Called name display over qsig and H323

Dears,
i'm trying to display the caller name when calling from a cisco ip phone to a siemens phone, and vice versa. the siemens pbx is conneced to the voice gateway through qsig.the gateway is configured as h323 on the call manager. Note that the the calling name is displayed in both ways.
Anyone has a suggestion how to display the calling name?
i'm attaching the running config of the voice gateway,
thanks for your feedback,

Hi,
you can find screenshots and debug in attached piece.
here's an extract of the gw config:
voice service voip
qsig decode
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
supplementary-service h450.12
h323
  h225 timeout ntf 300
  h225 display-ie ccm-compatible
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729br8
voice class codec 2
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729br8
voice class h323 1
h225 timeout tcp establish 5
h225 timeout ntf 300
h225 display-ie ccm-compatible
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn overlap-receiving
isdn protocol-emulate network
isdn incoming-voice voice
isdn map address *. plan isdn type unknown
isdn supp-service name calling ie 40 cs 0 profile Network-Extensions operation-value-tag local
isdn sending-complete
isdn outgoing ie facility
isdn outgoing display-ie
isdn outgoing ie caller-number
no cdp enable

Similar Messages

  • E71 - SUDDENLY: No Caller Name Displays!

    Sometime, within a day or so following my first first sync (using Nokia PC Sync) between my E71and Lotus Organizer, I noticed that NAMES for incoming and missed calls from callers already in my contacts no longer display. Only the numbers. Names (per my contacts list) did display before I did the sync to Organizer. Calls dialed from the contact list still show up as names in the log -- however, the same number dialed from the missed calls list or directly from the screen does not resolve to a name. Only a number shows.
    I'm really perplexed about this, and highly annoyed.
    1) The numbers are NOT/NOT duplicated anywhere in my contacts, and I have NO contacts saved to my SIM card. NONE.
    2) Deleting an entry and then creating a new one from the missed call list (using the same number and name for the new entry) doesn't help. Still no name displayed.
    3) I've noticed VOICE TAGS which I don't ever recall seeing before I synced - maybe they were there, but I don't recall them. And those little pacman icons do rather catch one's eye.
    4) Numbers are not oddly formatted, and in any event, they've not been changed. But something has certainly changed.
    I've read the postings on this problem, and the only hope seems to be a complete deletion of my phone-based contacts, with a restore via PC--> Phone from my Organizer contacts list. I'm reluctant to try this, as the problem began with the sync between the two.
    This is really pretty absurd.
    Any help here, please?

    I agree - it certainly looks like some sort of refresh bug or perhaps some sort of bug linking names for contacts from a particular account.
    I was having problems resetting my password for my Exchange account so I finally just deleted the whole account and re-added it. When I re-added it, I left my Exchange contacts disabled. A few hours later, I was switching back & forth between my Recent Calls and Favorites (accidentally) and suddenly the names for my Favs were replaced by #'s only. Ditto with my Recents.
    After reading your post, I re-enabled the Contacts for my Exchange account and let them sync. Switching back & forth from my Favs & Recents over the next few minutes I began to see my names come back.
    I suppose y'all who are having problems could try to delete your account that many of your contacts are linked to and then re-add and allow sync to happen. No guarantees, but it seemed to work for me.

  • Nokia x6 no caller name displayed

    Hi ,ive just got a nokia x6. I have all my contacts on the sim card. when i get a call the number is displayed but not the name.
     does anyone know how i get the name displayed?
    thanks
       leigh

    Found this little gem online when I had the same problem quote:
    If multiple contacts have the same number in your contacts list and one of them calls you, your phone has no way of knowing which one is actually on the other end of the line and, quite sensibly, just shows the number instead of trying to "guess" who it really is. Now, most phones can store contacts both in their own memory and on the SIM card. If you have the same contact in both locations then that counts as duplicates and you'll never see that contact's name displayed. The cure for this is to use the phone's built-in search facility and to search for the number in question. If you find it more than once then you'll have to delete all but one occurrance.
    unquote:
    It worked for me, my problem was I had numbers I called from abroad with the +44 prefix with the persons name and int (for international dialling)  i.e.  Bill 07.......   then Bill Int +447.....   this meant that as the phone saw 07 and +447 as the same number it did not know if it was Bill or Bill int calling so just displayed the number.
    I just put both the international number and the uk dial number in the same contact under phone and mobile and bingo works a treat.
    Hope this helps

  • NVIDIA display over HDMI and ATI sound over HDMI using one mainboard

    Hello everyone,
    I was curious to know if it is possible to use a setup where I use an NVIDIA card to send display over HDMI to my receiver and at the same time I use an internal ATI chip to send audio over HDMI to the same receiver.
    In my setup it is a GA-MA78GM-S2H mainboard with a built in ATI HD3200 IGP and an NVIDIA 9500GT GPU and I'll be using XBMC as media centre.
    The problem is there is no hardware acceleration support for the display of full-hd (1080p 24) for the ATI chip, whereas NVIDIA using  VDPAU is.
    On the other hand the 9500GT doen not support audio over HDMI (unlike the newer models like GT210 or GT220), I can connect SPDIF to the NVIDIA card to allow some sort of audio over HDMI, but in that case I'll still have the bandwidth limitation associated with SPDIF.
    I tried to set up a box with both NVIDIA and catalyst drivers to use the above functions, but when I try to install catalyst drivers I get a hardware conflict notice that NVIDIA and Catalyst drivers cannot be installed at the same time on the same system.
    AFAIK I need the catalyst drivers (or hd-radeon) in order for also to recognize the device (?)
    Anyone any information if installing both drivers is required and possible? Or are there any other methods to achieve such set up?
    TIA,
    daf art

    Hello everyone,
    I was curious to know if it is possible to use a setup where I use an NVIDIA card to send display over HDMI to my receiver and at the same time I use an internal ATI chip to send audio over HDMI to the same receiver.
    In my setup it is a GA-MA78GM-S2H mainboard with a built in ATI HD3200 IGP and an NVIDIA 9500GT GPU and I'll be using XBMC as media centre.
    The problem is there is no hardware acceleration support for the display of full-hd (1080p 24) for the ATI chip, whereas NVIDIA using  VDPAU is.
    On the other hand the 9500GT doen not support audio over HDMI (unlike the newer models like GT210 or GT220), I can connect SPDIF to the NVIDIA card to allow some sort of audio over HDMI, but in that case I'll still have the bandwidth limitation associated with SPDIF.
    I tried to set up a box with both NVIDIA and catalyst drivers to use the above functions, but when I try to install catalyst drivers I get a hardware conflict notice that NVIDIA and Catalyst drivers cannot be installed at the same time on the same system.
    AFAIK I need the catalyst drivers (or hd-radeon) in order for also to recognize the device (?)
    Anyone any information if installing both drivers is required and possible? Or are there any other methods to achieve such set up?
    TIA,
    daf art

  • Issue with recieving long SMS and Caller Name display

    Hi,
    Im new to the blackberry and  have looked around other forums & technical centre and havn't found any way to solve my issues although  i did find something about caller id problems.
    1) When people send me long SMS i.e over 160 characters long i keep recieving them in separate SMS and it becomes very confusing... i have owned over 7 different phones in the past and this has never been a problem. Is there any way to solve this?
    2) Quite often when someone calls me, i only seem to be able to see the callers number and not the Name, this is frustating as i have no idea who is ringing.
    Hope you can assist me.
    Thanks.

    It helps to give ALL the details of yoru device, such as your OS release on the device and your carrier as well.
    1.  Verizon blocks combined SMS over 160 characters on their BlackBerrys. You should fuss at them. Other carriers don't do this. An alternative for you is the application called "Beyond160", find it in AppWorld.
    2. There could be any one of three solutions... Try these:
    a. Make sure you set your own country code at Phone Dialer Screen > Options > Smart dialing.
    Set your country code in this format: "+xx" where xx = your country code. Some countries have two or three digit Country Codes. Do not place the '+' in your contact's entry.
    * In the US, set this Country Code as "+1", and place your loca area code in the proper box (this normally the default setting in a new BB).
    b. At the same location, change the National Number Length to the number of digits for your country (since some countries will have less than 10 as set as the default in the BB). Find out the total digits, minus the country code. Do not place the '+' in your contact's entry.
    * For example, some countries have a total number to 8 (plus 3 for country code). You would enter "8".
    c. You may have "Content Protection" set on your Address Book.
    Look at Options > Security > General Settings. Scroll down to Content Protection > Include Address Book = NO.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Some menus and folder names displayed in Chinese and some in English

    In one application the menu is displayed in Chinese text. switch to another app and menus are in English.
    Language default is English.
    Also using VLC > Open Files > Browse displays Finder directory with all text in chinese against all icons (home, apps, docs etc).
    I have reinstalled osx 2 times now and having real problems cropping up all the time with parameters being reset, parameters ignored.
    HELP.
    20 years on PC and now 1 month Mac is making me gray.

    In one application the menu is displayed in Chinese
    text. switch to another app and menus are in
    English.
    Language default is English.
    Do Get Info on the icon for that application, hit the languages tab, and make sure only English is checked. If English not available, reinstall the app.
    Also using VLC > Open Files > Browse displays Finder
    directory with all text in chinese against all icons
    (home, apps, docs etc).
    You might want to ask the people who make VLC about that one, if you haven't already.

  • Calling name in UCCX

    Is it possible to set the calling name (display name) when a call is transferred by UCCX script ?

    Hi Paolo
    No, it's not - CLI/N is a bit of a sticking point with UCCX. IN 10.0 you can set the call so it shows the outside caller's actual number, prior to that it shows the CTI port number. You can never 'set' the name.
    Some suggestions:
    1) If you are doing a 'transfer' e.g. call redirect step, rather than routing to an agent, and if you have a small number of 'names' (for example, you take calls for 5 menu options, and want to set that on the call e.g. 'sales', 'cs' or whatever)... you can transfer the call to a CTI RP, name the CTI RP 'Sales' (alerting/display name) and then forward that to the intended extension. The receiving extension would then see 'Forwarded for Sales'. Similar for sending to a hunt group..
    2) If you are routing to an agent with a select step, you can set a CAD workflow to pop up an alert with the name. Or you could just set Enterprise data and add show it in CAD. It doesn't appear on the handset, but is there on the PC screen, and you have the advantage of being able to set it to whatever you want per call.
    Aaron

  • Lumia 900 doesn't support Name Display?

    I was talking with the Rogers representative here in Canada, and he says the Lumia 900 doesn't support Name Display (as opposed to Caller ID).  Is this true?  Could it be possibly added via firmware changes?

    ProfJulie wrote:Have you seen this thread?  Seems like Rogers may need to make a change in their system on their end:
    Yup.. but this is slightly different.
    Here, Caller ID is working fine (I can see the phone# of the caller, and if they are in my Contacts list, then the name/image is displayed) but if it is someone who is not in my Contacts list, then with Name Display enabled, their name (not number) should display on the phone (if they allow it, which most businesses do).
    On my account, Name Display is enabled and works fine on a Samsung Focus S. On my Lumia 900 however, I never see names -- only the caller's phone number.  According to Rogers, Name Display doesn't work on a Lumia 900.
    I can attest the Rogers has the account set up properly, since it works on the Samsung Focus S.

  • Calling name presentation cucm

    Hi
    I have a problem with calling name presentation when a call is transfered from one of my secretaries to another internal user, the original Called Party details are shown on the recieving phone.
    This is the secretaries query :- "If I picked up an external call that has bounced from my Manager cathy's phone and the caller requests to speak to someone else (i.e. Jim) as Cathy is unavailable, when I call Jim's extension (without ending my external call) it tells Jim that it is Cathy calling him and not me calling".
    So the wrong calling party name is shown (the original called party, rather than the transferor) ?
    Thanks
    Paul

    Hi Paul,
    Can you give a try for below settings:
    When a call routes through a translation or route pattern, routes to a Call Forward All or Call Forward Busy destination, or gets redirected through a call transfer or CTI application, the connected number display updates to show the modified number or redirected number.
    To turn off phone display updates so that the phone displays only the dialed digits, set the Cisco CallManager service parameter "Always Display Original Dialed Number" to true. When this service parameter specifies true, the originating phone displays only the dialed digits for the duration of the call.
    You can choose if the name for the original dialed number or the number after translation is displayed using the Cisco CallManager service parameter called "Name Display for Original Dialed Number When Translated". The default setting displays the name for the original dialed number before translation. This parameter is not applicable if the "Always Display Original Dialed Number" service parameter is set to false.
    Regards,
    Nishant Savalia

  • Display both company AND name in contacts, incoming calls, messages, etc

    Is there no way to have both a person's full name, AND company appear on the display of contacts and incoming calls??
    I have over 2,000 contacts in my address book, many from the same company, and many with the same (or similar) names.
    When someone with a very common name calls or texts, it's impossible for me to remember who they are without listing their company as well. If I have both Sam Michaels and Samantha Mitchells in my address book, sometimes the only way to distinguish between the two is knowing that Sam works for Viacom and Samantha works for Universal.
    I've heard that the only way to do this is to include the company name in the person's main "name" field. This is problematic because A) it would take me a million years to go through and personally edit all of my 2k+ contacts, and B) this is completely counter-intuitive of having the company/office/job title lines available as fields in the address book in the first place. 
    Does anyone know a way around this at all?? Apple really needs to find a way to fix this, as it's super inconvenient for business professionals. This is just another one of my many frustrations with Apple products being not intuitive for workers in the corporate world.

    I'm not aware of a way to do this, however I'm certain that when my phone rings, it shows the person's name and company information that I have written in contacts. I've not taken time to check lately, but that seems to be the case for contacts that have a company name in them. Ones that do not have a company name show the person's name and then the label for the phone number they are using, such as home, work, mobile, etc.
    Otherwise, feedback to Apple goes HERE, and then just click on the appropriate subject.

  • Sony mw600 dont display music id and caller name

    I am usinh sony mw600 with my phone (huawei mate android 4.2.1) and the headphone dony show the track id ornthe caller name, please help

    Some Android phones does unfortunately not support sending this information to a bluetooth headset and in this case you can usually only see the number when someone calls you.
    I recommend that you contact Huawei to see if they are aware of this.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Caller name and number not displaying on my iphone 4s

    Caller name and number not appearing on my iphone 4s..

    Hello mukundaniyengar,
    We've an article that provides a few additional troubleshooting steps that may help get your iPhone's speaker working again.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/TS5180
    Cheers,
    Allen

  • How can I display the first and last name using a paramater as employee ID?

    Hi SAP,
    I have a parameter that is called {? Employee ID}.   What I want to do is display the first and last name based on the employee ID value entered in {? Employee ID} in the page header of the report.  Right now, when I put the following formula in the page header only some pages get the right result while other pages dont....
    if table.employeeid = {? Employee ID} then
    table.firstname" "table.lastname
    It appears as though if the first record in the details section on the beginning of each page happens to be the employee under {? Employee ID} then it prints it correctly, if it isn't I get a null value in the page header.
    Anyone have any ideas?
    Z

    Hi Try this,
    Whileprintingrecords;
    if ={?EmpID} then
    Also check the option "Default values for null" in the formula editor.
    Regards,
    Vinay

  • How to display name of the table and the description and the table type

    Hi,
    Can you people tell me how to display the name of the table and the description and the table type (View, structure, etc...) used in the program.
    I want to display in a list.
    Kind Regards

    use this program
    TABLES : TSTC, tstct.
    TABLES : DD03l, DD02l.
    DATA : Program like sy-repid.
    DATA : BEGIN OF I_FINAL OCCURS 0,
    tabname LIKE dd02l-tabname,
    TABCLASS LIKE dd02l-tabCLASS,
    TEXT LIKE DD02T-DDTEXT,
    END OF I_FINAL.
    DATA : BEGIN of ITAB Occurs 0,
    name like dd02l-tabname,
    END OF ITAB.
    DATA : TCD(100) TYPE C.
    DATA : var1 LIKE dd02l-tabname.
    DATA : DESC LIKE TSTCT-TTEXT.
    selection-screen skip.
    SELECTION-SCREEN : BEGIN OF BLOCK b2 WITH FRAME TITLE text-002.
    PARAMETERS : r1 RADIOBUTTON GROUP r DEFAULT 'X'.
    Parameters : Tcode like sy-tcode.
    selection-screen skip.
    PARAMETERS : r2 RADIOBUTTON GROUP r.
    Parameters : Prog like sy-repid.
    SELECTION-SCREEN END OF BLOCK b2.
    SELECTION-SCREEN BEGIN OF BLOCK B1 WITH FRAME TITLE text-001.
    select-options : Type for dd02l-tabclass .
    SELECTION-SCREEN END OF BLOCK B1 .
    at selection-screen.
    if r1 = 'X' and Tcode is initial.
    message e001(00) with 'Enter Transaction Code' .
    elseif r2 = 'X' and Prog is initial.
    message e001(00) with 'Enter Program Name' .
    endif.
    START-OF-SELECTION.
    if r1 = 'X'.
    Prog = ' '.
    select single * from TSTC where tcode = tcode.
    if sy-subrc = 0.
    program = TSTC-PGMNA.
    select single TTEXT from tstct into desc where tcode = tcode and SPRSL = 'E'.
    else.
    Write :/ 'Invalid Transaction Code'.
    exit.
    endif.
    elseif r2 = 'X'.
    Tcode = ' '.
    program = Prog.
    endif.
    CALL FUNCTION 'GET_TABLES'
    EXPORTING
    PROGNAME = Program
    TABLES
    TABLES_TAB = itab.
    if itab is initial.
    skip.
    skip.
    skip.
    skip.
    skip.
    WRITE :/40 'No Data Found' color 6 INTENSIFIED OFF.
    ELSE.
    PERFORM : categorize.
    endif.
    END-OF-SELECTION.
    LOOP AT I_FINAL.
    WRITE :/4 I_FINAL-tabname COLOR 2 INTENSIFIED OFF NO-GAP HOTSPOT ON, 35 I_FINAL-TABCLASS COLOR 2 INTENSIFIED OFF NO-GAP,
    50 I_FINAL-TEXT COLOR 2 INTENSIFIED OFF NO-GAP.
    ENDLOOP.
    AT LINE-SELECTION.
    TCD = SY-LISEL.
    var1 = TCD+3(30).
    set parameter id 'DTB' FIELD VAR1.
    call transaction 'SE11' and skip first screen.
    TOP-OF-PAGE.
    WRITE :/45 'TABLE DETAILS RELATED TO THE TRANSACTION CODE' COLOR 7 .
    WRITE :/2 'DATE : ' COLOR 1, SY-DATUM COLOR 1 INTENSIFIED OFF NO-GAP.
    WRITE :/2 'TRANSACTION CODE : ' COLOR 1, Tcode COLOR 1 INTENSIFIED OFF NO-GAP.
    WRITE :/2 'TCODE DESCRIPTION : ' COLOR 1, desc COLOR 1 INTENSIFIED OFF NO-GAP.
    WRITE :/2 'PROGRAM NAME : ' COLOR 1, PROGRAM COLOR 1 INTENSIFIED OFF NO-GAP.
    SKIP 1.
    WRITE :/1(140) SY-ULINE.
    WRITE :/4 'TABLE NAME' COLOR 5 INTENSIFIED OFF NO-GAP,35 'TABLE TYPE' COLOR 5 INTENSIFIED OFF NO-GAP,
    55 'DESCRIPTION' COLOR 5 INTENSIFIED OFF NO-GAP.
    WRITE :/1(140) SY-ULINE.
    *& Form categorize
    text
    --> p1 text
    <-- p2 text
    FORM categorize .
    SELECT dd02ltabname dd02ltabCLASS DD02T~DDTEXT
    FROM dd02l INNER JOIN DD02T ON dd02ltabname = dd02Ttabname
    INTO TABLE I_FINAL
    FOR ALL ENTRIES IN itab
    WHERE DD02L~TABNAME = ITAB-NAME AND TABCLASS IN TYPE AND DDLANGUAGE = 'E'.
    if sy-subrc <> 0.
    skip.
    skip.
    skip.
    skip.
    skip.
    WRITE :/40 'No Data Found' color 6 INTENSIFIED OFF.
    endif.

  • Fbl1n and fbl5n line item wise display the cutomer and vendor name

    Hi,
    My user is asking report for fbl5n and fbl1n line itemwise dispaly vendor and customer.See the report for one time vendor and customer name displaythe line item wise display in FBL!N/FBL5N. but not the display the regular vendors/customer.So one time table name BSEC
    Please advise
    Regards.
    Edited by: yps y on Nov 13, 2008 1:26 PM

    Hi,
    line item reports FBL1N/FBL5N are reading the line items (wow, what a big surpise ) and displaying information on line item level.
    As the vendor/customer name is NOT stored in the line items, you cannot display this in the lines (along with other item level information., like amount, posting key, doc.type, etc.). You may find a field called "Name 1) in the field catalog when configuring the ALV layout but this is empty for normal customers/vendors. It is only filled in for one time (Cpd) customers - the reason is as explained above: for these special accounts, the name IS stored on line item level (it varies from item to item),, that's why it can be read and displayed in the items.
    Now how about normal customers/vendors?
    You have to activate Business Transaction Event 1650 and implement a simple code so that depending on the account type (D = customer, K = vendor), you get the business partners name from table KNA1 / LFA1 and put it into field Name1.
    Hope that helps, points welcome
    Csaba

Maybe you are looking for