Call FM destination often disconnected after calling failed

Dears,
when i call RFC registered in .net with sap connector, it is often disconnected auto. after calling failed.
then we should re-start RFC server in .NET, and the connection (RFC destination)will be ok then
what tools could i use to trace these and any advice ?
BR

Hi,
when i execute RFC with empty table parameters, it is ok.
But it give error 'data not received' when set some data in the table parameter and then the connection is shutdown.
ths for your tool .

Similar Messages

Free jabber disconnect after call for 10-20 sec

I try to use Free Jabber call to my system via DNS SRV record. It can connect to system but It will disconnect after call for 10-20 sec.
All case which call via DNS SRV record, I checked and found
-The problem happen only call to TPS (via conductor).
-If call to endpoint, It's working fine.
-If call to MCU (registered with VCS), It's working fine.
I see log files which new INVITE is sent by TPS to VSC-Exp, VCS-Exp tries to send it out and then TCP connection fails.
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,239" Module="network.tcp" Level="ERROR": Src-ip="172.18.7.8" Src-port="25297" Dst-ip="199.19.190.28" Dst-port="5060" Detail="TCP Connection Failed"
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,240" Module="network.sip" Level="DEBUG": Action="Sent" Local-ip="172.18.8.8" Local-port="7001" Dst-ip="172.18.8.20" Dst-port="25008" Msg-Hash="5130918937689017019"
SIPMSG:
|SIP/2.0 408 Request Timeout

I try to use Free Jabber call to my system via DNS SRV record. It can connect to system but It will disconnect after call for 10-20 sec.
All case which call via DNS SRV record, I checked and found
-The problem happen only call to TPS (via conductor).
-If call to endpoint, It's working fine.
-If call to MCU (registered with VCS), It's working fine.
I see log files which new INVITE is sent by TPS to VSC-Exp, VCS-Exp tries to send it out and then TCP connection fails.
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,239" Module="network.tcp" Level="ERROR": Src-ip="172.18.7.8" Src-port="25297" Dst-ip="199.19.190.28" Dst-port="5060" Detail="TCP Connection Failed"
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,240" Module="network.sip" Level="DEBUG": Action="Sent" Local-ip="172.18.8.8" Local-port="7001" Dst-ip="172.18.8.20" Dst-port="25008" Msg-Hash="5130918937689017019"
SIPMSG:
|SIP/2.0 408 Request Timeout

Outbound call doesn't disconnect after call end

Have you ever seen something like it:
I make a call from my ip phone (3911 or 6921) to an external phone (ex: cell phone: 084645727) and the call works fine, but when cell phone turned off the call, on my ip phone the call still connected, ip phone show me on display that the call still active, the call is just disconnect when I put the phone onhook.
I use CUCMBE: 7.1.3(SU2)
Cisco 2821 : c2800nm-spservicesk9-mz.124-20.T4.bin
debug vpm signal
BHEGV1#R2 Got Event R2_ALERTING
*Nov 25 07:42:36: show voice call status
CallID     CID ccVdb      Port             DSP/Ch Called #   Codec    Dial-peers
0xD8803    20E8 0x48177B78 0/1/0:0.3        0/1:1 *2125463737 g711ulaw 7500/40
0xD8847    1C9D 0x48177B78 0/1/0:0.1        0/1:3   7434       g711ulaw 1/7500
0xD88B2    26E8 0x48177B78 0/1/0:0.28       0/1:5 *087068998 g711ulaw 7500/30
0xD88B6    27E8 0x48177B78 0/1/0:0.27       0/1:2 *084645727 g711ulaw 7500/30 (it is my call)
0xD88BD    1D22 0x48177B78 0/1/0:0.2        0/1:4   7491       None      1/7500
0xD88C0    28E8 0x48177B78 0/1/0:0.22       0/1:6 *084743874 g711ulaw 7500/30
After cell phone turned off the call, the debug vpm signal just show me it:
*Nov 25 07:42:50: htsp_process_event: [0/1/0:0(27), R2_Q421_OG_ANSWER, E_DSP_SIG_1100]
Does anybody could help me !
Regards.

Hi All
I had this issue with Oi and EBT, not sure if this is the same, but i had an issue where the Voice channel in clearfwd - I was facing the Bug CSCtd74470, there a workaround but the upgrade of the GW to Version 15 works properly, the output of the "sh vo po sum | include clearfwd" will confirm if this is your case.
Also in others situations I solved my issue applying the command timeouts call-disconect 3, under E1 Port
Please rate this post
Cheers
Bruno Rangel
"Se você quiser alguém em quem confiar, confie em si mesmo. Quem acredita sempre alcança"
Renato Russo

Call Forwarding Icon Stays On After Call Forwarding Turned Off

I have the problem described here: http://forums.precentral.net/palm-pre-pre-plus/271878-help-me-diagnose-glitch-call-forwarding-webos-... .
I see the problem on my unlocked GSM Pre2 with AT&T, and it goes away when I put my sim card in my old Treo 680. The calls stopped actually forwarding when I turned off call forwarding on the Pre2. However, the call forwarding icon comes back on the Pre 2, and even shows when I move the sim to my Treo. It turned out that reading the call preferences from the Treo was enough to reset the icons for both phones, and the icon stayed off until the next time I forwarded calls. Maybe the Pre2 was failing to update something on the SIM to match the status on the network, but the Treo got it right?
Anyway, I don't want to be swapping my sim card around every time I forward calls, and I can't count on my Treo to last forever either.
Any better ideas?
Post relates to: Pre 2 p102una (Unlocked NA)

Have you tried contacting 3 to see if your account is setup correctly or if you need a new SIM?
You can try testing with another SIM or restoring the iPhone.

Call is getting disconnect after 3 min when the caller is in queue

Hi,
I am using icm 7.0 with ip ivr 7.0. when all the agents are busy and caller is in queue,call is automatically getting disconnected after 3 min with the message " We are experiancing system problem and unable to process the call. please try again later" .
Icm and ivr script are attached
Regards,
Dinesh Joshi

Hi Chrish,
you are right. the timer was for 180 sec only. now things are working fine after increasing the timer.
Thanks a lot for your reply.
Regards,
Dinesh Joshi

HT204368 My bluetooth is paired with phone. After a call, it seems to disconnect so that it is no longer paired on a subsequent call.

Looking to remedy recurring problem. Bluetooth seems to unpair/disconnect after call to iphone. Has to be shut off and on to re -pair. help!

Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
Thanks again!

When talking on my phone it is disconnecting the call, by itself, after a few minutes.

I talk breifly on my phone and it is hanging up or disconnecting the call. I am not touching anything and have plenty of bars for service? Whats going on?

Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Call is disconnected after being transferred by the AA SPA 400

I have 2 groups set up in the AA to transfer to different groups ie "Accounts" or "Production". These all worked originally, but now they seem to have stopped working. Callers dial in and press "13" as per the prompts, then the AA message tells them to wait while the call is transferred, and then the call is disconnected.
This only happens for one of the prompts, the other one is fine. As i said this all worked fine originall, and no settings have been changed.....
Any ideas / help / suggestions greatly appreciated.
System is SPA9000, SPA400, SPA942 x 3

After having searched through this and a number of other forums I am amazed that no one has come across and understands the true reason this is happening. The other posts do offer some insight and good suggestions but no one has realized the true underlying problem. Apparently the AA, no mater what dial plan you use, will forward any partially dialed portion of the numbers that match the list. So even if you specifically limit the acceptable numbers to only the extensions on your system you can still get a partial result passed on from the AA which does not have a valid extension on your system.
For Example:
DP1 = (120|102|103|152|100|9|<0:100>|<*8:vmm4>)
AA Script 1 =
<aa>
<form id="dt" type="menu"><audio src="prompt5" bargein="T"/><noinput timeout="5" repeat="T"/><dialplan src="dp1"/>
<nomatch repeat="F"><audio src="prompt3" bargein="T"/></nomatch>
<match><case input="9"><audio src="prompt8" bargein="F"/></case>
<default><audio src="prompt2"/><xfer name="ext" target="$input"/></default>
</match>
</form>
</aa>
You would think this would be sufficient to limit inbound calls to just the extensions listed in the dial plan. Not so. The caller can dial any part of the listed extensions (1,10,12,15,*...) and the call will still be transferred and subsequently dropped. I tried every possible combination of dial plan settings including specifically rejecting (which you should not have to do) everything other then the desired combinations. Problem is if you try to reject any subset of the valid combinations it interferes with them and they get rejected to. The real problem here is in that how the dial plan is being processed allows these invalid partial number through. Believe it or not this happens more then you think. For whatever reason a digit is not heard or does not get registered will cause this to happen. Adjusting the DTMF settings does improve things in most cases but does not solve the issue. Problem is that any number passed on by the AA that does not translate to a valid destination will get dropped.
After much trial and tribulation I have come up with a way using the AA script to eliminate any and all none desired digit combinations to prevent anything from getting transferred by the AA that will get dropped. It is a work around but it is effective and reliable. Solution is simple. Use the AA script to take specific action on only the desired responses. Everything else goes to the default which could play an "invalid..." message or other action. Here's how it looks:
DP1 = (0S0|*8S0|xxxS0)
AA Script 1 =
<aa>
<form id="aadpw" type="menu"><audio src="prompt5" bargein="T"/><noinput timeout="5" repeat="T"/><dialplan src="dp1"/>
<nomatch repeat="F"><audio src="prompt3" bargein="T"/></nomatch>
<match>
<case input="*8"><audio src="prompt2"/><xfer name="ext" target="vmm4"/></case>
<case input="0"><audio src="prompt2"/><xfer name="ext" target="100"/></case>
<case input="100"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
<case input="102"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
<case input="103"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
<case input="120"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
<case input="152"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
<default><audio src="prompt3" bargein="T"/></default>
</match>
</form>
</aa>
It is a little like using a sledge hammer to pound in a tack but it works. It's the only thing I was able to come up with that does. Oh, and by the way you may notice the case for "*8". This allows transfer from and outside line to the voice mail manager ("vmm4") on line 4. You can modify the dial plan and AA script for any sequence you want. The case for "0" is there to allow outside callers to press "0" and get transferred to whatever valid extension or hunt group you wish to designate.
Hope this offers a little more insight into what was really happening. Let me know if anyone comes up with a better way to do this.

Why does my phone disconnect after 4 hours of call time

why does my phone disconnect after 4 hours of call time? Is there anyway I can change this?

You mean that you're on a single call for 4 hours continously, and then it disconnects?
If so, contact your wireless carrier. That's a cellular connection issue.

I´ve just changed my apple id password, and when trying to use Facetime, after having entered such new password, it won´t fullfill the calls, nor can I receive incoming calls, it simply gets disconnected. What do I do??

I´ve just changed my apple id password, and when trying to use Facetime, after having entered such new password, it won´t fullfill the calls, nor can I receive incoming calls, it simply gets disconnected. What do I do??

iOS: Troubleshooting FaceTime
Unable to make or receive FaceTime calls after April 16, 2014
Using FaceTime and iMessage behind a firewall
iOS: Troubleshooting FaceTime and iMessage activation
iOS: Using FaceTime
FaceTime, Game Center, Messages: Troubleshooting sign in issues

[svn:fx-3.x] 7197: Bug: BLZ-354 - Client still polling after calling ChannelSet.logout() when subscribed to messaging destination.

Revision: 7197
Author:   [email protected]
Date:     2009-05-21 14:49:44 -0700 (Thu, 21 May 2009)
Log Message:
Bug: BLZ-354 - Client still polling after calling ChannelSet.logout() when subscribed to messaging destination.
QA: Yes
Doc: No
Checkintests: Pass
Details: In polling channels, stop polling as soon as logout ack is received.
Ticket Links:
    http://bugs.adobe.com/jira/browse/BLZ-354
Modified Paths:
    flex/sdk/branches/3.x/frameworks/projects/rpc/src/mx/messaging/ChannelSet.as

Any advice would be helpful. Thanks

Why does my Sennheiser BW 900 headset disconnect after each call?

Although I had no problem pairing a Sennheiser BW 900 headset with my iPhone 4S, it disconnects after each call. It is the only bluetooth device paired to the phone. Any help with solving this problem would be greatly appreciated.

Still having same issue, only now it seems to stay connected at times and disconnect at times. My phone is literally right next to me, I am at my desk, not moving around. The strangest thing is that it REconnects again randomly. So I never know whether to answer with the headphones or using my actual phone! Please help!

Slide to unlock after a failed call

When I have a call that fails for some reason and the phone is “locked” it returns to the locked state, with a “call failure” message. All fine.
However, when I later “slide to unlock” the phone (usually after I’ve finished my journey) the iPhone always immediately calls the failed caller back.
I think there is a similar effect with missed calls.
I find this automatic calling without a prompt very irritating. Is there some way to disable this?
Thanks for any info...

First, try to reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose data by resetting.
If this does not work, try to set it up as new device, explained here:
How to erase your iOS device and then set it up as a new device or restore it from backups
If still no luck, get it checke by Apple:
iPhone - Contact Support - Apple Support

Why I get disconnected while calling after 3 minutes?

Why I get disconnected while calling after 3 minutes?

I wish I could put 1 more quarter and solve the problem. And yes, it happens in every call that goes beyond 3 minutes, local or international. To make it worst, I bought an iPhone 4 for my wife and has exactly the same issue, we are both from the Philippines. Thinking that they might be selling us over here the over runs or defective gadgets to my surprise my sister in law who lives in Texas is experiencing the same issue. I was looking in the apple store for support and found out that there is a batch of iphones that came out with that issue and that needs some kind of fix. The problem is that apple endoreses you to your network provider and here our network provider does not know what to do.. Have you heard of this fix? Kindly advice

My incoming calls on my iphone 5C get disconnected after the first ring. Please help!

My incoming calls on my iphone 5C get disconnected after the first ring. Please help!

I had this problem too with my newly bought iPhone 4s.I went to a technician shop to ask what the problem is and they said they could fix it however they would charge £35 and I believed this was too much. I was playing around with my iPhone to see if I could fix this problem I went on setting the clicked on the music section at the music section there is the button called sound check which was off so I decided to turn it on . After I turned it on my sound came back I was ecstatic I saved myself £35 and having to return the phone.

Call FM destination often disconnected after calling failed

Similar Messages

Maybe you are looking for