"Call back" dial up internet? Help!
Hello and help! I'm in Ukraine trying to use dial up internet in my apartment. Dial up in Ukraine is done by buying a card that provides you with a pin code that you use to make an account with a third party provider. The time you spend on the itnernet is "pre paid" in essence and when you run out of time
you buy a new card and scratch off a new code.
There are two ways to connect. The first is to dial straight into their server from your computer/phone line (which means you have to pay for the phone time since you're the one who dialed out and this can get expensive). The second option is called "call back." "Call back" meands my computer dials the company then the company dials me right back with an internet connection that I start using. I have been trying to get call back set up for days and
have not succeeded. HELP!
The name of the service I am using is called Superweb (ww.superweb.com.ua/eng). I am trying to dial the 251 1212 number. I am using pulse setting. The error message I'm getting is "Could not negotiate a connection with the remote PPP server. Please verify your settings and try again."
The directions which the company normall gives to PC users are to go into "network" settings, go to "advanced", then "dial up preferences," check off "callback" and then type in the number (not sure if they mean the number I'm calling 215 1212 or my land line number but easy enough to try both).
Please, please help me solve this. Where is the call back option on a mac?
Thanks. I can't wait to hear from you.
More technical details: I have the first generation of the white 12 inch iBooks. I am running Tiger (no updates just original version).
hi ,
access the setup page of the router using http://192.168.1.1 "admin" is the password....go to the wireless section and then to advanced wireless settings.....
turn "off" the AP isolation...reduce the Beacon interval to 50 and reduc the RTS and fragmentation threshold by 40 each....
let me know if this works.
Similar Messages
-
I seriously hope someone can help me, I'm getting very frustrated. Until 3 weeks ago I was sharing a dial up internet connection (I know but I am rural and it's all that is available, I literally have no other option) printer etc on up to three computers. Desktop running XP and two laptops also running XP. Then out of the blue I lost my wireless signal. My router is a WRT54G. I have literally tried everything. I updated the firmware, the router is working fine it shows up on each computer but they will not communicate. The two laptops see each other but the desktop doesn't see either of them. I know that it has something to do with sharing the internet connection but I don't know what I need to change to get it back. I have literally asked everyone I know, I have searched and searched, I have had two people in the field and they can't figure it out but I KNOW this works I have done it for over 2 years with no problems at all.
I have even tried a new router but that isn't the problem, all the cables work, everything is working except it won't share.
Please someone help! Thanks in advance!hi ,
access the setup page of the router using http://192.168.1.1 "admin" is the password....go to the wireless section and then to advanced wireless settings.....
turn "off" the AP isolation...reduce the Beacon interval to 50 and reduc the RTS and fragmentation threshold by 40 each....
let me know if this works. -
Courtest Call Back Query HELP!!!!
My name is Michael Love, I am having issues getting counts for Courtest Call Back. I need help building a query to get a count of all customers that Accepted Courtesy Call Back. I am also trying to fine out (of those that accepted Courtest Call Back) how many of them completed the process by connecting to a rep.
I need distinct counts...Michael,
How this might be accomplished varies quite significantly based on how the queue call back was programmed and other parameters of scripts in your call center.
The most concrete way would be to have your script write to a database when a callback is requested, and update that record when a rep is successfully connected via the Connect step. From there you could program a quick web interface or otherwise to provide you that information.
Regards,
Tanner Ezell
www.ctilogic.com -
I have a late 2011 MacBook Pro 13" and bought a brand new iMac 27" last week.
I tried to transfer data (musdic & photos) via Thunderbolt, but i did not run, my system always
tries to transfer data via WLAN, but that would last more than 80 hours.
I tried to get some help from the Apple Support, but unfortunately they couldn't help me.
A promised call-back from the next higher support-level has not been done.
Does anybody know what the problem might be.
The Thunderbolt-cable is brand new.Instead of using Migration Assistant, the best way is to use the Target Disk Mode, so you will save headaches (Migration Assistant creates a new user with the transferred data).
To do this, just connect both Macs with the Thunderbolt cable, and then, start the MacBook Pro holding the T key, so a Thunderbolt or FireWire icon should appear on the display. After that, go to the iMac, open Finder, and the hard drive of the MacBook Pro will appear on the Finder sidebar as an external drive, under "Devices". Just access to it, go to the folders with your iTunes and iPhoto libraries, and copy them to the iMac -
Can apple help me find my iPod touch 5g??? I have already reported it to the police and they haven't called back, i also have the find my iPhone app in it but I don't have the location thingy turned on so what else can I do to locate it pleazz help this iPod is relly valuable to me I had gotten it for Christmas and now I proved that I can't be trusted with it HELP :c
Police don't "track down" lost items, per se. They'll keep your information on file in the event that someone finds your iPod and turns it in. Otherwise, there's nothing the police can or will do in regards to finding lost property.
Sorry, but your iPod is most likely gone for good.
Regards. -
my iphone 5 is not getting audio during calls, im not hearing anything unless i put it on speaker. Can you help me is this a software problem its very annoying for every call i dial or recieve i have to put on speaker. Please help me apple please.
There's a whole lot to read in your post, and frankly I have not read it all.
Having said that, this troubleshooting guide should help:
http://support.apple.com/kb/TS1538
In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it. -
URGENT - Help on RMI & Proxy - Call back prob
Hi
I have made small RMI, where RMI server is running in Webserver [ which is not even Proxy]. It is working fine for all the clients except clients under firewall/Proxy.
Please let me know, Can we implement RMI Server able to call back the clients [ which are under proxy ]
If so , what modifications i have to do ???
Note
1. Client Able to access the RMI Server. But From the Server, i can not able to Call back the Client.
2. I am passing clientRef through remotemethod on the remoteObject . Then the ClientRef will be stored in Server. When trying to call back throgh the ClientRef, I am getting Exception, RemoteException such that i could not able to connect/not found. The same concept is working if the Clients are not in Proxy
Please help immediately.
Sampath Ramanujan.If I am not wrong RMI multiplexing protocol wsa a temporary solution to this problem. It was introduced in JDK 1.02 pre release of RMI. But this Protocol has been disabled since JDK 1.2.2.
If however JDK1,4 if the improved RMI protocol is biderectional this will solve the problem. -
I need a multiple message voice mail app for Iphone 4S that also provides an auto-attendant, e.g the caller can dial 1 for one of business's or 2 for the other. Each of these options will need to have a different voice mail greeting. Help please?
There are no alternative voicemail apps - the core functionality of the phone can not be replaced.
You'll have to look for an external service, that can then forward calls for each caller onto the correct phone.
At our business we use Voipfone.co.uk which allows multiple phone lines to come into one VOIP account. -
Re: Forte and OrbixWeb call-back
We have created a business process manager (BPM) layer between our client GUI
and business model objects that supports Java call-in/call-out. This enables
switching out the Forte windows with Java windows for a web solution with
minimal code re-write.
We were able to get most functionality to work as per our design, which
included registering a call back function from a Java GUI in the BPM, but had
to make some sacrifices due to a Forte bug, at least under 3.0.D. We turned
in case #38434, detailing errors when we tried to fire a callback method with
parameters, example below ("callback" was the Java object passed in.)
method TestIIOPBackend.FireCallback(input message: Framework.string)
begin
if callback != nil then
task.part.logmgr.putline('Firing callback');
//WORKS
callback.CallMe();
//ERROR!
callback.CallMeString(message);
else
task.part.logmgr.putline('Callback not set');
end if;
end method;
This may have been fixed in 3.0.F, we found a way to work around it in our
design and haven't investigated since.
-DFR
Ngai* Stuart <[email protected]> on 01/20/98 09:14:28 AM
To: '[email protected]' <[email protected]> @ INTERNET
cc:
Subject: Forte and OrbixWeb call-back
Has anyone actually tried the tech note 11153 "Java call-in/call-out and
Forte
Anchored Objects"? I'm trying to verify the callback mechanism from
Forte to
an IIOP Java client. Thanks.
<<< Stuart Ngai (416)359-4306 [email protected] >>>
------ Message Header Follows ------
Received: from pebble.SageIT.com by notes.bsginc.com
(PostalUnion/SMTP(tm) v2.1.9c for Windows NT(tm))
id AA-1998Jan20.101336.1771.787915; Tue, 20 Jan 1998 10:13:36 -0600
Received: (from sync@localhost) by pebble.SageIT.com (8.6.10/8.6.9) id HAA03868
for forte-users-outgoing; Tue, 20 Jan 1998 07:25:41 -0800
Received: (from uucp@localhost) by pebble.SageIT.com (8.6.10/8.6.9) id HAA03862
for <[email protected]>; Tue, 20 Jan 1998 07:25:39 -0800
Received: from keeper.nesbittburns.ca(192.139.71.50) by pebble.sagesoln.com via
smap (V2.0)
id xma003860; Tue, 20 Jan 98 07:25:19 -0800
Received: from NesbittBurns.ca (tds223.nesbittburns.ca) by
keeper.NesbittBurns.ca (4.1/SMI-4.1)
id AA22591; Tue, 20 Jan 98 10:23:47 EST
Received: from nbtormail02.nesbittburns.ca by NesbittBurns.ca (5.x/SMI-SVR4)
id AA12961; Tue, 20 Jan 1998 10:26:54 -0500
Received: by nbtormail02.nesbittburns.ca with SMTP (Microsoft Exchange Server
Internet Mail Connector Version 4.0.995.52)
id <[email protected]>; Tue, 20 Jan 1998
10:27:52
-0500
Message-Id:
<c=CA%a=_%p=Nesbitt_Burns_In%[email protected]>
From: "Ngai, Stuart" <[email protected]>
To: "'[email protected]'" <[email protected]>
Subject: Forte and OrbixWeb call-back
Date: Tue, 20 Jan 1998 10:27:39 -0500
X-Mailer: Microsoft Exchange Server Internet Mail Connector Version 4.0.995.52
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
Sender: [email protected]
Precedence: bulk
Reply-To: "Ngai, Stuart" <[email protected]>Peggy,
1) Do you have experience with PowerBuilder and Forte' applications running at
the same time on the same (laptop) computer? Here I'm thinking
about any potential resource constraints? Memory Requirements?As log as you are using Win95 or NT you should not be concerned about WIN-resources. Memory depends more on what your 2 tier PB application requires than what your Forté would require.
Cheers,
Troels
Lindhard Forté Solutions
-----Original Message-----
From: Peggy Lynn Adrian [SMTP:[email protected]]
Sent: Thursday, January 15, 1998 10:31 PM
To: [email protected]
Subject: Forte and Powerbuilder Experience Needed
I sent this query to Forte support but maybe someone out there can help me
with practical experience
with the following?
---------------------- Forwarded by Peggy Lynn Adrian/AM/LLY on 01/15/98 04:30
PM ---------------------------
Peggy Lynn Adrian
01/14/98 03:55 PM
To: [email protected]
cc: Peggy Lynn Adrian/AM/LLY@Lilly
Subject: Forte and Powerbuilder Experience Needed
1) Do you have experience with PowerBuilder and Forte' applications running at
the same time on the same (laptop) computer? Here I'm thinking
about any potential resource constraints? Memory Requirements?
2) Can PowerBuilder and Forte' applications call and interact with one
another?
The Forte' application will need to interact with the PowerBuilder application
to pull out information maintained by the PB application. -
Keychain Access and dial-up Internet connection problem
For the past two days I was unable to connect to my dial-up Internet on my Sawtooth. It's got 10.4.11. The Internet phone connections checked out fine. I even tried my old Dell and it got on the Internet ok.
I checked the Internet settings and thought they were ok. My Internet provider's website help section on set-up is worthless for Mac OS X. They only show instructions for OS 8 & 9!! Found some other dial up providers set-ups and went by them.
After trying to get the settings correct, right before I tried to connect to the 'net, a dialog box called "Confirm Access to Keychain" always came up. The box said: "pppd wants permission to use the "PPP Password" item from your keychain. Do you want to allow this? Deny, Allow Once, or Always Allow?" I had read on the Mac OS X help that allowing the keychain always permission to access to use passwords when going online isn't a good idea... I always kept clicking "Deny" and I couldn't connect. Just got brave a bit ago, and clicked on "Allow Once" and here I am on the Internet!!! This keychain business was the problem the whole time!
My question is how in the world did the Keychain get involved, as I didn't even ask it to save the Internet password etc. The Keychain shows PPP password listed three times and I believe a Dashboard certificate. Would it be ok to delete the three PPP password listed? Was going to, but was afraid I'd really mess up Tiger... I don't want to mess with Keychain at all, since I've read in the past that it can really cause headaches if not used correctly.
Any help would be greatly appreciated! Thanks.
silverado93Yes, you can delete those PPP entries if you don't mind entering the Password each time you connect, though I'm on dial-up & have Always Allow checked without problems or a decade or so.
-
How do I Translation Route a call back into CVP?
This is ICM 8.5, CVP 8.5 and Avaya CM 5.2. I'm trying to configure the system to be able to Translation Route a call back into CVP that originally started in CVP. I've read and read Cisco documentation that talk about various ways it can be done but I think I really need step-by-step instructions to figure out what I've done wrong. I'm happy to explain it in gory details if anyone wants to help me troubleshoot. However, I think it would be simpler if someone can point me to a document that outlines a successful configuration and I can find my own mistake.
Thanks clearbluelou, some of this was very helpful, but I had to set my translation routes up differently. Kris Lambrecht's post was very helpful, but also introduced some confusion, which looking back was very simple...hindsight is always that way right?!?!
I am going to list out the configurations I used to make this work, most of which are what's listed in the Type
8 setup in Kris's post starting with Step 7 except its for a Type 10 Network VRU; you don't use Type 8 anywhere, but the configuration is very similar.
Assumption is that you already have an existing system and are routing calls to CVP already so a lot of the steps in the config guide are already done.
References below are to "Configuration and Administration Guide for Cisco Unified Customer Voice Portal Release 8.5(1)" starting on page 109, step 7:
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/customer_voice_portal/cvp8_5/configuration/guide/ConfigAdminGuide_8.5.pdf
Here's the details of my implementation:
ICM 7.2.7
CVP H323, Type 10
Avaya PBX connected with a PG also running CTIOS
Destination is the CVP Servers/CVP PGs (PG1), call transfer is originating from an Avaya PBX connected to ICM via a PG/CTIOS server (PG2).
1. Build a new Service under destination PG, CVP in this case, as outlined in Step 7 from the CVP Config Guide.
- Service
Peripheral Number: 2
Peripheral Name: Pre_Route
Name: CVP_PG1.Pre_Route
- Route
Name: CVP_PG1.Pre_Route
-Peripheral Target
Not required
Labels
Not Required
2. Build Network Trunk Groups, as outlined in Step 8 from the CVP Config Guide:
- Network Trunk Group
Name: CVP1_NTG
Peripheral: CVP_PG1
PeripheralNumber: 200
PeripheralName: CVP1_NTG
Name: CVP_PG1.CVP_NTG
Trunk Count: Use Trunk Data
3. Build Translation Routes using the TransRoute wizard, I built a pool of 10 DNIS 1000-1010; these are dummy DNIS; outlined in Step 9 from CVP Config Guide; here's what they should look like in
the TransRoute explorer when finished:
-Translation Route
Name: TR2CVP1
Type: DNIS
-Route
Name: CVP1.1 - CVP1.10
Service Name: CVP_PG1.Pre_Route
-Peripheral Target
DNIS's: 1000-1010
NTG: CVP1_NTG
-Label
Routing Client: PBX_PG2
Labels: 1000-1010
Label Type: Normal
Customer: None
4. Configure Trans Route DNs 1000-1010:
- Have to be built on the Avaya pointed to a VOIP gateway with Session Target equal to the CVP Call Server (or GK).
- Add Translation Route DNISs in CVP Call Server Configuration under ICM Tab.
!!!Make sure you "Save and Deploy"!!!---->If you don't calls will show up on the ICM as new calls on the Translation
Route DNIS's under your CVP Peripheral.
5. Build Dialed Numbers in ICM:
-Extension 2000 is the dialed number Agents on the Avaya transfer to.
-VDN 2000 on Avaya PBX should be routed to an Adjunct Route step which will send a route request to PG2 and kick off a script in ICM.
-You have to build a dialed number in ICM Dialed Number Explorer under the PBX peripheral (PG2 in my example) PG2.2000, and point it to a CallType and subsequently a script, for example "Avaya2CVP".
6. Build your ICM Call Routing Script: (follow's ClearBlueLou's description)
- Route the call through typical CVP call setup initialization nodes
-Route to Trans Route to VRU node with "CVP_PG1.Pre_Route" as the service selected, and "TR2CVP1" Trans Routes
selected.
-Then send to a microapp.
Your test call should have exited the success connection of the TrasRoute to VRU node and will continue routing with all call variable information will route (and show up in TCDs and RCDs) under Dialed Number PG2.2000. -
Meeting Place and Webex Call Back Failing
Hi
Meeting place 8.5 with WebEx scheduling, SIP trunk to CUCM 8.5.
Calling in using the specified number configured in call manager completes over the SIP trunk however call back from webex fails.
Error:
WebEx call back failed; no answer.
Problem is I never recieve a call. I have enabled Webex call backs in webex.
Seems like there is an issue on either MP or CUCM.
Just looking for some ideas as I am stumped.This turned out to be a few things:
1) I needed to configure a SIP proxy to CUCM from meeting place. This was the CUCM IP address and TCP port number.
2) The SIP trunk security profile needed to be reconfigured for this trunk.
3) E164 was being used so I created a translation pattern to strip the + for the CSS associated with the RP.
A few things learned along the way.
1) The "activity" command ran from a SSH prompt with allow you to simulate a call from meeting place. Option 4, enter the number to dial and "f" for port.
2) In meeting place - Services -Logs - System Information Capture - Loading the index file and under the CCA SIP LOG is the error being returned by CUCM. In my case it was Warning: 399 CSLCCM1 "Unable to find a device handler for the request received on port
3) Command "cptrace" again from the SSH prompt will allow you to view the digits being sent from webex to meeting place.
I hope this information helps someone... -
RMI call back - How to refer to the client project from the server project?
Hi, I am working on an RMI assignment which basically needs me to use the RMI call back for the server to notify the clients.
I have 2 projects , one for the client and another for the server.
In the client project, I have a client interface and the main client class implements this interface.
In the server project, I have a server interface and a class that implements this interface.
I can use the server interface in the client project's code by adding the server project in the path of the client project. it lets me use the server interface in the code if I put "import.." statement.
But the issue is I can not do the same to access the client interface from within the server project's code. Since that will be a circular reference, the compiler does not let me use the client interface from within the server's code. This is putting me in a great difficulty and I am stuck here. What should I do so that I can use the client interface and the compiler won't complain?
Thanks for any help..
Regards.. jsLet me explain what I tried: I manually generated stub class of the client using the Eclipse IDE as mentioned in my previous message. The StockMSClient_Stub.class got created in my client project.
The common project has the 2 interfaces - one from the client and one from the server.
I have added reference to the common project from the client and server projects to use the interfaces.
With the above mentioned in place, when I run the server project, the registry binding of the server objects is very fine. But I am getting error in the applet at the line where I am passing the client object to the method provided by the server interface. The following is the code snippet in the applet where I am getting the error.
specifically the line: String response = objs.login(userId, password, smsClient); ====================
public void login() {
Registry reg = null;
String userId = "test";
String password = "test";
this.smsClient = new StockMSClient();
try {
reg = LocateRegistry.getRegistry(rmiHost,rmiPort);
UserInterface obj = (UserInterface) reg.lookup(rmiStrings
[1]);
User u = obj.find(userId);
if (u == null) {
System.out.println("This user is not valid");
} else {
UnicastRemoteObject.exportObject(smsClient);
reg = LocateRegistry.getRegistry(rmiHost, rmiPort);
LoginLogoutInterface objs = (LoginLogoutInterface) reg
.lookup(rmiStrings[0]);
//getting error at the following line.
String response = objs.login(userId, password, smsClient);
System.out.println("response :" + response);
} catch (AccessException ae) {
System.out.println(ae);
} catch (NotBoundException nbe) {
System.out.println(nbe);
} catch (RemoteException re) {
System.out.println(re);
} //end login()====================
Error is:
java.rmi.ServerException: RemoteException occurred in server thread; nested exception is:
java.rmi.UnmarshalException: error unmarshalling arguments; nested exception is:
java.lang.ClassNotFoundException: sms.rmi.graphics.StockMSClient_Stub (no security manager: RMI class loader disabled)================
I don't know why this is happening..Please help.
thanks & regards, js
Message was edited by:
jsitaraman -
How to implement a call back service?
hi all,
i have a method which calls a particular function module. i want to achieve the following two things in the code:
1. after calling the function module, i want the program flow to get paused - it should wait for a notification from the function module to proceed further.
2. the function module should send a call back to the method intimating that it is done with the job.
due to the scenario, synchronous call wil not solve the purpose. i need to use explicit wait and notificaion / call back service.
any help would be greatly appreciated. thank you.
rgds,
ramHello. Have you taken a look at CALL FUNCTION ... STARTING NEW TASK ...
See example below. Regards, Peter
DATA: INFO LIKE RFCSI,
Result of RFC_SYSTEM_INFO function
SEMAPHORE(1) VALUE SPACE, "For WAIT condition
MSG(80) VALUE SPACE. "Handling of exceptions
RET_SUBRC LIKE SY-SUBRC. "Handling of SUBRC
CALL FUNCTION 'RFC_SYSTEM_INFO'
STARTING NEW TASK 'INFO'
DESTINATION 'NONE'
PERFORMING RETURN_INFO ON END OF TASK
EXCEPTIONS
COMMUNICATION_FAILURE = 1 MESSAGE MSG
SYSTEM_FAILURE = 2 MESSAGE MSG.
IF SY-SUBRC = 0.
WRITE: 'Wait for reply'.
WAIT UNTIL SEMAPHORE = 'X'.
IF RET_SUBRC <> 0.
WRITE MSG.
ELSE.
WRITE: / 'Destination =', INFO-RFCDEST.
ENDIF.
ELSE.
WRITE MSG.
ENDIF.
FORM RETURN_INFO USING TASKNAME.
RECEIVE RESULTS FROM FUNCTION 'RFC_SYSTEM_INFO'
IMPORTING RFCSI_EXPORT = INFO
EXCEPTIONS
COMMUNICATION_FAILURE = 1 MESSAGE MSG
SYSTEM_FAILURE = 2 MESSAGE MSG.
RET_SUBRC = SY-SUBRC. "Set RET_SUBRC
SEMAPHORE = 'X'. "Reset semaphore
ENDFORM. -
Exception thrown while calling back a DSC componentcom/adobe/edc/policy/APSDocumentServicesManagerHo
Hi,
on starting LC 8.2 Server I get this error,
2009-04-02 09:40:00,031 ERROR [STDERR] 02.04.2009 09:40:00 com.adobe.idp.scheduler.callback.ServiceCallbackHandler execute
SCHWERWIEGEND: Exception thrown while calling back a DSC componentcom/adobe/edc/policy/APSDocumentServicesManagerHome
any ideas what went wrong?
regards
JohannesAs am I,
I manually installed LC ES2 into a new JBoss/mySQL instance following the manual install instructions here:
http://help.adobe.com/en_US/livecycle/9.0/prepareinstallsingle.pdf
http://help.adobe.com/en_US/livecycle/9.0/install_jboss.pdf
Then, applied the SP1, now I get this exception every ten minutes on the dot.
2010-09-24 00:00:00,038 ERROR [STDERR] 24/09/2010 00:00:00 com.adobe.idp.scheduler.callback.ServiceCallbackHandler execute
SEVERE: Exception thrown while calling back a DSC componentcom.adobe.edc.common.EDCException
2010-09-24 00:00:00,076 INFO [org.quartz.core.JobRunShell] Job APS_PRINCIPALKEY_REKEY_JOB_GRP.APS_PRINCIPALKEY_REKEY_JOB threw a JobExecutionException:
org.quartz.JobExecutionException: java.lang.Exception: ALC-DSC-003-000: com.adobe.idp.dsc.DSCInvocationException: Invocation error. [See nested exception: java.lang.Exception: ALC-DSC-003-000: com.adobe.idp.dsc.DSCInvocationException: Invocation error.]
at com.adobe.idp.scheduler.callback.ServiceCallbackHandler.execute(ServiceCallbackHandler.ja va:102)
at org.quartz.core.JobRunShell.run(JobRunShell.java:202)
at org.quartz.simpl.SimpleThreadPool$WorkerThread.run(SimpleThreadPool.java:529)
Caused by: java.lang.Exception: ALC-DSC-003-000: com.adobe.idp.dsc.DSCInvocationException: Invocation error.
at com.adobe.idp.scheduler.callback.ServiceCallbackHandler.execute(ServiceCallbackHandler.ja va:101)
... 2 more
Any suggestions on how to check the callback schedule for the misbehaving callback ?
Jason.
Maybe you are looking for
-
I plan to give my ipad to a friend who does not have an Apple computer once I have cleared my personal information. Will he be able to set it up without iTunes?
-
Webservice Exception from Webdynpro
Hi, We are on 7.1 SP04 Patch 1. We have created a webservice with http and None Authentication and deployed on EP 7.0 server. We have set a constant User Name and Password in Visual Admin. We are able to execute this webservice successfully from Webs
-
What do I need to do to connect to a remote windows server?
I was able to connect my G4 10.2 to the work server and have all the details (IP address, domain name and my own login and password.) Since buying this G5 I am unable to connect. I have read SO many posts on the subject and have tried some things. Un
-
How Can i Create my own sounds in Garageband?
I know how to take songs and create them into ringtones for my iphone but i would like to know how i can create a simple sounding text messaging notifier from garageband. Anyone have any ideas?
-
Good One - "ORA-00308: cannot open archived log", No Recovery Going On
Folks, Oracle 11gR1 SE cluister in archive log mode. Every hour I scp old logs over to a different server and nuke the ones so archived. I always switch the log destination to a new directory before moving and nuking, so I'm not touching logs being w