Call park using fxs port on spa9000

I have seen this question asked several times but no seems have answered it.
Is it possible to enter a service code to park a call using an analogue phone. If it is, please share what is the service code and the procedure.
I have a spa9000 with pstn (spa3002, spa400) and exts spa-942,xlite and spa2102/pap2. Everything works fine on the 942 phones and the xlite softphones but cant get more that the *98 transfer feature working on the analog phones.

Not so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
*38
*39

Similar Messages

EFTPOS No Response X0 Using FXS Port

Hi All,
Trying to get an EFTPOS machine working connected into an FXS Port using SCCP/STCAPP Protocol for call control.
The port is registered in CUCM, I can connect an analogue phone to the port and successfully call the Bank's 1800 Number etc, I can make other external calls no problem.
When I try the EFTPOS Machine, the call setup runs through normally and I see the call is then in a connected state. Approx about 10 or seconds later the call is cleared by the local device with an 0x8090 code Normal Clearing. The call is then disconnected and released as per any other call.
The EFTPOS Machine prints a error for "Declined No Response X0"
I have attached the following debugs.
debug isdn q931
debug voip vtsp all
debug vop ccapi inout
debug voip rtp session named-event
Calling Number is 0245604627
Called Number is 1800509183
General environment setup is as follows.
EFTPOS connect to FXS Port -> Registered to CUCM (9.1.2) -> SIP Trunk -> IOS 15.x -> ISDN Pri.
Any feedback i smuch appreciated.
Ben

Not so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
*38
*39

Call Manager register fxs port with voice gateway- problem

I have a CUCM 6 and a Voice Gateway V224. I've configured the voice gateway's voice FXS ports as MGCP.
I have a Voip connected and registered to the CUCM and a Pots phone connected to the Voice Gateway.
If i dial from the Voip to the Pots phone it rings. The problem is that i cannot ring from the Pots to the Voip phone.
I have no dial tone.
If i write no shut down on the voice port i have a tone. If i configure mgcp on the voice port i have a busy ringtone.
I've entered no mgcp and mgcp commands and i've reset the voice gateway.
How can i call from the pots to the voip phone?
The ios version on the voice gateway is Version 12.4(22)T4.
Here is an outghtput from the Voice gateway.
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.1.1.33
ccm-manager config
mgcp
mgcp call-agent CCMIOSS 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate domain-name
mgcp rtp payload-type g726r16 static
mgcp profile default
timeout tone busy 600
timeout tone dial 600
dial-peer voice 999223 pots
service mgcpapp
port 2/23
dial-peer voice 999222 pots
service mgcpapp
port 2/22
dial-peer voice 999888 pots
service mgcpapp
port 2/23
The CUCM 6 is registered with the voice gateway.

Is your campaign using CPA? If so, what's the behavior if CPA is not enabled?
I think the best thing to do is to run a trace...
Call Manager > Cisco Unified Serviceability > Trace > Configurations
Select a CUCM server - any subscriber would work.
Service Group - CM Services
Cisco CallManager (Inactive)
Enable SIP Stack Trace and apply to all nodes. Download and install RTMT
Make a bunch of outbound tests and then open RTMT > Trace & Log Central > Collect Files > Check "All Servers" for Cisco CallManager > Next > Next > Relative Range if you made the test calls within the last X minutes, otherwise you can set a From and To datetime. Click Finish and go through your SDL logs and see what errors you find and post them here.
Also, make sure your phone is in the correct CSS in Call Manager

Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup

Hi,
I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?
trunk group HuntGroup1
hunt-scheme round-robin both up
dial-peer voice 1 voip
translation-profile outgoing 7to11
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 1
session protocol sipv2
session target dns:XXXXXXXX
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 300 pots
trunkgroup HuntGroup1
description TEST NUMBER
destination-pattern XXXXXXXXXX
voice-port 2/0
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 1
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/1
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 2
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/2
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 3
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/3
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 4
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/4
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 5
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/5
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 6
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/6
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 7
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/7
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 8
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/8
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 9
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/9
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 10
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/10
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 11
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/11
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 12
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/12
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 13
station-id number XXXXXXXXXX
caller-id enable
Message was edited by: Thomas Schmidt
Added CCSIP Debug and Router Config.

Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks
Regards
Carlo
Sent from Cisco Technical Support iPhone App

Connecting FAX to PSTN line using FXS and FXO ports

I have 2 cisco 1760 routers with FXS and FXO card installed in each. I have to transport 2 PSTN lines from Head Office to remote loaction using FXS and FXO cards and these lines will be used for voice calls and FAX( one line each for FAX and voice). I have configured the router for voice lines and it is working fine. Now I am using the same config for running fax machine but it is not working. Can anyone help me out how to configure FAX in this scenario also if anyone can share any sample config. I am attaching my config for both routers. Right now both routers are connected with a cross-over cable for lab test but we will connect them later using satellite connection.
HO Router (FXO card)
Current configuration : 1718 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
resource policy
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
ip subnet-zero
ip cef
no ip dhcp use vrf connected
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.1 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.1
ip classless
no ip http server
control-plane
voice-port 2/0
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2001
description Remote PSTN#:35296913
music-threshold -70
voice-port 2/1
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2002
description Remote PSTN#:35296914
music-threshold -70
voice-port 3/0
voice-port 3/1
dial-peer voice 2000 voip
destination-pattern 200.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.2
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
dial-peer voice 1321 pots
description line 1
huntstop
destination-pattern 1321
port 2/0
dial-peer voice 1322 pots
description line 2
huntstop
destination-pattern 1322
port 2/1
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end
Remote Router (FXS Card):
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
no aaa new-model
ip subnet-zero
ip cef
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.2 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.2
interface Ethernet1/0
no ip address
shutdown
half-duplex
ip classless
no ip http server
control-plane
voice-port 2/0
description PSTN#:
voice-port 2/1
description PSTN#:
voice-port 3/0
voice-port 3/1
dial-peer voice 2001 pots
description Remote
huntstop
destination-pattern 2001
port 2/0
dial-peer voice 2002 pots
description Remote
huntstop
destination-pattern 2002
port 2/1
dial-peer voice 1320 voip
destination-pattern 132.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.1
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end

In your voice class codec 10 there aren't any codecs declared.
Add G.711 codec in this way:
voice class codec 10
codec preference 1 g711alaw
If the fax communication fails again try to disable T.38 and try fax passthrough mode:
no fax rate
modem passthrough nse codec g711alaw
fax protocol pass-through g711alaw
Regards.

Restricting FXS ports to internal calls only

Hi,
I have recently intalled Call Manager 8.5.1 with a H323 Gateway. On the gateway, I have a number of FXS ports for lobby phones. Is there a way I can restrict these phones to allow only internal calls only? Do I need to use COR lists like in Call Manager express or is there a more practical way?
Thanks,
Derek

Hi Derek,
It sounds like these FXS ports are NOT registered to CUCM 8.5.1? If they aren't, then yes COR lists is the most pratical way to do this. You could do a "connection plar xxxx" to a receptionist extension and her her/him forward the calls to the correct extension.

Lync 2013 Error 31055 ,31059 LS Call Park Service, The database being used by Group Pickup is not the appropriate version and There was a problem communicating with the Group Pickup backend database.

Hello
I have Lync 2013 and 2010 , still i didn't finish my migration completely from 2010 to 2013 .this is coexistence environment that contains both Lync Server 2010 and Lync Server 2013 .
There was no error's in my lync 2013 front end and back end server's and every thing was fine, yesterday I installed windows updated AND CU for my lync 2013 front end and backend server's .
later on after restarting both the front end and the back end server's i start having hundred's of these error's related to "LS Call Park Service".
so any advice for these issue ? and what is the effect for these error .
below is the error I got .
The database being used by Group Pickup is not the appropriate version.
The database is not the correct version:
Connection: Data Source=HQ-LYNC2013-BE.aaaaaaaaaaaaaaaaaaaaaaaaaaa\rtc;Initial Catalog=cpsdyn;Integrated Security=True
Expected... SchemaVersion: 1, SprocVersion: 1, UpgradeVersion: 2
Actual... SchemaVersion: 0, SprocVersion: 0, UpgradeVersion: 0
Cause: The database has not been upgraded.
Resolution:
Upgrade the database to CU1.
==============================================================
There was a problem communicating with the Group Pickup backend database.
There were problems accessing SQL server:
Connection: Data Source=HQ-LYNC2013-BE.aaaaaaaaaaaaaaaaaaaaaaaaaa\rtc;Initial Catalog=cpsdyn;Integrated Security=True
Message: The EXECUTE permission was denied on the object 'DbpGetVersionSchema', database 'cpsdyn', schema 'dbo'.
Error code: -2146232060
Error number: 229
Cause: This may be caused by connectivity issues with the backend database.
Resolution:
Check if SQL backend is running and accepts connections from Group Pickup.
=============================================================================
Kind Regards
MK

Hello
thanks Holger for u r replay .
due to the Microsoft article about the cu :
I run only :
Install-CsDatabase -ConfiguredDatabases -SqlServerFqdn FEBE.FQDN -Verbose
Note In a coexistence environment that contains both Lync Server 2010 and Lync Server 2013 and in which the Central Management Service is located on a Lync Server 2010 pool, do not run the
Install-CsDatabase -CentralManagementDatabase command. If you later move the Central Management Service to a Lync Server 2013 pool, you have to run the
Install-CsDatabase -CentralManagementDatabase command to apply the changes.
here is what I get on my power shell after i run the command : "WARNING: Warning: Failed to execute batch --"
PS C:\Users\MK> Install-CsDatabase -ConfiguredDatabases -SqlServerFqdn HQ-LYNC2013-BE.MyDomain -Verbose
VERBOSE: Creating new log file
"C:\Users\MK\AppData\Local\Temp\2\Install-CsDatabase-82d6613c-f2e3-47e6-8fc4-8f75d2efe6e4.xml".
VERBOSE: Install databases required by Lync Server role(s).
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.BlobStore'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rtcxds.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.AbsDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rtcab.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.RgsConfigDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rgsconfig.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.RgsDynDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rgsdyn.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.CpsDynDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database cpsdyn.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.ArchivingDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\arc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database LcsLog.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.MonitoringDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\mon. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database LcsCDR.
VERBOSE: Assigning "BackendStore:BlobStore:LogPath" to F:\CsData
VERBOSE: Assigning "BackendStore:RtcSharedDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "ArchivingStore:ArchivingDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "MonitoringStore:MonitoringDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "MonitoringStore:QoEMetricsDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "ArchivingStore:ArchivingDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "MonitoringStore:MonitoringDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "MonitoringStore:QoEMetricsDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "ABSStore:AbsDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:RgsConfigDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:RgsDynDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:CpsDynDatabase:LogPath" to F:\CsData
VERBOSE: Assigning "BackendStore:BlobStore:DbPath" to F:\CsData
VERBOSE: Assigning "BackendStore:RtcSharedDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "ABSStore:AbsDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:RgsConfigDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:RgsDynDatabase:DbPath" to F:\CsData
VERBOSE: Assigning "ApplicationStore:CpsDynDatabase:DbPath" to F:\CsData
VERBOSE: Installing "BackendStore" on HQ-LYNC2013-BE.MyDomain\rtc, collocated: False
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.BlobStore'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rtcxds.
Checking state for database rtcxds.
State of database rtcxds is DbState_RequiresMinorUpgrade.
Database rtcxds set to mode Restricted.
Dropping all procedures, functions and views from database rtcxds.
Executing RtcDb.sql...
Adding master role...
Setting owner for database rtcxds to sa.
Creating login MyDomain\RTCHSUniversalServices.
Creating user MyDomain\RTCHSUniversalServices.
Creating Schema MyDomain\RTCHSUniversalServices.
Creating login MyDomain\RTCUniversalReadOnlyAdmins.
Creating user MyDomain\RTCUniversalReadOnlyAdmins.
Creating Schema MyDomain\RTCUniversalReadOnlyAdmins.
Creating login MyDomain\RTCUniversalServerAdmins.
Creating user MyDomain\RTCUniversalServerAdmins.
Creating Schema MyDomain\RTCUniversalServerAdmins.
Adding account MyDomain\RTCHSUniversalServices to role ConsumerRole.
Adding account MyDomain\RTCUniversalReadOnlyAdmins to role ConsumerRole.
Adding account MyDomain\RTCHSUniversalServices to role ReplicatorRole.
Adding account MyDomain\RTCHSUniversalServices to role PublisherRole.
Adding account MyDomain\RTCUniversalServerAdmins to role PublisherRole.
Setting database version: Schema Version 15, Sproc Version 13, Update Version 2.
Setting the database rtcxds to multi user mode.
Database rtcxds is set to multi user mode.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.RtcSharedDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rtcshared.
Database created by script "RtcSharedDatabase" already exists and is current.
VERBOSE: Successfully installed the database. For details, see the following log:
"C:\Users\MK\AppData\Local\Temp\2\Create-BackendStore-HQ-LYNC2013-BE.MyDomain_rtc-[2014_11_13][14_35_01].log"
VERBOSE: Installing "ABSStore" on HQ-LYNC2013-BE.MyDomain\rtc, collocated: False
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.AbsDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rtcab.
Checking state for database rtcab.
State of database rtcab is DbState_RequiresMinorUpgrade.
Database rtcab set to mode Restricted.
Dropping all procedures, functions and views from database rtcab.
Executing RtcAbTypes.sql...
WARNING: Warning: Failed to execute batch --
-- Copyright (c) Microsoft Corporation. All rights reserved.
exec sp_addrole N'ServerRole'.
Executing RtcAbDb.sql...
Setting owner for database rtcab to sa.
Creating login MyDomain\RTCComponentUniversalServices.
Creating user MyDomain\RTCComponentUniversalServices.
Creating Schema MyDomain\RTCComponentUniversalServices.
Adding account MyDomain\RTCComponentUniversalServices to role ServerRole.
Setting database version: Schema Version 62, Sproc Version 42, Update Version 3.
Setting the database rtcab to multi user mode.
Database rtcab is set to multi user mode.
VERBOSE: Successfully installed the database. For details, see the following log:
"C:\Users\MK\AppData\Local\Temp\2\Create-ABSStore-HQ-LYNC2013-BE.MyDomain_rtc-[2014_11_13][14_35_20].log"
VERBOSE: Installing "ApplicationStore" on HQ-LYNC2013-BE.MyDomain\rtc, collocated: False
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.RgsConfigDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rgsconfig.
Database created by script "RgsConfigDatabase" already exists and is current.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.RgsDynDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database rgsdyn.
Database created by script "RgsDynDatabase" already exists and is current.
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.CpsDynDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\rtc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database cpsdyn.
Checking state for database cpsdyn.
State of database cpsdyn is DbState_RequiresMinorUpgrade.
Database cpsdyn set to mode Restricted.
Dropping all procedures, functions and views from database cpsdyn.
Executing CpsDyn.sql...
Setting owner for database cpsdyn to sa.
Creating login MyDomain\RTCComponentUniversalServices.
Creating user MyDomain\RTCComponentUniversalServices.
Creating Schema MyDomain\RTCComponentUniversalServices.
Creating login MyDomain\RTCUniversalReadOnlyAdmins.
Creating user MyDomain\RTCUniversalReadOnlyAdmins.
Creating Schema MyDomain\RTCUniversalReadOnlyAdmins.
Creating login MyDomain\RTCUniversalServerAdmins.
Creating user MyDomain\RTCUniversalServerAdmins.
Creating Schema MyDomain\RTCUniversalServerAdmins.
Adding account MyDomain\RTCComponentUniversalServices to role ReadWriteRole.
Adding account MyDomain\RTCUniversalServerAdmins to role ReadWriteRole.
Adding account MyDomain\RTCUniversalReadOnlyAdmins to role ReadOnlyRole.
Setting database version: Schema Version 1, Sproc Version 1, Update Version 2.
Setting the database cpsdyn to multi user mode.
Database cpsdyn is set to multi user mode.
VERBOSE: Successfully installed the database. For details, see the following log:
"C:\Users\MK\AppData\Local\Temp\2\Create-ApplicationStore-HQ-LYNC2013-BE.MyDomain_rtc-[2014_11_13][14_35_37].log"
VERBOSE: Installing "ArchivingStore" on HQ-LYNC2013-BE.MyDomain\arc, collocated: False
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.ArchivingDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\arc. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database LcsLog.
Database created by script "ArchivingDatabase" already exists and is current.
VERBOSE: Successfully installed the database. For details, see the following log:
"C:\Users\MK\AppData\Local\Temp\2\Create-ArchivingStore-HQ-LYNC2013-BE.MyDomain_arc-[2014_11_13][14_35_51].log"
VERBOSE: Installing "MonitoringStore" on HQ-LYNC2013-BE.MyDomain\mon, collocated: False
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.MonitoringDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\mon. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database LcsCDR.
Checking state for database LcsCDR.
Checking state for database LcsCDR.
State of database LcsCDR is DbState_RequiresMinorUpgrade.
WARNING: The database LcsCDR being updated has data file path at
\\HQ-LYNC2013-BE.MyDomain\C$\CsData\MonitoringStore\mon\DbPath\LcsCDR.mdf and supplied data file path is
\\HQ-LYNC2013-BE.MyDomain\F$\CsData\MonitoringStore\mon\DbPath\LcsCDR.mdf. Supplied path will be ignored.
WARNING: The database LcsCDR being updated has log file path at
\\HQ-LYNC2013-BE.MyDomain\C$\CsData\MonitoringStore\mon\LogPath\LcsCDR.ldf and supplied data file path is
\\HQ-LYNC2013-BE.MyDomain\F$\CsData\MonitoringStore\mon\LogPath\LcsCDR.ldf. Supplied path will be ignored.
Database LcsCDR set to mode Restricted.
Dropping all procedures, functions and views from database LcsCDR.
Executing CdrDb.sql...
Setting owner for database LcsCDR to sa.
Creating login MyDomain\CSAdministrator.
Creating user MyDomain\CSAdministrator.
Creating Schema MyDomain\CSAdministrator.
Creating login MyDomain\RTCComponentUniversalServices.
Creating user MyDomain\RTCComponentUniversalServices.
Creating Schema MyDomain\RTCComponentUniversalServices.
Adding account MyDomain\RTCComponentUniversalServices to role ServerRole.
Adding account MyDomain\RTCComponentUniversalServices to role ReportsReadOnlyRole.
Adding account MyDomain\CSAdministrator to role ReportsReadOnlyRole.
Setting database version: Schema Version 39, Sproc Version 82, Update Version 2.
Setting the database LcsCDR to multi user mode.
Database LcsCDR is set to multi user mode.
SQL Server Agent is running and its start mode was detected as Auto.
Executing CdrJobs.sql...
****Creating DbSetupInstance for 'Microsoft.Rtc.Common.Data.QoEMetricsDatabase'****
Trying to connect to Sql Server HQ-LYNC2013-BE.MyDomain\mon. using windows authentication...
Sql version: Major: 11, Minor: 0, Build 5058.
Sql version is acceptable.
Checking state for database QoEMetrics.
Checking state for database QoEMetrics.
Checking state for database QoEMetrics.
State of database QoEMetrics is DbState_RequiresMinorUpgrade.
WARNING: The database QoEMetrics being updated has data file path at
\\HQ-LYNC2013-BE.MyDomain\C$\CsData\MonitoringStore\mon\DbPath\QoEMetrics.mdf and supplied data file path is
\\HQ-LYNC2013-BE.MyDomain\F$\CsData\MonitoringStore\mon\DbPath\QoEMetrics.mdf. Supplied path will be ignored.
WARNING: The database QoEMetrics being updated has log file path at
\\HQ-LYNC2013-BE.MyDomain\C$\CsData\MonitoringStore\mon\LogPath\QoEMetrics.ldf and supplied data file path is
\\HQ-LYNC2013-BE.MyDomain\F$\CsData\MonitoringStore\mon\LogPath\QoEMetrics.ldf. Supplied path will be ignored.
Database QoEMetrics set to mode Restricted.
Dropping all procedures, functions and views from database QoEMetrics.
Executing QoEDb.sql...
Setting owner for database QoEMetrics to sa.
Creating login MyDomain\RTCComponentUniversalServices.
Creating user MyDomain\RTCComponentUniversalServices.
Creating Schema MyDomain\RTCComponentUniversalServices.
Adding account MyDomain\RTCComponentUniversalServices to role ServerRole.
Setting database version: Schema Version 62, Sproc Version 90, Update Version 1.
Setting the database QoEMetrics to multi user mode.
Database QoEMetrics is set to multi user mode.
SQL Server Agent is running and its start mode was detected as Auto.
Executing QoEJobs.sql...
VERBOSE: Successfully installed the database. For details, see the following log:
"C:\Users\MK\AppData\Local\Temp\2\Create-MonitoringStore-HQ-LYNC2013-BE.MyDomain_mon-[2014_11_13][14_35_51].log"
VERBOSE: No changes were made to the Central Management Store.
VERBOSE: Creating new log file
"C:\Users\MK\AppData\Local\Temp\2\Install-CsDatabase-82d6613c-f2e3-47e6-8fc4-8f75d2efe6e4.html".
WARNING: "Install-CsDatabase" processing has completed with warnings. "5" warnings were recorded during this run.
WARNING: Detailed results can be found at
"C:\Users\MK\AppData\Local\Temp\2\Install-CsDatabase-82d6613c-f2e3-47e6-8fc4-8f75d2efe6e4.html".
PS C:\Users\MK>
I hope some one can confirm no issue with what I did ??
Kind Regards
MK

SPA9000 How do you direct SIP to FXS port?

How do you point a SIP account to the #1 FXS port on the SPA9000? I have a separate SIP account for my fax machine and need to point it to the analog FXS port.
Thanks

When you say “Line Tabs” do you mean where you configureLine 1-4? So if Line 1 is set for ITSP and Line 2 is the SPA400, I should useLine 3 for Fax? Then under ‘Line 3’ I should configure the User ID, Password,and Proxy like we did on the ITSP page except for the Fax SIP account?
Then change “Subscriber Information -> Contact list” to202. Then on the FXS 2 tab we should configure: User ID=202
Does this look correct?
What if we have two DID numbers associated with a single SIPaccount? Can we still direct one of the DID’s to the FXS 2 port?

Which Ports do MCU and Call Manager use for Video?

Hi, Does anyone know which ports the MCU and call Manager Use when using the 3511 MCU box with Call Manager 4.1.3. I am looking to open the appropriate ports on the firewall.
Regards
Dominic

Dominic,
If your MCU ports are Callmanger controlled, they will use Skinny (SCCP) to communicate on TCP port 2000. Please see the following link.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801a62b9.shtml
Hope this helps. If so, please rate the post.
Brandon

CLID not shown on FXS port

I am using Call-manager 6.0.1b, a MGCP controlled Gateway.On the Gateway i have installed a NM-HD-2V with a Vic2-2FXS module. On this module i connect 2 analog phone with capability to display the Caller-ID. When i call the analog port from a ip phone or from the other analog phone the Dn is not shown. When i connect the phone directly to the PSTN and dial this nr via my cell phone the nr is shown so i expect that the nr format received is not correct. How can this performed that the correct format is shown to the FXS port connected phone ?

Hi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick

CFwd on FXS-Ports (mgcp)

hi!
How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
How can I use the other Features, like PickUp etc.
vy Markus

Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.

FXS Ports & Pickup Groups

Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
Thanks in advance

Hi
You are going down the right track with this.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
Regards
Aaron
Please rate helpful posts...

Shared line appearance for FXS phones on SPA9000

Hello again!
(I hope asking these different questions in separate threads makes it easier.. not harder.)
If I'm using shared line appearance, can my FXS (regular cordless phones) pick up lines on hold? Can they put a line on hold? Is it easy?

I've never read or seen anything about SLA on the FXS ports.. but I guess you can always just try and see what happens. Configure one FXS port with the same userid as the shared line and see what happens if you put a call on hold. Since hook flash is used to put a call on hold / take it back, I figure if it worked, all it takes would be going off-hook and you'd have the call, and do a hook flash to put it back on hold.
There are two essential pieces to tracking down a problem with your VoIP equipment:
The configuration of every device involved
SIP protocol traces
And don't forget: there's no such thing as giving too much information when describing a problem.

Transfer called number from FSX port SPA8000 to FXO port analog PBX.

Hello all!
I have CUCM 8.6 which connecting with SPA8000 by SIP trunk.
FXS port SPA8000 connect to FXO port analog PBX.
When I call from CUCM to analog PBX through SPA8000, SPA8000 does not pass called number in line.
Anybody have ideas?

Here is what I would recomend, I have set this up at several installations and it works well. The only difference would be that the ones that I have setup had more than 64K between sites but that is still doable so long as you keep the traffic on that link well regulated.
Anyhow. At each site install a VIC-2FXO and a VIC-2FXS into your 1760. You can use the higer density modules if you need more paths. Tie the FXOs to analog station ports on your PBX and the FXSs to analog CO ports. This may seem backwards but it is correct. Cisco's FXS is expecting to provide dialtone and the analog CO ports on the PBX are expecting to receive dial tone. Depending on what you are using for call processing ITS/CCME/CCM configure your gateway and your route pattern, etc. You will also need to be able to somehow access those fxs ports for outbound calls. You could have direct line access buttons on your phones and instruct users that when calling the remote site the must use lines 7 and 8 as an example. You could also setup a line pool code for these new lines.
Now when site A wants to call Site B, they dial whatever you wish them to dial. You do whatever translations you may wish prior to sending the call. Here is how the call flow works. User at site A accesses the line either by hitting a line button or dialing the line pool code. This grabs the analog line tied to one of the FXs ports on the router. The call is then sent over the 64K link. The router at Site B then uses one of the FXO ports to pass the call to an analog station port on the other PBX. To the PBX at site B it will appear as though someone pickedu picked up an analog station and dialed a local extension.
Hope this helps. If you need any further clarification on this let me know and I will try to clear it up further for you.

SPA3102 FXS port

Hello,
I have a problem with my SPA3102's FXS port.
In last April I tested my friend's two PAP2T adapters with four phones. The adapters were connected to same switch with different fix IP addresses and phones were able to ring each other. Then I got one of adapters from him as a gift and on 2nd of January I bought an SPA3102 - so I have two adapters.
I connected my adapters to same switch. Their parameters are:
PAP2T IP: 192.168.0.221
FXS #1:
    SIP port: 5060
    display name: 1
    user ID: 1
FXS #2:
    SIP port: 5061
    display name: 2
    user ID: 2
SPA3102 IP: 192.168.0.222
FXS:
    SIP port: 5062
    display name: 3
    user ID: 3
Dialplans:
PAP2T Line1:        (<2:>S0 <:[email protected]:5061>|<3:>S0 <:[email protected]:5062>|<[x*]:>S0 <:[email protected]:5060>)
PAP2T Line2:        (<1:>S0 <:[email protected]:5060>|<3:>S0 <:[email protected]:5062>|<[x*]:>S0 <:[email protected]:5061>)
SPA3102 FXS:      (<1:>S0 <:[email protected]:5060>|<2:>S0 <:[email protected]:5061>|<[x*]:>S0 <:[email protected]:5062>)
Well there is problem with third phone (SPA3102 FXS port). Phones with PAP2T work perfectly, they can call each other. The 3rd phone has dialtone sometimes only but it is unable to call the other two phones. "1" and "2" can call third phone sometimes but another time I get reorder tone when I dial "3".
I have made backups from adapters' settings. Does somebody have any idea about this problem?
Thanks in advance,,,

Hi,
Problem is solved...
SPA3102 has two RJ45 outlets: LAN and WAN (internet). I have used LAN only because of switch and the INTERNET terminal was empty. It appears to me this situation drives SPA3102 crazy... I had to make a "loopback" plug (I linked contact 1 to contact 3 and contact 2 to contact 6) and insert it into INTERNET outlet. So all of phones work well...
If you want to use a PAP2T lonely (without internet access) as a "micro-PBX" with two extensions, you will have to use same plug otherwise phones won't work.

Call park using fxs port on spa9000

Similar Messages

Maybe you are looking for