Call Roll Over

Before I switched to Digital Voice, I had two lines where the 1st line would roll over to the second line if it was busy.  How do I do this in Digital Voice?

The closest would be the "Locate Me" feature. You can program this by logging into your account at www.verizon.com/fiosvoice . Also on this login page there is a link for the user manual in the lower right hand side. Once logged in, click on "Calling Features". From there you can click on the "Locate Me" feature to turn it on and assign the list of numbers to call.
Anthony_VZ
**If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

Similar Messages

  • Question about calls rolling over

    Sorry for the noob question but here goes.  I have Call Manager v7.  My question is if I have 3 phones with one ext 0009 and I want the calls to go to the first phone and if that person isn't there go to the next phone and then if that person isn't there go to the last phone. If the last person isn't there, have it go to vm.  Hopefully that made sense.  These are all 7941 phones.

    Hi yulook,
    You would need to take the Shared Support Line/DN 0009 and make
    it a new Hunt Pilot DN. Then on the Level 1,2 & 3 phones you would put
    a new DN on Line button 1. Shared lines like 0009 will always ring all
    phones simultaneously in your current config.
    In the Line Group that is associated with the new Shared Support Hunt
    Pilot you can then set a Top Down algorithm that routes to Level 1, Level 2
    and Level 3 DN Line Group members in the chosen order
    Line Groups
    Line groups contain one or more directory numbers. A distribution algorithm, such as Top Down, Circular, Longest Idle Time, or Broadcast, associates with a line group. Line groups also have an associated Ring No Answer reversion timeout value.
    The following descriptions apply to the members of a line group:
    An idle member designates one that is not serving any call.
    An available member designates one that is serving an active call but can accept a new call(s).
    A busy member cannot accept any calls.
    For information on configuring line groups,
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/4_2_3/ccmcfg/b03lngrp.html
    Hunt Lists
    Hunt lists comprise ordered groupings of line groups. A line group may belong to more than one hunt list. Hunt pilots associate with hunt lists. A hunt list may associate with more than one hunt pilot.
    For information on configuring hunt lists,
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/4_2_3/ccmcfg/b03htlst.html
    Hunt Pilots ..this is what 0009 would become.
    Hunt pilots are sets of digits. They comprise lists of route patterns that are used for hunting. A hunt pilot can specify a partition, numbering plan, route filter, and hunt forward settings. A hunt pilot must specify a hunt list.
    For information on configuring hunt pilots,
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/4_2_3/ccmcfg/b03htpil.html
    Cheers!
    Rob

  • Call Manager Express Hunt Group roll over doesn't work correctly

    Hello,I have a wierd issue occuring on the CME portion of a client's UC520. Currently, I have a hunt group set up that has 1 user and then the auto attendant. Basically, I want to give a user a chance to answer the main line, and if she doesn't, it then roll's to the main auto attendant. This is working as long as I keep the time out on the hunt group under 12 seconds. The issue is that is about 2.5 rings. She'd like a little more time to be able to pick it up. When I put the time out above 12 seconds (say 16) and dial from an external number, it rings her phone correctly, then you can hear it attempt to transfer, but it transfers it back to her phone instead of rolling over to the auto attendant. You can even see on her phone that the transfer occurs and it transfers to herself. For an instance, it shows 2 calls with the same caller ID. Change the time out back under to 12 or under, and everything works great. Any help would be greatly appreciated.

    Sorry about that. Here is the IOS.
    Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
    And here is some relevant code.
    ephone-hunt 1 sequential
    pilot 501
    list 201
    final 401
    timeout 11
    no-reg pilot
    statistics collect
    destination-pattern 401
    b2bua
    voice-class sip outbound-proxy ipv4:10.1.10.1
    session protocol sipv2
    session target ipv4:10.1.10.1
    dtmf-relay sip-notify
    codec g711ulaw
    no vad

  • Swap images while rolling over popup menu

    Hello,
    I've been playing with fireworks CS5 for some days now and made a first attempt on a website.
    So far, i've made a navigation bar with two states in order to be able to add a simple roll over behavior, e.g. darkening text on rollover. I also have been able to make a dropdown menu (popup) via slices.
    Then I decided to swap images when on nav bar headings. So far, so good.
    When I did a preview in my browser, it appeared that as soon as I was leaving the nav bar, the image swapped back to the old setting. Perfect.
    But when I did a mouse over on one of the dropdown menu's of the navigation bar, the image swapped back as well.. I've been trying, but didnt manage to find out how to fix this.
    So, is there anyone here that knows if it is possible, and if so, how to keep images swapped to a second stage as long as the mouse is on the dropdown menu, but swaps back to the original state when leaving the dropdown and/or the navigation bar.
    Thanks in advance,

    Hi Bryan,
    It may be possible to cheat and put this onto the button:
    the option that you want is called TITLE.
    if you set one of the other parameters (e.g. the label)
    to be:
    LABEL_TEXT" TITLE="TITLE_TEXT
    basically when it adds the text onto the form it will wrap it in "
    If it doesn't strip out the " from your text you should get your extra parameter.
    it may slip past the portal checking.
    I can't test it as I only have WebDB, but I have done something similar with javascript in WebDB.
    good luck
    Michael

  • Indesign roll over question

    I have 2 images on a layout called "A" and "B".  I Also have on the layout an image called "Button" with is a button.  My 4th image called image “C” is the pop up image that pops up when the button image is moused over. I have placed image “C” on the very top. But when I roll over the button image, the “C” image only pops up over image “A” but not “B”. I have made sure images “A” and “B” are in the back and image “C” is in the front. How can I get image “C” to pop up over both image “A” and “B”.  Thanks.

    Thanks so much, Ken for your answer.
    I made this site years ago in Adobe GoLive, and wanted to update it in
    Dreamweaver.
    http://www.brendamolloy.com
    Thanks again for your help!

  • Roll over a small photo and above it (or beside) the large photo is displayed

    Hi All
    What is this called: When you roll over a small photo and
    above it (or beside) the large version of the photo is displayed. I
    would like to create a photo gallery that works this way. Could
    someone tell me what this is called? Or better yet, where I can
    learn how to do this? A free tutorial perhaps?

    c2design,
    > What is this called: When you roll over a small photo
    > and above it (or beside) the large version of the photo
    > is displayed.
    I don't know that the phenomenon has one ultimately correct
    name. I
    might call that a "click to enlarge" or "rollover to enlarge"
    effect.
    > I would like to create a photo gallery that works this
    > way. Could someone tell me what this is called? Or
    > better yet, where I can learn how to do this? A free
    > tutorial perhaps?
    Flash generally provides many ways to accomplish a desired
    task. One of
    the easiest ways I can think of to get what you're after is
    to create a
    button symbol. Put your small image (the "thumbnail," it's
    usually called)
    into the button's Up frame. Put the large image in the
    button's Over (and
    perhaps Down) frame. In the Hit frame, put a shape that
    represents where
    you want someone to roll over in order for the Over frame to
    show.
    Typically, you'd just put the thumbnail into the Hit frame at
    the same
    horizontal and vertical position it was in the Up frame.
    You could also program this effect with ActionScript, but
    since you
    posted in the general forum, let's see what you make of the
    button approach.
    Write back if you still have questions. :)
    David Stiller
    Adobe Community Expert
    Dev blog,
    http://www.quip.net/blog/
    "Luck is the residue of good design."

  • Roll over button sound

    Hello,
    i'm trying to get a sound clip to play when rolling over the
    buttons. I was trying to integrate the following function to my
    actionscript file, but it ain't working. i have tried many
    variations but no luck, any ideas?
    thanks
    Function:
    this.addEventListener(MouseEvent.MOUSE_OVER, playSound);
    function playSound(event:MouseEvent):void {
    mySoundChannel = mySound.play();
    var mySoundReq:URLRequest = new URLRequest("songsample.mp3");
    var mySound:Sound = new Sound();
    var mySoundChannel:SoundChannel = new SoundChannel();
    mySound.load(mySoundReq);
    Actionscript file code:
    package {
    import flash.display.*;
    import flash.events.*;
    import flash.net.*;
    public class sieges extends flash.display.MovieClip{
    var debug:Boolean=true;
    public const SIEGE_LIBRE:int = 0;
    public const SIEGE_SYSTEME:int = 1;
    public const SIEGE_USER:int = 2;
    var status:int = SIEGE_LIBRE;
    // constructeur
    public function sieges () {
    if (debug) trace("siege:"+this.name);
    this.addEventListener(MouseEvent.CLICK, siege_click);
    this.addEventListener(MouseEvent.MOUSE_OVER, siege_over);
    this.addEventListener(MouseEvent.MOUSE_OUT, siege_out);
    siege_init();
    // click sur un siege
    function siege_click(event:MouseEvent):void {
    if (debug) trace("siege_click");
    if (this.status == SIEGE_LIBRE) {
    user_reservation();
    } else if (this.status == SIEGE_USER) {
    siege_init();
    this.parent.parent["durocher"].enleve_siege(this.name);
    // over un siege
    function siege_over(event:MouseEvent):void {
    if (debug) trace("siege_over");
    var request:URLRequest = new
    URLRequest("/reservations/images/"+this.name+".jpg");
    this.parent["photo"].scaleContent = true;
    this.parent["photo"].addEventListener(IOErrorEvent.IO_ERROR,
    ioErrorHandler);
    this.parent["photo"].load(request);
    event.target.alpha = .5;
    function siege_out(event:MouseEvent):void {
    if (debug) trace("siege_over");
    event.target.alpha = 1;
    function ioErrorHandler(e:Event):void {
    public function siege_init() {
    if (debug) trace("siege_init");
    this.status = SIEGE_LIBRE;
    gotoAndStop(1);
    // reservation pour un usager
    public function user_reservation () {
    if (debug) trace("user_reservation");
    this.status = SIEGE_USER;
    this.parent.parent["durocher"].reserve_siege(this.name);
    gotoAndPlay(10);
    // reservation pour le systeme
    public function system_reservation () {
    if (debug) trace("syste,_reservation");
    this.status = SIEGE_SYSTEME;
    gotoAndPlay(5);
    Actionscript file code

    does playSound() called?

  • Swap another image when rolling over another one

    i would like to roll over a small thumbnail and swap out a
    larger image on the page. i've been trying all morning and i just
    can;t seem to get it. what are the steps? i want to roll over
    "thumb.jpg" and swap "text_large.jpg" with "product_large.jpg".
    any help would be wonderful.

    In DW we call this a disjointed (or disjoint) rollover -
    here's a tut for
    you........
    http://www.dwfaq.com/tutorials/basics/disjointed.asp
    Murray --- ICQ 71997575
    Adobe Community Expert
    (If you *MUST* email me, don't LAUGH when you do so!)
    ==================
    http://www.projectseven.com/go
    - DW FAQs, Tutorials & Resources
    http://www.dwfaq.com - DW FAQs,
    Tutorials & Resources
    ==================
    "divebombinc" <[email protected]> wrote in
    message
    news:ga620o$804$[email protected]..
    >i would like to roll over a small thumbnail and swap out
    a larger image on
    >the
    > page. i've been trying all morning and i just can;t seem
    to get it. what
    > are
    > the steps? i want to roll over "thumb.jpg" and swap
    "text_large.jpg" with
    > "product_large.jpg".
    > any help would be wonderful.
    >

  • Q - roll over - img appear somewhere else

    how do i make roll over, like when i roll over a spot, image
    will appear or change somewhere else? or is that flash?

    This is a good one.
    http://www.dwfaq.com/tutorials/basics/disjointed.asp
    Murray --- ICQ 71997575
    Adobe Community Expert
    (If you *MUST* email me, don't LAUGH when you do so!)
    ==================
    http://www.projectseven.com/go
    - DW FAQs, Tutorials & Resources
    http://www.dwfaq.com - DW FAQs,
    Tutorials & Resources
    ==================
    "Nancy O" <[email protected]> wrote in message
    news:gq6hsj$rf5$[email protected]..
    > It's called a disjointed rollover. Google search this
    term and you will
    > find many examples.
    >
    >
    > --
    > Nancy O.
    > Alt-Web Design & Publishing
    > www.alt-web.com
    > www.twitter.com/altweb
    > www.alt-web.blogspot.com/
    >
    >

  • Counter roll-over when measuring period

    Hi,
    I'm using PCI-6251 counter 0 to continuously measure the period of a signal, and I notice there are occasionally  error readings. Since the counter can roll over when it reaches 2^32-1, I need to know what will happen to the period measurement when counter roll overs. Would anyone please help me?
    Thanks.
    David

    The count value will simply wrap-around back to 0 and then continue to increment.  I can think of a few ways to handle this:
    1. Specify a slower timebase for the measurement.  If you go from, say, 80 MHz to 100 kHz, it'll take 800 times as long a period to cause rollover.  This method is pretty simple to implement, but not all apps can accept the loss in precision.
    2.  You can use a 2nd counter to be sensitive to the 1st counter's "terminal count".  This gets a bit complex, so you may need to do more research on some of the terms that follow.
    An internal pulse signal is generated on the board when the 1st counter rolls over from 2^32-1 back to 0.  It's commonly known as "terminal count" or TC.  You'll need to configure a 2nd counter that also measures periods of your external signal, but which uses those TC pulses as its timebase signal.  You may need to fiddle with the "Duplicate Count Prevention" property on the 2nd counter so that it will buffer values of 0 during the majority of intervals where no TC pulse occurs.  During the intervals where rollover happens, the 2nd counter will count how many times it happens.
    You would further need the 2 counters to be started off a common "arm start" trigger to keep their data sync'ed.
    3.  Software method.  You can query the DAQmx Channel property "Counter Input -> General Properties -> More -> Terminal Count Reached".  When you get a 'True' output, the property resets such that subsequent calls will return 'False' until the next rollover occurs.  The problem here is trying to correlate this software-detected rollover with a specific period in the 1st counter's measurement buffer.  You'd probably also need to be querying and tracking the DAQmx Read property for Total Samples Acquired both before and after the TC event.  Even then you might not always be able to determine unambiguously which interval had the TC event.
    -Kevin P.

  • Roll over balloons in eBay searches not poping up w/ Safari 2.0.4

    Is there a setting or a technique to once again allow roll over balloons to pop up on eBay search listings? I'm referring to the "Enlarge" roll over link in the Gallery picture of search results. This is a "paid for" option that some sellers use.
    I do not have "Block Pop-up Windows" checked off in the Security Preference window.
    Firefox still allows this, but on both a Powerbook G4 and a iMac Dual Core using Safari Version 2.0.4 (419.3) this feature is no longer working for me. (It had worked in Safari until three days ago...could I have inadvertaently changed something?)
    For an example of a roll over balloon try searching eBay for an item of interest, and then scan down the resulting list. Typically a few items in large search results will have the "Enlarge" roll over below the gallery picture of an item being sold.
    24" iMac 2.16 Dual Core   Mac OS X (10.4.8)   Also, Powerbook 17" G4 & Powerbook G3

    Thanks again.
    BTW... I just received this from eBay in regard to my questioning them about this problem. As you said, they seem to be disregarding Safari.
    Dear eBay Member,
    Thank you for writing eBay in regard to the problem you are experiencing
    while trying to list your item using the Safari browser.
    If you are using OS X 10.2.x or higher, I would like to suggest using
    the Firefox browser. This browser seems to be the most compatible format
    for Macintosh users for eBay Picture Services.
    If you don't already have this browser installed on your computer,
    please visit the following page to download the Firefox browser:
    http://www.mozilla.org/products/firefox/all
    Once the page loads, please select which language you would like to
    download, and click on the link under the Mac OS X column.
    If you are using OS X 10.2.8 or older, I would then recommend using the
    Netscape browser. If you don't have this browser installed on your
    computer, please visit the following page:
    http://browser.netscape.com/ns8/download/archive72x.jsp
    Thank you for being a valuable member of the eBay community. Have an
    enjoyable time shopping and selling on eBay!
    Sincerely,
    Adam
    eBay Customer Support
    Powerbook 17" G4 & 24" iMac 2.16 Dual Core   Mac OS X (10.4.8)   Also, Powerbook G3 250 / OS 9

  • How can i change the color of the text on a button in Roll Over or Click state (Cs5.5)

    Hello,
    Here is the problematic:
    1° How can i change the color of the text on a button in Roll Over or Click state (Cs5.5)
    - I've many button in a doc im creating
    - the color of the buttons is white with black stoke & black text
    - in roll over state i want them to inverse the color coding (the text white & bottom black)
    - currently the text becomes invisible as black on black cant be seen (ive stroked it white but that looks ugly)
    - i would just like to know if there is a function made for this?
    My other questions:
    2° Ive a presentation on which Ive created buttons which tigger pop-up animations
    - i have 5 buttons which trigger animations
    - the viewer can chose to Click on any of the buttons randomly
    - the problem is once the animation is open how can it be close... either:
    a) by it self after "40" seconds
    b) when ther viewer clicks another button
    3° Ive created buttons linking pages..
    - "go to page xxx"
    - when i do a preview and click on the buttons the links dont take me to the right pages
    - is that normal? (maybe in preview its suppose to be like that)
    4° I would like to intergrate YouTube videos in the presentation so they play inside the docment.. when i tried.. it said the 'link isnt a flash video'
    - what should i do?
    5° Once i export it into Swf. how how can i visualize it? or put it online?
    Thank you for your time.

    stlbbl4u wrote:
    Hello,
    Here is the problematic:
    1° How can i change the color of the text on a button in Roll Over or Click state (Cs5.5)
    - I've many button in a doc im creating
    - the color of the buttons is white with black stoke & black text
    - in roll over state i want them to inverse the color coding (the text white & bottom black)
    - currently the text becomes invisible as black on black cant be seen (ive stroked it white but that looks ugly)
    - i would just like to know if there is a function made for this?
    You should setup Object Styles - these can also include Paragarph Styles that can be triggered when the Style is selected.
    http://help.adobe.com/en_US/indesign/cs/using/WS5CEDB81A-0011-4dc9-9DE8-AC7AD4C80076a.html
    My other questions:
    2° Ive a presentation on which Ive created buttons which tigger pop-up animations
    - i have 5 buttons which trigger animations
    - the viewer can chose to Click on any of the buttons randomly
    - the problem is once the animation is open how can it be close... either:
    a) by it self after "40" seconds
    b) when ther viewer clicks another button
    I'm not sure what you mean - I don't do files with Animations
    3° Ive created buttons linking pages..- "go to page xxx"
    - when i do a preview and click on the buttons the links dont take me to the right pages
    - is that normal? (maybe in preview its suppose to be like that)
    Does it work properly when you export it to the finished file?
    4° I would like to intergrate YouTube videos in the presentation so they play inside the docment.. when i tried.. it said the 'link isnt a flash video'- what should i do?
    InDesign won't link directly to youtube videos. I think your best bet would be to use Downloader to download the video and embed them directly in Indesign.
    5° Once i export it into Swf. how how can i visualize it? or put it online? 
    Thank you for your time.
    You can look up how to embed a SWF file into your HTML - but it depends what you mean by "online" there's a dozen ways to get a file "online".

  • How do I make a textbox appear in a PDF made in InDesign CC when the cursor rolls over another textbox?

    I'm trying to make a textbox appear in a PDF made in InDesign when the user rolls the cursor over another textbox, and I want it to disappear when the cursor moves off the first textbox. I've tried the following with various setting, and it's just not working for me.
    Display a different button on rollover
    You can create a hot spot in which clicking or mousing over an object displays another object. To do this, create two buttons, hide one of the buttons, and use the Show/Hide Button action to show and hide the target button.
    Create an object to be used as the source button. In the Buttons panel, click the Convert Object To A Button icon.  
    Place the image you want to be used as the target button, and convert it to a button.  
    Select the target image and select Hidden Until Triggered at the bottom of the Buttons panel.  
    The image needs to be hidden in the exported document so that it can be displayed when the source button is moused over or clicked.  
    Select the source button and create two different actions, one to show the target image and a second to hide the target image.  
    If you want the image to appear when the mouse hovers over the source button, use the On Roll Over and On Roll Off events. If you want the image to appear when you click the source button and disappear when you release it, use the On Click and On Release events. In either case, use the Show/Hide Buttons action to display and hide the target button. See Make buttons interactive.   
    Use the Preview panel to test the buttons.  

    Here's more information about what I'm doing.
    1. create text box with a little text
    2. turn it into a button (Button 1)
    3. create another text box with some text
    4. turn this into a button (Button 2)
    5. check "Hidden Until Triggered" for Button 2
    6. For Button 1, select "On Roll Over" for Event
    7. For Button 1, click + to add Action and choose "Show/Hide Buttons and Forms"
    8. For Button 1, change icon next to Button 2 into eyeball (which I assume makes Button 2 visible on roll over).
    9. For Button 1,, select "On Roll Off" for Event
    7. For Button 1, click + to add Action and choose "Show/Hide Buttons and Forms"
    8. For Button 1, change icon next to Button 2 into crossed-out eyeball (which I assume makes Button 2 invisible on roll off).
    8. Export to PDF with modified smallest file size and include bookmarks and hyperlinks and include appearance for interactive elements.
    Both buttons are visible in the PDF, and nothing happens with roll over and off.
    What am I doing wrong?

  • Roll over images in a slide show

    I am trying to make a slide show of before and after images for a client.
    Rather than just have them all one after the other, I want all the after images to display as normal, and the before to display on hover for each slide.
    I can make this work in a basic slide show when rather than adding an image to the Hero Image box, I use the fill and states.
    However this only allows me to do one, as I can't add any more empty Hero Image boxes (or I don't know how to do that, is it possible?)
    When I add an image via the slide show menu it appears on top of any fills, and I can't seem to give images added this way a roll over state.
    Can anyone tell me how to either add extra blank Hero Image boxes, or how to apply the effect I want to the images in the Hero Image boxes.
    Thanks in advance, if there is any further info I can provide about my problem, please let me know!
    M

    Hi,
    You cannot add multiple hero image boxes within the same Slideshow. Now , you can use different slideshows for your different images but that wont give you the slideshow effect but you will be able to see all your after images at once and then if you rollover them you would be able to see the before images.
    Now, In order to create the effect that you want, what I would suggest you is to use a 'Composition widget'. In the composition widget, you can make the triggers as small thumbnails for your images and in the Target you can set the fill as your after image and in rollover state you can use the before image. After this you can use the Autoplay feature available in the composition widget and you will get the desired result.
    Hope this helps
    Regards,
    Rohit Nair

  • Is there a way to prevent roll-over ads from opening? Some sites are almost impossible to navigate because of this new nuisance.

    For instance, www.roughstock.com is a country music website where you can see lyrics and chords for popular songs that contributors have sent in. From the main page you click on the "Cowpie" tab to enter the page where you can search for songs. If you do this I am quite sure you will experience one of the roll-over advertisements I am talking about. They are small ads which, if you touch any portion of their area, will TAKE OVER the screen and play until the advertisement is finished or until you are able to find a usually obscure 'close' button.
    I've got 'pop-ups' disabled, but this new kind of ad is already resident on the page you wish to view so it is beating the system.
    Also, I'm not spamming for that site, it's just the most recent site where I've experienced this problem.

    It's going to get worse with crap like that as more web sites adopt HTML5 and HTML5 compatible browsers are released. There's all sorts of new tags in HTML5 that will probably be misused for displays like that.

Maybe you are looking for