Call failed due to network issues

call failed due to network issues lync 2010 client. even when i'm trying to do a test call from my system, same error comes.

Please, share more details on error from logs. Also check firewall ports.
The Media Relay Authentication Service (MRAS) is responsible for notifying the Lync client of the STUN and TURN IP address for ICE. This service
run on UDP port 3478.
To check that the UDP port is open on the firewall between the Internal Lync clients and the Edge server running this service you can use the Microsoft tool PortQry
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Similar Messages

Lync server call failed due to network issues

hi,
i receive an error while making a lync call to an internal user
"call failed due to network issues"
i have two ip's installed on My NIC but when i remove one ip of the ip's from
my nic, everything seems to work fine.
Kindly help

Hello Matt,
Hope you keeping well..!!
We are communicating with external customers lync server through federation option setup on our corporate lync server. We have received the federation setting from the customer with SIP address which has been setup on our corporate lync servers after
that we were able to browse the customer contact through corporate lync account.
We were also able to chat with external customer but however voice/video functionality are not working through same session. Whenever we try to dial out external customer lync account it ended with error message "call ended due to network issue".
We have checked the setting from corporate lync servers and network point of view but doesn't find any issue which cause the disconnection to voice/video over lync. Could you pl help or guide with the way.
Thanks

Call Failed due to FADING ??

Hi, I'm hoping someone out there can help me!
I sent my Torch 9810 in to Rogers for repair (phone was overheating). Today they sent me a new replacement, because they couldn't fix the old one....but now the new one can't send or receive calls.
I keep getting the error message "Call Failed due to Fading". Is this a network or a hardware problem?
Rogers said it was the network and tech support said it could be the hardward....any suggestions?
thanx

Hey myrad,
Sorry for the delay in replying.
So if you're using EDGE/GPRS (2G) the phone calls are working perfectly. It sounds to me you have a radio issue now but to make sure it is a radio issue, check the following:
1. Are you using the most up to date device software from www.blackberry.com/update or from Rogers?
2. If not, I suggest updating and then try to reproduce the issue.
3. If you are running the latest software then I suggest contacting Rogers to get a replacement since it is a radio issue.
Let me know if you have any more questions.
Cheers.
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

Sharing ended due to network issues

I have a strange issue with one Lync 2010 user in that she is not able to stay in a desktop or app sharing session for more than 2-3 minutes. Without fail, after a couple minutes she will get kicked out of the session with the error "Sharing
ended due to network issues". She can then rejoin the session, but will get dropped again a couple minutes later. None of our other users seem to have this issue.
I've read other posts on the error, and most seem to involve Edge server configuration. However this sharing is happening only internally, so there is no Edge server involved. I've also read that Citrix Edgesight can cause this, but we don't
have the agent deployed.
I've looked at her client logs, and I see a lot of these types of errors around the time of the issue:
SIP_URL::ParseUrlParams invalid char M found when trying to parse params
SIP_URL::ParseUrlBase ParseSipUrlParams failed 80004005
I'm not sure that these errors are directly related to the problem though.
Any suggestions would be appreciated.

Hi,
Did the issued Lync user use the same type of SIP name with others?
Please try to change the type of the issued user’s Lync account such as user’s email address or specify a sip uri to have a try.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Photo upload to iCloud fails with the error message 'Upload failed due to network error'. Ideas?

I am trying to get my photos on my Mac Mini onto my iPad 2 via iCloud. I have tracked the problem down to upload failure from Mini to iCloud. 1St (&every) photo upload fails with the message 'Upload failed due to network error'. Any ideas?

I doubt this issue is related to the Mac Mini specifically.
I have 44 photos shot with an iPhone 3G that will not upload to iCloud Photo Library. I try and drag-and-drop them onto the web interface and I get the same error message you did:
Upload Failed
44 items were not uploaded due to a network error.
However, I have another 62 photos shot with the same iPhone 3G that upload without issue. And I just uploaded 440 photos from an iPhone 4 without issue.
I thought it may have something to do with certain EXIF tags missing on the photos that would not upload but I have not been able to figure out a pattern when comparing photos that work and photos that don't work.
The photos that won't upload open fine in QuickLook, Preview, and Pixelmator so I doubt the image is corrupted in some way.
I can AirDrop the photo to my iOS device and it will upload to iCloud Photo Library, the photo/video count will be incremented on the iOS device and iCloud Photo Library but the photo will never be displayed in iCloud Photo Library. When I delete the photo on the iOS device the photo/video count will decrement on the iOS device but will remain the same in iCloud Photo Library. When this occurred the following error was thrown in the iCloud Photo Library web interface:
Expanding Details shows the following log:
https://gist.github.com/jameswthorne/757e319b9fee63119890

Get Publish failed due to network error on Publish

Everytime I make a change to my web site within iWeb then do a Publish I get a message "Publish failed due to network error. Check your internet connection and try again".
Although I get the above message my changes do get made on my web site.
I am on high speed internet. I have received this message every time I do a Publish after making changes for the last several days.
http://web.mac.com/johnnelsonhomes is web site address. Again, changes are getting posted most times, although not always.
Any ideas?
Thanks in advance.

I have been having the same problem. I can access my iDisk, but cannot publish to it. When I try i get a 'cannot publish due to network error' message. I can successfully upload the same website to my 'GoDaddy' hosting acct. This is what I have done so far without success:
Turned off all commenting and searches and .mac specific services.
Tried connecting directly to my DSL modem to try to eliminate any problem that may be introduced by my router or firewall settings.
Reformatted my hard drive and re-installed OSX (clean). Patched the new system with all available updates. I did not restore from my back-ups to ensure that any corrupted settings would not be brought forward to the new install. I then created a simple one page site with iweb and attempted to publish to .mac. Even this failed. I am not sure what I could be missing. I had been publishing for months without any problem. Then I started getting this problem occasionally, and now I get it all the time. The only thing I can think of is if there is possibly a network latency problem causing the connection to time out.

RMAN restore fails due to space issue

Hi,
My database size is 225 GB . I m restoring the backupfiles using RMAN from production backup to the test instance.During restore process rman failed due to space issue.When the error occurred rman restored around 122 GB.
Now i increased the free space in server.So now my doubt is i have to delete the restored files (122GB) and start the restore process again or RMAN will automatically skip the the restored file and resume the process from where it was failed ?
DB Version -11.2.0.2
RMAN error
channel CH2: ORA-19870: error while restoring backup piece /ebs/DEV/backup/GOLD_db_t801111628_s10788_p1.rman
ORA-19502: write error on file "/ebs/DEV/bin/db/apps_st/data/a_txn_data11.dbf", block number 3492608 (block size=8192)
ORA-27072: File I/O error
Linux-x86_64 Error: 28: No space left on device
Additional information: 4
Additional information: 3492608
Additional information: -1
Thanks

When you start the restore from the failure, RMAN knows whcih are restored and it will check file headers. if the headers match, it will skip restoring the files.
Hope this helps,
Regards,
http://www.oracleracexpert.com
RMAN Debug and Trace
http://www.oracleracexpert.com/2012/11/rman-debug-and-trace.html
Time for Change: Migrate your Non-RAC Database to RAC
http://www.oracleracexpert.com/2012/10/time-for-change-migrate-your-non-rac.html

"Publish Error: Publish failed due to network error. Check your internet co

I am using the very latest version of iWeb. I have had it for a week.
First let me tell you the message that I got and then what I was doing prior to getting the message:
It said: "Publish Error. Publish failed due to a network error. Check your internet connections and try again."
I did check my internet connections and I called mt cable modem ISP. He put me through some tests and ascertained that the problem was not with the cable connection. I can connect to the web (of course) and I can send and receive email. The fellow at the ISP (Road Runner) told me that the uploading goes just fine but that the confirmation end of it is bad.
I have made 9 pages for my website. I clicked the button to publish the 10th page and got the message at the top of this post.
Then I called Apple Care and took advantage of the 90-day help warranty. The gal there had me try to publish to my private folder. That worked! I was able to publish to the folder and that message at the top of this post did not appear. It said that the page was published and did I want to visit it.
I ended up deleting the page about my friend Lerma, since everything was going fine until I did that page. AS I recall, there was a mixup with the pages and I thought I had fixed it.
Then I worked a little more on my husband's Memorial Site and tried to publish and got the same bad message as above, meaning that it wasn't just the page about Lerma but any page I might be doing since doing her page.
NOW THIS IS THE ODD PART:
I went to the website on Safari browser with the intention of checking out the other earlier pages, only to discover (happily) that my husband's memorial page (the beginning of it) WAS THERE even though I got that message saying that there had been a network error. Lerma's page, however, was NOT there.
I am between happy knowing that a page can show up on the website even though I get a message saying that it did not, but anxious knowing that if I am getting Publish Error messages, something is screwy with the program.
I will continue to try to publish to the Internet, but meanwhile I welcome any observations and happy accounts of how they got the same message but everything ended up fine after a while.
Meanwhile I am going to be working on my pages even though right now I am getting those messages saying that they could not publish due to network error.
I need a break.
— Lorna in Southern California

Hi Lorna!
Sorry to hear that you're getting the dreaded
"Publish Error" message from iWeb. Lots of people
have reported getting this type of error...and I
don't think it ever really has much to do with the
network...at least nothing that can be fixed. The
fact that you have been publishing just fine up until
now is a good thing. Some people have NEVER been
able to publish to the web. Hopefully this problem
will clear itself up. Maybe it's just sunspots or
something. Probably someone thinks you need a break,
too.
Is this the kind of thing that would warrant me going back to the Apple Store to get an exchange???
— Lorna in Southern California

Call failed with airtel network

I was using Vodafone network, recently shifted to Airtel. My phone is unlocked and network is active. I am able to receive calls and use data over 3G. I am even able to receive calls. But I am not able to make any calls. Every time I try to call I get Call failed.
I visited Airtel office, they put sim in other phone and outgoing calls was working fine. But its not working in my iPhone.
I even tried resetting my network, still no help.
Please help

I had the same exact problem ,then I read in one of these discussions that the issue is with the caller id. though we cannot turn it ON or Off but somehow even checking the status of the caller ID did the trick and now I am able to make outgoing calls as well. My phone is iphone 4 with airtel( recently ported from vodafone).

Unable to back up due to network issues

does anyone else have a problem backing up by wifi to a airport time capsule "due to network errors"?

It is common on Mavericks.. and happens on other OS as well. The TC occasionally just disappears from the network as a resource.. strangely the internet still works.
A reboot of the TC is enough to generally fix it.
If not tell us more.. exact error messages.. and how the whole network is setup.

RFC call failing due to UNICODE implementation

Hi
We are trying to connect to a SAP system using the JCO (SAP-JAVA Connectivity). We are passing the user name as an input parameter and in turn the SAP system send back the no. of item (ABAP Type integer) pending for the user name to the java and its inserted/updated in Oracle DB (which does accept the unicode characters).
It was all wokring fine untill the SAP system has been migrated to Unicode upgrade. Now the RFC call is getting failed from our system. On analysis we found with debug, that the user name is not getting accepted by the SAP system and throwing the error -says Exception in thread "main" com.sap.aii.proxy.framework.core.BaseProxyException: Conversion error between two character sets., error key: RFC_ERROR_SYSTEM_FAILURE and at the SAP end the error says "Conversion of "UNAME" from code page 4103 to 4102 is failed". The unicode change in SAP system cannot be reverted back due to some constraints.
Can you please help, how can we pass the user name as encoded in character set 4102 or any other solution so that it can be accepted by SAP and run the Function module and return the data.
Many Thanks
Snehil Joshi

Check RFC destination in Tx SM59. You must have one tab for unicode settings.
Regards.

CCMS: CEN configuration - Registration Failed due to RFC : Issue Resolved.

Hi There!
I was trying for CEN-CCMS setup and I was bale to connect my other systems to the CEN, infact I was able to connect all the system, but somehow my DEV box is detached from the CEN box. When I try to run sapccmsr -R -j2ee pf= to register with CEN, at the end of when I enter the details of "csmreg" user of CEN, throws the following error.
INFO: Updated saprfc.ini in agent work directory /usr/sap/ccms/DEV_02/sapccmsr
ERROR: Registration failed: Can't get version of DEV. RfcRc = 2, C_CALL_FAILED
RFC Error Info for SALS_MS_GET_LOCAL_MS_INFO
message:
status: EXCEPTION C_CALL_FAILED RAISED
intstat:
INFO: dsr: dsrlib unloaded.
EXITING with code 1
Illegal instruction (core dumped}
In SM59, the TCP/IP rfc name with those program ID throws error. "Error when opening RFC connection". If I creadted the Program-ID in VA, then SM59 will pass the test connection, but its not the resolution, the DEV box is still detached from CEN.
I redo the configuration with new CSMCONF too
If I check the "monitored Remote System/RZ21 on CEN, it throws:
> Connection test to destination DEV_CCMS_COLLECT terminated with ERRORS
> Error when calling the underlying C function (function 'SALS_MS_GET_L..
I followed the SAP's monitoring guide for NW04s-SP-13
PI-7.0, SP-14
Thanks anyways
vipin
Issue Resolved.
Edited by: Vipin Sagar on Jul 22, 2008 4:08 AM

Hi All,
can any one share the solution for the above error.
I am getting the same error for one of the systems. other systems are working fine.
Thanks and regards,
Sunny

3G video call and wifi open network issues

I have bought Lumia 920 few days back. I'm facing some issue with WiFi.when I'm connecting with WiFi open network, connection getting connected but web page is not opening, but in my previous Samsung mobile is getting connected and working ok. I don't know why Lumia 920 only making trouble and also one more thing there no 3G or 4G video calling option in the mobile. So could you please help me regarding this issues.

Are you having problems connecting to all wifi's or just this one? If just this one, you could try updating the router fimware.
Your Lumia supports video calling using Skype.

Project Server Cumulative Update August 2013 install failed due to login issue/interruption

Hi all,
I was in the process of running the installer (exe) for the August 2013 Cumulative update "uber" hotfix for SharePoint 2013 and Project Server today (KB2817615) on three servers. I was connected to the servers via Remote Desktop, logged in as the
Farm account.
On one of the servers, somewhere during the installation, my Remote Desktop session got "hijacked" by another user who was not aware of the ongoing process..so he was logged in as the Farm account for a few minutes.
I logged back in and found that the install dialog was gone...apparently the install stopped due to the interruption in logins. So I attempted to re-run the hotfix installer, but it now says "There are no products affected by this package installed
on this system."
I've tried clearing the timer cache and running the installer using "PACKAGE.BYPASS.DETECTION.CHECK=1" but neither has worked.
Any ideas on how this can be fixed or re-run?
Thank you for your assistance!
Regards,
Kevin Worthington

Hi Kevin,
Were you able to resolve this issue. I didn't have any interruptions or login issue, the installation cancelled itself!
Any help will be highly appreciated.
Thanks
SJ

Siri has not worked all day due to network issues?

Siri response all day has been "I'm having trouble connecting to the network.

You posted in the iPad forum instead of the iPhone forum. To get answers to your question, next time post in the proper forum. See https://discussions.apple.com/index.jspa I'll request that Apple relocate your post.
 Cheers, Tom

Call failed due to network issues

Similar Messages

Maybe you are looking for