Call manager DDI and translation pattern

I have a 2811 router with isdn connectivity. DDI numbers allocated are similar to 455xxx where xxx is 100 to 299
I need the call manager to allow these calls to go to device numbers in the format of 8xxx where the xxx relates to the ddi number.
Is there a good document that details inbound translation that would assist me with this task.
Regards
Simon

If you config your inbound translation in 2811, you can also test and debug the translation rule with IOS commands.
Router# test translation-rule name-tag input-number
Router# show translation-rule [name-tag]
Router# debug translation min
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a0080094681.shtml
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a0080325e8e.shtml

Similar Messages

Toll fraud traffic pumping on a Call manager express and unity express with an 800 toll free number.

I have a customer with a call manager express and a unity express. They have an 800 toll free number that rings in to an auto attendant on the CUE. The problem is something called toll fraud traffic pumping. The caller, always from a different number, reaches the auto attendant by dialing the 800 number. They then somehow manage to keep the line connected for up to 12 hours by somehow staying in the auto attendant. I opened a TAC case and was informed that it is not in Cisco's hands to create a way to disconnect a call that is connected to the CUE. I need a way to have a call that stays in the auto attendant or voicemail after 3 to 5 minutes. I can't see a way to do it in the auto attendant script. Can someone help with a method that will disconnect the caller if they stay in the CUE for a period of time?

Thank you for the response Jaime.
That is what TAC told me. I am not familiar with TCL scripting and I have been looking at some guides on it. Any advice on a source to go to for assistance with that, possibly someone to help?

Cisco Call Manager MIB and OID.

Hi,
One of our customer has developed their own NMS software to manage multiple OEM products.
They want to integrate Cisco Call Manager 7.0 and Cisco Router with the NMS software for monitoring/managing of Voice traffic.
The monitoring of CUCM 7.0 will consists of the following-
1. Call History
2. Missed calls.
3. Calls in progress,
4, Dropped Calls.
The Monitoring of Cisco Router will Consists of Interface statistics and Portwise Traffic statistics of LAN and WAN Ports.
I believe this monitoring is done through Call Detailed Record and if I will load the CDR MIBs in NMS software it will be able to log CRD logs from CUCM 7.0.
Please suggest that if the same is possible.??.
kindly help me in getting the MIBs/OIDs for the same.
Best regards,
Puneet K.

Hi,
For 200+ users you should better go with Cisco CallManager (CUCM). Although ISR G2 supports 250+ users, it will not provide clustering mechanism and additional HA capabilities as CUCM does.
You can read the Call Processing chapter of the CUCM SRND:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/9x/callpros.html
Hope to help, please remember to rate helpful posts.
Kind regards,
- Adrian.

CDR for translation patterns (DIDs)?

We have some "legacy" DID numbers -- they enter Call Manager where a translation pattern sends them to the current, new number.
Is there someplace the call detail records I can find how often a particular DID (or particular translation pattern) was actually used? If these numbers are no longer in use, we could drop them when we switch carriers in the next month or so.

Although there is no translation information in the CDRs, there is a service parameter which supposedly puts extra information into the traces.
Digit Analysis Complexity : This parameter allows the user to toggle between two modes; that is, StandardAnalysis and TranslationAndAlternatePatternAnalysis. The TranslationAndAlternatePatternAnalysis mode gives information about the Translation pattern and the Alternate matches in the CCM Traces while finding a match for a pattern. The valid values for this field follow:
-- StandardAnalysis
-- TranslationAndAlternatePatternAnalysis
This is a required field.
Default: StandardAnalysis.
Please rate the post if it helps

Call manager and IP phones

after the basement remodel i will have a server and computer repair area for my testing. I have a call manager server and a couple of ip phones and would like to setup a phone at each of my families houses. what would i need and how would i set it up.

there might be a way to do it using SIP but I have not done it and I am just giving you an idea of how to do it with SCCP default and in a secure way
Forget about the router model I was talking about.
You would have to assume that your home where the CCM is as the Main site and pretty much have all othere families as remote sites, you would need to setup VPN between the houses and if you want everyone to dial each other you would need DMVPN(Dynamic Multipoint).
You would need a good router at the main site, depending on how many sites you have you may be able to use just a 2801. For the remote sites, I would think you can use an 871 or 831 router which does VPN and also has a few PoE ports switch.
You would have to create tunnels between each other house.
JoeL

Call Manager and OCS

Hello,
I have Call Manager 7 and Microsoft OCS.
Both of them work properly.
There are 1xx DNs on CM adn 5xx DNs on OCS.
Everyone have one CM number and one OCS number.
I want to do that:
When i called 1xy, both ocs (5xy) and cm (1xy) numbers must ring.
Is it possible? And how?

Good Afternoon,
I would use the Single Number Reach feature, when the Cisco phone starts ringing a second call starts(after a delay configure by you) passes a call to in most circumstances your mobile but your OCS would work.
Have a look at this document on how to configure this feature:- http://www.cisco.com/en/US/docs/voice_ip_comm/hucs/7.1a/provision/CH13_HUCS.html
Hope this helps,
Craig
(PLEASE RATE HELPFUL POSTS)

Translation Pattern digit problem

We have created a translation pattern (6925) which allows our users to call an internal number in order for them to get routed out to their external helpdesk via the PSTN (908456016925). Initially this didnt work as the translation patter number of 6925 did not have the correct Calling Search Space to get routed out of the voice gateway.
That is now fixed however every time you dial 6925 you get a dead tone when dialling the number 2. If you press 5 immediately the call routes to the translation pattern and out to the helpdesk. This is not ideal as many users are putting the phone down when they get the dead tone as they think the number is incorrect.
I have checked our dial plan route plan report and can confirm that no other device etc has been allocated a number beginning with 692.
I've also created another translation patter (6935) to the same PSTN number and this works fine ie no dead tone when I dial the digit '3'. In fact I have tested 3,4,5 etc and they are fine its just 692.
Any help would be appreciated.......
BSOC

My first step would be to remove the 6925 translation from CM. Once removed, I would try dialing 6925 to see what happens, knowing full well that it should not work. If there are any other patterns or devices beginning with 69 it should fail after pressing the 2 since there is nothing that matches. I would then add the 6925 translation back in and test again. Let us know!
Tony

Anti-virus on UCCX/Call Manager

Hello I have been asked a questiona bout adding Anti-Virus to our Phone System Environment.
We have Call Manager 7 and UCCX 7.
What are the best practices for doing so?

The Compatibility Matrix has a section for Security/AntiVirus Software will tell you which AntiVirus is official supported: http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf
The best practices guide simply mentions "Cisco does not permit any unapproved third party software on the UCCX server. Only Cisco approved anti-virus, anti-spy ware software should be used along with the compatible version of Cisco Security Agent."
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_7_0/reference/guide/UCCX_Best_Practices.pdf

Cisco Call Manager 9 ELM question

Hello everyone!
We start using ELM for Call Manager Licensing and I just can not understand they way it works. I am used to DLUs and can not undertand the new scheme
Just to make is clear:
We have
Enhanced (9.x) - Unified CM Available - 180 Installed
Does it mean we can register 180 IP phones?
And we also have
Used - 8, Required
What is meant by Required?
Thank you!

It means you are entitled to 180Enhanced UCSL users (users with up to 2 devices), you have 18 such users currently provisioned and 132 still available. This does not mean you can have 180 such devices, it means you can have 180 users with 2 devices such as phone or softphone assigned to them or any 79XX, 89XX, 99XX phones.
The 21 and 9 are basic (69XX phone) and essential (3905, 6901 phone), since you don't have any of these licenses, they are being borrowed from the upper tier.
HTH,
Chris

Cisco Call manager maintainance

Dear Friends,
I have a MCS-7835 call manager server,with 80GB HDD capacity,in which nearly 60gb space is occupied with call manager soft and lots of log file for last 1yr.Can anone suggest me which files are to be deleted for freeing the HDD space.
Regards,
kumarjeet

Hi Kumarjeet
From http://msdn2.microsoft.com/en-us/library/aa174538(SQL.80).aspx
If log records were never deleted from the transaction log, the logical log would grow until it filled all the available space on the disks holding the physical log files. At some point in time, old log records no longer necessary for recovering or restoring a database must be deleted to make way for new log records. The process of deleting these log records to reduce the size of the logical log is called truncating the log
This said, it is very important to keep a backup of your system at any stage. Hence installing and taking backup with BARS should be your first step.
Truncating of logs would not be deleting any CDR records as such.

Cisco call manager pub & sub definitions

I'm just beginning to learn Cisco VOIP. Can someone explain to me in a simple way what SUB & PUB mean in relation to Cisco Unity & call manager mean, and how it's used in the real world. My supervisor wants me to do a unity & UCM backup, and I'm not really sure what I'm doing
Thank You very much.

PUB = Publisher
SUB = Subscriber.
In simple terms, think of the Publisher as the manager of the CUCM cluster. Configuration changes are typically done on the Publisher, and it distributes those changes to the Subscribers. Subscribers perform call processing, phone registration, software conference bridge, music on hold, etc., and in some setups the Publisher will as well (depends on size and design, as Jaime mentioned).
The Pub-Sub relation for Unity is a little different... which one handles voicemail traffic depends completely on how the connectivity with CUCM is configured. In some setups, they will be distributed voicemail traffic evenly, while in other setups the Pub may get all traffic until its ports are full, and then overflow to the Sub as a backup.

Call manager in linux

Hello
It is just to know not for implementation or some other purpose. What is the software used in linux which resembles cisco call manager. Does it have powerfull features as cisco call manager offers and easily configurable ?. Could please answer me ?. Thanks in advance.

909033 wrote:
It is just to know not for implementation or some other purpose. What is the software used in linux which resembles cisco call manager. Does it have powerfull features as cisco call manager offers and easily configurable ?. Could please answer me ?. Thanks in advance.Asterisk and FreeSWITCH are the two leading Open Source PBX software implementations for Linux.

Call Manager 10 License Standard License

Customer has Call Manager 10 and wants to add 220 Phones with Standard License including voicemail capability. What is the TOP level PN please?

Hi Anas,
thanks for sharing more info[+5]
I was referring the messaging ordering guide which says
With version 10.x, there are now two types of users - Basic and Enhanced.
●
Basic (formerly referred to as "Standard" a-la-carte) user functionality is unchanged from 9.0. It includes all user-based features such as voicemail, integrated, and unified messaging capabilities, as well as automated speech recognition and more.
●
Enhanced users are new for 9.1 and the same with 10.x. Enhanced includes all Basic user functionality plus the ability to configure the user for SRSV.
●
You may mix Basic and Enhanced users on the same Cisco Unity Connection server. Only Enhanced users may be configured for a branch SRSV system.
Part Code is UNITYCN10-STD-USR
UNITYCN10-ENH-USR
regds,
aman

Changing the Compact Flash on Cisco 2821 Call Manager Express

Hello All,
I'm gonna have to swap the compact flash on a Cisco 2821 who is serving as the Call Manager express and the Dialling Router.
What's the best way of approaching this? As far as i know it doesn't have a second slot? And i just can't plug it in and copy everything from 1 flash to another.
Must i copy all of the files on the flash to my tftp or? How can i be sure that everything will be copied to the new flash? I will be creating downtime i suppose? since when i'm copying towards the new flash the router will not properly work with the previous configuration

So i figured out that i can use the archive tar /create command:
To copy the entire flash towards TFTP:
archive tar /create tftp://X.X.X.X/flash.tar flash:
Now i will have to insert the new flash and probably format it first towards the correct file systems. Then i will have to use the next archive command:
archive tar /xtract "Here i am unsure of the syntax, i want to be copying and extracting the tar I backed up from the old flash"
After these steps are complete can i just reboot the router with the new flash card, won't there be any issues, since the startup config is on the NVRAM it will load the config properly, and i haven't seen any boot parameters but they shouldn't pose any issues since i'm not changing the flash slot.
Thanks for your assistance

Call Manager Express ringback tones

I have a call manager express, and when I call I hear the ringing signal and would like to hear music on hold.
Is it possible?
Thanks

David, which of the previous responses answered your question? Please respond to this comment and let us know. This will help us attribute the contributions of our community members correctly, as well as, make it easier for others to find the correct answers.
Posted by WebUser Cisco NetPro

Call manager DDI and translation pattern

Similar Messages

Maybe you are looking for