Call remains in "conferenced" state after the call is released

We have a scenario where a lengthy recorded message is set up through a ICM call routing script.  If we call the number we assigned to the script using our hard phones the call is disconnected as soon as the recorded message is finished playing.
When we use Cisco Administrator Desktop and the conference feature, the call remains in the "conferenced" state after the call has been released.
My assumption was that our reports would be smarter than CAD and would get it right.  However, reporting agrees with CAD, it thinks the call remained on a conference call for the whole time.
In the script we set some variables for the call, play the message through "RunExtScript" node, set a call type, than use the "ReleaseCall" node to disconnect the call. Any ideas how we can configure the script other than this?

Hi,
can you tell us more - do you have Translation Routing set up, perhaps?
Also, can you take a look at the Router Log (on the Distributor server).
And please swith the script to Monitoring mode to see where it fails.
G.

Similar Messages

  • Why does a VRRP master with preemption disabled regain master state after the reboot ?

    Q: Why does a VRRP master with preemption disabled regain master state after the reboot?
    A: This issue is found in the following scenarios:
    1. When spanning tree is disabled on either of the VRRP controllers but enabled on upstream switch(es).
    2. When the controller(any one VRRP controller) and upstream device(s) run different versions of STP.
    3. STP convergence time is different across the VRRP controllers.
    In these scenarios, rebooted vrrp master is expected to come back as vrrp MASTER as the link takes some time to converge and fail to receive VRRP advertisement packets from its peer and may roll back to MASTER.
    Trigger for this is, since STP is enabled on intermediate switch and disabled on controller, switch is taking some time ~30 secs to converge the link while port on the controller has become UP and fail-over to Master due to 
    not receiving VRRP advertisement packets
    In all these cases, it is advised to enable holdtime to mitigate issue. Holdtime has been introduced to tackle this issue in the "preemption disabled scenario".
    Configuration via CLI:
    (controller) (config) #vrrp <id>
    (controller) (config-vrrp)#holdtime
    Description:
    The VRRP virtual router does not begin listening to advertisements until the holdtime expires. If your deployment includes a VRRP master with preemption disabled and an uplink switch is running RSTP, a higher value will prevent the VRRP master from regaining the master state after it reboots.
    Range: 30 - 120 seconds
    Default: 45 seconds

    Hey Jim,
    Thanks for the follow-up.  Here are some more details:
    OS - 10.8.2
    FCP X - 10.0.7
    I can't update either of these because of my Avid installation.
    Something else I didn't mention – this happens in a 4K project.  Notice how a default Zoom title looks:
    Lines 1 and 2 are almost stacked on top of each other.
    Here's my title style:
    Here's what the title looks after I apply the title style, modify Line 1, and remove the contents of Line 2:
    And here's how it looks in the exported master file MOV:
    Notice how it's pushed down?
    Then I decided to make a 720p project.  No more title problems.
    So if you have some 4K footage, Jim, give it a go.  Or if there's another 4K-er out there, try this and let me know.
    Thanks!

  • How can I get Navigation Menu Button to remain in down state after clicked?

    Hi there,
    I'm messing about with a Navigation Menu and would like to click on the button and once clicked, the button remains in its down state.  I can't seem to find a way of doing this?  Any pointers?
    Cheers

    We would need to see your live page and code to offer more meaningful answers.  But I wonder if what you really want is a "persistent page indicator" on your nav menu?
    HOME  |  PRODUCTS  |  CONTACT US
    When you're on the Home page, the HOME menu is highlighted.
    HOME  |  PRODUCTS  |  CONTACT US
    When you're on the Products page, the PRODUCTS menu is highlighted. And so on...
    See this related discussion -
    http://forums.adobe.com/message/2398026#2398026
    Nancy O.
    Alt-Web Design & Publishing
    Web | Graphics | Print | Media  Specialists
    www.alt-web.com/
    www.twitter.com/altweb
    www.alt-web.blogspot.com

  • Jobs are going to released state after the PC triggers with user event.

    HI BI experts,
    We are facing issue with event scheduler using user event in the process chains. Some Jobs are not starting immediately with the event and reaching release state. These released jobs are never starts in near future. Also cannot start manually due to event periodic jobs.
    No log is availble in SM61 due to settings.
    Please let me know your suggestions and this issue.
    Regards,
    Mohan.

    HI BI experts,
    We are facing issue with event scheduler using user event in the process chains. Some Jobs are not starting immediately with the event and reaching release state. These released jobs are never starts in near future. Also cannot start manually due to event periodic jobs.
    No log is availble in SM61 due to settings.
    Please let me know your suggestions and this issue.
    Regards,
    Mohan.

  • Where to find OS X Lion after the Mountain Lion release?

    I have an old MacBook Pro at work, and it's compatible with Mountain Lion. Currently it's running Snow Leopard, but I'd like to upgrade to Lion. Where can I find the download? Since Mountain Lion was released, Lion disapeared from the App store...

    If you need to purchase Lion call 1-800-692-7753 or 1-800-676-2775. Ask for a Sales Representative. They will check your Apple ID, and email you a code and instructions.  The cost is $29.99 (as it was before) plus tax.  It's a download.
    Lion System Requirements
    Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or Xeon processor
    2GB of memory
    OS X v10.6.6 or later (v10.6.8 recommended)
    7GB of available space
    Some features require an Apple ID; terms apply.

  • Changing Budget amount values after the budget is released in Compensation.

    Hello All-
    Is there a way to change the budget amount in a budhget unit in Compensation management once its released? The budget value once released goes into Infotype 1520 Final Budget. Is there a way to change that value? I tried using PP01 and PP02 but I can not see the value to change it.
    Thanks-
    Chakri.

    HI,
    You can not change the budget value once it's ben released.. you can create a new budget and tag it to the compensation adjustment.

  • Approver gets refreshed after the contract is released

    Hi All,
    I am facing a problem while creating GOA i have activated the one step approval workflow WS 14000088 and have the agent assignment based on standard roles. I can see the approver picked up correctly in approval preview but when i release the contract or keep it in held status the approval preview gets refreshed and displays document approved and the approval workflow doesn't start. Also i tried with the N step approval for contract and the workflow behaviour is same in this case. Also in workflow diagnosis i could see error in task  WS14500051 and TS14507950 error message 'Recipient not found'.
    Please do let me know possible solution so as to get rid of this problem.
    Thanks in Advance.
    Anirban

    Hi,
    The problem  may be due to the roles which you have assigned to the Contract Creator and Contract Approver.
    Check whether you have assigned the role purchase manager to both the users i.e.
    1.  Contract Creator
    2.  Contract Approver
    Try to Assign the role Strategic Purchaser to Contract Creator and Assign the Role Purchase Manager to Contract Approver .
    System may be  identifying a role which was assigned to two or more persons and as the Creator is already having this role so it is neglecting the Approver.
    BR,
    Disha.
    Do reward points  for  useful answers.

  • Is there any way to close download windows that remain all black and open after the downloading ?

    <blockquote>Locking duplicate thread.<br>
    Please continue here: [[/questions/968842]]
    </blockquote>
    Hi,
    I have my download windows that remain black and open after the downloading achieved. The only button active is the red cross but seems to be inoperative...
    I can have couple of them open at the end of the day at the same time.
    I have already tried to uninstall/resinstall but the problem remains...
    For info, i am running firefox on a Mac OS.
    Thanks in advance for your help.
    Cheers,
    Jul_313

    Hello,
    Try disabling graphics hardware acceleration. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.
    You might need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
    Then perform these steps:
    *Click the orange Firefox button at the top left, then select the "Options" button, or, if there is no Firefox button at the top, go to Tools > Options.
    *In the Firefox options window click the ''Advanced'' tab, then select "General".
    *In the settings list, you should find the ''Use hardware acceleration when available'' checkbox. Uncheck this checkbox.
    *Now, restart Firefox and see if the problems persist.
    Additionally, please check for updates for your graphics driver by following the steps mentioned in the following Knowledge base articles:
    * [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]]
    * [[Upgrade your graphics drivers to use hardware acceleration and WebGL]]
    Did this fix your problems? Please report back to us!
    Thank you.

  • Gather stats after shrink command

    Hello.
    Running Oracle 11.2 and was preparing to run shrink command on a major table to release 5G of wasted space on a 15G segment.
    I have already done this in our test database and was preparing to do this in production, when one web site I went to said we should run fresh stats after the shrink operation.
    Does this make sense, and does it seem to be necessary?
    It does seem to make sense that the values for number of blocks, number of empty blocks would be different after the shrink operation.
    But I am surprised I did not see this recommendation on any other site except the one site.

    Well, sure... if we want to consider this a DML or DDL operation, but actually, we are not changing or defining new data structure, and we are not manipulating the data (per se).
    But, I'm in agreement that it makes sense to gather fresh stats just based on the difference of blocks and empty blocks which we can assume the optimizer considers when choosing an execution plan.

  • MaxDB in strange state after power supply blackout

    Hello DB specialists,
    I'd like to ask if anyone has faced similar problem as we do. We had a power supply blackout in the server room and one of our UPS didn't survive. Two servers went down immediatelly - lusckly both ofthem for training purposes. When we restarted them and started all SAP systems everythink seemd ok. But after couple of days we realized, that SolMan system contained old license, which was renewed nearly a year ago. When we logged to the system, we realized that the DB is in state of more than year ago. It appears like after the DB restore.
    We localized some strange files in /sapdb/data/wrk/<SID>/DIAGHISTORY from the time of restart after the power crash.
    My question is - might it be, that the DB rebuilt itself to some previouse state after the system crush ? And if so - is there any way to restore the last state ?
    Thank you for your comments in advance.
    Best regards
    Tomas

    >
    Tomas Toth wrote:
    > But I think .. even OVERWRITE LOG mode would cause the same problem .. or does it not ?
    >
    > I remind that we are talking about non-production system, the system is used for demo purposes and there are not many changes there.
    >
    > Thx.
    > Tomas
    No, it won't.
    The key point here is, that log mode OVERWRITE still lets the logwriter do its job and with that the automatic savepoints do occur.
    It's just that the written log data is not kept from beeing overwritten without having a backup for it.
    When you crash such an instance it will startup from the last written savepoint which is likely <=10 minutes away. And depending on your log data state, all other changes made after this are still in the log volume.
    So it's quite a good choice for situations where you don't really need everything to be recoverable up to the latest minute. For example demo systems or training systems could be a use case.
    LOGWRITER OFF on the other hand completely disables the log writing and by that also the automatic savepoints.
    regards,
    Lars

  • Firefox has prevented an outdated plugin 'adobe flash' from running. This didn't start until the latest Firefox release, and I don't use M$Winblows. Linux only

    I just started started seeing this after the latest firefox release. I see it on M$Winblows at work, Linux and Mac at home, so it isn't activex related for me. I can't upgrade Flash for Linux since Adobe stopped supporting it, but I haven't had any issues up until the last week. And as far as Mac and Windows, they are up to date in patches. Once again engineers just love to make things better. If there was a better alternitive to Firefox I'd use it.

    The outdated Flash plugins is not due to any Firefox version or updates but due to a blocklist of vulnerable Flash plugins made on Dec 11/12. The Firefox 31.3.0esr and 34 were released on December 1st and the updated Flash came out on Dec 9.
    For Windows and Mac 16.0.0.235, 13.0.0.25'''9''' ESR and 15.0.0.24'''6''' are not vulnerable according to Adobe and are not on blocklist.
    For Linux the Flash 11.2.202.42'''5''' is not vulnerable according to Adobe and is not on blocklist while 11.2.202.42'''4''' and older is. Adobe is still supporting the Flash 11.2 with security fixes.
    Get choice of 16.0.0.235 or 13.0.0.25'''9''' ESR for Windows/Mac and the 11.2.202.42'''5''' for Linux at https://www.adobe.com/products/flashplayer/distribution3.html
    https://addons.mozilla.org/firefox/blocked/
    https://helpx.adobe.com/security/products/flash-player/apsb14-27.html

  • CAD stays in talking state after hanging up a call

    Hi I have the following issue
    Problem description:
    After the Cisco Agent Desktop completes a call and disconnects, the Agent stays in the Talking state instead of the Ready state. The agent must manually log out and log in to go into the Ready state.
    This incident most likely occurs on this occasion:
    The Cisco Agent Desktop takes a call and the remote caller hangs up first. Then the Agent hangs up.
    We use:
    CUCM version 6.1.4.1000-10
    CCX 7.0
    CAD 6.6(1) Premium version
    Workstation runs Windows Vista Pro
    Part of the text in the problem description was copied from this link:
    http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_tech_note09186a00801cce5d.shtml
    The problem description is an almost perfect match for what we experience, however the solution does not apply. Neither does the CUCM version.
    Anyone have an idea?
    thanks

    Hi
    I've seen this before. It turned out to be a bug with the CUCM version:
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCtb77537
    Regards
    Aaron
    Please rate helpful posts...

  • Screen doesnt get blacked out when on call after the new update

    Since the time i Have updated the firmware screen doesnt gets blacked out, when on call after the new update. Because of this option automatically get selected by getting touched cheecks.
    any solution?

    Please try to update your plugins [http://www.mozilla.org/en-US/plugincheck/] Flash is out of date.
    Also the Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
    '''Note''': ''This will cause you to lose any Extensions and some Preferences.''
    *Open websites will not be saved in Firefox versions lower than 25.
    To Reset Firefox do the following:
    '''For Firefox versions previous to 29.0:'''
    #Go to Firefox > Help > Troubleshooting Information.
    #Click the "Reset Firefox"[[Image:Button reset]] button.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    '''For Firefox 29.0 and above:'''
    #Click the menu button [[Image:New Fx Menu]], click help [[Image:Help-29]] and select ''Troubleshooting Information''.
    Now, a new tab containing your troubleshooting information should open.
    #At the top right corner of the page, you should see a button that says "Reset Firefox"[[Image:Button reset]]. Click on it.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
    Did this fix your problems? Please report back to us!
    Thank you.

  • Q10 search remains on a contact after search and call - any way to auto close?

    Hi,
    I'm just starting to try out a q10 for work purposes and one issue I ran into several times today...
    After typing in a contact name (to search) and then selecting call or email, making call or writing email and the turning screen off:
    The next time I turn the phone on to search for anything, the contact I had searched before appears. Usually after a few button presses I realize it and by then I'm stuck in editing that contact.
    Is there a way to have the search close after the call/email ?
    Or maybe have it reset after a while ?
    Or, even better would be a gesture I can use from when the screen is off to activate screen and start a new ?
    On that last point, depending on the state that I left the phone in it seems I must to do different things to perform a new contact search...
    For example search is showing a contact already and I'm not on the search screen:
      Swipe up or power button to activate Press a key to start a search Swipe left to leave the contact that was displayed by search
      If search is not showing a contact then I just swipe up and type a name
    Also, different topic but I am really hoping there is a simple solution here:  is there a rapid way to jump straight into the hub?  
    Sometimes I need to swipe up to turn on, swipe up to exit an app the swipe right swipe right and swipe right to get into the hub.  It feels kind of disorienting since it's not always the same procedure and I'd like these things to be "muscle memory."  
    Thanks, 
    Dave

    after youve called the contact and it opens with their name again just tap cancel on top right of screen and it puts you back to the first person in your contacts list.
    its the only way ive found out how to close the cotacts name.

  • How to call  a javascript method after the PPR event has finished  ?

    Hi!
    How can we make a javascript method get called after the processing of ADF PPR event?
    My specific use case is,
    I want to call a javascript function after the data in the table is loaded...
    In 10g, that is not a problem, as the data used to get loaded directly during onLoad, and so i would call my js function on load;
    but in 11g , the table data is being loaded through PPR which is initiated onload, and so i needed to call my function after the PPR Response processing has been done; for which I need the name of the event triggered at that instance.
    Is it possible to do this?
    Regards,
    Samba

    Hey, I got it.
    I handled the ADF Controller's PREPARE_RENDER_ID phase of the lifecycle, and then called the
    script to get Executed.
    The code :
        public void afterPhase(PagePhaseEvent pagePhaseEvent) {
            FacesPageLifecycleContext ctx = (FacesPageLifecycleContext)pagePhaseEvent.getLifecycleContext();
                 if (pagePhaseEvent.getPhaseId() == Lifecycle.PREPARE_RENDER_ID) {
                    if(AdfFacesContext.getCurrentInstance().isPostback() )
                        afterRender();
        }is written in lifecycle listener , and my backing bean extended this listener ,
    and in the afterRender() method I did this :
       public void  afterRender(){
                System.out.println("AFTER RENDER CALLED");
               FacesContext context = FacesContext.getCurrentInstance();
               ExtendedRenderKitService service = (ExtendedRenderKitService)Service.getRenderKitService(context, ExtendedRenderKitService.class);
               service.addScript(context, "translate();");
           }That's it.
    It did work, magnificently.
    Thanks for the idea.
    Regards,
    Samba

Maybe you are looking for

  • Problem in running the query on ODS

    Hi All, I have been trying to run the query which consists of only 25 fields and doen't contain much calculations and routines and trying to restrict even 7000 records. That too result in system failure reporting on storage parameters somtimes giving

  • BAPI_PO_CREATE1 - In case of account assignment, please enter acc. assignment data for item

    Hi, Currently I'm facing an error "In case of account assignment, please enter acc. assignment data for item" when create a Purchase Order using BAPI_PO_CREATE1. The condition of the data that need to pump into the system is that this PO is an open i

  • I'm trying to edit in Adobe Acrobat Pro 9

    I can't seem to find an alignment tool and my text is not centering.  Help please!! Thank you

  • Variable values being reset to # / 00.0000

    Hi I have a problem with our web template, although the same thing happens on the SAP default template. Run a template, and you are shown the variable selection screen. For this particular query, there are 2 variables, namely SITE and FISCAL PERIOD/Y

  • ITAB_ILLEGAL_SORT_ORDER dump in CIC searching for Opportunities

    Hi All, We currently have a strange problem when trying to search for opportunities in the CIC.  We go in, enter a partner number and select it as the main partner.  Then, we chose Opportunity as the object to find, enter a date range and click on st