Call Hander cisco unity conection

Dear sir !
I have a case using call hander on Cisco unity conection
this is a case:
- Dial 1800 (IVR) --> the Welcome Messages
- After call Handler-> auto routing call to Operator (0)
I config dial IVR ok. After call handler the system tranfer to Operator, but the system message " we tranfer the call". I want to disable system message
Please help me
Thanks

Good Day,
In Unity Connection 7.X or latter on the call handler template check box, have a look at http://cisco.biz/en/US/docs/voice_ip_comm/connection/7x/gui_reference/guide/7xcucgrgpdf.pdf and search for the term “Wait While I Transfer Your Call” in the PDF.
Hope this helps,
Craig
(PLEASE RATE HELPFUL POSTS)

Similar Messages

Authentications Video Call for Cisco Unity

Dears,
I need to authenticate incoming video calls, with PIN or Password.
I thought about using the Unity Connection.
Could anyone give me some guidance?
Att,
Eduardo Lassance

Hi there,
Do you have locations based CAC enabled that is limiting video between regions? Also any firewall between locations?
HTH,
Chris
Sent from Cisco Technical Support iPhone App

Degradation in calls to Cisco Unity

Hi, if someone has a issue like me,i hope someone can help.
I have a CUC´n Rls. 9.1, when i call to any Extension and the call goes to VM, but in the call hear it noise or degradation , i check everyone of the components and it´s ok, the Router, Switch ports, CUCM, and CUC´s but i still has the same issue
Thanks

Any One Have any idea

Unity 5.0(1) System error when calling into CUGA (Cisco Unity Greetings Administrator)

When I call into CUGA (Cisco Unity Greetings Administrator), I get a failsafe message and the system hangs up. The below events are written in EventViewer. GUSI and AvCsMgr Diags attached.
Any help would be much appreciated.
Event Type: Error
Event Source: CiscoUnity_Miu
Event Category: Error
Event ID: 531
Date: 5/28/2011
Time: 5:23:51 PM
User: N/A
Computer: NYLCNJUN01
Description:
Cisco Unity's telephony component has encountered a serious error.
EXPLANATION:
A serious failure has occurred on port 53 while trying to open a wav file or stream. Depending upon the severity of the failure, parties on this call could experience unexpected behavior or be disconnected. In some cases, further calls on this port will not be handled correctly.
TECHNICAL DETAILS:
Thread 0x00002220 had a failure on port 53 in method CAvMiuWave::GetLength()
DESCRIPTION: AvWav WavOpenEx2 failed with 0x00000000.
DETAILS:
FileName: Welcome.
CALLINFO:
CallerID: 2003406
CalledID: 3007910
RedirectingID: 3007910
Origin: Internal
Reason: FwdUncond
Trunk: 0.
CALL SEQUENCE:
[15:17:29:794 - 0x00002100] Drop() - S_OK
[17:23:51:209 - 0x00001D6C] LINE_APPNEWCALL(0x000115D3)
[17:23:51:209 - 0x00001D6C] SetEvent(NewCall)
[17:23:51:209 - 0x00001D6C] SetEvent(CallInfoArrived)
[17:23:51:302 - 0x00002220] Answer() entered
[17:23:51:302 - 0x00002220] lineAnswer(0x000115D3) - 0x00011439
[17:23:51:302 - 0x00001D6C] LINE_REPLY(0x00011439 | 0x00000000)
[17:23:51:427 - 0x00001D6C] StopIO(TERM_REPLAY) entered
[17:23:51:427 - 0x00001D6C] StopIO(TERM_REPLAY) - S_OK
[17:23:51:427 - 0x00001D6C] LINECALLSTATE_CONNECTED(0x000115D3 | Active)
[17:23:51:427 - 0x00002220] WaitFor(0x00011439 | CONNECTED) - CONNECTED
[17:23:51:427 - 0x00002220] Answer() - S_MIU_CONNECTED
[17:23:51:427 - 0x00002220] GetMediaLength() entered
[17:23:51:427 - 0x00002220] WavOpen(Welcome) - 0x00000000
[17:23:51:427 - 0x00002220] GetMediaLength() - 0 | E_FAIL
[17:23:51:427 - 0x00002220] Play() entered
[17:23:51:443 - 0x00002220] WavOpen(Welcome) - 0x00000000.
Event Type: Error
Event Source: CiscoUnity_Wav
Event Category: Error
Event ID: 807
Date: 5/28/2011
Time: 5:23:51 PM
User: N/A
Computer: NYLCNJUN01
Description:
Cisco Unity's multi-media component has encountered a serious error.
EXPLANATION:
A serious failure has occurred on port 53 while opening an audio stream. Depending upon the severity of the failure, parties on this call could experience unexpected behavior or be disconnected. In some cases, further calls on this port will not be handled correctly.
TECHNICAL DETAILS:
Thread 0x00002220 had a Failure on Port 53 in AvWav
DESCRIPTION:
File: H:\views\CUESB1_view\un_Miu\UnityAvWav\WAV.cpp(1095)
Method: WavOpenEx
Failure: call to mmioOpen(Welcome) failed(101).

Tommer,
I found the issue that caused problem.
One of the Unity Admins (hand slapped) used RDP in Console mode which redirected the custom wave driver. This is a known issue with using RDP in Console mode in Windows 2003. There is a MS Hotfix 928046 that should have prevented this from happenning, but it was alraedy installed. A Server reboot cleared the condition and its all working again.
Thanks for the reply.

Cisco Unity 7: Voice mail cann't get the name or Number phone of the caller

Hi,
I have installed Cisco Unity Messaging Unified version 7 and integrated with Exchange 2010.
I have two scenario, and I want to know if are normal or not:
1. If the 2 IP phones are subscribed with Cisco Unity: the first IP phone call the other IP phone and let a voice mail. When the second IP phone check his message vocal it can get the name of the caller or his number phone (the message is: You have One message from XXXX) and he get e-mail as objet: Voice Mail from XXXX.
2. If one IP phone is not subscriber with cisco unity call other Ip phone subscribed with cisco unity and let him a voice mail. The second IP phone when check his message vocal it can’t get the name of the caller or his number phone: The message is: You have one voice mail xxxx; without indicate from!! and he get a e-mail as object: Voice mail from Unknown.
Please, I want to know if the second scenario is normal ? if not, who to resolve this problem? I want that he indicate the number of caller same he isn't subscriber with cisco unity?
Thanks a lot,
Best regards,
Omar YUNSI

So for the 2nd scenerio you would want to check what your Message Subjects were set to. For Unity 7 open Web SA, click Configuration and then Message Subjects. Make sure that the Outside Caller Message has %CALLERID% in it somewhere. The value %CALLERNAME% will return unknown if we do not receive a name from the PSTN.
Try setting the Outside Caller Message to:
%U% %P% Voice Message from %CALLERID%
and that should get you your desired results.
The default Message subject is:
%U% %P% Voice Message from %CALLERNAME% (%CALLERID%). So with that it would say Voice Message fom Unknown (xxxx) if it was not able to determine the name of the user which is usually normal from a PSTN call.
Just to note, the From address is always going to say from Unity Messaging System, it will only be the subject that has the extension in it.
Bryan

Will Cisco Unity inbox show the calling name from non-subscribers

Unity CX 7.1.3 -- I need to know if the calling name is present will CUCM pass this to Unity CX and show the name in the messages "from" field on the Cisco Unity Inbox (personal communications assistant) I currently have a PIMG integration and there is no name field in the SMDI traces.
thanks

Hi -
Sorry, I misunderstood your original posting. Here is a link to Unity Connection for customizing the subject line of voice messages - http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/administration/guide/7xcucsagpdf.pdf
The subject line is viewable using the Cisco Unity Inbox. Note however, this is not ciscopca, which is used to configure user voicemail settings. As you can see from the link, "When the %NAME% parameter is used in the subject line format of an outside caller message, it is automatically replaced with the ANI Caller Name of the sender of the message. If the ANI Caller Name is not available, Cisco Unity Connection inserts the value specified in the %NAME% (When Unknown) field." If the message comes from a non-subscriber, you may see "Voice Message from Unknown Caller" or Unidentified Caller in the subject. I recommend also using field %CALLERID%, which I believe is used by default, because at least the voicemail user will get the caller's phone number.
Ginger

Broken Cisco Unity / Unified Communications Manager association

We have several Cisco Unity Connection users with the following status in their profiles:
"This user's association to the co-resident Cisco Unified Communications Manager user has been broken.
Please Click Here to reassociate the orphaned user."
Clicking on the reassociation button does not show any of the users with broken associations, just a few resource users.
Is there any way to reassociate these users with CUCM without having to delete them in Unity Connection along with their mailboxes?

These are the steps I took to resolve the issue. I was particularly concerned about users losing saved messages in their voicemail. The posted solution did not give much detail on what to do.
1) Create a new user in CUCM. For example, I have a user called 'John Doe' in the system. I created a new one called 'John Doe2'.
2) After creating the user I associated 'John Doe2' to the phone in use by 'John Doe'. Then I set the Primary Extension as needed for that user. Hit the 'Save' button and verify that the 'Create Cisco Unity User' option shows up in the drop-down box in the right hand corner.
3) Log into Cisco Unity Connection Administration, and select 'John Doe'. Click on the link to re-associate and select 'John Doe2'. This links the Unity user to the CUCM user.
4) Log back into CUCM and select 'John Doe' from the user list. Remove all device associations from the user. Hit Save, then delete the user.
5) Select 'John Doe2' and rename the user as 'John Doe'.
These steps fixed my problem. I had to do it for all the users whose association was broken. One note to make is that the voicemail PIN is automatically reset to the default I believe, which is 0000. Other than that voicemail continues to work normally and users don't have to redo their greetings and such.

Need Help - Cisco Unity

DEAR
i am experiecing problem on cisco unity. i have a doubt but not sure. I was configuring call management - Auto Attendant. I didn't make any big changed i just created one handler thats it and deleted later.
After that i am not getting voice mail even if i check from cisco iphone its not asking pin code and message operator not available at this moment.
i checked users are created. what coulf be the issue.

Dear Mr. Mahmood;
I really appreciate your concern and solution to the point and well understanding about the issue, Thanks alot.
One more issue, recently i have configured IM & Presence 9.x. cisco jabber voice is working on android and iphone within coporate network. Like Lync Server, you don't need for any vpn because configuration on doman level. Can we do like that if not is there any VPN software which i can install on phone. we have ASA 5500 series firewall with VPN - group tunnel password. I install cisco anyconnect but there is no option for Group Tunnel Password.
Is there any best way for conectivity using jabber without coporate network please suggest me...

Cisco Unity Express 8.6.6 Voice Mail not deleting when e-mail with attachment deleted

I have a Cisco Unity Communications Manager rel 9.1.2 that supports a remote location with a Unity Express rel 8.6.6 voice mail service module in the voice gateway to insure if WAN goes down the location still has voice mail. We have Voice Mail to E-Mail working. The problem is that when the e-mail with the voice mail is deleted the message stays in the Unity Express Voice Mail Box. All of our local users on the same Call Manager Cluster using a local Unity Connection Cluster rel 9.1.2 have the voicemails deleted when the e-mail is deleted.
How can I resolve this issue?

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Voice mail is not stored in cisco unity 7.0(2)

We have configured exchange2003 and cisco unity in the same MCS(7845 IBM) box. We have done with integrating it to CCM 7.1.3 using SCCP. When we make a call from sub A to sub B, if sub B doesnt answer the call it is forwarded to Cisco Unity and the greetings are played. when we tried to record the message and play back it is not played back also when we send that message, message is not reaching sub B (phone keypresses are taken). Please any one help me to solve this issue.
Thanks,
Nithiya.

Adding Languages
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/upgrade/guide/ex/5xcuruge030.html#wp1104842
If the other question is about an AA all you need is a CTI RP with CFA to VM, a call handler with matching DN and record the greeting.
If you need more options configure new call handlers and use the caller input config from the first call handler.
HTH
java
If this helps, please rate
www.cisco.com/go/pdihelpdesk

Unable to create a notification for a group (Cisco Unity Express 3.2)

There is Cisco ISR 2821 with CME 7.1 and Cisco Unity Express 3.2.
I am trying to create notifications for a group named AAA in CUE.
I do following (GUI):
1. Go to Configure -> Groups
2. Click on the group name AAA.
3. In Group Profile window 'Enable notification for this user/group' option is enabled.
4. Go to Mailbox tab. There is an associated mailbox with ticks against Enabled and Fax Enabled.
5. Go to Notification tab and see the warning:
No Notification Devices found for User/Group
Also, there are another several groups on this system and I am able to turn notification on for them. These groups have the same owners and members that AAA has. Moreover, if I create a new group and set it up absolutely the same as AAA, I can turn notifications on for it.
The problem in this way is that we have our custom greetings and after I created a new group, for example BBB, with the same settings (as AAA, inluding Primary Extansion and Primary E.164 Number) and remove these numbers from AAA, then it works and users would receive notification about new voice messages. BUT, when I call BBB I listen to standart Cisco greeting promts.
I don't undestand why it happens, because all these greetings are determined in Voicemail -> Auto Attendant section and I did not any changes here at all.
How can I fix this 'notification' problem?
Thanks.

Process with success:
unzip the packet in: C:\APEX
1. Install:
@apexins SYSAUX SYSAUX TEMP /i/
2. Change to password:
@apxchpwd,
3. Run apex_epg_config.sql
On windows:
@apex_epg_config.sql (page 30, the guide of intallation)
Important:Replace SYSTEM_DRIVE:\TEMP by C:
E.g.: @apex_epg_config C:
After this, follow the next steps
4. ALTER USER ANONYMOUS ACCOUNT UNLOCK;
Finish! Just execute apxldimg.sql script if you is upgrading from a preview release.
Now try the connect on the browser IE6 o later:
http://localhost:8080/apex/apex_admin
Then create your workspace.
Edited by: [email protected] on 10/03/2009 11:59

Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

Hello,
Currently Running:
Cisco Unified Communications Manager 8.6.2
Cisco Unity Connection 8.6.2
Problem:
when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
I also have the message relaying to my E-mail and I get the same in the subject line.
"Message from Cisco Unity Connection Messaging System (Unknown extension)"
This tends to be a big deal with the Sales team as customers will call and say "Call me back"
But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
Any help will be appreciated.
Thanks
Tim

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Cisco Unity Aging Policy Not workin as intended

HI ,
We have cisco unity connection 8.5 integrated with call manager 8.5. We face issue on the aging policy values set. Permanently delete all secure message that are older than _ days, value has been set and is not working as intended,Once's the value have changed should the connection agent service to be restarted? Have any 1 faced such issue ?
Thanks,
Rahul

I just noticed that we are having this issue as well. What was the resolution that Cisco gave to you? I'm curious.
Thanks,
Josh

Setting up Directory Handlers under Cisco Unity Connection

Good Day All,
I am in the process of setting up directory handlers for Cisco Unity connection.
When I dial the extension for the directory handler ; I hear the default Cisco Unity connection greeting instead of being prompted for the search.
Can anyone shed any light on why this is happening?
Any help is greatly appreciated.
Thanks very much
Regards
Amanda

Hi javalenc,
Of course , that was right. I worked it out in the end.
I was trying to copy the configuration from an older version of CUC and basically added an un-needed call forwarding rule under the Directory Handler. As soon as I removed it; the directory worked normally.
The other thing I learned last weekend was that the order of the routing rules is important.
My directory had the first priority and it was causing people who wanted to leave a voicemail for other users to get the prompts for the directory.
Thanks so much for the help though.
Regards,
Amanda Lalli-Cafini

Cisco Unity 7 Problem in Message Store Wiard. Showing some SRV Records Missing in DNS Table. Please suggest and help on this matter.

Installed Cisco Unity 7 on Windows Server 2000 and Unity Server is on Domain,and Exchange we are using is Exhcnage 2007. When we reach at Message Store Wizard it is showing some error at the end that " Failed reaching for Unity in Active Directory Global Catalog. The SVR Record may be missing in DNS Table" . It shows when we slected Exchange in Process and the Selected Storage Group. And the it takes time and then shows error. Please try to resolve this issue soon, we need this solution urgently. We have already spent several days on different issues regarding Unity.
If you need to talk regarding this matter, Please contact on +919780660619, and the conatct person name is Manav.
Thanks in Advance
Rosy

Rosy,
We cannot call you from this forum. If you truly need a call, you can open a TAC case. The info I can tell you is that you need to fix this in your dns. A simple google search of "no SRV record Windows 2000 server" comes up with numerous resources that can help you fix this. Here is just one example.
http://support.microsoft.com/kb/241505
and
http://www.petri.co.il/active_directory_srv_records.htm
I would also advise you, if you are doing a new install with Unity 7 and that version of Exchange, that you use Windows 2003 as the OS. Even MS doesn't support Windows 2000 Server any more so if you end up having an OS issue on your Unity server, we will not be able to get MS to help you. From a support perspective, I would advise you to use Windows 2003 Server in this implimentation.
Thanks!
Tray

Call Hander cisco unity conection

Similar Messages

Maybe you are looking for