CallerID problem from PSTN
Hi,
I have a very strange problem with callerID from my PSTN.
The lines from the PSTN is connected to a vic2-2fxo card. I PSTN has callerID enabled which I can see whenever a caller calls on the telephone box but when the line is placed on the fxo, it does not display on the IP phones.
When I connected another line from a different PSTN, I get callerID displayed on the IP phones.
When I debug, the vic receives request for the callerID and displays a lenght error for the callerID and displays callerID failed.
PSTN does not know what to do as they're sending callerID.
I'll appreciate everyone's input on this with a fair rating.
TIA,
Kayode
Thanks to all for your responses.
I finally got it resolved. I still believe its a bug in the IOS.
Solution:
I'm running CME4.0 on 2811 but since the 2811 didn't have DSPs, I had to install FXO on 1760V that had DSP chip. This was how the problem started with CallerID working with some PSTN while it didn't work with other PSTNs.
The problem got resolved after I installed PVDM2 on the 2811 and moved the FXO card to the 2811.
The problem does not have anything to do with MGCP or ISDN.
Regards,
Kayode
Similar Messages
-
Problem with incoming call from pstn
Hi,
we have a 2610XM router with CCME 3.2 and 4 bri
and we don't redirect incomming call from pstn on a internal IP Phone.
which command for redirect call ?
my isdn number (french) is 0156838050
and when we call this number with my mobile (number 0685284832), look this debug
debug isdn q931:
Mar 22 12:53:46.350: ISDN BR1/0 Q931: Ux_DLRelInd: DL_REL_IND received from L2
*Mar 22 12:53:46.378: ISDN BR1/0 Q931: RX <- SETUP pd = 8 callref = 0x73
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Calling Party Number i = 0x2083, '685284832'
Plan:Unknown, Type:National
Called Party Number i = 0x81, '8050'
Plan:ISDN, Type:Unknown
Sending Complete
*Mar 22 12:53:46.382: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 64 changed to up
Router#
*Mar 22 12:53:46.415: ISDN BR1/0 Q931: TX -> CALL_PROC pd = 8 callref = 0xF3
Channel ID i = 0x89
*Mar 22 12:53:46.439: ISDN BR1/0 Q931: TX -> DISCONNECT pd = 8 callref = 0xF3
Cause i = 0x8081 - Unallocated/unassigned number
*Mar 22 12:53:46.527: ISDN BR1/0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x73
Cause i = 0x87E4 - Invalid information element contents
Router#
thanks for your helpYou have to either use a transfer pattern or a translation rule.
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/products_feature_guide_chapter09186a00801812db.html -
hi
i am facing data from problem from dso to cube
i am getting daat into dso
plant material doc_num itemno qty
p1 m1 1 1 10
p1 m1 1 2 20
dso i am uisng key fields
doc_no
item_no
doc_year
data fields
material
plant
qty
while loading data into cube
its showing only
p1 m1 1 2 20
item 1 is missing
there is no iten num filed in my target field?
ple let me know ur idea.Hi,
The problem is in your ODS/DSO.
In your ODS you have 'Doc_num' as key field.
For both Items 1 & 2, you have same key field ( Doc_Num) Value.
So, the first record will be over written by the second one. So from your ODS you will get only the latest record to the Cube.
If you want to send both doc_nums to cube, you need to bring doc_num to the data fields area of ODS.
Hope this helps.
Cheers
Praveen -
Hello,
I have unity connection 8.6 .2 and our corporate users need to access their voice mail when they are not in the office (from PSTN) so how i can achieve that.
I know only 2 steps please correct me if the below 2 steps are wrong and complete the rest of the steps
I will create a hunt pilot DN (DID) with unity connection answering ports.
call will reach to unity connection by direct routing rule configured for dialed in number (DID )
thanksDear's
you"ll are experts i may not understanding what actually you'll are trying to explain.Please bare with me to get success.
I will write in bullets my understanding please correct and also
when a pstn user dial a number 23232980
VG (MGCP) receives the calls and the call is send to CUCM to DN 980
In my case 980 is Hunt pilot the call will hit to Unity connection
By creating forwarding rule " sends call to" conversation sign in with equal operator & dialled in 980 routing rule conditions.
user will be prompted for the username and password.
Please write in Bullets for the below comment.
And, as Terry mentioned, you need to add appropriate translations to convert your DID to the Hunt Pilot number.
I didn't understood below paragraph.
An alternate option is to add 'Alternate extensions' for the user. In this case, apart from adding the alternate extensions, you do not have to do any other changes on Unity Connection. Callers can still dial the existing hunt pilot to reach unity connection. no need to create a new hunt pilot. just ensure you have appropriate translation patterns to convert your DID to the existing hunt pilot number.
Thanks -
I have set up my new iPad 2 on my computer (Windows 7), but experienced syncing problems from the start. It seems that although my iPad is regognized in iTunes as it appears there, it only gives met the options to set up as a new iPad or restore from the backup, no synching options. What do I do?
File>Devices>Transfer Purchases will transfer the itunes purchases to your ocmputer.
You should sync your ipod to your computer regularly. -
Communication problem from the vpn-anyconnect to easy-vpn-remote
Hi Team,
I have a communication problem from the vpn-anyconnect to easy-vpn-remote, I´ll explain better bellow and see the attached
topology:
1) VPN Tunnel between HQ to Branch Office - That´s OK
2) VPN Tunnel between Client AnyConnect to HQ - That´s OK
The idea is that the Client Anyconnect is to reach the LAN at Branch Office, but did not reach.
The communication is stablished just when I start a session (icmp and/or rdp) from Branch Office to the Client AnyConnect,
in this way, the communication is OK, but just during a few minutes.
Could you help me?
Bellow the IOS version and configurations
ASA5505 Version 8.4(7)23 (headquarters)
ASA5505 Version 8.4(7)23 (Branch)
**************** Configuration Easy VPN Server (HQ) ****************
crypto dynamic-map DYNAMIC-MAP 5 set ikev1 transform-set ESP-AES-256-SHA
crypto map outside-link-2_map 1 ipsec-isakmp dynamic DYNAMIC-MAP
crypto map outside-link-2_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside-link-2_map interface outside-link-2
access-list ACL_EZVPN standard permit 10.0.0.0 255.255.255.0
access-list ACL_EZVPN standard permit 192.168.1.0 255.255.255.0
access-list ACL_EZVPN standard permit 192.168.50.0 255.255.255.0
access-list ACL_EZVPN standard permit 10.10.0.0 255.255.255.0
group-policy EZVPN_GP internal
group-policy EZVPN_GP attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value ACL_EZVPN
nem enable
tunnel-group EZVPN_TG type remote-access
tunnel-group EZVPN_TG general-attributes
default-group-policy EZVPN_GP
tunnel-group EZVPN_TG ipsec-attributes
ikev1 pre-shared-key *****
object-group network Obj_VPN_anyconnect-local
network-object 192.168.1.0 255.255.255.0
network-object 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
network-object 192.168.50.0 255.255.255.0
object-group network NAT_EZVPN_Source
network-object 192.168.1.0 255.255.255.0
network-object 10.10.0.0 255.255.255.0
object-group network NAT_EZVPN_Destination
network-object 10.0.0.0 255.255.255.0
nat (inside,outside-link-2) source static Obj_VPN_anyconnect-local Obj_VPN_anyconnect-local destination static Obj-VPN-
anyconnect-remote Obj-VPN-anyconnect-remote no-proxy-arp route-lookup
nat (inside,outside-link-2) source static NAT_EZVPN_Source NAT_EZVPN_Source destination static NAT_EZVPN_Destination
NAT_EZVPN_Destination no-proxy-arp route-lookup
nat (outside-link-2,outside-link-2) source static Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote destination static
NAT_EZVPN_Destination NAT_EZVPN_Destination no-proxy-arp route-lookup
**************** Configuration VPN AnyConnect (HQ) ****************
webvpn
enable outside-link-2
default-idle-timeout 60
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles Remote_Connection_for_TS_Users disk0:/remote_connection_for_ts_users.xml
anyconnect enable
tunnel-group-list enable
access-list split-tunnel standard permit 192.168.1.0 255.255.255.0
access-list split-tunnel standard permit 192.168.15.0 255.255.255.0
access-list split-tunnel standard permit 10.0.0.0 255.255.255.0
group-policy clientgroup internal
group-policy clientgroup attributes
wins-server none
dns-server value 192.168.1.41
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split-tunnel
default-domain value ipconnection.com.br
webvpn
anyconnect keep-installer installed
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect profiles value Remote_Connection_for_TS_Users type user
anyconnect ask none default anyconnect
tunnel-group sslgroup type remote-access
tunnel-group sslgroup general-attributes
address-pool vpnpool
authentication-server-group DC03
default-group-policy clientgroup
tunnel-group sslgroup webvpn-attributes
group-alias IPConnection-vpn-anyconnect enable
object-group network Obj_VPN_anyconnect-local
network-object 192.168.1.0 255.255.255.0
network-object 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
network-object 192.168.50.0 255.255.255.0
object-group network NAT_EZVPN_Source
network-object 192.168.1.0 255.255.255.0
network-object 10.10.0.0 255.255.255.0
object-group network NAT_EZVPN_Destination
network-object 10.0.0.0 255.255.255.0
nat (inside,outside-link-2) source static Obj_VPN_anyconnect-local Obj_VPN_anyconnect-local destination static Obj-VPN-
anyconnect-remote Obj-VPN-anyconnect-remote no-proxy-arp route-lookup
nat (inside,outside-link-2) source static NAT_EZVPN_Source NAT_EZVPN_Source destination static NAT_EZVPN_Destination
NAT_EZVPN_Destination no-proxy-arp route-lookup
nat (outside-link-2,outside-link-2) source static Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote destination static
NAT_EZVPN_Destination NAT_EZVPN_Destination no-proxy-arp route-lookupHi,
the communication works when you send traffic from easyvpn branch side because it froms the IPSEC SA for local subnet and anyconnect HQ pool. The SA will only form when branch initiates the connection as this is dynamic peer connection to HQ ASA.
when there no SA between branch and HQ for this traffic, HQ ASA has no clue about where to send the traffic from anyconnect to branch network.
I hope it explains the cause.
Regards,
Abaji. -
User provisioning problem from OIM 10g to Siebel CRM
Hi Team,
I am facing User provisioning problem from OIM 10g to Siebel CRM.Please find the log details.
Running Get Attribute Mapping
Running Siebel Create User
<com.siebel.common.common.CSSException>
<Error><ErrorCode>8716601</ErrorCode> <ErrMsg>Socket had incorrect word size: 0.(SBL-JCA-00313)</ErrMsg></Error>
</com.siebel.common.common.CSSException>
at com.siebel.om.conmgr.Connection.readPacket(Connection.java:550)
at com.siebel.om.conmgr.Connection.run(Connection.java:286)
at java.lang.Thread.run(Thread.java:619)
[CMGR FATAL] Error: <com.siebel.common.common.CSSException>
<Error><ErrorCode>8716601</ErrorCode> <ErrMsg>Socket had incorrect word size: 0.(SBL-JCA-00313)</ErrMsg></Error>
</com.siebel.common.common.CSSException> connection:1
<com.siebel.common.common.CSSException>
<Error><ErrorCode>8716601</ErrorCode> <ErrMsg>Socket had incorrect word size: 0.(SBL-JCA-00313)</ErrMsg></Error>
</com.siebel.common.common.CSSException>
at com.siebel.om.conmgr.Connection.readPacket(Connection.java:550)
at com.siebel.om.conmgr.Connection.run(Connection.java:286)
at java.lang.Thread.run(Thread.java:619)
[CMGR FATAL] Error: <com.siebel.common.common.CSSException>
<Error><ErrorCode>8716601</ErrorCode> <ErrMsg>Socket had incorrect word size: 0.(SBL-JCA-00313)</ErrMsg></Error>
</com.siebel.common.common.CSSException> connection:1ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],com.thortech.xl.integration.siebel.utils.SiebelConnection : createSiebelConnection() : Siebel Connection Exception:Could not open a session in 4 attempts. {1}(SBL-JCA-00200)
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],com.thortech.xl.integration.siebel.proxy.SiebelProxyEmployeeProvisionManager : createSiebelConnection() : BaseException: Siebel Connection JDB Exception: Could not open a session in 4 attempts. {1}(SBL-JCA-00200)
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],com.thortech.xl.integration.siebel.provision.SiebelUtilEmployeeProvisionManager : createEmployee() : BaseException: Siebel Connection JDB Exception: Could not open a session in 4 attempts. {1}(SBL-JCA-00200)
ERROR,22 Aug 2013 12:58:27,689,[XL_INTG.SIEBEL],====================================================
Regards,
Ravi.Hi
I facing the same error message as yours, using OIM 11g R2
Are you able solve it ?
Please share
Many Thanks !!! -
Mapping problem:from E1EDK14-ORGID to PORDCR102-PUR_GROUP
Mapping problem:from E1EDK14-ORGID to PORDCR102-PUR_GROUP
E1EDK14 occurs 4 times in the source sys:
1 E1EDK14-QUALF = '014'
E1EDK14-ORGID = 'YP01' <= purchase organization
2 E1EDK14-QUALF = '009'
E1EDK14-ORGID = '001' <= purchase group
3 E1EDK14-QUALF = '013'
E1EDK14-ORGID = 'NB' <= document type
4 E1EDK14-QUALF = '011'
E1EDK14-ORGID = 'C999' <= company code
I always want to copy "E1EDK14-ORGID = '001'" to PORDCR102-PUR_GROUP.
I have a solution which works but not perfect:
E1EDK14-ORGID=>copyvalue[1]=>PORDCR102-PUR_GROUP
I want to have the perfect mapping as follow:
IF E1EDK14-QUALF = '009'.
E1EDK14-ORGID = '001' => PORDCR102-PUR_GROUP
ENDIF.
I did it in the data flow editor as follow:
/PORDCR102/IDOC/E1PORDCR1/E1BPMEPOHEADER/PUR_GROUP=
ifWithoutElse([keepss=false]stringEquals
(removeContexts(/ORDERS05/IDOC/E1EDK14/QUALF=),
const([value=009])), /ORDERS05/IDOC/E1EDK14/ORGID=)
But the result in the target sys is always 'YP0'(The first E1EDK14-ORGID)
How to solve this problem?
Thanks
ming yuHi,
Try like this.
E1EDK14-QUALF --------
Constant(009) ---------------- EqualsS ---------------
And(Boolean Function) ------ IfWithoutElse -- PORDCR102-PUR_GROUP
E1EDK14-ORGID ------- E1EDK14-ORGID ----------------
Constant(001) -------------- EqualsS ------------------
Regards,
P.Venkat -
Aperture Video Import Problem - from Lumix GH4: Imported clips have their dates changed to the import date. The files show up on the hard drive with import date not created date, but many of these same files are not showing up in Aperture. Sometimes the clips actually show up with the current import but take on the video information from a previously imported file.
It was suggested I move this question to IPhoto or IMovie which I did.
Well moving to a different discussion group did not provide an answer to this question either. But what I finally did was import one batch of photos and videos into IPhoto for a given day at a time. Working with these I could change the date and times in order to get them in the original sequench taken. Then I would create an album with that batch. These would all be on the same day (IMove was closed for this phase). Then I would open IMovie, generate the thumbnails for that album, and select the album I had created. This was necessary because the importing process in IPhoto was using incorrect dates for my video so it was a real struggle finding them in IMove until I developed this approach.
I believe that this whole process was so screwy because I was importing from an external hard drive not a camera. I had these photos on a PC and did not have the original cameras to use to import directly which I am fairly sure would have made this easier! -
Whenever I try to download or redox load an app, a sign says I need to sign in. I do, but it then says I have a billing problem from an earlier purchase and I don't have money on the card so I can't put anything even though I tried. How can I get rid of the card on my ipod??
Sounds like you have an outstanding balance. You have to pay that of before you can make purchases, even free ones. Add a valid payment method to your account
Why can’t I select None when I edit my payment information?
If you want to contact iTunes
Contact iTunes -
Hi,
When I run my report, its perfectly working fine with all the data, subtotals, grand totals etc.
But when I print the ALV by clicking the PRINT Button on the Standard tool bar, My first subtotals are printing correctly. From second, its printing ZEROES and my grand totals are printing double the number as I see on the output.
This is strange and am not able to understand why I get those errors.
ANy pointers please.
Thanks,
Kiran
Edited by: kiran dasari on Sep 9, 2009 1:04 AMHi Roger,
I am using Function Module "REUSE_ALV_HIERSEQ_LIST_DISPLAY"
I am displaying a hierarchical ALV with subtotals, page-breaks & grand totals.
The strange thing is that my first SUBtotal gets printed properly. Its the problem from the second subtotal onwards.
Finally, the grand totals also a problem(Doubling when i print first time and triplling,if i print 2nd time ...and so on...)
ANy more clues please.
Thanks,
Kiran D -
Video transfer problem from pc to ipad A1219
video transfer problem from pc to ipad A1219
ArinC
You have posted your issue in Using Apple Support Communities whose topic is 'How to use this forum software's interface, features and/or how to find what you wish'. It is a relatively low traffic and inappropriate forum for your problem. I will ask our Hosts to move it to " Using iPad " where it may get a more rapid response from your fellow users.
best luck
ÇÇÇ -
I have a problem, from system test says: Error 4mem/61/400000000:0x8444fb98, I know how you can solve.
If you have Apple Care for that computer, give them a call: Apple's Customer Support - in the US, (800) 767-2775
If you're not sure how to handle the situation, consider walking your MB into the nearest Apple Store and asking someone there to take a look, etc.
Good luck in any case. -
Boss has a 3G having syncing problems from Iphone calendar to laptop caledndar.
We run Windows 7 here at work and when she goes to sync her iphone calendar to her laptop calendar some of the information is not transferring over. Yesterday we synced and everything was correct on both calendars but when we went back in today there were missing appts on the laptop calendar that were synced yesterday.
-
Changing FROM header during Forwarding from PSTN to PSTN
Hi,
Is there a possibility to change the FROM header in INVITE message:
1. calling from PSTN network to lync user
2. user got call forwarding to PSTN number set
that the FROM header got user's number?
Lync is 2013 with newest update.You can work with the caller id a bit in the trunk rules, but likely you'll want an SBC to do anything more sophisticated.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications
This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.
Maybe you are looking for
-
Basic functions and functionality missing from Safari 4.0
Just trying to move to Safari from Firefox. The Develop tools cinched the move (hidden by default! Huh?). After all the years, I cannot believe Apple still haven't fixed some basic requirements of a web browser. 1. Cannot find anything similar to Liv
-
I have some PHP pages I have programmed that do database inserts and updates. I am using Dreamweaver and an extention package called InterAkt MXKollection to enhance some features on the web page. In particular some fields on the page use what is cal
-
Pictures are no longer loading in Safari, any clues?
Recently I'm finding that many pages on Safari are not loading properly and/or pictures do not load. Perhaps I need to update something, but I am not sure what or how. Does anyone have any suggestions? Thanks!
-
hi how to run report in background and store it in cache thanks in advance krish
-
How to analysys account dimension in planning to write view to load metadat
hi, i need to analysys some dimensions in plannning application,coud u please hepl me to send any documents to my gmail [email protected] also i need to write view to load meta data to planning through HAL. Thanks Subbu.