Call forwarded Caller ID

Hi Folks,
I have an issue in a new Voip deployment whereby when a user call forwards their internal phone to an external mobile, the site prefix is being added to the Originating caller ID on the destination mobile phone and trailing digits are stripped.
For example..
the site prefix is +43166105
A user outside the company with mobile phone number 06991968XXXX calls an internal extension that is call forwarded to 0664545XXXX, when the call rings on 06664545XXX, the caller ID is shown as +431661056991968, with last 4 digits missing
The site has two voice gateways, GW2 for specific mobile phone calls, and GW1 for regular calls and all other mobile calls, when a user call forwards to a mobile phone that is reachable via GW2, the caller ID is showing correctly (both g/w are connected to different providers)
I have a translation pattern on both g/w that strips the leading zero's of the calling number and also makes sure call type is presented properly to the provider.
Generally, i would be calling the provider, however the site are telling me that this worked OK on the previous PBX based setup.
Here are some relevant pieces of configuration information, and the ISDN debug of an affected call, as you can see, we are providing the correct digits to the provider, yet we always see the prefix regardless
I have tried changing the numbering type in the translation pattern from any to unknown and it has the effect of then showing no digits of the Caller ID, it will just show the prefix number.
508090: Mar 28 10:42:47.084 CET+1: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x07CC
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Calling Party Number i = 0x0181, '6991968XXXX'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '0664545XXXX'
Plan:ISDN, Type:Unknown
GW1
trunk group A1_Telekom
carrier-id Vienna_A1_Telekom
description Vienna_PSTN_Trunks
hunt-scheme round-robin both
isdn supp-service tbct notify-on-clear
translation-profile outgoing OUTBOUND
voice translation-rule 4
rule 1 /^01$.*$/ /01\1/
rule 2 /^0/ //
rule 3 /^8912$/ /0017275788912/
voice translation-rule 5
rule 1 /\+43166105/ /166105/ type any national
rule 2 /^000$.*$/ /\1/ type any international
rule 3 /^00$.*$/ /\1/ type any national
voice translation-profile OUTBOUND
translate calling 5
translate called 4
dial-peer voice 99 pots
trunkgroup A1_Telekom
service session
destination-pattern 0T
fax rate disable
direct-inward-dial
forward-digits all

Hi Steven.
Can you please activate a debug ccapi inout on your VG1 and make a call?
After that please attach the output here.
Thanks
Regards
Carlo

Similar Messages

CUPC 8.6 call forward to voicemail

Hi!
I am using Cisco Personal Communicator (CUPC) 8.6 and also CUCM 8.6. I have CUPC in Deskphone mode, connected to a 6945 IP Phone. I also have Unity Connection where my voicemail box is hosted. When I want to setup call forward to voicemail button in cupc option, it is not working. CUPC will not handle the options I setup seconds before. If I manually put in a call forward to extension number of voice mail pilot call forwarding is working. also call forwarding to my mobile is working.
I checked End User settings, IP Phone is associated to my user, also CTI controll is enabled on device and line settings. user privileges are correct. I tried it on jabber client where it works fine. I also restarted CTI and Callmanager Services on the Servers.
Does anyone has an Idea if this is a general bug in CUPC or does anyone can tell me what the problem might be?
Thanks!
René

Hi,
If at least one of these phones is set to CF to VM then it will, if not, then no.
If none of your phones is set to CF to VM CUCM will not send them to VM, that is expected, if you need to ring, phone A, and if it is not answered to go to phone B, C... and so on, and send the caller to VM after you have reached all of these then use a hunt group, (the pilot can be set to CF to VM if nobody answers), if you need to ring all phones at the same time so someone can pick this up, use a hunt group with a broadcast logic.
If this is for a single user, check 'single number reach' (SNR) or mobility on CUCM.
Bottom line, there is no way to send a caller to VM if none of the phones is set to CF to VM.
HTH
Chris.

How to delete the number saved in CALL FORWARDING list?

how to delete the number saved in CALL FORWARDING list? seems like the number cannot be deleted in CALL FORWARDING list, i tried several times...
he thing is, here are three numbers in the call forwarding list, one of them were set up by mistake, and none of them can be deleted.......it brothers me all the time. i already turn it off, but the number list is still there...

Hello dennis130915 and welcome to the BlackBerry Support Community Forums.
The image you have uploaded is unable to be displayed.
Call Forwarding is a carrier controlled feature. Most likely, the number you see could be for the Voice Mail server.
It's advised you call your mobile service provider to further assist with this feature.
Thanks!
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

HT201401 my earphones are not working on my iphone4 to play, stop or forward to other tracks or answering a call and i know its not the earphones as ive just paid out for a new pair at £27.99 and still wont work anybody got any advice as fed up honestly

anyone can you help my earphones are not working on my iphone4 and i know its not the earphones has just bought new pair and no joy I can not play, stop, forward to different tracks or anything cant answer call nothing end of ideas can anyone help pretty please

Yes there genuine apple earphones I have now blown down jack slot and silly enough I turned my phone off and now it's back on earphones working properly now feeling a wee but silly as such a simple thing got them working.
Thank you guys and I know where to come again if I need any further assistance.
Again thank you everyone

Call forwarding on iPhone4. I am sick of trying but once I input the number and go back to call forwarding, it turns off call forwarding. Any idea why

tried the simple way of call forwarding going in to settings>call forwarding> turn on call forwarding> enter number> return to call forwarding
but the status is going back to 'off' from 'on'
I also tried *61*number# but there again its failing. Can someone assist please?

Who is your carrier? Not all carriers support enabling and disabling call forwarding using the controls in Settings.

I am getting old and looking forward to use I Pad as a Phone if possible through WIFI! I this possible? The screen is to small for me! If possible, with new I Watch taking calls, other uses through I Pad!

Like I wrote on title, I am getting old and it is not easy to see E-mails, news etc. on a I phone! New I phone will not help me for the size.
If possible, everything without calls, I would like to use I Pad as direct unit, and for calls through I Pad over WIFI all calls. If a call as Skype, I would like
to use the I Pad as a monitor. Is this possible?
I found on a side that there is a product for people for better hearing, which can be put into the ears, using WIFI with I Phone.
If this product could be used also for I Pad as a Phone for hearing, and the I watch or I Pad as Microphone, it will be great for old Mac users.
Is this possible with our system know?
I am using Mac since Classic II! Would like to continue with the newest items with the possibility for old person with bad Eyes or Ears.
Looking forward for a kind answer
with regards
Christian an old Mac user!

Definitely No

Call forward feature not working on remote app on ipad

I can not activate called forwarding of my house phone from my ipad or iphone. The pop up box does not allow the ok to work.

Hi Josie,
Fios Digital Voice is our only phone service that allows you to manage call forwarding on your Fios app.
If you do in fact have Fios Digital Voice, then please try uninstalling and reinstalling your app and let us know if that works.
~Jess

Jabber for Windows 9.2.4 - Spinner freezes on "forward calls to"

On Jabber for Windows 9.2.4 when we activate "Forward calls to" - the forward is set on controlled phone, however the spinner freezes (see image) and won't clear until a different phone is selected for control. Setting "forward calls to" "none" does not clear the spinner.

Hi Mark,
this is known issue: 'CSCui37305 - After forwarded call, "Setting call forwarding..." does not disappear' and it is already resolved in 9.2.6.
Regards,
Nebojsa

Call forwarding on qsig

Hi I am having a problem with forwarding a phone to voice mail over leased line.I have 2 2600's each with qsig connection to pbx.when a phone is forwarded over the leased line from one end to the other it only works 50% of the time ie. when it doesn't work it seems the phone just rings out and never goes to voicemail.I have looked at q931 debugs and for a good and bad call both debugs look identical.Also when there is success I notice that more than 1 isdn channel is being brought up.For it to work it seems to need 4 channels which seems crazy.My signaling config is as follows.interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-qsig
isdn protocol-emulate network
isdn incoming-voice voice
isdn bchan-number-order ascending
fair-queue 64 256 0
no cdp enable
is there any tweeking I can do to rectify this situation or is there an inherant problem with the amount of channels being seen as busy by the pbx for a successful forwarding to voicemail?Another thing is that it works every time when calling the ddi number which is forwarded over leased line to voicemail.Any opinions appreciated thanks!

Hi thanks for taking a look. Here are the debugs you asked for.They aren't totally complete but the bit you want should be in there.
4w1d: Bearer Capability i = 0x8090A3
4w1d: Channel ID i = 0xA98381
4w1d: Calling Party Number i = 0x49, 0x80, '545', Plan:Private, Type:Subscriber(local)
4w1d: Called Party Number i = 0x80, '567', Plan:Unknown, Type:Unknown
4w1d: ISDN Se1/0:15: RX <- CALL_PROC pd = 8 callref = 0x8C54
4w1d: Channel ID i = 0xA98381
4w1d: ISDN Se1/0:15: RX <- ALERTING pd = 8 callref = 0x8C54
4w1d: Facility i = 0x9FAA068001008201008B0100A124020207B4020101301B8400A51706052B0C024E01300E8004313238380A01040403353637
4w1d: ISDN Se1/0:15: RX <- FACILITY pd = 8 callref = 0x8C54
4w1d: Facility i = 0x9FAA068001008201008B0100A124020207B506052B0C024E0130178004313131310A0105040C2A3230332A42452A35343623
4w1d: ISDN Se1/0:15: RX <- FACILITY pd = 8 callref = 0x8C54
4w1d: Facility i = 0x9FAA068001008201008B0102A137020207B6020113302E0A010330058003353436020101400504038090A3A108A006800431323334820102A4028100A607A0058003353637
4w2d: ISDN Se1/0:15: RX <- SETUP pd = 8 callref = 0x0025
4w2d: Bearer Capability i = 0x8090A3
4w2d: Channel ID i = 0xA98381
4w2d: Calling Party Number i = 0x49, 0x80, '545', Plan:Private, Type:Subscriber(local)
4w2d: Called Party Number i = 0x80, '567', Plan:Unknown, Type:Unknown
4w2d: ISDN Se1/0:15: TX -> CALL_PROC pd = 8 callref = 0x8025
4w2d: Channel ID i = 0xA98381
4w2d: ISDN Se1/0:15: TX -> ALERTING pd = 8 callref = 0x8025
4w2d: Facility i = 0x9FAA068001008201008B0100A124020207B4020101301B8400A51706052B0C024E01300E8004313238380A01040403353637
4w2d: Progress Ind i = 0x8188 - In-band info or appropriate now available
4w2d: ISDN Se1/0:15: TX -> FACILITY pd = 8 callref = 0x8025
4w2d: Facility i = 0x9FAA068001008201008B0100A124020207B506052B0C024E0130178004313131310A0105040C2A3230332A42452A35343623
4w2d: ISDN Se1/0:15: TX -> FACILITY pd = 8 callref = 0x8025
4w2d: Facility i = 0x9FAA068001008201008B0102A137020207B6020113302E0A010330058003353436020101400504038090A3A108A006800431323334820102A4028100A607A0058003353637
4w2d: ISDN Se1/0:15: RX <- FACILITY pd = 8 callref = 0x0025
4w2d: Facility i = 0x9FAA06800100820100A20B020207B630050201130500
4w2d: ISDN Se1/0:15: RX <- DISCONNECT pd = 8 callref = 0x0025
4w2d: Cause i = 0x8090 - Normal call clearing
4w2d: ISDN Se1/0:15: TX -> RELEASE pd = 8 callref = 0x8025
4w2d: ISDN Se1/0:15: RX <- RELEASE_COMP pd = 8 callref = 0x0025~

Weird call forwarding issue when phone off PBX is on call forward.

Hello - have (2) 3600 series routers connected to pbx's doing toll bypass, T1 on one side E1 on the other. All calls work ok and voice quaility is good however when a user on the PBX behind the E1 puts his phone on forward the call fails with a fast busy type of error (actually it rings once then fails) ISDN debugs yield:Cause i = 0x81E020 - Mandatory information element missing then the router disconnects the call.

The 'debug isdn q931' command, shows the call progress and the areas of problems. Sometimes the call fails due to a timer expiration. In the debug command output, the time period from when the call proceeding flows until the call fails, gives a guideline for the amount of time required to complete a call connection. The workaround is to wind out timers, which allow the call setup enough time to complete the connection.

Unity 4.0 - Call Forwarding and Voice Mail

Here is the situation:
We have a DN (5301) that is not associated with a Unity mailbox but is on a 7970 phone. This extension is an "on call" number that is always forwarded to a technicans phone (local 4 digit ext or cell phone).
When a person calls 5301 I want the voicemail of the final destination to answer.
For instance if I had 5301 forwarded to 2000 - I would want 2000's voicemail to answer.
Is there a way to set this up?
Thanks in advance.
Jeff

Hi Jeff,
Sadly this cannot be changed until Unity 5.x (the ability to choose "Last Redirecting Number" in not available in any other Unity version);
Here are the Unity 5.0 release notes;
Route Forwarded Calls by the First or Last Redirecting Number
Cisco Unity supports the option of routing calls based on either the first or last redirecting number when a call is forwarded to Cisco Unity.
Note the following:
This option requires Cisco Unity-CM TSP 8.1(2) or later.
This option is not supported by integrations through PIMG units.
This option can be changed through the Advanced Settings Tool (AST), which is available in Tools Depot.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/release/notes/501curelnotes.html#wp507371
Call Information Exchanged by the Phone System and Cisco Unity
The phone system and Cisco Unity exchange call information to manage calls and to make the integration features possible. With each call, the following call information is typically passed between the phone system and Cisco Unity:
â¢The extension of the called party.
â¢The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the phone system supports caller ID).
â¢The reason for the forward (the extension is busy, does not answer, or is set to forward all calls). There is also a reason code for Direct Calls.
Cisco Unified Communications Manager SCCP and SIP trunk integrations can also provide the following call information (the choice of first and last redirecting number is set in the Advanced Settings Tool, which is available in Tools Depot):
â¢Called number
â¢First redirecting number
â¢Last redirecting number
Note Cisco Unity can use either the first redirecting number or last redirecting number, depending on the setting in the Advanced Settings Tool, which is available in Tools Depot.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudg060.html#wp1040786
If this was just a one-up type of setup you can configure a Voicemail profile (in CCM) for 2000 and apply it to 5301 that will allow this type of Call Forward to 2000's mailbox. The fact that you need this for Multiple Tech's will not work. Is there any way the Techs could use a Shared Line? Then these solutions could be adapoted.
Or in Unity set up Alternate Extensions so that User A is an Alternate Extension for User B etc. Sharing a Cisco Unity Voice Mail Box between Two or More IP Phones
Configure Alternate Extensions
Open the Unity System Administrator web page.
Navigate to the subscriber's profile. Select Subscribers > Find and Select a Subscriber > Enter Subscriber Information then click Find and click the Subscriber's name for the subscriber that owns the primary phone (2000).
When the subscriber page comes up, select the Alternate Extensions option and click Add.
Enter the alternate extension number (in this case 5301) and click the Save icon.
From this good Unity doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_configuration_example09186a008015ceec.shtml#steps
Hope this helps!
Rob

CME, Call forward to CUE from CCM IP phone

I want to call forward the call from CCM IP phone to CME ephone's voicemail which setup in CUE. works okay between CME ephones. configured voice service as follows but no luck. what did I missing to implement?
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service h450.2
no supplementary-service h450.3
-CCM4.1.3, configured H225 trunk. leave uncheck the MTP on the trunk device
-gatekeeper to connect between CCM and CME
-CME3.3, h323 to gatekeeper and sip to CUE
-CUE2.1
Thanks in advance,

It works by restart the CME router and have a question the sip-ua output. I have two media streams but the 2nd shows "STREAM_IDLE". I think this is for g729 connected to CCM via h323 gk. Can I get an explanation why?
CME#sh sip-ua calls
SIP UAC CALL INFO
Call 1
SIP Call ID : [email protected]
State of the call : STATE_ACTIVE (7)
Substate of the call : SUBSTATE_NONE (0)
Calling Number : 4083132006
Called Number : 4211
Bit Flags : 0x101A0030 0x100000 0x500
CC Call ID : 95
Source IP Address (Sig ): 10.253.66.254
Destn SIP Req Addr:Port : 10.253.66.2:5060
Destn SIP Resp Addr:Port: 10.253.66.2:5060
Destination Name :
Number of Media Streams : 2
Number of Active Streams: 1
RTP Fork Object : 0x0
Media Stream 1
State of the stream : STREAM_ACTIVE
Stream Call ID : 95
Stream Type : voice-only (0)
Negotiated Codec : g711ulaw (160 bytes)
Codec Payload Type : 0
Negotiated Dtmf-relay : inband-voice
Dtmf-relay Payload Type : 0
Media Source IP Addr:Port: 10.253.66.254:16998
Media Dest IP Addr:Port : 10.253.66.2:16904
Orig Media Dest IP Addr:Port : 0.0.0.0:0
Media Stream 2
State of the stream : STREAM_IDLE
Stream Call ID : -1
Stream Type : voice+dtmf (1)
Negotiated Codec : No Codec (0 bytes)
Codec Payload Type : 255 (None)
Negotiated Dtmf-relay : inband-voice
Dtmf-relay Payload Type : 0
Media Source IP Addr:Port: 10.253.66.254:17120
Media Dest IP Addr:Port : 0.0.0.0:0
Orig Media Dest IP Addr:Port : 0.0.0.0:0
Number of SIP User Agent Client(UAC) calls: 1
SIP UAS CALL INFO
Number of SIP User Agent Server(UAS) calls: 0
CME#sh sccp connections
sess_id conn_id stype mode codec ripaddr rport sport
1 2 xcode sendrecv g711u 10.253.66.254 2000 16518
1 1 xcode sendrecv g729 10.253.66.254 2000 17620
Total number of active session(s) 1, and connection(s) 2

No Call Forward to Call Handler

Hi,
we have cucm 8.6 and cuc 8.6
inbound call from ITSP transferred to CUC call handler for opening greetings and by pressing '0' it transfers to operator.
i want to configure custom busy message when operator is busy with other calls.
i configured another call handler with number 1660 and forwarded the operator calls to the call handler if busy.
the busy message is playing when i dialed the number 1660 from any extension, but the calls not getting transferred when the operator is busy.
i tried with forward all calls to the callhandler and getting the message ' cannot be reachable'.
i configured busy message on opening greeting call handler itself, in the callhandler "greetings" section's "busy" option, it didn't work as the call already got transferred to cucm.so its not coming back to callhandler if the ext is busy.
please can anyone guide me to configure busy message for operator.

Hi Anas,
i tried as you said,
its transferring the call if extension is busy by skipping welcome greetings, it's not what i wanted.
i need if any inbound call comes from ITSP first the welcome message with IVR plays, if the caller press '0' then only it should transfer to operator, if the operator is busy then it should play "Operators Busy" message.

IP Phone call forward to Attendant Console - reach Attendant Console Voicemail

Hello,
I have an old Attendant Console based on CUCM7.1(5) with CUC 9.
Most of my user have voice mail box.
My issue is following: Users forward there phone to AC pilot point during lunch time or meetings.
When a call is then transfered to Attendant Console, if it is not answered, it is redirected to Unity connection and reach User Voice Mail box.
This is the good way of working for all users (to reach first redirect number mailbox), but my customer wants in the particular case of calls forwarded to standard, to reach standard voice mail box.
How can we achieve this?
If I setup a Translation Pattern on CUCM to translate a dummy number into attendant console Pilot Point number, and forward user to this dummy number, does Translation Pattern replace the first redirect number?
Thanks for your help.
Thibaut

It is likely that they are transferring a call to the operator on a line they are not logged into instead of the queue.
All calls should be routed through the queue in order to receive full CTI control of that call, I would suggest you create a speed dial with the DN of the CTI Route Point for the operators queue and then transfer the call to that instead of the operator directly, this way the call sits in the queue with any other callers.

Cisco Forward and Call return to Voicemail on CUCM 8.5 question

Hi,
I have a user A that requires the call forward when busy/no answer to another extension B. If extension B is busy/no answer, A wants call to be returned to his voicemail.
Unfortunately User B has also a call forward to another extension c, so call forward from A are forwarded to C when B is busy.
Is there any means to have the calls from A return to his voicemail when B is busy/no answer.
I would be grateful if someone can help or is it a system restrictions.

Hi
That's how it works by default.
Unity looks at the 'first redirecting' number, and uses that to allocate forwarded calls to a VM box.
So if User A forwards to User B, the first forwarding number is User A. It goes in User A's box.
That applies regardless of how many times it's forwarded, unless something happens to 'lose' the forwarding number info. That wouldn't usually happen on-system, more likely if a PRI or other trunk is traversed.
Aaron

Frozen display when call is forward to voicemail IOS 8

After upgrading my iPhone 5s to ios 8 and 8.0.2,I forward incoming calls to my voicemail with a double click on sleep button and when I unlock my device the screen has been frozen, so I have to lock/unlock my iPhone to fix this issue,can anyone help me?

Hi,
If at least one of these phones is set to CF to VM then it will, if not, then no.
If none of your phones is set to CF to VM CUCM will not send them to VM, that is expected, if you need to ring, phone A, and if it is not answered to go to phone B, C... and so on, and send the caller to VM after you have reached all of these then use a hunt group, (the pilot can be set to CF to VM if nobody answers), if you need to ring all phones at the same time so someone can pick this up, use a hunt group with a broadcast logic.
If this is for a single user, check 'single number reach' (SNR) or mobility on CUCM.
Bottom line, there is no way to send a caller to VM if none of the phones is set to CF to VM.
HTH
Chris.

Call forwarded Caller ID

Similar Messages

Maybe you are looking for