Call Rejected error when Using CTI Port to call out
Hello,
I am using Cisco Call Recording feature that is enabled on a phone that has a CTI Port and number assigned to invoke a call recording session to dial out a Long Distance number. I used JTAPI tool to invoke a call and then used the CTI that was invoked by the BIB to dial a long distance number. The call leaves the phone and gets to the gateway (MGCP) with 2 T1 Pri's and in the debug I see this error:
KNOW Good call:
001679: *Sep 20 14:39:53.005: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x5069
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18395
Preferred, Channel 21
Facility i = 0x9F8B0100A1080201010201008400
Protocol Profile = Networking Extensions
0xA1080201010201008400
Component = Invoke component
Invoke Id = 1
Operation = CallingName
Name not available
Calling Party Number i = 0x0080, 'XXXXXXXXX'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, 'XXXXXXXXXX'
Plan:Unknown, Type:Unknown
001680: *Sep 20 14:39:53.009: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xD069
Cause i = 0x8081 - Unallocated/unassigned number
001681: *Sep 20 14:39:53.097: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x506A
FAILED Call:
001685: *Sep 20 14:39:56.509: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x1DA8
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98384
Exclusive, Channel 4
Calling Party Number i = 0x0183, '2678'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x80, 'XXXXXXXXXXX'
Plan:Unknown, Type:Unknown
001686: *Sep 20 14:39:56.537: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x9DA8
Channel ID i = 0xA98384
Exclusive, Channel 4
001687: *Sep 20 14:39:56.557: ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x9DA8
Cause i = 0x8295 - Call rejected
001688: *Sep 20 14:39:56.585: ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x1DA8
001689: *Sep 20 14:39:56.593: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x9DA8
001690: *Sep 20 14:40:07.001: ISDN Se0/0/1:23 Q931: RX <- SETUP pd = 8 callref = 0x4200
Anyhelp appreciated.
Hi,
I have looked into the issue. If you are trying to create the BP with general role 000000, i think it might not be possible via LSMW.
The error message is correct, because role 000000 is indeed not relevant for update because if you can see in the customising Tx BUSD, 'FLAG - Do not update' will be active. This is the reason why you are getting the error message of 'No update is defined for the role 000000'.
When you insert a partner in role "000000 General Business Partner",the error message "BP role cannot be updated" will be returned. This error message is very specific for this issue. You can create BP in different roles apart from the general role.
Indeed if you try to change the 'Do not update' flag to inactive state and process the LSMW project you will be able to create the BP but it is strictly not recommended.
This role is a technical role which exists for the creation of BP, and immediately you will fall back to other roles available for the partner.
So i feel you need to change the role before you create BP with this role via LSMW.
I hope this helps.
Regards,
Venkat
Similar Messages
-
LabVIEW PDA reports COREDLL.DLL error when using Call Library Function Node
I'm trying to build a LV PDA app that calls an external DLL file built using embedded visual C. When configuring the Call Library Function node I select the stub DLL, configure the I/O parameters and select OK. When the configuration dialog closes I get the following error:
LabVIEW: LabVIEW.exe - Unable to Locate Component
This application has failed to start because COREDLL.DLL was not found. Re-installing the application may fix this problem.
I do not get this error when using the configuration dialog in the example VIs.
Any suggestions as to the cause and/or the solution?
Thanks,
RyanHello -
When you create a PDA VI that calls a DLL, you must include the .c or .lib file that corresponds to the DLL. Take a look at these documents:
LabVIEW PDA Module Build Errors with VIs that Call DLLs
Why Do I Receive Errors When Calling a C++ DLL from a Call Library Node Using the LabVIEW PDA Module...
How To Call External Code in LabVIEW PDA for Palm OS
H
ow To Call External Code in LabVIEW PDA for Pocket PC
Hope this helps!
S Vences
Applications Engineer
National Instruments -
Error when using PPR in the OA page developed.
HI,
We are encountering an error when using PPR for the custom OA page being developed. I am using JDeveloper version 9.0.3.5(Build 1437) and Oracle Applications version 11.5.10.CU2. The scenario we are using PPR and the steps to reproduce the issue is mentioned below,
Scenario:
1) PPR is enabled for a custom OA page that is developed.
2) The PPR is being used to enable or disable a particular field based on the
selection of a value in a poplist in the same OA Page.
Error replication steps:
1) The user enters a value in the primary mandatory field which has to have
unique value.
2) The user selects a value from the poplist of a field which has PPR associated.
3) The user enters data in all other mandatory fields in the OA page except one
and tries to save the form and is shown a error message saying that all
mandatory fields are not entered(This is correct). Now the page gets
automatically refreshed and so the entered values are wiped off.
4) Now if the user again enters a value in the primary mandatory field (as in
step1) and if that value happens to be already existing value and then select
a value from the poplist which has PPR enabled then immediately the error
"Please enter a unique value" is entered, though we did not save the record.
The unique record validation would happen only at the time of saving the
record as per out business logic.
5) But if in Step 4 if i had entered a unique value again then the above said error
does not happen. There are few more similar kind of issues happening in the
same page because PPR is enabled.
Please note that this issue happens only when the page is deployed in a oracle
applications instance and not in JDeveloper.
Would this issue because of some cacheing problem? If Yes then how do we resolve it? Or would it be some other problem caused by our internal coding.
Any inputs for resolving this issue would be highly appreciated.
Thanks, Raja.What works in Jdeveloper should work when deployed in iAS as well.
And PPR is an old feature given quite enough time to mature, so before we suspect OA we should investigate the code. What I do not understand is how the page refreshes in Step 3 and why does the user have to re-enter the fields just because he missed entering one mandatory field the last time.
Mandatory field validations are client validations set by making the fields 'Required'. You obviously have client validations turned off on your PPR, otherwise you would be stuck with a javascript popup on PPR. The only way you can get the "Please enter unique..." error on PPR is Server Validation. So where have you placed this validation? If it is not in the EO, is it in the AM? And are you unconditionally calling the AM validation method in your processFormRequest? The PPR will also go through processFormRequest so I hope the PPR event is in a different if-else block. -
UDESEncrypt Errors when using the JAVA engine (NW IDM 7.0)
Folks,
I'm seeing an error when I use the uDESEncrypt function with the Java Engine in NW IDM SP2 Patch 3.
The error I am getting is:
runFunctionsInString($FUNCTION.encrPWD()$$) got exception
org.mozilla.javascript.EvaluatorException: uDESEncrypt: Key should be exactly 24 bytes long.
The code calling it is:
// Main function: encrPWD
function encrPWD(Par){
//Example calling DSE internal function
//UserFunc.uStop("Terminated by user");
key = "C:\Program Files\SAP\IdM\Workflow\configs\KEY\keys.ini";
OutString = UserFunc.uDESEncrypt(key, Par);
return OutString;
I have also seen this error when using Patch 4.
Interestingly enough, the error does not occur when using the Windows Engine. Anyone else seeing this?
Thanks,
MattHi Matthew,
Try to replace the '\' with '
key = "C:
Program Files
SAP
IdM
Workflow
configs
KEY
keys.ini";
Alternative approaches,
1) setting key empty and it will look into %DSE_HOME%\KEY\key.ini
which should be C:\Program Files\SAP\IdM\Identity Center\Key\key.ini on default installation path.
2) or setting the key to something like = 6D5A2AF59B1CDD7F9592484F178331C891537A3F9B91D362
a 24 byte key...
Also when using DES you should ensure that in Identity Center underneath Options/General
you have encryption algorithm set to 3DES.
Normally if you intend to use this for password provisioning in IC you would also
on the identity store (for instance 'Enterprise people') underneath 'password policy' check
of for 'enable password provisioning.'
By doing so the MX_ENCRYPTED_PASSWORD with be set when operating through
workflow (3DES encryption version of the MX_PASSWORD) which allows you to obtain password
when provisioning to other target systems... -
Any help will be greatly appreciated.
I got the following errors when using the ant task source2wsdd:
[source2wsdd] classpath C:\bea\weblogic81\server\lib\weblogic.jar;C:\bea\weblogi
c81\server\lib\webservices.jar
[source2wsdd] source2wsdd: Cannot find doclet class weblogic.webservice.tools.dd
gen.ServiceGen
[source2wsdd] 1 error
[ant] Exiting C:\project\DCII\ant\batch-build.xml.
BUILD FAILED
C:\project\ant\build.xml:67: The following error occurred while executing this l
ine:
C:\project\DCII\ant\batch-build.xml:326: javadoc execution failed
at org.apache.tools.ant.ProjectHelper.addLocationToBuildException(Projec
tHelper.java:539)
at org.apache.tools.ant.taskdefs.Ant.execute(Ant.java:388)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at org.apache.tools.ant.Project.executeTargets(Project.java:1062)
at org.apache.tools.ant.Main.runBuild(Main.java:673)
at org.apache.tools.ant.Main.startAnt(Main.java:188)
at org.apache.tools.ant.launch.Launcher.run(Launcher.java:196)
at org.apache.tools.ant.launch.Launcher.main(Launcher.java:55)
Caused by: C:\project\DCII\ant\batch-build.xml:326: javadoc execution failed
at weblogic.ant.taskdefs.webservices.autotype.JavaSource2DD.runJavadoc(J
avaSource2DD.java:297)
at weblogic.ant.taskdefs.webservices.autotype.JavaSource2DD.execute(Java
Source2DD.java:150)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at ise.antelope.tasks.Call.execute(Call.java:17)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at ise.antelope.tasks.IfTask.doIf(IfTask.java:298)
at ise.antelope.tasks.IfTask.execute(IfTask.java:267)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at org.apache.tools.ant.taskdefs.Ant.execute(Ant.java:386)
... 10 more
--- Nested Exception ---
C:\project\DCII\ant\batch-build.xml:326: javadoc execution failed
at weblogic.ant.taskdefs.webservices.autotype.JavaSource2DD.runJavadoc(J
avaSource2DD.java:297)
at weblogic.ant.taskdefs.webservices.autotype.JavaSource2DD.execute(Java
Source2DD.java:150)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at ise.antelope.tasks.Call.execute(Call.java:17)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at ise.antelope.tasks.IfTask.doIf(IfTask.java:298)
at ise.antelope.tasks.IfTask.execute(IfTask.java:267)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at org.apache.tools.ant.taskdefs.Ant.execute(Ant.java:386)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at org.apache.tools.ant.Project.executeTargets(Project.java:1062)
at org.apache.tools.ant.Main.runBuild(Main.java:673)
at org.apache.tools.ant.Main.startAnt(Main.java:188)
at org.apache.tools.ant.launch.Launcher.run(Launcher.java:196)
at org.apache.tools.ant.launch.Launcher.main(Launcher.java:55)
Total time: 8 seconds
The following is the major parts from my ant build file:
<path id="webservice.classpath">
<pathelement location="${wls.home.dir}/server/lib/weblogic.jar"/>
<pathelement location="${wls.home.dir}/server/lib/webservices.jar"/>
</path>
<target name = "initialize">
<mkdir dir="${build.dir}"/>
<mkdir dir="${class.dir}"/>
<mkdir dir="${dist.dir}/${deploy.env}"/>
<mkdir dir="${jdocs.dir}"/>
<mkdir dir="${weblogic.application.dir}"/>
<taskdef name="call"
classpathref="antelope.classpath"
classname="ise.antelope.tasks.Call"/>
<taskdef name="if"
classpathref="antelope.classpath"
classname="ise.antelope.tasks.IfTask"/>
<taskdef name="servicegen"
classpathref="webservice.classpath"
classname="weblogic.ant.taskdefs.webservices.servicegen.ServiceGenTask"/>
<taskdef name="clientgen"
classpathref="webservice.classpath"
classname="weblogic.ant.taskdefs.webservices.clientgen.ClientGenTask"/>
<taskdef name="source2wsdd"
classpathref="webservice.classpath"
classname="weblogic.ant.taskdefs.webservices.autotype.JavaSource2DD"/>
<taskdef name="wldeploy"
classpathref="webservice.classpath"
classname="weblogic.ant.taskdefs.management.WLDeploy"/>
</target>
<target name="buildEar"
depends="buildCommonJar, ejbc">
<echo message ="[${module.name}] Checking to see if ${ear.file} is up to date...[${appc.classpath}]" />
<source2wsdd
javaSource="${webserviceServer_src_dir}/HelloWorld.java"
ddFile="${descriptor.dir}/webservice/web-services.xml"
serviceUri="/HelloWorld">
<classpath refid="webservice.classpath" />
</source2wsdd>
<echo message ="[Done with buildEar]" />
</target>Did you ever resolve this?
-
Error When Using Class :(
Hey,
Class:
package
import flash.display.MovieClip;
import flash.events.Event;
public class Main extends MovieClip
public var enemyA:Array = [];
public var birdA:Array = [];
public var rowNum:int = 2;
private var gap:int = 100;
private var obj_no = 2;
public var enemy1:mychar = new mychar();
public var TheBird:BirdChar = new BirdChar();
public function Main()
// constructor code
createEnemyF();
createBirdF();
this.addEventListener(Event.ENTER_FRAME,loopF);
public function createEnemyF()
for (var i:int = 0; i < rowNum; i++)
for (var j:int = 0; j < obj_no; j++)
enemy1.x = Math.random() * stage.stageWidth - enemy1.width;
enemy1.y = - i * (gap + enemy1.height) - 30.65;
enemyA.push(enemy1);
addChild(enemy1);
public function createBirdF() {
TheBird.x = 270.95;
TheBird.y = 350.95;
birdA.push(TheBird);
addChild(TheBird);
public function loopF(event:Event) {
updateEnemyPositionsF();
updateBirdPositionsF();
hitTestF();
public function updateEnemyPositionsF() {
enemy1.y += 2;
public function updateBirdPositionsF() {
TheBird.x = mouseX;
public function hitTestF() {
if(TheBird.hitTestObject(enemy1))
gotoAndPlay(5);
trace('The Bird Hit Enemy 1');
This conflicts and causes this error:
1046: Type was not found or was not a compile-time constant: MouseEvent
^ ^ Code repeats to all of my event listeners
Thanks for your time.Thanks, i thought it might be this because of previous problems but i seen i already had : import flash.events.Event; so i thought that would be OK!
Second Error:
1180: Call to an undefined method Timer.
I think this is the same sort of thing but what to import to fix this?
So far these are my imports:
import flash.display.MovieClip;
import flash.events.Event;
import flash.events.MouseEvent;
import flash.events.TimerEvent;
Thanks for helping.
Date: Thu, 3 Nov 2011 05:36:22 -0600
From: [email protected]
To: [email protected]
Subject: Error When Using Class
Re: Error When Using Class
created by markerline in Flash Pro - General - View the full discussion
Looks like you imported events.Event but not events.MouseEvent (or some similar syntax) basically you must import MouseEvents separately from other Events.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4005227#4005227
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4005227#4005227. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Flash Pro - General by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
Compilation error when used SET or MULTISET operator on nested tables
Dear All,
I am getting Compilation error when used SET or MULTISET operator on nested tables inside a procedure.
This is working fine in other DB installations of 10g but does not work in another 10g DB.
it says "wrong number of parameter or datatype used in SET"
Can any one suggest what went wrong here?
Thanks in advance.Hi,
Thanks for ur reply...
Since MULTISET and SET operators are the new additions in base 10g release for manipulation of nested tables data, I am surprised that same is working in similar 5 DBs installations with 10.2.0.1.0 version, but does not work in the sixth.
SET and MULTISET operators are used inside the PL/SQL procedure which is getting compiled in the above mentioned 5 DBs but not in sixth DB.
it gives
On line: 3112
PLS-00306: wrong number or types of arguments in call to 'SET'
Hope this clarifies the issue... -
Photoshop CS4 "Program Error" when using Text tool
Hello. I was having problems with Photoshop displaying a "Program Error" every so often, so I deleted the preference file and all seemed good. But after deleting the preference file for my Photoshop CS4 and re-launching Photoshop, the text tool causes Photoshop to display a Program Error when using the tool. It never did this before. Should I reinstall Photoshop? I am using a Powermac G5 running 10.5.8. I have already tried repairing the disk permissions.
ThanksThats kinda what I thought too, but the problem started happening randomly. It started when we were trying to use photomerge with large photos. The program just started giving the program errors. I still think it may be a font problem, but without going through my 2000+ fonts and disabling them one by one, how can I resolve this issue?
Thanks -
Using just the TV screen when using HDMI port?
Hi,
I have the Macbook Pro with retina display and I was wondering how I could use just the TV screen when using HDMI port. I don't want mirroring displays, just one on the TV.With the TV connected and the MBP plugged into the mains (i.e. not running on battery power) close the lid. The MBP will go to sleep, wake it up with an external keyboard or mouse - which must be connected in advance, or paired in advance if a bluetooth keyboard/mouse.
-
Java Heap Error when using Stateless Session Timer Bean deployed in Oracle
Hi,
Am getting following Java Heap Error when using Stateless Session Timer Bean deployed in Oracle 10g AS R3 (Oracle Containers for J2EE 10g (10.1.3.0.0) (build 060119.1546.05277) ):
06/08/02 14:58:43 javax.ejb.EJBException: java.lang.OutOfMemoryError: Java heap space
06/08/02 14:58:43 at com.evermind.server.ejb.EJBUtils.getLocalUserException(EJBUtils.java:304)
06/08/02 14:58:43 at com.evermind.server.ejb.interceptor.system.AbstractTxInterceptor.convertAndHandleMethodException(AbstractTxInterceptor.java:67)
06/08/02 14:58:43 at com.evermind.server.ejb.interceptor.system.TxNotSupportedInterceptor.invoke(TxNotSupportedInterceptor.java:45)
06/08/02 14:58:43 at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:69)
06/08/02 14:58:43 at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:86)
06/08/02 14:58:43 at com.evermind.server.ejb.StatelessSessionEJBHome.invokeTimer(StatelessSessionEJBHome.java:71)
06/08/02 14:58:43 at com.evermind.server.ejb.EJBContainer.invokeTimer(EJBContainer.java:1624)
06/08/02 14:58:43 at oracle.ias.container.scheduler.TimerTask.runBeanTimer(TimerTask.java:92)
06/08/02 14:58:43 at oracle.ias.container.scheduler.TimerTask.run(TimerTask.java:184)
06/08/02 14:58:43 at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:819)
06/08/02 14:58:43 at java.lang.Thread.run(Thread.java:595)
06/08/02 14:58:43 Caused by: java.lang.OutOfMemoryError: Java heap space
I had tried using -Xms / -Xmx options (upto 1 GB).
The trace of exception gets delayed (from being displayed on the console) as the memory size is increased; but after sometime it starts getting displayed on the console.
Even though this exception is displayed on the console, the Timer Bean continues to execute upto sometime before it finally crashes!
If anyone has encountered such problem; would appreciate if you could share the solution.
Regards, VidyadharHi guys, I have the same problem. I have an application EAR file with two modules (EJB and WAR starting in this order). The application can schedule a process via EJB timer. In this case restarting the server I receive the error above. If I change the modules start order --> WAR - EJB the server start correctly, but the application scheduler fails (the persistency is not working) with this error:
07/10/09 10:30:54 FINISSIMO: TimerTask.runBeanTimer java.lang.NullPointerException; nested exception is: java.lang.NullPointerExceptionjavax.ejb.TransactionRolledbackLocalException: java.lang.NullPointerException; nested exception is: java.lang.NullPointerException
java.lang.NullPointerException
at java.util.ListResourceBundle.handleGetObject(ListResourceBundle.java:107)
at java.util.ResourceBundle.getObject(ResourceBundle.java:319)
at java.util.ResourceBundle.getString(ResourceBundle.java:285)
at java.util.logging.Formatter.formatMessage(Formatter.java:108)
at oracle.j2ee.util.TraceLogFormatter.format(TraceLogger.java:124)
at oracle.j2ee.util.TraceLogger$TraceLoggerHandler.publish(TraceLogger.java:105)
at java.util.logging.Logger.log(Logger.java:428)
at java.util.logging.Logger.doLog(Logger.java:450)
at java.util.logging.Logger.log(Logger.java:539)
at oracle.ias.container.timer.TimerEntry.readObjFromBytes(TimerEntry.java:308)
at oracle.ias.container.timer.TimerEntry.getInfo(TimerEntry.java:107)
at oracle.ias.container.timer.Timer.getInfo(Timer.java:367)
at oracle.ias.container.timer.EJBTimerImpl.getInfo(EJBTimerImpl.java:89)
at com.finantix.foundation.integration.ejbtimer.EJBTimerServiceExecutorBean.ejbTimeout(EJBTimerServiceExecutorBean.java:42)
at com.evermind.server.ejb.interceptor.joinpoint.EJBTimeoutJoinPoint.invoke(EJBTimeoutJoinPoint.java:20)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.SetContextActionInterceptor.invoke(SetContextActionInterceptor.java:44)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.TxBeanManagedInterceptor.invoke(TxBeanManagedInterceptor.java:53)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:87)
at com.evermind.server.ejb.StatelessSessionEJBHome.invokeTimer(StatelessSessionEJBHome.java:38)
at com.evermind.server.ejb.EJBContainer.invokeTimer(EJBContainer.java:1714)
at oracle.ias.container.scheduler.TimerTask.runBeanTimer(TimerTask.java:106)
at oracle.ias.container.scheduler.TimerTask.run(TimerTask.java:220)
at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
at java.lang.Thread.run(Thread.java:595)
javax.ejb.TransactionRolledbackLocalException: java.lang.NullPointerException; nested exception is: java.lang.NullPointerException
at com.evermind.server.ejb.EJBUtils.getLocalUserException(EJBUtils.java:309)
at com.evermind.server.ejb.interceptor.system.AbstractTxInterceptor.convertAndHandleMethodException(AbstractTxInterceptor.java:73)
at com.evermind.server.ejb.interceptor.system.TxBeanManagedInterceptor.invoke(TxBeanManagedInterceptor.java:55)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:87)
at com.evermind.server.ejb.StatelessSessionEJBHome.invokeTimer(StatelessSessionEJBHome.java:38)
at com.evermind.server.ejb.EJBContainer.invokeTimer(EJBContainer.java:1714)
at oracle.ias.container.scheduler.TimerTask.runBeanTimer(TimerTask.java:106)
at oracle.ias.container.scheduler.TimerTask.run(TimerTask.java:220)
at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
at java.lang.Thread.run(Thread.java:595)
Caused by: java.lang.NullPointerException
at java.util.ListResourceBundle.handleGetObject(ListResourceBundle.java:107)
at java.util.ResourceBundle.getObject(ResourceBundle.java:319)
at java.util.ResourceBundle.getString(ResourceBundle.java:285)
at java.util.logging.Formatter.formatMessage(Formatter.java:108)
at oracle.j2ee.util.TraceLogFormatter.format(TraceLogger.java:124)
at oracle.j2ee.util.TraceLogger$TraceLoggerHandler.publish(TraceLogger.java:105)
at java.util.logging.Logger.log(Logger.java:428)
at java.util.logging.Logger.doLog(Logger.java:450)
at java.util.logging.Logger.log(Logger.java:539)
at oracle.ias.container.timer.TimerEntry.readObjFromBytes(TimerEntry.java:308)
at oracle.ias.container.timer.TimerEntry.getInfo(TimerEntry.java:107)
at oracle.ias.container.timer.Timer.getInfo(Timer.java:367)
at oracle.ias.container.timer.EJBTimerImpl.getInfo(EJBTimerImpl.java:89)
at com.finantix.foundation.integration.ejbtimer.EJBTimerServiceExecutorBean.ejbTimeout(EJBTimerServiceExecutorBean.java:42)
at com.evermind.server.ejb.interceptor.joinpoint.EJBTimeoutJoinPoint.invoke(EJBTimeoutJoinPoint.java:20)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.SetContextActionInterceptor.invoke(SetContextActionInterceptor.java:44)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.TxBeanManagedInterceptor.invoke(TxBeanManagedInterceptor.java:53)
... 9 more
Any idea?
Thx Auro -
Getting an error when using adobe photoshop CC, "Could not move the data because of a program error". Any idea on what this means?
Have no idea of what you were even doing in Photoshop my crystal ball is out for repairs so I can not see.
-
Multivalue error when using the previous() function
I am getting a multivalue error when using the previous() function on a dimension object in the report. I thought that the previous function was supposed to look at the current report and then look at the previous record's contents. How could this possibly give me a multivalue error when the value is clearly output in the previous row? Anyone have any ideas?
By the way, this is a valuable function for the types of reports that I design. The next() function would be even more valuable.
Thanks for your help.Hi Michael,
Could you please test the following solutions it might help you to resolve the issue.
Solution1:
Use slice and dice to reset all the tables that have #multivalue in it. The only problem with this workaround is they have to do the formatting manually.
Solution2:
Also, test the issue by changing the object to dimension if it is a measure or to measure if it is a dimension.
Regards,
Sarbhjeet Kaur -
Dbms_crypto - avoid error when using different key in lower environment
Hello Experts,
We are using Oracle 11.2.0.2. We are planning to implement dbms_crypto to encrypt few columns. We clone the data from production to lower environment ( DEV, QC).
For the lower environments, we do not want to get the sensitive data from production and do not plan to use same key. Rather than getting an error when using differnt key, is it possible to get a different resultset back.
In other words, we want the implementation to be same across environments but want to use a diffent key in lower environment and get different result (or garbage).
Any suggestions would be greatly appreciated.
While testing this logic, I am getting following error when using differnt key to decrypt. It works fine if I use same key.
Error at line 1
ORA-28817: PL/SQL function returned an error.
ORA-06512: at "SYS.DBMS_CRYPTO_FFI", line 67
ORA-06512: at "SYS.DBMS_CRYPTO", line 44
ORA-06512: at line 19
DECLARE
l_credit_card_no VARCHAR2(19) := '1234 5678 9012 3456';
l_ccn_raw RAW(128) := UTL_RAW.cast_to_raw(l_credit_card_no);
l_key RAW(128) := UTL_RAW.cast_to_raw('abcdefgh');
l2_key RAW(128) := UTL_RAW.cast_to_raw('12345678');
l_encrypted_raw RAW(2048);
l_decrypted_raw RAW(2048);
BEGIN
DBMS_OUTPUT.put_line('Original : ' || l_credit_card_no);
l_encrypted_raw := DBMS_CRYPTO.encrypt(src => l_ccn_raw,
typ => DBMS_CRYPTO.des_cbc_pkcs5,
key => l_key);
DBMS_OUTPUT.put_line('Encrypted : ' || RAWTOHEX(UTL_RAW.cast_to_raw(l_encrypted_raw)));
l_decrypted_raw := DBMS_CRYPTO.decrypt(src => l_encrypted_raw,
typ => DBMS_CRYPTO.des_cbc_pkcs5,
key => l2_key); --**Using different key to decrypt
DBMS_OUTPUT.put_line('Decrypted : ' || UTL_RAW.cast_to_varchar2(l_decrypted_raw));
END;Thank you.If I understand what you are trying to do ... and I may not ... it is not going to work.
SQL> DECLARE
2 l_credit_card_no VARCHAR2(19) := '1612-1791-1809-2605';
3 l_ccn_raw RAW(128) := utl_raw.cast_to_raw(l_credit_card_no);
4 l_key1 RAW(128) := utl_raw.cast_to_raw('abcdefgh');
5 l_key2 RAW(128) := utl_raw.cast_to_raw('zyxwvuts'); -- alternate key used to attempt a different decryption
6
7 l_encrypted_raw RAW(2048);
8 l_decrypted_raw RAW(2048);
9 BEGIN
10 dbms_output.put_line('Original : ' || l_credit_card_no);
11
12 l_encrypted_raw := dbms_crypto.encrypt(l_ccn_raw, dbms_crypto.des_cbc_pkcs5, l_key1);
13
14 dbms_output.put_line('Encrypted : ' || RAWTOHEX(utl_raw.cast_to_raw(l_encrypted_raw)));
15
16 l_decrypted_raw := dbms_crypto.decrypt(src => l_encrypted_raw, typ => dbms_crypto.des_cbc_pkc
s5, key => l_key1);
17
18 dbms_output.put_line('Key1 : ' || utl_raw.cast_to_varchar2(l_decrypted_raw));
19
20 l_decrypted_raw := dbms_crypto.decrypt(src => l_encrypted_raw, typ => dbms_crypto.des_cbc_pkc
s5, key => l_key2);
21
22 dbms_output.put_line('Key2 : ' || utl_raw.cast_to_varchar2(l_decrypted_raw));
23 END;
24 /
Original : 1612-1791-1809-2605
Encrypted : 3534443342333642353141363846384237463732384636373943374630364234323243334539383042323135
Key1 : 1612-1791-1809-2605
DECLARE
ERROR at line 1:
ORA-28817: PL/SQL function returned an error.
ORA-06512: at "SYS.DBMS_CRYPTO_FFI", line 67
ORA-06512: at "SYS.DBMS_CRYPTO", line 44
ORA-06512: at line 20 -
Error when using Oracle Migration WorkBench (Sql Server 2k to Oracle 8i)
I'm trying to migrate a Sql Server 2k database to an Oracle 8i schema using OMWB. After using BCP to collect metadata information on the source database, I tried to capture the source data model and got a "Capture aborted" message on the progress screen (even though then it appears a dialog window reporting "0 errors and 0 warnings", funny!). Down there is the error log OMWB generated. After reading some posts, I changed some columns of the OMWB dictionary that holds the source database name, but still got the same error. If someone can enlighten me on this toppic, I'd greatly appreciated it.
Here's the error log of OMWB:
** Oracle Migration Workbench
** Production
** ( Build 20050629 )
** OMWB_HOME: D:\Datos\Download\Oracle\Oracle Migration Workbench\omwb
** user language: es
** user region: null
** user timezone:
** file encoding: Cp1252
** java version: 1.4.2_04
** java vendor: Sun Microsystems Inc.
** o.s. arch: x86
** o.s. name: Windows 2000
** o.s. version: 5.0
** Classpath:
..\lib\boot.jar
** Started : Fri Feb 23 17:18:48 GMT-03:00 2007
** Workbench Repository : Oracle8i Enterprise Edition Release 8.1.6.0.0 - Production
With the Partitioning option
JServer Release 8.1.6.0.0 - Production
Repository Connection URL: jdbc:oracle:thin:@ServerCms:1521:sigcewbc
** The following plugins are installed:
** Microsoft Access 2.0/95/97/2000/2002/2003 Plugin, Production Release 10.1.0.4.0
** Microsoft SQLServer 2000 Plugin, Production Release 10.1.0.4.0
** Microsoft SQLServer 6.5 Plugin, Production Release 10.1.0.4.0
** Microsoft SQLServer 7.0 Plugin, Production Release 10.1.0.4.0
** Active Plugin : SQLServer2K
EXCEPTION :SQLServer2KDisconnSourceModelLoad.loadSourceModel(): oracle.mtg.migration.MigrationStopException: java.lang.IndexOutOfBoundsException: Index: 15, Size: 15
** Shutdown : Fri Feb 23 18:00:50 GMT-03:00 2007Duplicate thread
Error when using Oracle Migration WorkBench (Sql Server 2k to Oracle 8i) -
ABAP Runtime error when using RSPC
Hi Team,
I am getting ABAP runtime error when using RSPC in my system.For the same user id in other systems this transaction is working fine.Pls help me.
regds
ShaHello Sha Han,
What is the runtime error you are getting?
Please check the authorization also for the user in that system
Thanks
Chandran
Maybe you are looking for
-
I have Norton Internet Security. When I downloaded the new FF4 they said that a part of Norton wasn't compatible - and it seems that that part must have been my Identity Safe which holds all my password info & fills in all of my passwords for me. You
-
Moving Pictures to new drive- XP MC/LR 1.1
What if I want to move the photos that have been imported at their location? IOW, I am on Windows XP MC, I have imported lots of photos (7000+) and have either brought them from their location in {c:\documents and settings\.....} ...My Documents\My P
-
Selection screen problem in module pool
Hi friends, I am working on module pool programming, I need to put select screen on the screen of the module pool porgramming. I used Input/Output field to do that and activated. But I am getting message invalid field format (screen error) can any on
-
To grant execute on a specific procedure in a package
is there a way to grant execute on a specific procedure in a package without granting execute to the package itself.
-
Complete Form approval step programatically
Hi, I have a Form approval step and is sent to set of agents (through org unit id assignment on step). I have a requirement to programatically (by calling FMs may be) either approve or reject this form and complete the form from agents inbox. I