Caller ID problem between 2 PBX's across Cisco VoiP connection

Hi all,
I have two Cisco 2811 Routers connecting 2 Avaya Index PBX's via T1/E1 cards (configured for E1)across a LES 10 circuit. Everything works fine but the problem i have is when phone1 (John) at site A dials phone2 (James) a site B, the incoming number is shown but not the name of the person. When 2 calls are made within a site, the name of the calling party is shown (not the directory number). Can someone please shed some light on if this is possible across the VoiP connection and how i would configure it. I have attached the configs to help.
Thanks in advance,
Gary.

Ideally there should not be any line code violations on the data T1 at all.
Violations are at the data T1 and the voice T. And they shud be avoided.

Similar Messages

Communication problem between ASA 5510 and Cisco 3750, L2 Decode drops

Having problem with communication between ASA 5510 an Cisco Catalyst 3750.
Here is the Cisco switch port facing the ASA 5510 configuration:
interface FastEthernet2/0/6
description Trunk to ASA 5510
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 131,500
switchport mode trunk
switchport nonegotiate
And here is the ASA 5510 port configuration:
interface Ethernet0/3
speed 100
no nameif
no security-level
no ip address
interface Ethernet0/3.500
vlan 500
nameif outside
security-level 0
ip address X.X.X.69 255.255.255.0
There is a default route on ASA to X.X.X.1.
When I try to ping from ASA X.X.X.1 i get:
Sending 5, 100-byte ICMP Echos to 31.24.36.1, timeout is 2 seconds:
Also in the output of show interface eth 0/3 on the ASA i can see that the L2 Decode drop counter increases.
I have also changed the ports on the Switch and ASA but the same error stays.
Any thoughts?

I don't see anything wrong with your trunk configuration; I have a similar one working between an ASA 5520 and a Catalyst 3750G.
Maybe you should adjust the "speed 100"? In my experience, partial autoconfiguration results in duplex mis-matches, which results in dropped packets.
I'd try removing the "speed 100" and letting the ASA port autonegotiate with the switch. Alternatively, have both sides set
speed 100
duplex full
and see if things improve.
-- Jim Leinweber, WI State Lab of Hygiene

Failure to upgrade Cisco Unity Connection 8.6.2 to 9.1.2

Hi everybody.
Has someone that can help me with follow problem?
I making a Cisco Unity Connection upgrade from version: 8.6.2.20000-76 to 9.1.2.10000-28. But unfortunately we can't sucessfull to make this process.
On the finish of this process, I can see this outup error:
11/23/2013 12:28:55 upgrade_manager.sh|Cleanup exiting - Cached Data: [Vendor= VMware, Inc.
HWModel=VMware
CPUCount=2
CPUType= Intel(R) Xeon(R) CPU E5-2643 0 @ 3.30GHz
CPUSpeed=3300
MEMSize=6144
BIOSVer=PhoenixTechnologiesLTD 6.00 06/22/2012
ObjectId=1.3.6.1.4.1.9.1.1348
OSVersion=UCOS 5.0.0.0-2
SerialNumber= VMware-56 4d e0 4f 4d 85 87 7b-eb 22 0e 52 a7 73 1a 22
VendorOID=1.3.6.1.4.1.674]|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Cleaning up download...|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Cleanup upgrade source area.|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Ejecting DVD (/dev/sda1)|<LVL::Debug>
11/23/2013 12:28:55 upgrade_install.sh|Removing /common/download/9.1.2.10000-28|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Started auditd...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Started setroubleshoot...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Changed selinux mode to enforcing|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Cleaning up rpm_archive...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Removing /common/rpm-archive/9.1.2.10000-28|<LVL::Info>
11/23/2013 12:29:00 upgrade_install.sh|IOWAIT monitor stopped|<LVL::Info>
11/23/2013 12:29:00 upgrade_install.sh|File:/usr/local/bin/base_scripts/upgrade_install.sh:599, Function: main(), Upgrade Failed -- (1)|<LVL::Error>
11/23/2013 12:29:00 upgrade_install.sh|set_upgrade_result: set to 1|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|is_upgrade_lock_available: Upgrade lock is not available.|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|is_upgrade_in_progress: Already locked by this process (pid: 14477).|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|release_upgrade_lock: Releasing lock (pid: 14477)|<LVL::Debug>
Best Regards,
Claudio Costa
A mensagem foi editada por: Claudio Costa

Tks Manish, I just perform a restart on the both nodes on my CUC cluster and after that I did can install this upgrade patch.
Also is very important install the upgrade patch on all servers of the cluster before perform a switch-version on the publisher and then on the others nodes.
Best Regards,
Claudio Costa

NEC PBX Interaction with Cisco Call Manager

Hi,
We have a new building that we want to connect to our network and thinking of Callmanager to be installed and linking it to our NEC PBX.
Need some pointers on how am I going to go about doing that. Documents and examples will be really appreciated

Hi!
Here are some documents that might help:
*** NEC 2400 ICS PBX with CallManager using 3640-T1 MGCP Gateway ***
http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_troubleshooting_guide09186a00808b6024.html
*** Cisco Unified CallManager Release 5.0-PBX Interoperability: NEC IPX2400 R15 to a Cisco CMM Using T1-PRI QSIG with MGCP ***
www.cisco.com/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/522832nt.pdf
The second link includes info on SW and HW requirements as well as features supported.
*** Cisco Unified CallManager Release 5.0-PBX Interoperability ***
www.cisco.com/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/248705nn.pdf
HTH, if it does please rate!
Tere :)

TS3367 FaceTime has a problem with calling (audio, video) between two devices when they are in the different networks.

Hi,
I have a problem with calling by FaceTime when me and my friend are in the different networks.
When i call to another device I see this call on that device and tap to the answer button after that i see a message "connecting" but the first device is trying to call in during about 1 minute and finish the call.
But if both of the devices have connected to the one network (wifi) it works correct.

Actually, it started working fine when I told it to capture
sound at 11kHz.. I should have tried that first, before making a
fuss here, sorry. Looks like some weird glitch, a driver problem
maybe, but anyway, switching to 11kHz seems to have solved
it.

Problem between SOAP Sender and JDBC Receiver

Hi,
I have a asynchronous scenary between SOAP Sender and JDBC Receiver.
The idea is sending an ID for updating one register.
Table structure is:
TABLE AS_PERSONA
    (P_RUT                         VARCHAR2(10) NOT NULL,
    P_NOMBRE                       VARCHAR2(50),
    P_APELLIDO                     VARCHAR2(50))
The ID is the P_RUT field.
The structure of message that I send by SOAP, is the following:
<SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
     <SOAP-ENV:Body>
          <m:MT_CONS_SOAP xmlns:m="urn:prueba:voliva">
               <CONSULTA>
                    <P_RUT>15445</P_RUT>
               </CONSULTA>
          </m:MT_CONS_SOAP>
     </SOAP-ENV:Body>
</SOAP-ENV:Envelope>
The JDBC receiver structure is:
<?xml version="1.0" encoding="UTF-8"?>
<ns0:MT_CONS_PERSONA xmlns:ns0="urn:prueba:voliva">
     <Statement>
          <AS_PERSONA action="UPDATE">
               <table>AS_PERSONA</table>
               <access>
                    <P_NOMBRE>DELETE_BY_XI</P_NOMBRE>
                    <P_APELLIDO>DELETE_BY_XI</P_APELLIDO>
               </access>
               <key>
                    <P_RUT>15445</P_RUT>
               </key>
          </AS_PERSONA>
     </Statement>
</ns0:MT_CONS_PERSONA>
When I do a call to SOAP by XMLspy, it returns a message without data, that means succesfull reply.
I see message monitor and see the succesfull flag. But in the database it doesn't update the register.
This scenario was proved using the File Sender and same JDBC Receiver, then result was succesfull.
I proved SOAP Sender with a File Receiver, storing information from SOAP sender in an archive, and works well.
Then I imagine that exist some problem between SOAP and JDBC. what could be happening ?
Thanks.

Hi,
Looks like the problem is with the JDBC receiver...try updating the value in the table by using a File-JDBC scenario..does it work..check the adapter monitor in RWB..
Regards,
Sushumna

Incoming International calls receiving problem.

Hi Team,
I have ISDN PRI E1 connection and i am able to recieve all international calls except two DID number. But I am able to receive national calls
without having any problem. Also noticed that We are able to recieve international calls from certain countries in these DID number.
Also noticed that call is hitting in the gateway and getting debug isdn q931 output with proper digit and Isdn Type:International.
For testing we replaced the phone with another,but issue has same.
Let me know either is there any problem with PBX system or problem with Service Provider.
Thanks in advance for your help!!!!
Best Regards,
Febin S

Hi
Provide the debug outputs " debug isdn q931" and "debug voip ccapi inout" when the incoming call is been made.
This will help you to identify the Release Cause for the Call, based on that you can decide the call failure reason while hitting
the Gateway.

NFS problem between RedHat Client and Solaris Server

Hi all, we are experiencing a problem between a RedHat client and a Solaris 10 server. For the purposes of this post, I'll call the Redhat client server A and the Solaris 10 server B.
Server B is exporting a filesystem that server A is trying to mount. Server A can successfully mount the exported file system, however, strange things are happening. If I change to the exported mount point on server A and create a file, the file is owned by nobody:nobody, not the user that created the file.
A look at the file on server B shows the file has the correct UID and GID (ie the UID & GID of server A).
The fstab file on server A looks like this:
serverB:/data /data nfs4 rsize=32768,wsize=32768,hard,nointr,rw,bg,actimeo=0,timeo=300,suid 0 0
Does anyone have a explanation for this?
NB: There is a firewall between server A and server B. A firewall rule is in place to allow traffic between the two servers on port 2049
Stewart

Hi
If I change to the exported mount point on server A and create a file, the file is owned by nobody:nobody, not the user that created the file.On a NFS share, for security reasons, you normally dont have root provileges.
A file createt as root user will be mapped to nobody:nobody.
The behaviour you see is correct.
If you want the file to be createt as root, you have to export the filesystem with -o ro,anon=0
NFSv3 will be blocked by your firewall.
Franco

Cisco Unity Connection 8.6 problem with greeting upload

Hello at all,
i have a realy strange Problem.
I want to upload a Greeting (*.wav-file) to a Call Handler, everything looks fine after uploading and i can also hear (Playback) the massage on the Computer and on my Phone. So i save the Config. After that i want to hear the massage after calling the Call Handler but i hear only "sorry, "CallHandlerName" is not Awailable".
If i make some checks everything looks ok, i have 2 User with sysadmin-role - both can Playback the massage via the Webpage.
But if i take the Phone and call the "Greetings Administrator" - there is no personal Greeting on this Call Handler - and thats my Problem.
If i Record a new massage with the Phone (in the Greeting Admin) it is working - after Uploading a new File (Codec is ok) i can Playback the new file but after Calling the CH, i hear the Massage which i have recordet with the Phone - not the Uploadet. But on the Webpage i hear the Uploadet file.....
Whats wrong????
And yes, i have set this 2 Users as Call Handler Owner.
What should i do??
Please can anyone help me in this case.....
kind regards
Markus
EDIT: I have also the Problem, that i can´t upload a File for a User - only the User self can Upload a Greeting, if do this with one of the 2 Admin-Accounts i hear also the System-Massage "sorry, -USERNAME- is not awailaible" and not the uploadet file - at the Webpage i hear the uploadet Massage - it seems to be the same Prob as with the CallHandler. Is it a JAVA-Problem mabye? I have Java JRE Version7 update7 installed and IE8 as Browser....
Certificate is installed, and the CUC is a trusted site......

Hi Markus,
It could be this bug;
CSCto92753 - Unable to upload wav files and save as greeting or send as message
Description
Symptom:
Unable to upload an existing wav file, or create a new recording using the PC microphone and save as greeting, voice name, or send as message. In the case of trying to send as a message, the user receives a "Failed to Send Message" error.
You might see Failed to Record Name if attempting to overwrite a Call Handler with a file.
You might also see Unable to save recording due to SSL certificate error.
Conditions:
Cisco Unity Connection versions 7.1(5)ES45, 8.0(3)ES27, 8.5(1)ES37
When using either the Cisco Unity Connection Administration (CUCA) or the Cisco Unity Connection Personal Communications Assistant (PCA) web applications to upload an existing wav file, or create a new recording using the PC microphone and save as a voice name, greeting, or send as a message.
In the client side Java Console logs, you see the following exception:
Exception in thread "Timeout guard" java.security.AccessControlException: access denied (java.net.SocketPermission 10.93.231.234:8443 connect,resolve)
Workaround:
In your client side JRE security profile file....commonly named:   java.policy...add the below entry. Will need to use the ipaddress of the Connection server (for a cluster, put an entry for each of publisher and subscriber).
permission java.net.SocketPermission "10.93.237.101:8443", "connect,resolve";
If get a permission error when trying to modify java.policy, then you may need to set the permissions of the file to not inhearent permissions from it's parent and not be read-only. (aka by default the entire JRE folder is read-only but you need to modify a file within it).
A good article on the Sun website with more detail on the workaround:   http://java.sun.com/developer/onlineTraining/Programming/JDCBook/appA.html
Details
First Found in:                          (4)
8.6,7.1(5)ES44,8.0(3)ES27
8.5(1)ES37
Status:
Terminated
Last Modified:
Aug 12,2012
Product:
Cisco Unity Connection
Platform:
Dependent
Severity:
3 - moderate
Cheers!
Rob
"May your heart always be joyful
May your song always be sung" - Bob Dylan

Connection Problems Between iChat 3 and iChat 4 Workaround

Maybe this info will help others:
iChat 4/Leopard users must initiate video chat to iChat 3/Tiger users:
I have discovered that if an iChat 4/Leopard user initiates the video chat to an iChat3/Tiger user, it works, but if the iChat3/Tiger user initiates the video chat with an iChat 4/Leopard user it fails with a message saying that the receiver declined the invitation (even if the receiver tried to accept). This happens on a LAN as well as across the Internet.
Likewise, to make conference video chats, make sure the iChat 4/Leopard user initiates, then adds the other parties.
This post is NOT about iChat Server, although the problem occurs there too. If you are using iChat Server (part of OSX Server) see http://discussions.apple.com/thread.jspa?messageID=5995966 ).
Hope this helps.
ppj

Hey.
I found how to work around combatible problems between 1.3 and 1.4. For user, that want to save thier DynamicTree.java (http://java.sun.com/docs/books/tutorial/uiswing/components/example-swing/index.html)
Use follow code (I using Externalizable):
protected DefaultMutableTreeNode rootNode=null;
protected DefaultTreeModel treeModel=null;
public void writeExternal(ObjectOutput stream) throws IOException
{ stream.writeUTF(rootNode.toString());
    Vector values = new Vector();
    Object root = treeModel.getRoot();
    // Save the root, if its Serializable.
    if(root != null && root instanceof Serializable)
    { values.addElement("root");
      values.addElement(root);
    stream.writeObject(values);
public void readExternal(ObjectInput stream) throws IOException
{ thisModel.removeAll();
    thisModel.setVisible(false);
    try
    { String title=stream.readUTF();
      rootNode = new DefaultMutableTreeNode(title);
      Vector values = (Vector)stream.readObject();
      int indexCounter = 0;
      int maxCounter = values.size();
      treeModel = new DefaultTreeModel(rootNode);
      if(indexCounter < maxCounter && values.elementAt(indexCounter).equals("root"))
      { TreeNode root = (TreeNode)values.elementAt(++indexCounter);
        treeModel = new DefaultTreeModel(root);
        indexCounter++;
      // kode for setting the tree start here
    catch (ClassNotFoundException e) {}
}Hope, this is to use :-)
Hi from
Super Bomba

Hi Team, I wuold like to know if you have any app to make Firefox OS working with cisco Call Manager 10.5. Something like Cisco Jabber for Android or iOS.

I'm interesting on buying a Firefox Smart Phone, but
I would like to know if are any app to install on Firefox OS smart phone in order to work with cisco call manager 10.5.
Something like Cisco Jabber for Android o iOS.
Thanks,

Hi Itech,
If Cisco Jabber has a webapp, or mobile version of their website available, you should technically be able to access it through Firefox OS.
You may also search Firefox Marketplace for an alternative solution:
* [https://marketplace.firefox.com/]
- Ralph

Communication problem between NetBeans and Tomcat

hi!
i got a quite mysterious problem. here is what happens:
- i start NetBeans 5.5.1 (the first time)
- i want to debug my JSF-Project, the Debugger starts
- After a few seconds the debugger waits for tomcat (it sais: "Waiting for Tomcat...") and tomcat starts
- Again after a few seconds the tomcat-debugger-output sais "Tomcat startet in 3333 ms".
okay.
when i enter http://localhost:8084/ in my browser i get the tomcat homepage, so the server has definitely started! But nothing happens in NetBeans and nothing happens with my project....
In the lower-right corner i see this blue working-bar that sais "deploying project" but nothing happens. The Project-Debugger-Output still sais "Waiting for Tomcat..." but nothing happens...
And after something around 3 minutes (i guess it's a timeout) i get the error "Starting of Tomcat failed." But is HAS started, i can login to the Administration-Area in my browser!
so i guess there is a communication problem between netbeans an tomcat. Netbeans waits for a message from tomcat but tomcat doesn't send it..or netbeans doesn't understand it.
But the story goes on:
When i press the debug-button a second time it takes only a few seconds till i get the message: "Tomcat server port 8084 already in use". OF COURSE! Because Tomcat has already startet and can't be stoped by NetBeans.
i'm trying to solve this problem for 4 days now, so i would be very happy if anyone has an idea where to start/continue the search...
thanks,
flo.
some system-info:
- windows vista business 32-bit
- no firewall is running
- AntiVir Personal Edition IS running
- Yahoo Widgets Engine IS running
- no other software is running
and finally the tomcat-log:
Using CATALINA_BASE: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base
Using CATALINA_HOME: C:\Program Files\NetBeans\enterprise3\apache-tomcat-5.5.17
Using CATALINA_TMPDIR: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base\temp
Using JRE_HOME: C:\Program Files\Java\jdk1.5.0_12
Listening for transport dt_shmem at address: tomcat_shared_memory_id
21.09.2007 18:27:50 org.apache.catalina.core.AprLifecycleListener lifecycleEvent
INFO: The Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: C:\Program Files\Java\jdk1.5.0_12\bin;.;C:\Windows\system32;C:\Windows;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Program Files\QuickTime\QTSystem\;C:\Program Files\ThinkPad\ConnectUtilities;C:\Program Files\Common Files\Teleca Shared;C:\Program Files\Common Files\Adobe\AGL;C:\Program Files\MySQL\MySQL Server 5.0\bin;C:\Program Files\cvsnt;
21.09.2007 18:27:50 org.apache.coyote.http11.Http11BaseProtocol init
INFO: Initializing Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:50 org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 1862 ms
21.09.2007 18:27:50 org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
21.09.2007 18:27:50 org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.17
21.09.2007 18:27:50 org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
21.09.2007 18:27:53 org.apache.coyote.http11.Http11BaseProtocol start
INFO: Starting Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:54 org.apache.jk.common.ChannelSocket init
INFO: JK: ajp13 listening on /0.0.0.0:8009
21.09.2007 18:27:54 org.apache.jk.server.JkMain start
INFO: Jk running ID=0 time=0/31 config=null
21.09.2007 18:27:54 org.apache.catalina.storeconfig.StoreLoader load
INFO: Find registry server-registry.xml at classpath resource
21.09.2007 18:27:54 org.apache.catalina.startup.Catalina start
INFO: Server startup in 3626 ms

As i wrote before, the same problem occured for me. I have found a solution which is : Go to tools menu and then select options . In the proxy info, select No Proxy.
I hope this help you

Wireless Communication problem between HP Photosmart C309g and Linksys E2500 router

Hello,
I used C309g connected to DLink Dl-624 router (wireless connection) and everything was working correctly. Now I changed the router to Linksys E2500 (dual band router) and I've got strange problem I cannot fix.
The printer connects to router, obtaint IP address and network report does not indicates any problem. Also HP Print & Scan Doctor does not report any problem.
But when I try to print from my laptop, the pint start and is quickly broken, and I've got the message that printer is diconnected. The printer stops. When I leave it for a coupl of minutes, the printing starts and after few lines stops again with the same message on the laptop.
When I return to DLink router, everything works correctly.
I tried with 4 different laptops, with different operating systems, and i've gor the same issue. But the laptops communicates well, the network does not break..
I enforced router to use IP reserved number for the printer, used the same IP range and number for my network and printer on Linksys and DLink, does not help. I've turn off firewall on the router - does not help. I've change the channel range for 2.4 GHz network to 20MHz only - does not help.
What would be the problem with it? Is there something related to dual-band? Any idea?

Well, I did not install the printer drivers from cd, I did it from the Hp webpage. Looking for the potential problems I reinstall the drivers and it did not helped. I also turn off the firewall router application and it also did not help.
I suspect I have the printer firmware up to date e.g my version is WHM1FN0931BR.
I've made some test with router settings: switch from automatic WPS configuration to manual and tried network mode as wireless b only (default was mixed). This makes the communication between router and printer continuous (no breaks), I could normally scan documents directly to network drive, but could not print at all: the printing option on my laptop pops up, and looks like document was sent to nowhere.. printer did not start to print at all. But other network devices starts to experience connection breaks and performance issues. When I returned to mixed mode, the communication between network devices returns to normal operation, but not with the printer - where I experiences original problems.
My network is quite complex - 4 laptops and 2 TV sets communicates (wireless or LAN 100mbit cable ) via cental router with NAS server (with DLNA) and internet (DSL cable modem). Router also works as DHCP server, where any server type devises (e.g my printer) has reserved IP addresses (based on MAC number). No matter if I try to print from wireless or via LAN cable laptop, no matter what OS is on laptop. I have even tried to connect the printer via LAN (forcing DHCP to give the LAN pronter the same IP as was previously for wireless ), and stil the same: communication is broked and the print starts and suddenly stops.., then starts angain after few minutes - and stops (the same problem as wireless). So I do not understand what the hell is going on. Rest of my network works perfect .. except this printer.. Any other idea, what coul be the issue?

Export or view the chat transcript between operators on the Cisco agent console

Hi All,
Is there a way I can export or view the chat transcript between operators on the Cisco agent console?
I have UCCX7 which would be migrated to 8.5 Soon.
Thank you,
Hamed

Hi
Unfortunately not - they don' t make it in to the DB or any other central repository.
It would be possible to write a Windows or Powershell script to collect the files and place them on a central file share and then do with them as you wish, but this would be up to you to design and implement.
Regards
Aaron

Problems between Xcelsius and WebDynpro for Java

How should I do to show Xcelsius in WebDynpro for Java?
How should I transport data between Xcelsius and WebDynpro?
How should I control WebDynpro with Xcelsius?For example,firing plugs in Xcelsius like in WebDynpro to change one view to another.
How should I do to execute a Java method in Xcelsius?For example,scheduling a job on clicking a button in Xcelsius.
Besides these,I also want to know the same problems between other BOE contents and WebDynpro for Java.
Regards,
Abe

Hi Pradeep:
Well that purely depends on the business application (project) your client is proposing. Following are very few factors which will drive for creating web-based applications:
VC: it's a UI modeling tool (non-programming) for creating rapid creation of web-based applications.
WD: its a powered by Java and ABAP with which you can create robust business applications.
If your client is very choosy about rapid application development, reporting, rich user interface, to reduce TCO then VC is the choice. Or if the project contains typical integration with SAP and non-SAP systems, complex business logic development, integration with WCM systems...etc then WDJ is the option.
If youve some sort of custom development with facilitating the Development Infrastructure (NWDI) then WDJ is the only option I could say.
We hope with NW CE 7.1.1(referred by Priyanka Singh) tighter integration between these TWO tools may over come the ambiguity of using them.
Tnx,
MS

Caller ID problem between 2 PBX's across Cisco VoiP connection

Similar Messages

Maybe you are looking for