Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Similar Messages

Cisco Jabber for Windows in Extend and Connect mode and making outbound calls

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

Cisco Jabber for Windows Client SDK

Is there an SDK for Cisco Jabber for Windows client? I could only find the Web SDK. Are there no other SDKs that would let me control features of the Jabber Windows Client?

And in order to avoid TAPI limitation, they say they have started using Jabber which controls all phone functionalities through an Application User connected to the Call Manager.
Assuming they are referring to the normal Jabber for Windows/Mac/iOS/Android applications then this is wrong. Jabber - the client, not the IM&P servers which are part of the CUCM cluster (if you're familiar with Lync consider CUCM+IM&P servers a Front End Pool) - do not use an Application User at all. When a user starts Jabber, assuming SAML SSO is off, they supply an email address. This is used to find the servers via DNS SRV records, or the Mobile and Remote Access Expressway (roughly analogous to a Lync Edge pool) to tunnel through the firewall. After the email address they are prompted for their End User username and password. This is then used to access several APIs on the server, namely the User Data Service to discover what the user has. This would include what the user has configured/available to them. After this is done the Jabber client does one of three things with respect to phone functionality:
If the user has no phone devices provisioned for them - physical or software - it becomes an IM&P client only.
If the user has a software phone phone provisioned, it registers as that using SIP. In this way Jabber is the actual phone. This is called a CSF device for Jabber Windows/OS X.
If the user has a desk phone assigned to their End User account AND administrative policy is to default to desk phone control, it registers to CTI Manager on the CUCM server to control the user's physical phone.
A user can toggle between option two and three, if appropriately provisioned, but cannot have both simultaneously. In other words, Jabber is either controlling a physical phone over CTI or is a phone itself using SIP. The difference is where the audio/video media is sent from/to.
All of this happens using that human's End User credentials.
Now, if you wanted to have a server control the user's phone - either a physical one or Jabber - you would use the TSP as an interface to CTI Manager on the CUCM server and receive real-time events (e.g. the user went off-hook, the phone is ringing with this caller ID, etc.) and issue commands to that phone (e.g. make a call to X). This is done using an Application User account because the server would need to do this for multiple users simultaneously. If you also use the Super Provider concept, the CUCM administrator doesn't have to take the extra step of associating every phone to your Application User manually. Instead, you can simply issue CTI subscriptions to see any/all device activity you want.
This is all assuming you wanted to do the integration server-side to avoid having to update the Cisco TSP application on every user PC (which also limits your WPF application to machines capable of running the TSP) every time the CUCM administrator patches the servers. If you don't care about that, then you can do this all client-side on the user's PC, and have them supply their End User credentials.
Of course, you could also reconsider the Jabber SDK and just embed the make/receive call functionality directly into your application instead.

Cisco Jabber for Windows - Anti-Virus Software

Hello,
Cisco Jabber for Windows could not resolve outlook contacts, when a client has installed McAffee Anti-Virus Software.
Is there any documentation available, how to setup a Anti-Virus Software, to get Cisco Jabber for Windows running?
Cisco Jabber for Windows Version 9.2.4 Build 4528
Outlook 2013
Thanks
Alex

this is all what we mention about antivirus; http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/jabber/Windows/9_2/JABW_BK_J6915A59_00_jabber-windows-server-setup/JABW_BK_J6915A59_00_jabber-windows-server-setup_chapter_00.html
Some antivirus or firewall applications, such as Symantec EndPoint Protection, block inbound CDP packets, which disables desk phone video capabilities. You should configure your antivirus or firewall application to allow inbound CDP packets. See the following Symantec technical document for additional details about this issue: Cisco IP Phone version 7970 and Cisco Unified Video Advantage is Blocked by Network Threat Protection.
with that being said; we probably would like to get the jabber process excluded from the antivirus list so that it allows for inbound MAPI communication as that is what is used for quering for the outlook contact.
The only process that ever runs from Jabber for windows is "CiscoJabber.exe" which is located in the following path:
C:\Program Files (x86)\Cisco Systems\Cisco Jabber
i hope this helps.

Cisco Jabber for Windows always shows "Away"

Cisco Jabber for Windows (9.0.1, CUPS 8.6.4, UCM 8.6.2, Exchange 2010) always shows status as "Away" for one user. Others seem to be working correctly showing "one the phone", "in a meeting", etc. Tried reinstalling client with no change. If you manually change to "Available", it changes right back to "Away". Anyone have an idea where to look (registry, logs, etc.)?

I am seeing the same problem. I haven't tried a different user to login on the same machine, but I did try closing my client on my primary machine (exited) and then logged in on a different computer with a fresh Jabber for Windows install.
I am running Jabber for Windows Version 9.0.2 Build 9453 on windows 7 64bit primarily, and Windows XP as the second test. Running CUPS 8.6.4 in HA over WAN cluster mode with CUCM 7.1.5 and Unity Connection 8.5.1 ES 16.
Phone presence information does still flow through when I pick up my phone hand set my status changes from Away to On a Call.
When I check the presence diagnostic test for my user, it also reports that I am away.

Cisco Jabber for Windows Voicemail issue

At this I'm in processing of implementation Cisco Jabber UC solution for big Company.
I use CUCM 9.1.2, Cisco IM and Presence 9.1.2, CUC 9.1.2, Cisco Jabber for Windows 9.6.1.
I have issue in Cisco Jabber with VoiceMail Integration - when I leave voice message for any user,
than this message is arrived only him Cisco IP Phone, but not in him Cisco Jabber.
From Cisco Jabber Connectivity status in help menu I see that VoiceMail service is successfully connected
and I see VoiceMail button in Cisco Jabber.
How can I resolve this issue?

Have you configured the UC Service profile on CUCM with both Voicemail server and mailbox servers?

Cisco Jabber for Windows User Photos

CUPS 8.6.3
Jabber Client for Windows Version 9.0.1 Build 8802
I noticed that the Cisco Jabber for Windows Client does not automatically update with the photos that updated in Active Directory.
I had updated a user's photo in AD and noticed that it would not change. I browsed to "C:\Users\<user name>\App Data\Local\Cisco\Unified Communications\Jabber\CSF\Photos" and had to manually delete the user photos in this folder. I exited out of the Jabber Client and restarted the program. When I did this, the Jabber Client crashed, I saved the crash report, and re-opend the Jabber client. This time the client opened properly, and the updated photos were now appearing!
Seems like Cisco would not have set the photos to Cache to the local computer....
Any thoughts?

Yes, Here is a sample .xml script.
<?xml version="1.0" encoding="utf-8"?>
http://www.cisco.com/CiscoJabberSetup.msi
          Cisco
          http://www.cisco.com/web/fw/i/logo-open-graph.gif
          http://www.cisco.com
          Cisco Jabber for Windows
          http://server_name.cisco.com/jabber.png
          http://www.cisco.com/en/US/customer/products/ps12511/tsd_products_support_series_home.html
          Cisco Jabber
          http://server_name.cisco.com/jabber.png
          http://www.cisco.com/web/products/voice/jabber.html
EDI
1
YOURDOMAINCONTROLLER
389
0
ldapaccount
ldapaccountpassword
dc=XXXXXXX,dc=XXXXXXX,dc=com
ipPhone
True
sAMAccountName
http://www.yourinternalwebserver.com/User%20Photos/Profile%20Pictures/sAMAccountName.jpg
true
true
.exe;.msi;.rar;.zip;.mp3
false
presence
The bold is how we pulled photos from a directory on a web server
If you don't have IIS running on a server you can replace
http://www.yourinternalwebserver.com/User%20Photos/Profile%20Pictures/sAMAccountName.jpg
with
\\Your server\c$\PhotoFolder\sAMAccountName.jpg

Contacts search for cisco Jabber for Windows & MAC

Hello,
Please assist on given below query !!
System Deatails of CUCM & IM Presence Server
CUCM:
1> System version: 9.1.1.20000-5
2> VMware Installation: 2 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 4096Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with IM & Presence
IM & Presence:
1> System version: 9.1.1.20000-5
2> VMware Installation: 1 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 2048Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with CUCM
Requirement:
1> User Search base for Cisco Jabber for Windows & MAC Client
2> Will we able to get contacts list(Jabber For windows & MAC) as like "Lotus Sametimes" for all users?
Every reply would highly Appreciated!!

Hi Karthik,
Thanks for your reply!
I have gone through the link but query is different actually, please assist on below query and provide any document links if possible.
1> The contacts does not appear when I perform a search
2> Do I required to integrate LDAP for same? If Yes Then Do I need to perform integration with CUCM Or IM & Presence? Or Only CUCM? Or only IM & Presence? (Please post a link to perform same)
3> Please also provide If any specific system requirement for LDAP server.
4> Is it possible without LDAP integration?
It is really urgent and every post would highly appreciate..........

Cisco Jabber for Windows 10.5 search Contact with two lastnames

Hey Guys,
I have a little problem with the contact search feature of the cisco jabber for windows (Version 10.5.37889)
In my environment I have some Users (secretary phones and users too) which have two lastnames.
Exampleuser1: Firstname: Thomas Lastname: Meier Cisco ....
If a user is searching for Exampleuser1 by lastname (Cisco) the correct contact won't be listed
If a user is searching for Exampleuser1 by firstname (Thomas) the correct contact will be listed
If a user is searching for Exampleuser1 by lastname (Meier) the correct contact will be listed
is there a workaround or something else for resolving my problem?
thanks for reading my question :)

Workaround: "Cisco Meier, Thomas"
Have you looked at enabling wild card searches in jabber-config.xml?

Home Sharing not working between wireless PC's / devices and ethernet wired PC's on the same router.

Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router. I installed a new Verizon FIOS ActionTec MI424WR GigE wireless / ethernet router, replacing the original FIOS router. With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices. With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices. Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
Only the router was changed. No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01. Three PC's are wired and all are running Windows 7. There also is a Windows Home Server connected to the router by ethernet port. It does not run iTunes but does provide WebDAV services to my iOS devices. This works fine. Two PC's are wireless, one running Windows 7 and one running Windows 8. All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point. Two of the wired PC's are connected via a high-speed ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router). All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
Obviously the router seems to be the issue, something between the ethernet and the wireless access point components. I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices. There is no setting that isolates the wireless network. I have done the following:
Read the router user manual and checked all the settings
Rebooted the router and tested.
Turned off the router's firewall and tested.
Home Sharing is turned on all the devices and all use the same Apple ID.
Restarted iTunes and tested.
Verified iTunes is "Allowed" in each PC's firewall.
Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's. I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's. I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
I hope someone may have had a similar problem and has a fix suggestion. I'm stumped! I have a;so contacked ActionTec and awaiting an answer.

Solution from ActionTec is:
Log into your router.
Click the Advanced icon
Cclick Yes
Click on the IGMP Proxy
Select Disable
Click Apply

My computer keeps saying that itunes is not working so i updated my windows and reinstalled itunes but it still doesnt work what do i do?

my computer keeps saying that itunes is not working so i updated my windows and reinstalled itunes but it still doesnt work what do i do?

This link will give service options for your Country ,select from drop down menu
http://support.apple.com/kb/index?page=servicefaq&geo=United_Kingdom&product=iph one
To troubleshhoot restore see document below
http://support.apple.com/kb/HT1808

I can not share file from Jabber for Iphone and Android

Hi guys.
I have:
CUCM9.1/Publisher y Subscriber
System version: 9.1.1.41900-1
Presence/Publisher
System version: 9.1.1.41900-1
Expressway x8.1.1
Cisco Cisco Expressway-E
Expressway x8.1.1
Cisco Expressway-C
Jabber for Android and Iphone 10.6
I do not have "file transfer" and my Iphone an Android.
I don not have "share desktop" from internet on my windows jabber.
The calls and chat is working fine, but when I wante send a file, the option on my iphone is disable.
Why?

Hi dennisalpizar07,
check this:
Jabber for Android officially supports receive BFCP video sharing on TAB devices (normally used for Android Tablets without native calling capability).
The Jabber for Android 10.6 release enters a beta trial on receiving BFCP video sharing on BOT devices (normally used for Android smartphones and phablets)
page 2 of the Cisco Jabber for Android 10.6.x Release Notes.
Hope this helps.

No Audio on either end Cisco Jabber for Windows over Cisco AnyConnect

Our telephony staff is replacing our aging/unsupported VoIP system with a Cisco system and as the network tech, I'm trying to get Jabber for Windows to work over our AnyConnect VPN client. Jabber to Cisco phone and Jabber to Jabber calls work fine within our LAN.
However, when I take a laptop to a separate internet connection and connect to the network via the VPN, I can't get any audio to pass across the system, in either direction. If I call a phone on our LAN using the Jabber client (via AnyConnect), the phone rings and when I answer it, it's just dead air on both ends. If I reverse the process, calling from the phone to the Jabber client, the same thing, Jabber client rings, but dead air both ways once I answer.
Things I can do from the laptop over the VPN connection:
I'm able to get to the phone's web interface using that same laptop.
I can ping the phone as well. In fact, the VPN profile I'm using has full access to the entire VoIP Vlan including all IP traffic (all ~65,000 ports).
Searching the address book also works fine. I can search for staff and it's pulling directly from our Active Directory environment.
Is there any special settings on the firewall that I need to setup to allow the voice traffic (which I assume is RTP traffic)? I tried to add a service policy for RTP traffic, but that didn't seem to work...unless I built it wrong.
Jabber for Windows - 10.6.0
Cisco Anyconnect - 3.1.06079
Cisco 5515-x ASA - 9.2

I was able to resolve this on my own. I thought that SIP traffic needed to be inspected via the global inspection policy in order for it to pass through the firewall. I ran into the same issue with ICMP traffic from an Anyconnect client to LAN devices. I had to enable ICMP in that policy for us to be able to ping LAN devices over the VPN tunnel. So when I saw that SIP was already being inspected by this policy, I moved on looking for other solutions. Then I stumbled deep within a Google search (almost hit the end of the Internet doing so) where someone mentioned that SIP shouldn’t be inspected by that policy. So I unchecked it and bam! Voice is now working over the anyconnect client to phones on the LAN.

HT6114 camera is not working in my mac for skype and facetime

camera is nt working in my mac for skype and facetime calls.there is no option for camera also in my mac...

• If Apple's http://support.apple.com/kb/HT2090
   suggestions do not help you, (the "reset" suggested there
   often restores normal function,) continue with the following.
• Use your Mac's Disk Utility to repair permissions and then
   download and apply the latest Combo Update. For your
   Mac OS X (10.7.5), the latest Combo is http://support.apple.com/kb/DL1582
• Repair permissions again immediately following the system restart
   that completes the Combo update.
Properly applying the Combo version of updates can sometimes correct software problems, but, if your trouble is caused by a hardware problem, there are no user serviceable parts of the camera. For hardware help, contact Apple or an Apple-Authorized Service Provider for service.
(Over time, Apple has changed the built-in camera's name on newer Macs from "iSight" to "FaceTime" and then to "FaceTime HD." Regardless of the name of your Mac's built-in camera, the same info and troubleshooting applies.)

Why does Digital Edition not work in desktop mode for WIndows 8?

I have installed the most recent version of JAVA and then downloaded and installed Digital Editions. I can open Digital Editions in desktop mode but when I select a book I cannot turn the page or move to a new page by any means. The only thing that seems to work is to select a new page and then toggle between full screen and partial.

I don't think ADE uses Java at all.
I run it in desktop mode in WIndows 8 and it reads books and turns pages fine: either using the left-right arrow keys,
or clicking on the forward/back buttons each side of the scrollbar at the bottom of the page.
There are lots of bugs in ADE2.0, and even though that isn't a bug for me it may be for you.
Try replacing ADE2.0 with the older but more reliable v1.7.2.
(You can have them both installed at once if you like.)
Version 1.7.2, it is a little difficult to find, available on Adobe site for Windows and for Mac.
http://helpx.adobe.com/digital-editions/kb/cant-install-digital-editions.html
The forum software is sometimes corrupting the link above. There shouldn't be a blank in 'editio ns.html'. The following redirects to the same page: http://tinyurl.com/diged172

Call/video not working between Cisco jabber for Windows and VCS control C40s

Similar Messages

Maybe you are looking for