the exe (that is, even it the exe is moved, it will go with the exe and remain in the same relative path location, then you can use the Current VIs Path funtion found in the ... File I/O -> File Constants palette as a start path (where you will want to strip at least the exe name off of course).
I think this will bring some clarity to the issue!
Best Regards,
JLS
Best,
JLS
Sixclear

Error involving Report Generation Toolkit and Labview Run Time Engine

Developed an application using LabVIEW 6.1 and LabVIEW Report Generation Toolkit for Microsoft Office 1.0.1. From there, tried to build a shared application for use with the LabVIEW Run Time Engine. The Run Time version functions properly until "New Report.vi" is called and then an error is generated, code 7, calling out "Open VI Reference in New Report.vi" could not be found. When building the application, I did include the "NI Reports Support" in the advanced installer options. The machine used for original development and application build is running Windows XP Pro and Office XP. Any suggestions??

I am having the exact same problem but with LV 6.1 and M/S WORD 2000. It appears that the "New Report.vi" is trying to open "C:\APP.DIR\Word_Open.vi" and "C:\APP.Dir\Word_Open_Document.vi" by reference. The "OFFICE 2000.TXT" says that "_exclsub.llb and _wordsub.llb must be added as support files when building an application or a dynamic link library with the application builder." I added them as Support Files and I copied them to the "C:\TESTER\" where the TESTER.EXE is and I still get ERROR 7 in "NEW REPORT.VI" at VI OPEN REFERENCE.
Do I need to make a "C:\TESTER\DATA\" sub-dir and put the support files there?
I am building on MY COMPUTER on F: Drive on a network and transporting files to the real Tester.
I displayed my App.Property of APP.DI
R at start up and it is C:\TESTER\ ! How would my application know that "Word_Open.vi" and "Word_Open_Document.vi" are actually inside the _wordsub.llb?
Any ideas ?
Greg Klocek

Why do I get "The exception Privileged instruction (0xc0000096) occured in the application" error message when exiting LabVIEW 6.1?

I have created a vi that uses the LV-GPIB and database connectivity vis. The program runs fine and it ends execution by running the "Close Database Connection.vi".
After closing out my front panel windows and exiting LabVIEW 6.1, I get an error dialog box that reads the message "The exception Privileged instruction (0xc0000096) occured in the application". What does this error mean and how do I resolve it?
Thanks,
Taf

Hi Taf,
Given the broad scope of your application, it may be best to try and isolate the problem down by taking out parts of your application and simplifying it down as much as possible until you can get a consistent version that throws this exception. I would first try to take out either the GPIB or database connectivity portions of the application to narrow down our problem. This error generally occurs when accessing DLLs and external applications, so I wouldn't be surprised if it's the GPIB or database. Let's try to see exactly which one it is and then we can dig deeper into that part of the code. Thanks for your cooperation!
Jeremy L.
National Instruments
Jeremy L.
National Instruments

How to run downloaded drivers on Fresh Install of Labview 6.1 on a Mac G4 OS 9

I have just completed a fresh install of Labview 6.1 on an Macintosh G4 running OS9. I can run it and it seems to work just fine. I downloaded some drivers for an oscilloscope (HP 546XX) to run with an HP 54603b. When I installed, I went to open the 'Get Started.VI' I get a freeze and have to force quit out of labview. I am not sure how to resolve this. I am pretty sure that it is independent of the device, since I can open the vi's at least on another computer with no hardware attached. So I guess to boil my situation down. I have 2 questions:
-How do I get a fresh install on a mac G4 OS 9 to run downloaded drivers from the internet
-How do I ensure that I have the hardware configured on
a macintosh to run properly.
I really have little experience with macs so I am not really sure what my options are or what could be the problem so any assistance would be much appreciated.

Hmmm. I wonder if NI-VISA isn't installed correctly on this machine.
When LabVIEW loads a VI that uses a VISA name control on the front panel, it queries VISA for the installed devices. Sometimes this takes a few seconds, but maybe in your case, something has been corrupted and it's hanging.
To try to narrow this down, first run the separate program "VISAConfig". This should list your devices. If this works, this means it's pretty likely that VISA is installed correctly.
Next, run LabVIEW. On an empty front panel, select the "Controls->I/O->VISA Resource Name" and place it on the front panel. When you click on the arrow on this control, you should see a list of your devices. If this works, then that indicates that LabVIEW is successfully talking
to the VISA software.
If both of those succeeded, then we have to take a closer look at this particular instrument driver. Can you drop other VIs (say, Initialize or Close) without hanging?
If either of the first two steps fail, I'd suggest that you reinstall the VISA software. You may want to try the latest version of NI-VISA (from ni.com), but first confirm that it supports LabVIEW 6.1.
I hope this helps.
Brian

Convert PXIe-8135 controller to dual-boot Windows 7 and LabVIEW RT

Hello. I have a PXIe-8135 controller that originally was just running Windows 7. We are trying to convert it to a dual boot system to also run LabView Real Time. (There is host computer that will run LabVIEW 2014 with the RT module, and the controller will become a target).
I have created a FAT32 partition on the hard drive of the controller. Now, I’m trying to install the real-time OS with a USB flash drive made using the MAX utility, but I cannot boot using the USB drive for some reason. I keep getting the message “waiting for USB device to initialize”.
In BIOS, legacy USB support is [ENABLED] and boot configuration is set to [Windows/other OS]. I’ve tried removing the drive, waiting, and reinserting. I’ve tried two different USB drives (both 8 GB, different brands).
I’m not sure what to do next. Apart from the USB boot issue, is converting the PXIe-8135 even possible? I read about SATA/PATA hard drive issues with older controllers, but I don't know about this one.
Thanks, in advance, for your help!
-Jeff
Solved!
Go to Solution.

Per Siana's licensing comment, more information on purchasing a deployment license if you do not have one for this target can be found here.
The RT Utility USB key is used to set up non-NI hardware with LabVIEW Real-Time, but you should not need it in this situation to convert to dual-boot (*). Try this:
1. Since you already have a FAT32 partion created, go into BIOS setup and change to booting 'LabVIEW RT'.
2. The system will attempt to boot LabVIEW RT, see that the partition is empty, and switch over into LabVIEW RT Safe Mode. (this safemode is built into the firmware, which is why you don't really need the USB key).
3. The system should come up correctly and be detectable from MAX, and you can proceed with installing software.
4. To switch back to Windows, go back to BIOS setup and choose 'Windows/Other OS'
(*) One area where the USB key is helpful on a dual boot system is with formatting the disk. If you want to convert from FAT32 to Reliance on the partition designated for LabVIEW RT, the USB key lets you attempt to format a single parition and leave the rest of the disk untouched. If you format from MAX, the standard behavior is to format only one RT partition if found, but if not found, it will format the entire disk. Formatting from MAX on a dual boot system is consequently riskier and you could lose your Windows partition.

Some fonts are not shown correctly in LabVIEW 2012

I found a bug related with fonts in LabVIEW2012 f3 KR.
- When I select NI7SEG in font selection dialog, right font is not shown in the example box.
- Draw text at point.vi shows same problem for some fonts while other fonts are working.
I reported it to Korean NI. As far as I know, this was not reported in previous versions and I couldn't find any related documents in Google.
So, here I would like to know whether it is related with only Korean version. Please let me know if English version is OK.
* OS: Windows 7 32bit KR

Just now, I installed LabVIEW 2012 f3 (32-bit, English) and checked for the issue. But the font(NI7SEG) was not shown properly in VI either.
- Both of Korea and English version of LabVIEW 2012 on Win 7 Korea OS shows wrong results. It is same on 64-bit OS.
- LabVIEW 2010 but on same PC shows correct fonts.
Is there a limit of number of fonts in LabVIEW? There are more than 100 fonts are shown in the "Selection Font" dialog and I can divide them into 3 groups by sequential order. I find that all fonts in the 3rd group are not applied correctly.
(1st group)
Arial Unicode MS...
Bookshelf Symbol 3....
Windings 3
(2nd group)
@Arial Unicode MS...
@Terminal
(3rd group)
Arial...
Consolas...
Courier...
Licida Console...
NI7SEG...
Verdana

Comunicação entre Labview e ANSI's.

Estou definindo Projeto de Graduação e estou interessado em trabalhar na integração entre Labview e ANSI's na análise de elementos finitos. Gostaria de saber se alguém possui alguma informação sobre o tema.

Voce poderia ser mais especifico com relacao a informacao que voce esta precisando?
Atenciosamente
Filipe A.
Applications Engineer
National Instruments

Calibratio​n of HP8753E in labview

Similar Messages

Maybe you are looking for

Calibration of HP8753E in labview