Call Manager Service

Hi Everyone
I'm taking my PUB out of my call manager group as the 3rd option for phones to register to.I'm moving another server into it's place and I want to turn off the call processing function on my PUB. Is the Cisco Call Manger service the correct service that I need to deactivate under the service activation section?
Eric

Yes

Similar Messages

  • CDR FIles in Call Manager version 7.1.5-30000

    Good Morning:
    I have a cluster of servers Cisco Call Manager version 7.1.5.30000; 01 Publisher and 02 subscriber. The publisher server passes CDR files to a call accounting application PC-SYSTEL on another server. At one point the CDR files are no longer spend the Call Manager to the application PC-SYSTEL
    Call manager services are reviewed, the part of CDR Management in Cisco Unified Serviciability right. The only solution is doing a RESTART to PUBLISHER server,  and then again go CDR files to the application PC-SYSTEL
    Please anyone has any solution other than to give a RESTART PUBLISHER server, or is this the only way to restore this service.
    Expect your news.
    Thanks in advance for any ideas.
    Regards.
    Fernando.

    Hi Fernando,
    Please check the following.
    (1) Confirm that the billing server is configured correctly (verify the IP address). From the Cisco Unified Serviceability page, navigate to Tools > CDR Management to view the billing server parameters.
    (2) Check if you can ping the billing server from the Publisher. From the Publisher CLI, you can use the following command:
    utils network ping a.b.c.d
       where a.b.c.d is the IP address of the billing server
    (3) Check if the FTP (or SFTP) service/software running on the billing server.
    (4) Check if the billing server is running out of disk-space.
    (5) Check if the CDR Respository Manager service is running on the Publisher. If not, start the CDR Repository Manager service.
    (6) On the Publisher, check the 'preserve' and 'destinationX' (X can be 1, 2 or 3) directories for CDR flat files. For example: if transfer of CDR files to billing server is broken from Jan 6th, then use the following commands:
    file list activelog /cm/cdr_repository/preserve/20110106
    file list activelog /cm/cdr_repository/destination1/20110106
      (if multiple billing servers are configuration, the location will be similar to above, but the corresponding directories will be named destination2, destination3). This location contains symbolic links to files under preserve. CDR Repository Manager service uses these soft-links to determine what files need to be transfered to billing server.  
    If you don't observe files in either the 'preserve' or the 'destinationX' locations for the specific date, then it means that problem does not reside on the Publisher. Either the CDR records were not generated by the server that handled the call or it could mean that CDR Agent service on that server could not transfer flat files to the Publisher. Was the 'CDR Enabled Flag is enabled in CallManager service' enabled on that particular date ? Is the CDR Agent service running on the node that handled the call ?
    If you observe files in the 'preserve' directory for the specific date, try restarting the CDR Repository Manager service on the Publisher. If the file transfer to the billing server does not commence, then set the trace level for the CDR Repository Manager service to Debug, wait 10 minutes, download CDR Repository Manager logs via RTMT and engage Cisco-TAC for further troubleshooting.
    HTH
    Manish

  • Error Creating VM on 2011 iMac - The Hyper-V Virtual Machine Management service encountered an unexpected error: The remote procedure call failed. (0x800706BE).

    I am running Hyper-V in Windows 8.1 on a late 2011 27 inch iMac. Whenever I try to create a virtual machine I get the error below and Windows warns that it will restart in 1 minute. I tried a clean install of Windows, but my PC still crashes ever
    time I try to create a VM. I was able to successfully use Hyper-V in prior versions of Windows on this same PC. Any clue as to what is going on? A driver? Windows 8.1? Mac Hardware related?
    I see the following two entries in event viewer but have no other clue as to what is happening:
    Log Name:      Microsoft-Windows-Hyper-V-VMMS-Admin
    Source:        Microsoft-Windows-Hyper-V-VMMS
    Date:          1/10/2014 10:48:46 AM
    Event ID:      16000
    Task Category: None
    Level:         Error
    Keywords:     
    User:          SYSTEM
    Computer:      Charles-PC.CHARLESPOOL.local
    Description:
    The Hyper-V Virtual Machine Management service encountered an unexpected error: The remote procedure call failed. (0x800706BE).
    Event Xml:
    <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
      <System>
        <Provider Name="Microsoft-Windows-Hyper-V-VMMS" Guid="{6066F867-7CA1-4418-85FD-36E3F9C0600C}" />
        <EventID>16000</EventID>
        <Version>0</Version>
        <Level>2</Level>
        <Task>0</Task>
        <Opcode>0</Opcode>
        <Keywords>0x8000000000000000</Keywords>
        <TimeCreated SystemTime="2014-01-10T15:48:46.770451300Z" />
        <EventRecordID>58</EventRecordID>
        <Correlation />
        <Execution ProcessID="2488" ThreadID="8704" />
        <Channel>Microsoft-Windows-Hyper-V-VMMS-Admin</Channel>
        <Computer>Charles-PC.CHARLESPOOL.local</Computer>
        <Security UserID="S-1-5-18" />
      </System>
      <UserData>
        <VmlEventLog xmlns:auto-ns2="http://schemas.microsoft.com/win/2004/08/events" xmlns="http://www.microsoft.com/Windows/Virtualization/Events">
          <ErrorMessage>%%2147944126</ErrorMessage>
          <ErrorCode>0x800706BE</ErrorCode>
        </VmlEventLog>
      </UserData>
    </Event>
    Log Name:      Microsoft-Windows-Hyper-V-VMMS-Admin
    Source:        Microsoft-Windows-Hyper-V-VMMS
    Date:          1/10/2014 10:48:46 AM
    Event ID:      16010
    Task Category: None
    Level:         Error
    Keywords:     
    User:          SYSTEM
    Computer:      Charles-PC.CHARLESPOOL.local
    Description:
    The operation failed.
    Event Xml:
    <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
      <System>
        <Provider Name="Microsoft-Windows-Hyper-V-VMMS" Guid="{6066f867-7ca1-4418-85fd-36e3f9c0600c}" />
        <EventID>16010</EventID>
        <Version>0</Version>
        <Level>2</Level>
        <Task>0</Task>
        <Opcode>0</Opcode>
        <Keywords>0x8000000000000000</Keywords>
        <TimeCreated SystemTime="2014-01-10T15:48:46.773497100Z" />
        <EventRecordID>59</EventRecordID>
        <Correlation />
        <Execution ProcessID="2488" ThreadID="8704" />
        <Channel>Microsoft-Windows-Hyper-V-VMMS-Admin</Channel>
        <Computer>Charles-PC.CHARLESPOOL.local</Computer>
        <Security UserID="S-1-5-18" />
      </System>
      <ProcessingErrorData>
        <ErrorCode>15005</ErrorCode>
        <DataItemName>Parameter0</DataItemName>
        <EventPayload>
        </EventPayload>
      </ProcessingErrorData>
    </Event>

    Hi CharlesPool,
    I am assuming that the win8.1 is in-place updated from win8 .
    Maybe you need to check the state of hypervisorlaunchtype .
    If it is off , please run command " bcdedit /set hypervisorlaunchtype auto "
    Best Regards
    Elton Ji
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Photoshop CS6 could not update successfully.  Error codes Adobe Photoshop 13.0.1.3 Installation failed. Error Code: U44M1P7  Extension Manager 6.0.8 Update Installation failed. Error Code: U44M1P7  Please help me figure out how to call customer service. 

    Photoshop CS6 could not update successfully.  Error codes Adobe Photoshop 13.0.1.3 Installation failed. Error Code: U44M1P7  Extension Manager 6.0.8 Update Installation failed. Error Code: U44M1P7  Please help me figure out how to call customer service.  I would prefer to talk to someone directly.

    Are you using any disk cleaner or optimization tools like CleanMymac or Mackeeper?
    Regards,
    Ashutosh

  • Webpage Service in Call Manager 4.x

    HI All
    Could anyone please tell me which services I need to check in Call manager 4.x if the webpage is not coming up ?
    Thanks in advance

    Hi Rohit,
    you can also refer the link
    http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-callmanager/5258-admin-page-5258.html
    regds,
    aman

  • Call Manager Phone Services to Personal Address Book

    Cisco Forum:
    I'm trying to configure Call Manager (8.6.2.x) for Phone Services so that we can use the IP Phone's Service button to access the Personal Address Book & Fast Dials.  While I have the option (Test PAB-Fast Dial) appearing when the Services button is selected, the process ends with the bottom screen shot showing "Error in Authentication."
    By using the Directories button then selecting the Personal Address Book, I can successfully log into the application.
    What am I missing?  Below is the current URL being used.
    Thank you.
    Dan
    http://10.2.5.234:8080/ccmpd/login.do?name=#DEVICENAME#&service=pab

    Nelson:
    The URL that is working for us is: 
    http://10.2.5.234:8080/ccmpd/pdCheckLogin.do?name=#DEVICENAME#&service=pab
    then use your own IP address for the Call Manager node.
    Our Call Manager configuration is shown below.
    To access the feature, we hit the Services Button, are prompted with a Personal Address Book option, select it, then are promoted for a UserID/PIN (shown further below), at which point I enter my LDAP ID and a PIN.  The PIN is created in Call Manager under User Management ==> End User ==> PIN.
    Good luck with your process.
    Dan

  • Call Manager Cisco SOAP - CDRonDemand Service restarts every 8-10 minutes

    Hello there,
    I just upgraded a customer to 10.5.1.10000-7 of call manager.  Now the Call Manager Cisco SOAP - CDRonDemand Service restarts every 8-10 minutes.
    I tried:
    -rebooting the cluster (pub and sub)
    -restarting the CDR and Soap related servers
    -turning off CDR under service parameters and restarting services.
    Any other thoughts? all replication reports look good
    thanks

    Hi,
    you have probably only two options. Let a TAC person look into it if you really want to know whats wrong. 
    The other option would be to deactivate "Cisco SOAP - CDRonDemand Service" since no appplication is using CDR on demand. That service is only used when an application is pulling CDR records derectly out of the database which seems not be the case.
    Eike

  • Service application development with Call manager express

    Hi everybody,
    I just wanted to know is there anyway to push a message to ip phone when using Cisco call Manager express?
    Thanks,
    Parisa

    Hi,
    thanks for your reply. I have not worked with CME but we have an application for CM and want to be abale to use it for CME customers as well. and therefore I need to ask some more questions:
    -Can we edit authentication URL on phone? As i knew, Authentication url on CM is not editable from phone. It is set on enterprise parameters on Call manager administration. Is it possible to edit this value directly on phone in CME?
    -If I redirect authentication url to my application, what should it return back?
    Thanks,
    Parisa

  • Looking for help - Company is going to Mobile Asset Management service that does not support BB - especially BB 10.

    Hello,
    I am looking for ideas/help. I currently have a BB Z10 (10.1.0.2039) with Verizon Wireless.  The company has a BB Enterprise Server for older devices (I previously was on that).  I bought a Z10 several months ago and have been connecting to the corporate network through Lotus Traveler. They do not have and will not implement a BB 10 Enterprise Server. Some in IT informed that if the company used the BB software they could manage all devices..... not accepted.
    All my contacts, calendar, and company email is funneled to the BB Hub.....
    So my company is implementing a Mobile Asset Management Service that I have to sign up for (Airwatch?).  They only support Android and IPhone.
    Will future versions of the BB OS support Android Apps.... Soon (I have less than 2 weeks)
    I have read where it is possible to put the device in development mode to run Android Apps.  I don't know if that will work with this and have no idea how stable the phone is in that mode. I travel internationally so I don't know how a development mode would work overseas. Any thoughts?
    I like my Z10 but will need to switch to keep functionality if I can't find a work around 
    Any assistance ????
    Thanks for any help.

    Hi and Welcome to the Community!
    BB10 devices have the ability to run .apk apps via special methods. Development Mode is used only for installing the app...not for normal operation. So you install (side-load) the app in Development Mode, then go back to normal mode for normal operations.
    If a .bar file for the .apk app already exists somewhere, you can side load it to the BB10 device and see if it works or not. If there is not yet any .bar file, there is an app called SideSwype that can convert many .apk apps to .bar and install it to your device.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Where do I find the "Node Manager" service?

    Can anyone tell me where to find the "Node Manager Service" In Call Manager 5.1.2 or IPCC 4.5?
    My db_CRA database in IPCC is not updating the real time ICD statistics table and Bug CSCsc09160 seems to indicate that stopping and starting the "Node Managers" may fix the issue.
    From the bug report:
    Symptom:
    Under the db_cra two tables (RtCSQsSummary and RtICDStatistics) are not updating. They stop updating concurrently with engine failovers and reboots. Only a hard reboot or a
    service failover brings them back into an active state.
    When the RtCSQsSummary and RtICDStatistics tables do update on the
    primary DB they do not update on the secondary DB and the data on them
    doesnt get refreshed.
    Conditions:
    stopping Node manager on node 1, data fails to be written to node 2. Then when we start NM back up on node 1 data is still not written to either data store
    Workaround:
    Not much as a workaround, because the solution requirs stop on both Node
    Managers and bring up node 1 first and the data starts writing to DB
    again.
    Thanks,
    Brian

    Post Author: jsanzone
    CA Forum: Authentication
    Sven,
    The reference to Session Manager is more of a concept of operations versus an entity.  The portion of code that you copied and pasted in your post is actually part of the verbiage used in an ASP script that BusinessObjects expects you to create in order for you to obtain your objective.  You can use this coding to create your own customized script or you might be able to search around on the web for a more complete solution.

  • ORA-28868 error when calling Web service over HTTPS from PL/SQL utl_http

    I am getting error message ORA-28868 error when calling Web service over HTTPS from PL/SQL utl_http PL/SQL package,
    when browsed through some of the messages they point to setting Oracle Wallet Manager.
    I am trying to connect
    Any idea on how to resolve this issue ?
    your input is appreciated.
    Thanks
    Ravi

    Duplicate post ... please ignore.

  • Calling web service via utl_dbws with unbounded return values

    Hello, everyone.
    I'm trying to use utl_dbws to call web service from Oracle DB 10 g.
    WS has unbounded return value:
    <xs:element maxOccurs='unbounded' minOccurs='0' name='return' type='xs:string'/>
    I'm setting return paramter in web service call handler like this:
    sys.UTL_DBWS.set_return_type(l_h_service_call, cs_qname_type_string);
    and when I'm trying to call it from PL/SQL function I'm getting an error:
    ORA-29532: Java call terminated by uncaught Java exception:
    deserialization error: XML reader error: unexpected character content: "s2"
    ORA-06512: at "SYS.UTL_DBWS", line 388
    ORA-06512: at "SYS.UTL_DBWS", line 385
    ORA-06512: at line 38
    I've tried to return values by out parameters and got the same exception.
    It looks like utl_dbws needs to know parameters count before calling.
    Have anyone succeded in getting arrays from Web Service call?
    This is a part of wsdl:
    <xs:complexType name='getProcessList'>
    <xs:sequence>
    <xs:element minOccurs='0' name='nameMask' type='xs:string'/>
    </xs:sequence>
    </xs:complexType>
    <xs:complexType name='getProcessListResponse'>
    <xs:sequence>
    <xs:element maxOccurs='unbounded' minOccurs='0' name='return' type='xs:string'/>
    </xs:sequence>
    </xs:complexType>
    Throught SoapUI I can produce such kind of request:
    <soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/" xmlns:proc="http://processmanager.argustelecom.ru/">
    <soapenv:Header/>
    <soapenv:Body>
    <proc:getProcessList>
    <processNameMask>*</processNameMask>
    </proc:getProcessList>
    </soapenv:Body>
    </soapenv:Envelope>
    and get a response:
    <env:Envelope xmlns:env="http://schemas.xmlsoap.org/soap/envelope/">
    <env:Header/>
    <env:Body>
    <ns2:getProcessListResponse xmlns:ns2="http://processmanager.argustelecom.ru/">
    <return>s1</return>
    <return>s2</return>
    <return>s3</return>
    <return>s4</return>
    </ns2:getProcessListResponse>
    </env:Body>
    </env:Envelope>
    PL/SQL function:
    DECLARE
    cs_qname_type_string CONSTANT sys.UTL_DBWS.qname
    := sys.UTL_DBWS.to_qname('http://www.w3.org/2001/XMLSchema', 'string') ;
    cs_qname_type_int CONSTANT sys.UTL_DBWS.qname := sys.UTL_DBWS.to_qname('http://www.w3.org/2001/XMLSchema', 'int');
    cs_qname_type_any CONSTANT sys.UTL_DBWS.qname
    := sys.UTL_DBWS.to_qname('http://www.w3.org/2001/XMLSchema', 'anyType') ;
    cs_endpoint CONSTANT VARCHAR2(256) := 'http://server:8080/process-manager/ProcessManager';
    l_service sys.UTL_DBWS.service;
    l_service_qname sys.UTL_DBWS.qname;
    l_port_qname sys.UTL_DBWS.qname;
    l_operation_qname sys.UTL_DBWS.qname;
    l_h_service_call sys.UTL_DBWS.call;
    l_params sys.UTL_DBWS.anydata_list;
    l_ret_val SYS.ANYDATA;
    BEGIN
    l_service_qname := sys.UTL_DBWS.to_qname(NULL, 'ProcessManagerService');
    l_service := sys.UTL_DBWS.create_service(l_service_qname);
    l_port_qname := sys.UTL_DBWS.to_qname(NULL, 'ProcessListServiceBinding');
    l_operation_qname := sys.UTL_DBWS.to_qname('http://processmanager.argustelecom.ru/', 'getProcessList');
    l_h_service_call := sys.UTL_DBWS.create_call(l_service, l_port_qname, l_operation_qname);
    sys.UTL_DBWS.set_target_endpoint_address(l_h_service_call, cs_endpoint);
    -- return type
    sys.UTL_DBWS.set_return_type(l_h_service_call, cs_qname_type_any);
    -- param type
    sys.UTL_DBWS.ADD_PARAMETER(l_h_service_call, 'processNameMask', cs_qname_type_string, 'ParameterMode.IN');
    l_params(1) := anydata.convertvarchar2('*');
    l_ret_val := sys.UTL_DBWS.invoke(l_h_service_call, l_params);
    IF l_ret_val IS NULL THEN
    DBMS_OUTPUT.put_line('l_ret_val is null');
    ELSE
    DBMS_OUTPUT.put_line('l_ret_val is not null');
    END IF;
    sys.UTL_DBWS.release_call(l_h_service_call);
    END;
    Edited by: Ilya on 03.12.2008 3:50

    Hi Tony
    I'm not sure if you would have solved your problem by now, but with my recent experience with the utl_dbws package, for doc lits with complex data types, you have to call the service with an XML request, as opposed to passing the param array.
    If you still need details, reply accordingly.
    Ta
    cT

  • Error Message "No logical port exists to call web services" installing SM7

    I am trying to use SLM to download a service stack.  However, the option is not available in step 2.5.  There is an error message "No logical port exists to call web services".  I have performed the Wizard install, but the Wizard seems to have left out this step.  I have looked around for documentation on how to configure the port, but cannot find anything more useful than comments to the effect that I should configure the port.

    I found the problem, I think, although I am now on to the next problem.  "Web Services for software lifecycle manager not available'.
    The documentation is lacking.  When the RFC connection is set up, the user id is j2ee_admin, using the install password.  This is not specified anywhere in the install instructions that I could find, there is only a reference to a 'user id and password'.
    The LPCONFIG is used to create a logical port, that ties the RFC to the LP.  However, no name is specified that is to be used for the LP.

  • New Partner Function in CRM (Solution Manager Service Desk)

    Hi CRM Gurus!,
      Even if this problem is present in my Solution Manager Service Desk I'm creating this thread here in CRM Forum because I thin'k I need the experience of one CRM Expert. Í´ve created this question in Solution Manager Forum also but I hadn´t solved my problem yet.
    We add the partner function called "Additional Partner", but I don't know why in the tab "Partners" in the CRM transaction we want to add a new partner but in the partners combo the new one does not appear in the list.
    The procedure that I did was: I created a new business partner function and I added this new function to my partner determination procedure, then in SPRO: "Define Partner Determination Procedures" -> I set the option "Only Functions Assigned in Procedure". 
    These are the values. fro my new function:
    Function: ZSLFN004
    Text: Additional Processor
    Abbrev.: ZAMS
    Function Cat.: 0008 Person Responsible
    Usage: CRM Customer Relationship Managem.
    Relatshp Cat: CRMH06 Is Responsible BP For
    The partner functions in my procedure are:
    00000001 Sold-To Party (CRM)
    00000046 Approved by (CRM)
    SLFN0001 System Administrator (CRM)
    SLFN0002 Reported by (CRM)
    SLFN0003 Support Team (CRM)
    SLFN0004 Message Processor (CRM)
    ZSLFN004 Additional Processor (CRM)
    But in the transactions when I try to add a new partner in the partners tab only the follow functions appears in the combo:
    00000001 Sold-To Party (CRM)
    00000046 Approved by (CRM)
    SLFN0001 System Administrator (CRM)
    SLFN0002 Reported by (CRM)
    SLFN0003 Support Team (CRM)
    SLFN0004 Message Processor (CRM)
    I don't know why my ZSLFN004 is not listed in the combo.
    By the way, my function was created as a copy of SLFN0004.
    Any help would be appreciated.
    Regards
    Gustavo Balboa

    Hi Vishant,
      Thanks for your answer, but some one in the Solution Manager forum gave me the answer few minutes ago :). The problem was that in some transaction types (I don't know wich ones or if it aplies to all) the category 0008 - Person Responsible can only appear once, my partner function was a copy of the function SLFN0004 - Message Processor and that function is defined with the category 0008, so I had 2 partner functions defined in the category 0008.
    To solve the problem I just adjust my Z function and put the category 0016 - Service Team and let the relationship empty. Then the partner function is now showing in the combo at partners tab.
    Again, thanks anyway for the time that you take to answer my question.
    Regards
    Gustavo Balboa

  • Call park service start failed

    Has anybody seen this before?It creates this event on the Lync Front Server and Application Server not starting because of call park service not.
    An unhandled exception was encountered in Call Park Service.
    Exception: System.TypeLoadException: Could not load type 'Microsoft.Rtc.Management.Core.OrbitType' from assembly 'Microsoft.Rtc.Management.Core, Version=5.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'.
       at Microsoft.Rtc.Applications.Cps.CpsConfigManager.ProcessOrbitsFromSquid(CallParkOrbits orbits, Boolean forceDeleteOrbits)
       at Microsoft.Rtc.Applications.Cps.CpsConfigManager.OnCallParkOrbitsChangedEvent(Object source, ConfigChangedEventArgs`1 eventArgs)
       at Microsoft.Rtc.Management.ServiceConsumer.ConfigReg`1.OnTypedXmlChanged(Object source, TypedXmlChangedEventArgs eventArgs)
       at Microsoft.Rtc.Management.ServiceConsumer.RegistrationContext.ProcessChange(TypedXmlReader typedXmlReader)
       at Microsoft.Rtc.Management.ServiceConsumer.RegistrationContext.ApplyLatestDataAndProcessChange(KeyedCollection`2 changes, TypedXmlReader typedXmlReader)
       at Microsoft.Rtc.Management.ServiceConsumer.CallbackManager.OnAnchoredXmlChanged(Object source, AnchoredXmlChangedEventArgs eventArgs)
       at Microsoft.Rtc.Management.ServiceConsumer.TypedXmlReader.OnAnchoredXmlChanged(Object source, AnchoredXmlChangedEventArgs eventArgs)
       at Microsoft.Rtc.Management.ServiceConsumer.CachedAnchoredXmlReader.OnAnchoredXmlChanged(Object source, AnchoredXmlChangedEventArgs eventArgs)
       at Microsoft.Rtc.Management.Store.Sql.SqlWatchedKeySet.PollTimerEvent(Object state)
       at Microsoft.Rtc.Management.Internal.Utilities.SingleshotTimer.InternalCallback(Object obj)
       at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
       at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
       at System.Threading.TimerQueueTimer.CallCallback()
       at System.Threading.TimerQueueTimer.Fire()
       at System.Threading.TimerQueue.FireNextTimers()
    Cause: Internal error in Call Park Service.
    Resolution:
    Restart the service.  If the problem persists contact product support.

    Can you confirm:
    Because you ran the update with Windows Update, when you say run the Lync powershell do you mean:
    Install-CsDatabase -ConfiguredDatabases -SqlServerFqdn SE.FQDN -Verbose
    If you download LyncServerUpdateInstaller.exe from the following article and run it just to check updates, does it show updates are available?
    http://support.microsoft.com/kb/2809243
    I'd strongly suggest just getting this server up to date.
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
    SWC Unified Communications
    This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Maybe you are looking for