Calling ID to PSTN with CME vs Ericsson MD110 and E1
Hi all,
We are having problems with calling party identification in the following scenario: some IP phones managed by a 2800 CME router. This is connected to an Ericsson MD110 PBX through a E1 with QSIG signalling. There is absolutely no problem when identifying both called and calling parties in both directions ingoing and outgoing from the router to the PBX private extensions. It also works fine when calling from the PSTN to direct public numbers redirected from the PBX to the IP phones extensions. However, when calling from these particular extensions, we want the calling party to identify with its particular public number, but instead it shows at the PSTN end with the main number of the ISDN jump group.
Anyone has experienced the same?
Thanks and regards,
Jose Soriano
Hi,
I'll try to be more clear. As I said, we have a CCME connected to an Ericsson MD100 via an E1 Qsig link. Then the MD110 goes to the PSTN also with an E1. The customer has several ISDN public numbers associated with that E1, one of them is the main ISDN group number, with which the originator of all the outgoig calls from the private numbers to the PSTN identify, except for some private extensions associated with one of the other direct public numbers: these can be reached directly through these numbers and also are identified with those numbers when calling to the PSTN.
Let's say we have 30 public numbers, from 555100 to 555129, beig 555100 the main number. Ext 101 is associated to public number 555101, and 102 with 555102. In the situation with no CCME, the call flow is as follows.
Private Ext. 101 (dials a public number) --> PBX EMD110 --> PSTN (displays 555101 as the caller ID)
PSTN dials 555101 --> PBX EMD100 --> Private Ext. 101
Now, let's include the CCME system. Let's say Ext. 102 is an IP Phone extension correctly routed between CCME and MD110. Also, ext. 102 should be identified to the PSTN as 555102.
Case A)
IP Phone 102 (dials a public number) --> CCME --> PBX EMD110 --> PSTN (displays 555100, and NOT 555102 as the caller ID)
Case B)
PSTN dials 555102 --> PBX EMD100 --> CCME --> IP Phone 102
The PRIVATE flow between CCME and MD110 is fine:
IP Phone 102 dials 101 --> CCME --> PBX EMD110 --> Private Ext 101 displays 102 as the CLID
Private Ext 101 dials 102--> PBX EMD100 --> CCME --> IP Phone 102, with 101 as the CLID
So, the problem is in what I called CASE A), calls do not idetify with the especific public number, but with the main group number when they are routed through the PSTN.
Regards,
Jose Soriano
Similar Messages
-
Hi,
unable to set up call forward to PSTN.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
I have tried activating the Call forward via the phone or manually via the config, but when I attempt a call to IP Communicator from PSTN or via extn I am not seeing re-INVITE which should be generated for the forwarded call. Am i missing something?
PSTN / IP phone ------> Calling extn on CME (which is call forwarded to another PSTN number)
config below:
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server expires max 250 min 200
asserted-id pai
localhost dns:XXXXX
outbound-proxy dns:XXXXX
dial-peer voice 100 voip
description ** Incoming call from SIP trunk **
session protocol sipv2
session target sip-server
incoming called-number .
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 101 voip
description ** Outgoinging call to SIP trunk **
translation-profile outgoing SIPOUT
destination-pattern 1T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
voice-class sip profiles 101
dtmf-relay rtp-nte
no vad
dial-peer voice 102 voip
description ** Outgoinging call to SIP trunk **
destination-pattern 0[2-9].T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
telephony-service
max-ephones 4
max-dn 12
ip source-address 192.168.100.2 port 2000
calling-number initiator
timeouts interdigit 5
load 7960-7940 P00308010200
date-format dd-mm-yy
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1 dual-line
number 4961 secondary 99474961 no-reg both
label 4961
name 4961
call-forward all 021605547/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Does a direct call (without forwarding) work through this dial-peer? YES
The session target of dial-peer 101 is the "sip-server". In wich way is configured? Is it an IP address or a name? FQDN
Can you ping it from the CME? YES
The CME can resolve the name via DNS? Resolved on the CME Can you post the sip-ua config?
sip-ua
credentials number 99474960 username 99474960 password 7 XXXXXXXXX realm as-test.xys.net
authentication username 99474960 password 7 XXXXXXX
calling-info pstn-to-sip asserted-id number set 99474960
no remote-party-id
disable-early-media 180
retry invite 2
retry register 3
timers connect 100
registrar dns:as-test.xys.net expires 60 sip-server dns:as-test.xys.net
host-registrar -
Ericsson MD110 and Cisco routers ISDN PRI Q-Sig
Anybody has experience with MD110 and Cisco integration using ISDN PRI Q-Sig... Have problems with "idle-busy" channels on MD110. It looks like PBX does not recognize disconnect signal coming from the router.
Tks
BraniMC,
Ericsson MD110, BC12 SP7
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
175 0110017500000010 5 3110000000 0 30 128 00080812 511110120031 111111
157 0110017500000010 5 3110000000 0 30 128 00080812 511110120031 111111
END
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
175 SL60 H'00000310 H'15420000 H'46300000 NO
157 SL60 H'00000310 H'15420000 H'46300000 NO
END
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
175 175 1606100000000250006000000 0 1 0
157 1 2606100000000250006000000 0 1 0
END
Cisco IOS 12.3-3 (c2600-jsx-mz.123-3.bin)
Cisco config attached.....
Our serial links are satellite based so min delay is about 500ms
Tks
Brani -
How calling a java WS with WSS4J from PL/SQL and UTL_DBWS?
Hi to everybody,
I have a problem, I have a web service implemented with wss4j and i need to call it from a pl/sql storeprocedure using utl_dbws.
I saw many examples in the web but i didn't find one suitable for this situation.At this time a think that is not possible to use wss4j and utl_dbws, so I decided to use java store function.
Now i made a jar file that contain the classes with the beans and the stub for the call.
I loaded every jar with this command
loadjava -thin -userxxxx/[email protected]:xx:xxxx -synonym -verbose -grant public jarfilename.jar
When i compile them i have a lot of error for dependeces there is a way to do it? -
4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN
Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
I can receive calls from PSTN.
Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
I cannot receive directly calls form PSTN.
Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091\(..\)/ /\1/
rule 2 /^2929091\(.\)/ /\1/
rule 3 /^02929091\(..\)/ /\1/
rule 4 /^02929091\(.\)/ /\1/
voice translation-rule 2
rule 2 /\(.*\)/ /02929091\1/
voice translation-rule 10
rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn
rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
! Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
! FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio. -
Blackberry registeration with CME
hi all,
I want to know whether one can install the client on blackberry phone same as nokia e71 and register the blackberry phone with cme via wifi. Can somebody provide the link for the documentation
Regards
NarehIt seems BlackBerry launched complete product - the BlackBerry® Mobile Voice System that can be integrated with CME:
http://na.blackberry.com/eng/services/business/blackberry_mvs/
Here is Configuration Guide:
http://docs.blackberry.com/en/admin/deliverables/20062/BlackBerry_Mobile_Voice_System-Configuration_Guide--1079341-0901073810-001-5.0.1-US.pdf
What I have noticed from document is that "the BlackBerry® Mobile Voice System integrates your organization's PBX phone system with the BlackBerry® Enterprise Server to extend desk phone features to BlackBerry devices". In other words you will need BlackBerry® Enterprise Server working as well for the system to function.
So I guess to install all it if you have only couple of BlackBerry phones is senseless.
I'm curious if it would be possible to use without BlackBerry® Enterprise Server having just simple client on the phone like Nokia Call Connect, for instance with Nokia E-series phones. -
7921 to 7921 Calls Have no audio with UC540 and AP541n
We have a new deployment where we have 5 total 7921G wifi phones connected via 2 AP541n access points, one connected to a ESW520p switch and then to the UC540 and the other connected directly to the UC540. The wifi phones are intermittently giving no audio when calling each other, however, calls to the PSTN consistently do have 2 way audio. Is this a security issue perhaps? We are running the latest CCA software pack as this is a brand new deployment, also the AP's were upgraded to the latest firmware. HELP.
I have also tested this scenario in the past and I found that phones associated to the same ap
did seem to have a higher incidence of the one-way audio condition but not every time. We have 3 4404 controllers and I did note that every time I a complaint the phones involved were on the same controller. I could not reproduce the problem EVER if the phones were associated to aps on different controllers, TAC assured me that this was unlikely related to the issue but I have my doubts. Since upgrading the phones to the latest firmware 1
.3.4SR1 initially I was still getting complaints of the condition occuring so I decided to reboot the POE switches involved with the problem areas since they had in some cases been up for 2+ years, this was just a last ditch effort but for whatever reason that seems to have cleared up the issue. I have not had the issue reoccur in the past 2 weeks since rebooting those switches, I also believe that some of the phones in question had not yet received the update and because of this I was getting false reports of upgraded phones still having the issue. I found two seperate cases where one of the phones in question still had 1.3.3, after forcing the upgrade they were fine. So first thing I would do is make sure the phones have 1.3.4SR1, then I would check to see how long the switches connected to your AP's have been up and also perhaps the IOS version, if they are Cisco switches it may not hurt to contact TAC and see if they can recommend an IOS that would be a good candidate. Another thing to make sure is that your QoS settings on all the switches involved are set correctly. We had tons of problems initially when we first started using the phones on the wireless network. We thought our QoS was set correctly but what we found was there was some IOS bugs on some of the switches downstream that required special switchport commands to "fix". Most dealt with the qos trust dscp command, some switches had to have the dscp tag and some had to have the cos tag, very strange and it took several CCIE's several days to come up with the final solution after many wireshark traces to make sure the QoS tags were making it all the way through.
Watch, now that I am writing you that my problems seem to be fixed, I am sure Murphy will raise his ugly head and ruin my Friday -
Does Cisco CP-8831 work with CME
Hello
Does Cisco CP-8831 phone work with the Call Manager Express
Thanks
MohamedAs of now no.
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps12965/data_sheet_c78-726887.html
"Supported on Cisco Unified Communications Manager and Business Edition systems"
There is a defect open that the 8831 datasheet is incorrect with CME 10.0 support for the 8831 (https://tools.cisco.com/bugsearch/bug/CSCui95307/). -
Test call of TP ended with return 0212
while releasing a transport request, getting the following error message-
test call of TP ended with return 0212
your transport request cannot be exported , since all the requirements are not fulfilled
calling transport control (tp) program "TP EXE CHK DEVK908291 pf=usr/sap/trans/bin/tp_domain_PRD.pfl -Dtransdir=usr/sap/tr"
which checks the export requirement , returned the following information
returned code from tp :0212
further processing is terminated
Please help if anyone has any clue
Regards
Al MamunHi Eric,
Thanks for your reply,
I have checked the configuration, looks ok. The path is ok, I missed the / before usr while typing this message.
one thing I checked that there is no cofile or datafile corresponding to that transport. Same thing is happening while releasing other transports.
Is it mount problem?
Al Mamun -
Caller ID not working with Nokia 6600?
I have a T-Mobile (US) Nokia 6600, and I can't seem to get address book to display incoming SMS or the caller ID of incoming calls. I've successfully paired the phone via bluetooth, and I can make address book dial the phone and send an sms. I can sync via iSync, use my phone as a modem, etc. etc.
But regardless of what settings I tweak, I can't seem to get Address Book to show a bezel of any kind on incoming calls - not even an 'Unknown Caller' message! Am I missing something obvious? Third party apps like BluePhoneElite work just fine, so I'm pretty sure it's something wrong with Address Book...
15" Aluminum Powerbook 1.5 GHz Mac OS X (10.4.5)
mdcdsc wrote:
My caller ID does not work with the new ap either. I don't like the new ap at all. The old one was beautiful. Now my email is very hard to see, so much that I will just use the Apple email that comes with my IPOD. The caller ID was my favorite thing with the old ap. and now it doesn't work. I have followed the instructions and turned everything on, but it just does not work.
The Caller ID issue was due to an outage. It should be resolved anytime soon. Can yu log out and log back in. Go to app settings and in notifications and turn CAller ID off and on.
On email - what do you mean 'email is very hard to see' ? I would like to pass on this feedback to the team. -
How do I make a phone call from my mac with yosemite?
How do I make a phone call from my MacBook Pro on the Yosemite operating system?
The following quotation is from Connect your iPhone, iPad, iPod touch, and Mac using Continuity
There is more information in the link, including supported hardware and that you must have Settings > FaceTime > iPhone Cellular Calls set to on on the iPhone.
Phone calls
With Continuity, you can make and receive cellular phone calls from your iPad, iPod touch, or Mac when your iPhone is on the same Wi-Fi network.
To make and receive phone calls, here's what you need:
Sign in to the same iCloud account on all your devices, including your Mac.
Your iPhone and your iPad or iPod touch need to use iOS 8 or later. Your Mac needs to use OS X Yosemite.
All devices must be on the same Wi-Fi network.
All devices must be signed in to FaceTime using the same iCloud account. This means any device that shares your Apple ID will get your phone calls. Look below for instructions on how to turn off iPhone cellular calls.
Wi-Fi Calling needs to be off. Go to Settings > Phone. If you see Wi-Fi Calling, turn it off.
Make a call
To make a phone call on your Mac, iPad or iPod touch tap or click a phone number in Contacts, Calendar, or Safari. -
How to call a dialog program with return value in another dialog program
Dear All,
How can I call a dialog program with return value from another dialog program?
Regards,
Alok.Hi Alok,
You can you SET/GET parameters to do this.
This is some information about this.
To fill the input fields of a called transaction with data from the calling program, you can use the SPA/GPA technique. SPA/GPA parameters are values that the system stores in the global, user-specific SAP memory. SAP memory allows you to pass values between programs. A user can access the values stored in the SAP memory during one terminal session for all parallel sessions. Each SPA/GPA parameter is identified by a 20-character code. You can maintain them in the Repository Browser in the ABAP Workbench. The values in SPA/GPA parameters are user-specific.
ABAP programs can access the parameters using the SET PARAMETER and GET PARAMETERstatements.
To fill one, use:
SET PARAMETER ID pid FIELD f.
This statement saves the contents of field f under the ID pid in the SAP memory. The ID pid can be up to 20 characters long. If there was already a value stored under pid, this statement overwrites it. If you double-click pid in the ABAP Editor, parameters that do not exist can be created as a Repository object.
To read an SPA/GPA parameter, use:
GET PARAMETER ID pid FIELD f.
This statement places the value stored under the pid ID into the variable f. If the system does not find any value for pid in the SAP memory, sy-subrc is set to 4. Otherwise, it sets the value to 0.
Thanks,
SriRatna -
I have a IPhone 5 and Iphone 5s, each phone is activited with a different service provider. Both are set up with the same account ID and running IOS 8.0.2. When the phones are connected to the same Wifi at home, both phones will ring when someone call in to one of the phone. Hence you do not know exactly which line the caller called. If you answered using the wrong phone, then anyone calling the other number will not get through. Anyway to solve this problem?
Hey David Koh TP,
Thanks for the question. It sounds like your devices are set up to use continuity together. Specifically, it sounds like you are signed into the same Apple ID in FaceTime, and have iPhone Cellular Calls enabled. To resolve your issue, simply disable this setting:
Connect your iPhone, iPad, and iPod touch using Continuity
http://support.apple.com/kb/HT6337
Turn off iPhone cellular calls
To turn off iPhone Cellular Calls on a device, go to Settings > FaceTime and turn off iPhone Cellular Calls.
Thanks,
Matt M. -
My project requires me to convert a C++ program to a DLL and having it called by LabVIEW. Due to the complexity of this C++ program (converted from fortran using f2c -C++ option), it cannot be compiled without using /clr option. I did build the application standalone (/clr), and it functioned fine. When I build it into DLL using VS2005, I was forced to use No Entry point option and without using DllMain in the C++ code. Eventually the DLL was built without error. But after I call it from LabVIEW, I was not getting calculated results as expected. I added a testing function to the C++ code of the DLL and just try to modify a parameter, it will not, but only return the input numbers. I was passing data by pointer and not by value, so I expect this parameter output be modified. I suspect that the DLL didnt get executed at all as it has no entry point specified.
Am I on the right track to approach this task, or I am heading to totally wrong direction here? I believe due to the fact that my C++ was from f2c and use vsf2c.lib and so on, the code is managed code, so that a regular DLL cannot be built from it with an entry point. How can LabVIEW call such a DLL? Am I right on that? I really need your advice here for a right approach to this problem and possible implementation "watch outs"...Thanks!
BryanHi...Finally I was able to compile my code with an entry point defined and without using /clr. I can also call this DLL from LV and got back a variable from a little test function added to the DLL. But the function that was used for my main application in the DLL crashed LV and I got a pop up box from Microsoft Visual C++ Runtime Library: Runtime Error! "This application has requested the Runtime to terminate it in an unusual way, please contact the application's support team for more information". In Visual Studio I also got the following message: (I eliminated most of the "No symbols loaded" messages that are not errors but just info.) I would apprciate if someone can take to look with your more "experienced eyes", many thanks! Bryan.
'LabVIEW.exe': Loaded 'C:\WINDOWS\WinSxS\x86_Microsoft.Windows.Common-Controls_6595b64144ccf1df_6.0.2600.2180_x-ww_a84f1ff9\comctl32.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\xpsp2res.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\Shared\nicont.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\Shared\NICONTDT.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\nitaglv.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\lkbrow.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\lkrealt.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\lvdaq.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\lvdesktop.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\lvfp.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\mfc71.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\MFC71ENU.DLL', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\vi.lib\FieldPoint\SubVIs\FPLVMgr.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\lvfprt.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\LvProjectProxy.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\LvRealTimeCoreProvider.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\MVEProvider.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\QtCore4.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\QtXml4.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\QtGui4.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\mxLvProvider.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\nimxlcpp.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\nimxlc.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\Providers\variable.mxx', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\Framework\lvMax.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\MAX\UI Providers\FieldPoint71.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\MathScriptParser.dll', Binary was not built with debug information.
'LabVIEW.exe': Loaded 'Z:\bli\development\projects\galfitDLL\Debug\galfitDLL.dll', Symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\WinSxS\x86_Microsoft.VC80.CRT_1fc8b3b9a1e18e3b_8.0.50727.762_x-ww_6b128700\msvcr80.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\Program Files\National Instruments\LabVIEW 8.5\resource\mesa.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\mscms.dll', No symbols loaded.
'LabVIEW.exe': Loaded 'C:\WINDOWS\system32\icm32.dll', No symbols loaded.
The thread 'Win32 Thread' (0xf94) has exited with code 0 (0x0).
The thread 'Win32 Thread' (0x90c) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xfd0) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x284) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xdac) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xa98) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x528) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x614) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xa5c) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xebc) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x5cc) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x700) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xcf0) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xc7c) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x4c8) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0xa4) has exited with code 3 (0x3).
The thread 'Win32 Thread' (0x52c) has exited with code 3 (0x3).
The program '[804] LabVIEW.exe: Native' has exited with code 3 (0x3). -
How to call a AM method with parameters from Managed Bean?
Hi Everyone,
I have a situation where I need to call AM method (setDefaultSubInv) from Managed bean, under Value change Listner method. Here is what I am doing, I have added AM method on to the page bindings, then in bean calling this
Class[] paramTypes = { };
Object[] params = { } ;
invokeEL("#{bindings.setDefaultSubInv.execute}", paramTypes, params);
This works and able to call this method if there are no parameters. Say I have to pass a parameter to AM method setDefaultSubInv(String a), i tried calling this from the bean but throws an error
String aVal = "test";
Class[] paramTypes = {String.class };
Object[] params = {aVal } ;
invokeEL("#{bindings.setDefaultSubInv.execute}", paramTypes, params);
I am not sure this is the right way to call the method with parameters. Can anyone tell how to call a AM method with parameters from Manage bean
Thanks,
San.Simply do the following
1- Make your Method in Client Interface.
2- Add it to Page Def.
3- Customize your Script Like the below one to Achieve your goal.
BindingContainer bindings = getBindings();
OperationBinding operationBinding = bindings.getOperationBinding("GetUserRoles");
operationBinding.getParamsMap().put("username", "oracle");
operationBinding.getParamsMap().put("role", "F1211");
operationBinding.getParamsMap().put("Connection", "JDBC");
Object result = operationBinding.execute();
if (!operationBinding.getErrors().isEmpty()) {
return null;
return null;
i hope it help you
thanks
Maybe you are looking for
-
ITUNES WON'T OPEN!!! PLEASE HELP ME I'M GOING INSANE!!
I have a dell computer.. I have Windows XP I got itunes wiht a new ipod mini in the fall. everything was going great, I even upgraded to the new itunes and everything was fine until about a month ago when it just quit on me. when I try to open itunes
-
How do I access my itunes on a new computer without access to the old?
My old computer is dead and gone and I do not own an iphone, but have gotten a new computer. How do I access my itunes and all the content I have been putting on it for so long now? My new computer is an acer; I do not own any apple products yet (p
-
Customer and vendor line item report FBL5N/FBL1N
Dear all, Could you please let me know, whether there is any way that we can get cost center ans wbs element in customer and vendor line item report FBL1N/FBL5N. REgards, Suresh Patipati.
-
How to fix mms size restriction
some of my incoming text messages say "media content was not included due to a picture resolution or message size restriction", how can i fix this?
-
Hi Experts, I cannot see UWL for Employee Self-Service role where as under Manager Self-Service I can see it. Do we have to add the page manually or it will be done from backend. ESS/MSS Version is 1.41. Please throw some light on this. Thanks, Murth