Call Queue Software Options

                   Hello,
I have alot of customers in the medical field and have deployed UC500's pretty successfully.  Does anyone have any suggestions on call queue software that works with UC series really well.  The AA does a good job but if patients calling in get VM, the just call back and back, so I am looking for a solution where they wait in a queue, then are transfered to the first availble phone in a particular department, kind of what a call center does.  Thanks in advance for any suggestions.

Hi Mark,
One of the tricks I did to get the BACD to be a little more clever was to have its final destination point to the AA, then I set the AA prompts to do the following:
Announcement - "Thank you for continuing to hold, all our operators are currently busy so please choose from one of the following options" (Make this similar to the BACD Announcement)
1. Press "1" to continue to hold (This will send them back into the BACD)
2. If this is an emergency press "2" to speak to someone immediately otherwise dial (911 or 000 or what ever the emergency number is in your region) - Make sure this is pointing to a separate DN on each of the phones and mark it as the emergency extension
3. Or if you wish to be called back press "3" and leave a detailed voice mail and one of our staff will call you back shortly
This is the method I used for various medical center roll-outs, it worked quite well and in fact in some cases worked better than their previous system.
However, Please try and avoid doing this on a live system as it can be a little fiddly to setup, but once it is setup it does the job quite nicely
Cheers,
David Trad.
davidtradconsultinggmail.com

Similar Messages

  • Labview FPGA called another software component

    Hi
    I am trying to compile my FPGA code which has previously compiled. I get this error. 
    "Labview FPGA called another software component, and that component returned the following error:
    Error Code: -52009
    NI Platform Services: The requested resource has been marked for deletion and is rejecting new requests."
    What is this error code?

    Hi, 
    I've been looking in to this for you today - unfortunately, that seems to be a really rare error code which doesn't come up very often on our systems, so there's no quick fix that I can find.  
    A couple of options: 
    1) Have you made any changes to the code recently, in terms of updating it from an earlier version of LabVIEW? If so, it may be worth mass compiling your project up to the latest version in case there are references to software components which no longer exist.
    2) It's probably worth a try repairing your LabVIEW, FPGA and RIO drivers installations from disk, as described here: http://digital.ni.com/public.nsf/allkb/FE6B641E86E55AF2862576DE00038001?OpenDocument
    This could be due to some kind of missing or corrupted component in, for example, the Xilinx Tools
    3) Are you referencing any kind of external software, such as DLLs or third party instruments, in your file?
    4) What hardware are you using?
    Please let me know how you get on with these queries.
    Best wishes, 
    Chiara A
    Applications Engineer with NI UK & Ireland

  • BACD and hold times for Call Queue

    Hi Everyone,
    Is it possible to include hold times/wait times for BACD call queues?  Also, anyone run into issues when configuring BACD and the time it takes for it to ring in?  We had an issue previously that where the call would enter the queue, wait 30 seconds or so, and then ring out.  Unless this is normal.
    Thanks as always,
    HelpDesk

    Hi Help Desk,
    Its been a while since I configured this and I am not sure if the current versions of CCA allow for this change to take place.
    I know on the command line that this is possible, but ultimately it would be better to use CCA to make the changes as I am not sure if it would recognize the change if you did it via CLI.
    In the past as an alternative to hold times I did some work around's by pushing the BACD to an AA and putting in there some rudimentary options that would allow a user to go back into the line, but they would loose their position in doing so, but this shouldn't be a big problem.
    Also in terms of entering the BACD, I havent see the 30 second delay before so I am not sure what is going on there and I cannot say for that that it is normal operations for it.
    Cheers,
    David Trad.
    davidtradconsultinggmail.com

  • HT4623 My phone does not have the Update SOftware option between About & Usage in General under Settings. How do I update it then?

    My phone does not have the Update SOftware option between About & Usage in General under Settings. How do I update it then?

    This is called Support a Community of users who are helping each other. Save the sarcasm or smart remarks. I read must of your answers to other people as well and you seam to have a pattern like a bully. Sorry that our questions are above you. If you have no helping comments save them for yourself. READ what support means, you should try it once in awhile.

  • I'm new using Logic, i've been using garageband for quite awhile now though but my question is just basic. When i want to record electric guitar while clicking the software option it brings me to alot of guitar sounds that i want to chose. I chose the twa

    I'm new using Logic, i've been using garageband for quite awhile now though but my question is just basic. When i want to record electric guitar while clicking the software option it brings me to alot of guitar sounds that i want to chose. I chose the twangy electric or the distorted strat but i only hear clean sounds. No matter what kind of guitar sound i chose in the library it only produces clean guitar. How can i make it sound like it supposed to? Did i miss something i should do?

    This definitely has me stumped as I'm unsure as to why your guitar can be heard, but with none of the channel strips plugins applied to the sound.
    On the record enabled channel strip that contains your guitar input, is the "I" button located near the "R" active? Also, if you record your guitar, can you hear the FX applied to it when you play back the recorded track?

  • TS2795 When I set CALL FWDING  "ON" and I set the phone number and I back to CALL FWDING, the option returns to "OFF" status, why this is happening ?

    Hello,
    Can someone help me to activate the Call Forwarding option on IPhone 5, OS 6.01 ??
    Currently I am trying:
    * Settings -> Phone -> Call Forwarding -> "ON" -> SET THE PHONE NUMBER ->"Call Forwarding button"
    But when the screen returns to Call forwarding, the option returns to "OFF" mode.
    * I already try to call to *72 to "activate" the call forwarding option, just didn't work.
    I don't know if I need to do an additional configuration, If someone has an idea, please let me know!!
    Regards
    Cami

    Who is your carrier? Not all carriers support enabling and disabling call forwarding using the controls in Settings.

  • IPhoto/iDVD Slideshow Software Options?

    I have been unhappy with the resultant quality of slideshows that I have created in iPhoto and exported ('shared') with iDVD. The iPhoto quality is outstanding but I find significant quality degradation in iDVD in terms of clarity and smoothness of Ken Burns effect motion. This poor quality carries-over to the iDVD burned DVD-R.
    Does anyone have recommendations for alternate slideshow software options that produce clear, crisp and smooth motion slideshow DVDs?
    Message was edited by: MikeyM

    Have you asked over in the iDVD forum also? Any DVD authoring program will not be as sharp as what you see in iPhoto or on your computer because all media is reduced to 720 x 540 pixels. The same goes for videos. Smaller videos are scaled up and that's where you can lose image quality.
    The two links below are to Apple KB documents on preparing stills and videos for iDVD.
    http://docs.info.apple.com/article.html?path=iDVD/7.0/en/6732.html
    http://docs.info.apple.com/article.html?path=iDVD/7.0/en/6675.html
    Photo to Movie has received good reports in this forum. When using the KB effect you need to use the largest image available. Not so much with just still photos. As far as videos with motion you did use the Professional Quality setting, right?
    In finishing up the iDVD project are you saving it as a disk image first? Then you can check the encoding by playing it with DVD Player before burning. Burn to disc with Disk Utility at the slowest speed available to assure the best burn quality. Always use top quality media: Verbatium, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.
    OT

  • I need help in getting my software options in CS5 Photoshop Student version. We have registered the product but don't have print preview or Adjust Auto Levels for example?

    I need help in getting my software options in CS5 Photoshop Student version. We have registered the product but don't have print preview or Adjust Auto Levels for example?

    <moved from Downloading, Installing, Setting Up to Photoshop General Discussion>

  • Receiving IDocs in XI from a system with Queue Processing option

    I am trying to use the Queue Processing option that can be set in a partner profile for IDoc sending, so that qRFC is used.
    I have set up the Rule Name as one of the defaults that come with the system, but when I execute the sending of the IDoc, it gets stuck with status 30 (ready for dispatch). I have configured the Output Mode of the IDoc as "Transfer IDoc Immediately".
    SAP Documentation states that:
    "When you send by qRFC, the IDocs are first put in an outbound queue in the sending system, and then in an inbound queue in the recipient system. You can assign IDocs to various queues and specify queue name rules. "
    Is there something I also have to do in the XI system that is receiving the IDoc?
    Kind Regards,
    Tony.

    Hi Anthony,
    Now I have the same problem in between ECC6.0 and PI7.11.
    If you solving  the problem,
    Please let us know how you did.
    Best Regards,

  • Call Accounting Software for CUCM

    Hey,
    Hey my company formerly used RSI Accounting solution with our CUCM Version 9 system, but we are looking to explore alternative third party solutions. The new call accounting software should be:
    1)A Cisco Certified Developer Partner or Preferred Solution
    2) Compatible with all versions of CUCM( 7x-10x)
    3) Has ability to generate rich informative summary call cost reports
    4) We have multiple phone carriers and we need the software to be able to customize the call tariff rates to mirror as close as possible our local tariffs to be able to have accurate call costing
    5) The software provider must have good technical support in case of problems during installation or normal operation.
    6) send email alerts if any user is abusing company phone calls and be able to identify toll fraud events or prank calling
    Can anyone suggest any Cisco Partner party who satisfies the above criteria. I would appreciate any feedback.Thanks.
    Regards,
    Ryan Gosine

    Hi,
    With my company MAF InfoCom we provide solutions to capture, process and rate CDR’s from Cisco platforms.
    Our Call Management, Call Accounting and Telecom Expense Management solutions are very user friendly and cost effective.
    If you need more information please reach out to me via our website www.mafinfo.com
    Frank Looijesteijn

  • HT4623 I am trying to update my iPad to iOS6 but there is no update software option on the general screen

    I am trying to update my iPad to iOS 6 but there is no update software option under general settings..please help me. Also I can not get it to connect to wireless service at home but it will other places.

    Connect your iPad to iTune (computer) and Check for Updates. Backup before you proceed with update.
    http://i1224.photobucket.com/albums/ee374/Diavonex/Album%201/e0f22e92de98ebae10e 3fd537c16619e.jpg

  • HT4623 I do not see the software option in my general settings, how can I resolve this? I need to update to the ios5

    I need to update my operating system, but when I go into settings and then general I do not have the software option even available. What can I do? Aim not sure what operating system I'm currently working with I know it is not the iOS 5 or newer.

    You'll need to connect the iPad to a computer running iTunes. Then update through that.
    The following link has the ste by step guide. Just scroll down to the section titled Update your device using iTunes
    http://support.apple.com/kb/HT4623
    to find out which iOS version you are rtunning, you can go into settings->General->About and lok for the section titled "Version"

  • BE6000 Native Call Queuing Design Constraints?

    We see the doc wiki has not been updated with any UCM 9.0 native call queuing design constraints.  We would assume that the call queuing at a min would need to meet the MoH design constraint of 50 sessions, since you figure there is a high probability that one call will be queued in each of 50 queues with MoH playing with each.
    http://docwiki.cisco.com/wiki/Supported_System_Capacities
    Is there any other performance impact we should consider or can we ask the doc wiki be updated with design constraints around call queuing?
    Can the BU clarify is that is 50 simultanous MoH streams per cluster, or 50 per server?  We can eliminate the load by going to multicast and IOS distributed MoH for remote sites, but something tells me there probably is a max queued call ceiling we need to consider for this platform.

    At the risk of getting caught up in the pass-by-reference/pass-by-value debate :), simple values (ints chars etc). are passed as values, and modifying them on the C++ side of the procedure call will not modify the values on th java side.
    Possible solutions are:
    1)pass an array of (say) ints. Then, modifying individual values should modify the java-side values (much in the way that the Stream.read(byte[]) functions do.
    2)format up a strin g with your return values, return the string and parse it on the java side.
    3)have fields in the java side that are accessed and modified by your native call.
    4)pass an object with some fields in it. Have the C++ access and modify the object's fields.
    Hope this helps.

  • HT4623 I do not have the Software option on my ipod

    I am trying to update my ipod touch, i went to settings, general and i do not have the software option. What does this mean?

    That is only a feature of iOS 5 or later...
    You have iOS 4... See Here...
    http://support.apple.com/kb/HT4972
    OR...
    Connect to iTunes on the computer you usually Sync with and “ Check for Updates “...
    If an Update Appears Install it... if not... you are up to date for your particular Device...
    See the Using iTunes Section Here...
    How to update your iPhone, iPad, or iPod touch

  • HT4623 I don't have a 'software' option under settings, general....how do I update to 4.03 or newer?

    I need to update my Iphone 4 to @ least i4.03 so that I can install instgram....when I go to settings/general....there is no software option...how do I acquire software updates?

    Correct; you need at least iOS 5 to have a software update option on your iPhone.
    Your only option is to connect your iPhone to iTunes and, once synced, do a "Check for Update" on the right side in iTunes' summary tab.

Maybe you are looking for