Call Manager Express Hunt Group roll over doesn't work correctly

Hello,I have a wierd issue occuring on the CME portion of a client's UC520. Currently, I have a hunt group set up that has 1 user and then the auto attendant. Basically, I want to give a user a chance to answer the main line, and if she doesn't, it then roll's to the main auto attendant. This is working as long as I keep the time out on the hunt group under 12 seconds. The issue is that is about 2.5 rings. She'd like a little more time to be able to pick it up. When I put the time out above 12 seconds (say 16) and dial from an external number, it rings her phone correctly, then you can hear it attempt to transfer, but it transfers it back to her phone instead of rolling over to the auto attendant. You can even see on her phone that the transfer occurs and it transfers to herself. For an instance, it shows 2 calls with the same caller ID. Change the time out back under to 12 or under, and everything works great. Any help would be greatly appreciated.

Sorry about that. Here is the IOS.
Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
And here is some relevant code.
ephone-hunt 1 sequential
pilot 501
list 201
final 401
timeout 11
no-reg pilot
statistics collect
destination-pattern 401
b2bua
voice-class sip outbound-proxy ipv4:10.1.10.1
session protocol sipv2
session target ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad

Similar Messages

  • Functions Call manager express

    Hi,
    I have a contact center express with standard licenses and over call manager express.
    Can i can change the calls flow via web like in Call manager express CUE or is only for premium licenses?
    Do you know any link where i can find it?
    Thanks

    Hi Zamoranoco,
    You can change the call flows i.e.UCCX scripts by using the UCCX Editor. You need to install the Editor from UCCX Admin->Tools->Plugin page on the supported client platform.
    You can use the UCCX Admin user to login into this UCCX editor and make changes.
    Please refer the UCCX Scripting guides from the below link,
    http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_programming_reference_guides_list.html
    For supported UCCX Editor client platfrom refer the below link,
    http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf
    Hope this helps.
    Anand
    Please rate helpful posts by clicking on the stars below the right answers !!

  • Call transfer through Hunt group

    Hi,
    we have a call manager version 8.6 where we have mutiple huntgroups configured. Following is the call flow
    PSTN callers call a DID number from outside which after the translation on the gateway, hits a hunt pilot number on call manager and eventually the call rings on all the line members of the line group. One any of the line group member picks up the call and tries to transfer the call to any internal or external number, we get the following error message on phone screen and transfer does not work
    " External transfer Restricted"
    Now this happens even if we dial the hunt pilot number internally from an iphone and then if one of the members tries to transfer to an internal extension or external number, we get the error message
    More Information:
    There are many other hunt groups on the same call manager server and tries to transfer the call same way as the non working one and it works for them
    So i checked the difference. All the members of all the hunt groups are device profile logged into physical phone. The only difference was that working hunt group members are logged into 6921 phone where as non working users are logged into 7942 phones (sip firmare) and the profile are created for 9971 although we dont have any physical 9971 phone
    So it seems that call transfer through hunt group does not work only if the members are logged into 7942 (sip) phones and works when they are logged into 6921 with 9971 Device profile
    I hope its clear. Please let me know if its a known issue or limitation with 7942 phone. Any help will be appreciated

    Try changing the Block Offnet to Offnet Transfer CallManager Service Parameter to False and test again.  If it then works, we'll probably need CallManager traces to see why both numbers are getting marked as offnet.

  • FAX Machine like using Call Manager Express

    Hi to all,
    Let me share to your my problem, before we have this analog phone which connect to the our printer to have this fax machine to send fax letters, but since the phone line we used to send fax has been cut, so my boss wants me to set up a fax service using  the extension number that we have in our CME (Call Manager Express) VOIP. can any one help me how to configure and set up one extension number of the VOIP using the Call manager Express Gui v7.1 or using the CLI. since i only have a basic knowledge in networking. 
    This topic first appeared in the Spiceworks Community

    Much of Cisco's early SIP work involved proof of concept-proving that SIP worked in an IP telephony environment, with traditional features such as caller ID, call hold, call transfer, and three-way calling. Capabilities such as announcing a call transfer to the recipient before connecting the call (which involves setting up a media stream prior to connecting the call) had to be tested to make sure they would work through RTP streams and SIP-to-public switched telephone network (PSTN) gateways. Similarly, TDM out-of-band signaling (which passes information such as caller ID data) had to be passed via the SIP network.
    Most of the early adopters of SIP technology were young service provider companies looking to differentiate themselves by providing IP-based services. They include Vonage, the IP-based telecommunications services provider that used Cisco SIP gateways and SIP analog telephone adapters (ATAs) to launch its service in 2001, and B2, a Swedish IP-based telephony service provider. But even companies such as Microsoft saw the promise of SIP as far back as 2001, when it launched the SIP-enabled Windows Messenger Update for its MSN .Net initiative. The Windows Messenger Update enabled MSN users to make SIP-enabled voice over IP (VoIP) calls from the MSN Messenger client, with Cisco providing the SIP infrastructure to Microsoft service provider partners.
    Try URL:
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns165/networking_solutions_white_paper0900aecd80131325.shtml

  • Changing the Compact Flash on Cisco 2821 Call Manager Express

    Hello All,
    I'm gonna have to swap the compact flash on a Cisco 2821 who is serving as the Call Manager express and the Dialling Router.
    What's the best way of approaching this? As far as i know it doesn't have a second slot? And i just can't plug it in and copy everything from 1 flash to another.
    Must i copy all of the files on the flash to my tftp or? How can i be sure that everything will be copied to the new flash? I will be creating downtime i suppose? since when i'm copying towards the new flash the router will not properly work with the previous configuration

    So i figured out that i can use the archive tar /create command:
    To copy the entire flash towards TFTP:
    archive tar /create tftp://X.X.X.X/flash.tar flash:
    Now i will have to insert the new flash and probably format it first towards the correct file systems. Then i will have to use the next archive command:
    archive tar /xtract "Here i am unsure of the syntax, i want to be copying and extracting the tar I backed up from the old flash"
    After these steps are complete can i just reboot the router with the new flash card, won't there be any issues, since the startup config is on the NVRAM it will load the config properly, and i haven't seen any boot parameters but they shouldn't pose any issues since i'm not changing the flash slot.
    Thanks for your assistance

  • Toll fraud traffic pumping on a Call manager express and unity express with an 800 toll free number.

    I have a customer with a call manager express and a unity express. They have an 800 toll free number that rings in to an auto attendant on the CUE. The problem is something called toll fraud traffic pumping. The caller, always from a different number, reaches the auto attendant by dialing the 800 number. They then somehow manage to keep the line connected for up to 12 hours by somehow staying in the auto attendant. I opened a TAC case and was informed that it is not in Cisco's hands to create a way to disconnect a call that is connected to the CUE. I need a way to have a call that stays in the auto attendant or voicemail after 3 to 5 minutes. I can't see a way to do it in the auto attendant script. Can someone help with a method that will disconnect the caller if they stay in the CUE for a period of time?

    Thank you for the response Jaime.
    That is what TAC told me. I am not familiar with TCL scripting and I have been looking at some guides on it. Any advice on a source to go to for assistance with that, possibly someone to help?

  • Cisco ip phone 7960 cannot connect to call manager express

    The 7960 ip phone seems not to connect to the call manager express
    router and i have already put the firmware and configured the tftp
    server,the rest of the phones the 7911`s are all working ok,i have tried
    to reset the phone but it doesnt respond to the # key so as to reset to
    factory defaults.
    I have tried all the options of resetting it but to no avail.
    could someone give me some techie tips on this ? could it be a hardware issue ?? please assist.

    Go to the phone and check if the TFTP server is correct (should be the CME IP address). Also check the DHCP address.
    Resetting 7900 Series IP Phones to Factory Defaults:
    http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtml
    Check the bug:
    CSCed93627: Not able to reset 7970 back to factory defaults

  • Starting a Cisco call manager express

    I have a cisco 2651 with Cisco call manager express.
    I have too 15 IP telephones 7902G
    The configuration is in factory default.
    Ì have to create an IP pbx and extensions of a municipality with that components.
    I's like that anybody helps me in the starting configuration, Where can I find good documentation about a tipical case like this?
    I have a lot experience in networking and IP telephony but I'm newbie in CCME.
    Regards

    To begin the configuration use "telephony-service setup" command which will prompt you for some of the basic configuration ie how many phones, starting DN, etc. To add additional feature refer to the admin guide provided by Jorge link.
    Chris

  • Service application development with Call manager express

    Hi everybody,
    I just wanted to know is there anyway to push a message to ip phone when using Cisco call Manager express?
    Thanks,
    Parisa

    Hi,
    thanks for your reply. I have not worked with CME but we have an application for CM and want to be abale to use it for CME customers as well. and therefore I need to ask some more questions:
    -Can we edit authentication URL on phone? As i knew, Authentication url on CM is not editable from phone. It is set on enterprise parameters on Call manager administration. Is it possible to edit this value directly on phone in CME?
    -If I redirect authentication url to my application, what should it return back?
    Thanks,
    Parisa

  • Call Manager Express B-ACD with Call Manager 5 or 6

    Can I use the Call Manager Express B-ACD with Call Manager 5 or 6, because there is no autoattendant in CCM 5 or CCM 6

    Hi Zohaib,
    With CCM (all versions), they do ship with a "stripped down" version of IPCC/CRA which is where the actual AA is built. But this is not really an "on box" solution :( You will need a seperate MCS box to install IPCC on and then integrate with CCM via jtapi. Here is a clip and link for CCM 5.x and a link for 6.x which is a rather large PDF which I am having trouble downloading today;
    Cisco CallManager AutoAttendant
    Cisco CallManager AutoAttendant, a simple automated attendant, allows callers to locate people in your organization without talking to a receptionist. You can customize the prompts that are played for the caller, but you cannot customize how the software interacts with the customer.
    Cisco CallManager AutoAttendant comes bundled with Cisco CallManager on the Cisco CallManager 5 agent IPCC Express bundle.
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a0080531888.html#wp1026233
    Check out the 6.1 Features and Services Guide here;
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
    Hope this helps!
    Rob

  • Phone License for Call Manager express

    Dears ,
    Is the phone license required for Call manager express or the license on the voice gateway enough for operating the phones ?
    Regards,

    Hi Ian,
    I think I may have given you some bad info here. Sorry about that
    Right to Use Feature Licenses
    The following licenses do not Cisco software activation and you can begin using the features upon receipt of the Right to Use Notification
    Feature License Name
    Prerequisites
    License Types
    CME
    IP Base & UC
    Feature (Counted)
    SRST
    IP Base & UC
    Feature (Counted)
    VXML Gateway
    IP Base & UC
    Feature (Counted)
    CUBE
    IP Base & UC
    Feature (Counted)
    Land Mobile Radio
    IP Base & UC
    Feature
    You should be good to go. But a quick note to
    [email protected]
    would be a fair idea.
    Cheers!
    Rob

  • Call Manager Express ringback tones

    I have a call manager express, and when I call I hear the ringing signal and would like to hear music on hold.
    Is it possible?
    Thanks

    David, which of the previous responses answered your question? Please respond to this comment and let us know. This will help us attribute the contributions of our community members correctly, as well as, make it easier for others to find the correct answers.
    Posted by WebUser Cisco NetPro

  • Login to cisco CME as Administrator failed check your call manager express

    Hi Experts
    CME and CUE in one router. when i access the CUE from the IE , i put the CUE username and password and i get in. After that it asks me to enter CME username and password to run the wizard. whenever i put the password i get this crappy message "Login to cisco CME as Administrator failed. check your call manager express config" i have cheked my config many times. Please let me know if someone has faced this problem or any suggestion on this. today is the 2nd time i have faced this problem , last time I cud not solve it and end up wasting 6 hours...
    please help

    Hi friend,
    Here is the Prerequisites for Installing Cisco Unity Express Software. As David describes, may be the CME admin account is missing:
    http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_1/installation/guide/prereq31.html#wpmkr1112912
    Try this, and let us know.
    Best regards,
    - Adrián.

  • Unfied Meetingplace for Call Manager Express??

    Hi! I was told that Meetingplace express is being End Of Life, can you tell me if I can install the recommended Unified MeetingPlace for a new Call Manager Express 8.0install? If so, can use a use a MC7825 server and licenses but what licenses?!?! I'm a little lost here...
    THANKS in advance

    can you tell me if I can install the recommended Unified MeetingPlace for a new Call Manager Express 8.0install?
    Yes with limitations per the SRND: http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cucm/srnd/8x/confernc.html#wp1057454
    If so, can use a use a MC7825 server
    No. You need at least an MCS7835: http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.0_--_System_Requirements_for_Cisco_Unified_MeetingPlace_Release_8.0#Table:_Supported_Cisco_MCS_and_Third-Party_Equivalent_Servers_for_the_Application_Server
    licenses but what licenses?
    I hope you have UCSS coverage left on MPE. The problem is that MP8 and beyond are no longer stand-alone systems; they all require WebEx for the web conferencing. MP8 only provides audio/video conferencing. If you have a WebEx Node for MCS you also get an inside-the-firewall WebEx cloud attachment point for clients. A WebEx contract is required though. Remaining UCSS coverage should provide you that for free through the conclusion of the contract.
    Oh, and MP8 starts at 200 ports. Most MPE customers probably are a better fit for straight-up WebEx MC.
    http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.0_--_Licenses_for_your_Cisco_Unified_MeetingPlace_System

  • 7975 firmware for call manager express

    i would like to add 7975 phone to call manager express.
    where do I get the firmware for 7975 for cme?
    i tried from software.cisco.com but it's for call manager only.

    Hi pranavluhar,
     check this link cme-153-3Mv2.rar (in 10.0 option).There is a 7975 version for CUCME.
    Hope this helps.

Maybe you are looking for

  • Posting date in trip form (TRVFO)

    Hi, I would like to add a date-field in trip-form variant FOXX I.e a date for when the trip is posted. I try to use the field BLDAT, but it does not show correct on the print of the form. Accounting date can be used as an alternative, this is fieldna

  • TCODE- MIR4- Details of Multiple Account Assignment

    Dear SDNers, In the TCode MIR4, We input the invoice doc number and the year and hit on enter. We come to the screen that displays the Invoice Document. In this screen,we are able to see a sub screen headed PO reference. In this PO reference sub scre

  • Documentation for SolMan / ChaRM Security Rolls / Authorizations

    Good Day; I am currently setting up all the roles / authorizations for the different areas within Solution Manager / ChaRM. I have been looking for a u201Cdetailedu201D document on all the security authorizations for Solution Manager / ChaRM. So far

  • My iPod buttons are not working

    I have had my iPod 5 touch for slightly less than a year. Just today my iPod is not responding when i touch it. For example i can use the home button but when i try to put my password pin in its like I'm not even touching it, it doesn't work. THe fun

  • Retrigger output witout giving users VA02

    Hi, My client is doing a GRC implementation and in the process of their roles remediation, we came across many non-Customer service folks having access to VA02 to re-trigger outputs which was causing SOD violations with their other functionality. Is