Calling on all clear enclosure display owners; especially the 23" HD displ

Folks,
Am I over reacting or is there something wrong with my HD display? I recently purchased a 23" HD display (clear enclosure) and ever since I've had it, I've noticed a "flickering". It is most pronouced when I have the brightness setting to it's lowest. At its worst, you can really tell. You don't need a sensitive eye. It's really annoying. I currently have it at about 50% brightness level and my eyes can sense a slight, like 10% flickering. 100% being, no flickering at all. This is also inconsistent. At times, most of the flickering goes away, and when I think all is well, it comes back with a vengeance. I'd like to get a consensus on this from owners of the cinema display, preferably the 23" HD prev. generation to current, but all feedback would be appreciated. Did I get a defective screen? A lemon or is this typical of this display? Thanks. I need to make a decision as to what I'm going to do with this monitor ASAP. No later than today 1.23.06. As if it gets too bad, I might just have to contact the seller and see if I can arrange a return. Thanks!!!

Yes I have a 30" Cinema Display which flickers especially in the dark black areas, I'm yet to find any solution to fix it. This seems to be a manufacturers problem that is yet to be resolved. I wish Apple would take this problem more seriously and try to solve this flickering.
Your not over reacting it a major problem.

Similar Messages

Clear enclosure 23" cinema display with DVi connector?

Hi all,
I went to a local Mac store (Not Apple) where I was shown a supposedly 23" HD cinema display (clear enclosure) with a DVI CONNECTOR directly built in. I was under the impression that all clear enclosure versions natively came with the ADC connector and that if DVI was warranted, a converted was necessary. To my surprise, Apple apparently made two clear enclosure versions, both ADC and DVI. I've verified under the spec. area of this site. But, there were no 23" clear enclosure with DVI, except of course, the current 23 version which is the aluminum. So, was the more likely scenario that this rep. had shown me a 22 with DVI or is there really a 23 version with DVI. I was convinced at the time myself that it was a 23 clear enclosure version with a DVI connector. I saw with my own eyes that this display did not have a converter connected and it looked like the 23 as opposed to a 22. The 22 & 23 looks so similar and can be mistaken for each other. One of the ways of identifying readily is that the 22 has the power/brightness controls near the bottom right of the casing. Could someone confirm either way. Thanks!

Hi-
I agree that the rep probably showed you a 22" DVI model. See page 8 of the 22" Cinema Display Manual for the cabling of the display.
You will see the DVI version of the Cinema Display listed in this article. The article was put out prior to the Aluminum housed ACD release.

My Yahoo Mail in Firefox now won't give me the name list in the To/CcBcc fields ? Has been fine. Firefox is the latest version and history etc all cleared.e

My Yahoo Mail in Firefox now won't give me the name list in the To/CcBcc fields which has been working fine.
Firefox is the latest version and history etc all cleared.
I have done the syncing again and restarted.. That e-mail address field still not accessed.
The Yahoo Mail works fine as before if using Internet Explorer...
Help please...
............................................

My Firefox was always been in "Never remember History" .... and I have just cleared All History again.. and it still doesn't work..

Automatically display number when the mouse attach approach node for chart ?

Hi all,
can automatically display number when the mouse attach approach node for chart ?
For detail ,see attach file
Thanks in advance !
Attachments:
chart display.JPG ‏70 KB

Charts don't have cursors and they also don't have the "plot images" options, so your tools are limited.
Of course you can simulate a chart using a graph by keeping your own history and display it on a graph. Use cursor move events to trigger the calculation of the distances from the new cursor position to all points on the graph and pick the one with the shortest distance to the cursor. Now you can get the annotation tools to label the point, or get its x and y value and write the info using picture tools with the "plot images" property.
LabVIEW Champion . Do more with less code and in less time .

I updated my Iphone4S this week to the newest IOS 7.1 and now everyone who calls me says the calls are not clear, muffled. Is there something I can do to clear this? 4 people in 4 different states that called me all said the same thing.

I updated my Iphone4S this week to the newest IOS 7.1 and now everyone who calls me says the calls are not clear, muffled. Is there something I can do to clear this? 4 people in 4 different states that called me all said the same thing.

Settings > General > Reset > Reset Network Settings
Contact the carrier to troubleshoot.

Calling all Apple and Mac owners! HP Expert Day - Aug 15th, '12

Thank you for coming to Expert Day – the event has now concluded.
**To find out about future HP Expert Day events, check out this page**
On behalf of the Experts, I would like to thank you for coming to the Forum to connect with us. We hope you will return to the boards to share your experiences, both good and bad.
We will be holding more of these Expert Days on different topics in the months to come. We hope to see you then!
If you still have questions to ask, feel free to post them on the Forum – we always have Experts on the HP Support Forum to help you out.
On August 15, 2012, the Consumer Support Forum will host an Expert Day dedicated to answering your questions about Mac OS X, iOS and AirPrint™ for HP products and peripherals. With the introduction of Apple’s new OS X Mountain Lion, we’re ready to help with set-up, installation and general HP compatibility questions all day long.
Join Mac experts on the forum between 7:00am and 5:00pm PDT to learn all about Mac compatibility with HP printing and peripheral solutions. No question is off-limits and the event is free for both in-and out-of warranty products.
How to Participate
To participate in Mac Expert Day, simply log into the Consumer Support forum and head to the Mac Printing & Scanning Board to post a question. Select the “Email me when someone replies” option to receive a notification when and Expert addresses your question.
If you are not already a forum member, simple click “Register Now” on the forum home page (www.hp.com/supportforum) and follow the quick registration process.
Remember to say "Thanks" by clicking the Kudos Star in the post that helped you. You can also mark the post that solves your problem as "Accepted Solution."
OS X Mountain Lion Drivers & Software
HP provides print drivers for more than 1,500 HP peripherals worldwide using Apple Software Update. With the release of OS X Mountain Lion, we have a few troubleshooting tips prior to Expert Day, including:
For HP customers upgrading to Mountain Lion from Lion or Snow Leopard; HP print drivers and software will continue to work following the upgrade.
Additionally, HP has the largest offering of AirPrint™-compatible printers for Mountain Lion allowing easier, more efficient printing without the need to download additional software.
For customers purchasing a new Mac running Mountain Lion, HP’s latest print software for most printers, AiOs, and MFPs can be installed using Software Update in Mountain Lion.
HP software updates for the following new models are immediately available through www.hp.com/support:
HP Deskjet 2510 All-in-One Printer
HP Deskjet 3520 e-All-in-One Printer
HP Officejet 4620 e-All-in-One Printer
HP Officejet 6100 ePrinter
HP Photosmart 5520 e-All-in-One Printer
Updates for the following new models will be available in the coming weeks:
HP LaserJet Pro400 M400 series
HP LaserJet Pro 400 MFP M425 series
HP LaserJet Enterprise 500 MFP M525 series
HP LaserJet Enterprise 500 color MFP M575 series
The following models are supported using AirPrint™ within Mountain Lion.
HP LaserJet Pro P1102 Printer series
HP LaserJet Pro P1606 Printer series
HP LaserJet Pro M1217nfw MFP series
For more information regarding HP peripherals for Apple products visit www.hp.com/go/mac.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.
--Say "Thanks" by clicking the Kudos Star in the post that helped you.
--Please mark the post that solves your problem as "Accepted Solution"

Hi bkspero,
Thank you for the feedback. To address your concerns, your posts made during the Expert event can be found here:
Add ATSC channels to existing QAM lineup in Windows 7 Media Center
Delete Vista recovery partition after Win 7 upgrade
They were moved to the appropriate post-event forum and left open for responses. If you still need assistance with these issues, you may want to reply to your posts and let everyone know you're still looking for answers. This reply will serve to "bump" your threads back to the top of the first page of the forums as well.
Clicking the "Kudos star" to the left is a great way to say thanks!
When your problem has been solved, accept the solution by clicking the "Accept as Solution" button to help other members in the future!
Rules of Participation

Iphone 4s - how do I change the name in the contacts for the owner of the phone - it is coming up as the other person who uses the laptop - so when ringing or texting anyone 2 names are being used as the caller id on the screen

Iphone 4s - how do I change the name in the contacts for the owner of the phone - it is coming up as the other person who uses the laptop - so when ringing or texting anyone 2 names are being used as the caller id on the screen

*Ralph Johns* writes:
"Your options are:
Get a trial account form @mac which will work as an iChat name after the 60 days run out but not be a email account that is valid (And is free)"
Do you mean a trial account from .Mac? (DotMac)
"Get an AIM Screen name and set it to Display what you want as you set it up.
The Screen name can be whatever yu want but you can also set it to display something else as well."
I had thought about this, but it seems other people have already chosen the screen name "pinksharkmark" and virtually every variation of it I can think of. So that isn't an option for me. As for getting it to display something else as well, do you mean that if I were to get an AIM screen name like "CromulentCat" I could somehow log in to iChat under the AIM account "CromulentCat" yet get iChat to represent me to my Buddies as "PinkSharkMark"? Because I have to admit I don't see how that can be done. It appears as if iChat displays to anyone chatting with you precisely the account name you logged in under and nothing else. So if you logged in using a .Mac account, then you are displayed as "[email protected]" while if you logged in under an AIM account, you are displayed as "CromulentCat". But that's it that's all... there is no way to change CromulentCat to PinkSharkMark.
Thanks very much for taking the time to reply, though.

Life span of Clear enclosure 23 HD

Hi all,
I just love the previous version (acrylic, clear enclosure) 23" HD display as opposed to the current aluminum version. I recently purchased them used and was wondering how long I can expect these to lasts. I know things like the intensity setting, how long I have it on,etc. affects it but if you can throw in a ball park figure for an average user, that would be great. Thanks.

My 23" ACD has been going since August 2003. But it depends how people use them. Mine is for fairly heavy domestic use, but that would pale beside one used for work 12 - 14 hours a day. I also never run it at maximum brightness as I understand this will shorten the screen's life. I am fairly aggressive with my settings to power down the screen when I'm away also.

Hey, I'm fixing up a Power Mac G5 for a friend, he gave me a Cinema HD 30' display to use with it. My problem is, the Power Mac G5 doesn't have a place where I can plug in one of the display's cords. the cord is called a "DC power (24.5 V)"

So the Cinema HD's DVI goes in fine, I don't remember what video card is in the computer, all I know is it's Nvideo, it's old, only like 256MB, but does have two DVI ports. Anyway, then the display's firewire and USB can go in. But there's this weird thing, had to do some research to figure out what the connector/cord is called. it's the size of a USB, rectangular with oval sides. It's called a "DC power (24.5 V)" I'm like, what the heck is this thing? it won't go into the computer anywhere, I'm assuming I need some sort of adapter?? Help please, if I need an adapter or video card, links would be extremely helpful.
Best regards,
Poly

I don't believe so, I have a DVI to ADC adapter I was messing with, my DVI from the display plugs into the adapter, then i grap the adapter's ADC connector, and it does not go into my Power mac G5's video card. So that confirms that the display is DVI, and works with my DVI video card perfectly. It's just the one wire/connector that apple calls the "DC power (24.5 V)" that won't go in anywhere. Basically the display has a DVI connector, firewire connector, and USB, which all go into my Power mac G5 fine. However, it has another wire with a connector that won't go in anywhere, from what I've read off the teach specs of my Cinema HD 30' that final connector/wire is listed as "DC power (24.5 V)"
So my problem is with that. I have NO idea what it does, or goes into. When I google "DC power (24.5 V) Apple" it comes up with weird images none of which have that connector. So I'm just so. Confused.

Report for material gr/ir clearing account display differences

report for material gr/ir clearing account display differences

hi salsa,
There is no such report for the datails of material gr/ir ......
but T code J1ILN and select
Indirect taxes -
> Register -
> Excise tax -
> In J1IN Update Excise register RG23a -
> then Extract rg23a----- > PRint utility program Rg23a
here u can extract all the invoices gr/ir
Through
T code J1I5
J2I5
J2I6
if useful assign points...
regards,
santoshkumar

How can I automatically "retract" all windows from my Thunderbolt display back to my MacBook Air when I disconnect the display, esp if the Thunderbolt is the desktop with the white menu bar?

I am in and out of my office with my MacBook Air. I would like to set it up so when I plug in my Thunderbolt display in the office, the Thunderbolt display has my desktop, menu bar and the open windows. If I set the Thunderbolt display to mirror by MacBook Air it adjusts to the lower resolution of the MacBook Air, which is a waste of a cool monitor. I can set it up as an extended desktop and drag the white menu bar to the Thunderbolt display so it displays my desktop but if I then disconnect my MacBook Air, the menu bar is absent and all the windows that were seen on that display are absent, as if it I was still attached to the larger display. The only way around this is to go to Thunderbolt display preferences, drag the white menu bar back to the smaller display and manually drag all windows to the smaller display before disconnecting. Doing this multiple times per day is a real pain. Is there a way to set my MacBook Air to recognize when it is attached to the Thunderbolt display and automatically my desktop and all open windows to it and then do the same process in reverse when I unhook it?

It's definitely not supposed to work like that...when you plug the display in, it should just turn on and adjust your displays. It works like that on my MBP. Kind of a silly question, but do you have the MagSafe from the display plugged in your MBAir too? Thats a requirement. Beyond that, it should "just work."
Not sure if there is some setting to enable...i haven't seen it. Call to support?

Using the transaction launcher to call a BOR method to display a PDF

Hello gurus,
I have created a PDF icon and an onclick action to open a pdf, that displays on every row of an assignment block in the actions column, but I do not know the technical process to determine how to get a PDF from the IXOS system from the line selected. (even if I know it depends on an ID attribute of that assignment block) I want to to call a transaction launcher with the url for the pdf in the IXOS that has an ID that identifies which line in the assignment block the user has clicked the pdf icon for (does that make sense?)
In CRM 4, in the collection factsheet assignment block, the link was coded into an XSLT which is then displayed in the GUI and you would have a clickable link for a pdf file in a row in a table. That link would be as follows:
         <xsl:variable name="ev_key">SAPEVENT:?OBJTYPE=<xsl:value-of select="attributes/OBJTYPE"/>&OBJKEY=<xsl:value-of select="@KEY"/>&LOGSYS=<xsl:value-of select="attributes/LOGSYS"/></xsl:variable>
             <a href="{$ev_key}"></a>
This will get the file in IXOS and display it, in CRM 4. In CRM 7, the link is an icon in every line of an assignment block.
Here are some questions I have now for the functional side in the meantime:
1) Can we fetch the PDF in IXOS for each line of an assignment block and have it open? If so, how? Transaction launcher, function modules (like ARCHIVOBJECT_DISPLAY) in the OPTA package? (the package for all IXOS related function modules..)
2) Which URL should I call with the transaction launcher? a URL link to the PDF on the IXOS system?? or sapevent:xxx?
3) Do we have to configure a transaction in the IMG to be launched with the attributes listed there? Do we have to link it to any classes/ objects?
4) Do we have to have the code to the logical link dynamically to call the right PDF for each table line? Is it right to put this code in my event handler?? Usually transaction launchers are just in the nav bar.....
5) Are there any existing examples of this or a similar functionality/ logic that I could refer to, preferably in CRM 7 WebUI?
6) Do you have any code to just display a PDF in a new window? Or prompt a download?
One possible way I thought of would be for me to have a logical link defined in the IMG for the transaction launcher, and have the attributes defined for my BOR object that I would call, and pass it different attributes (eg. objtype, objkey, logsys...) and then return the PDF and display it in the UI in a new browser window by itself. (There is a BOR method for my BOR object named 'display_pdf'!!!!)
What do you think would be the optimal solution here? Does my theory of calling a BOR object with a transaction launcher to display a PDF make ANY sense whatsoever???
Please do not hesitate to propose any potential solution. Any partial answers/ links to wikis/ other threads, anything would be much appreciated.
Thank you in advance.
Best regards,
Jonathan Laplante
Edited by: Jonathan Laplante on Jul 2, 2011 4:50 AM

Hi Any help on this....I am still awaiting the response.
Requirement: My requirement is to launch the SE38 transaction on WEBUI using transaction luncher tool and set the parameter on the selection screen.
Issue: The issue is that I am able to lunch the transaction but unable to set the parameter
Steps Performed:
I want to list down all the steps I performed to launch an SE38 transaction using transaction launcher on the WEBUI
1) Defined logical system in tcode CRMS_IC_CROSS_SYS
-The logical link looks like this
http://<server>:<port>/sap/bc/gui/sap/its/webgui/!?transaction=IC_LTXE&okcode=ICEXECUTE ?sap-client=300
2) Defined URL & paratemeter wherein the request method is "GET", opted for NON-BSP URL
URL link here is
http://<server>:<port>/sap/bc/gui/sap/its/webgui/!?transaction=SE38&okcode=ONLI
-Note: My selection screen okcode os ONLI*
-The logical system ref is provided here
3) Defined the parameter by giving the screen name like for SE38 selection screen name is "RS38M-PROGRAMM"
4) Configured the transaction launcher of type B - URL type and provided the reference of the URL ID, choose the relevant parameter from the drop down and have hardcoded the value, cheked the box "Save Data in Activity Clipboard
5) Added this in the NAvlink/Bus Role etc
6) Now in the handler class of the TL the code looks like this:
IF_CRM_IC_ACTION_HANDLER~PREPARE_DATA_FLOW
__gdc ?=
cl_crm_ui_data_context_srv=>get_instance( gv_view_controller ).
__value
=
'ZC_TEST'.
add_parameter(
   iv_name =
'RS38M-PROGRAMM'
iv_value = __value ).
However, after performing the above steps I am unable to set the parameter. Please suggest where am I missing out on. An early response would really be appreciated.

HT5557 hello...my questions is related to objective C...Is it possible to display name of the person who is calling me whose number is saved in my local database but not in iphone contacts ?.

hello...my questions is related to objective C..
Is it possible to display name of the person who is calling me whose number is saved in my local database but not in iphone contacts ?.

ashish35,
No one from Apple here - we're just users like you. All I can tell you is that electronic fail and with MacBook Pros (and most notebooks) the components are so integrated as to make a repair to the logic board practically impossible, hence the high prices charged for repairs.
Only you can decide if you want to have your computer repaired or put the money towards the purchase of a new computer. If you do decide to purchase a new unit I would suggest that you also purchase the AppleCare Protection Plan which increases your warranty from one year to three years.
Sorry and good luck,
Clinton

Called party number on phone display - updating with results of translation on GW, not wanted

Call Manager 9.x, IOS 15.1, H.323 gateways
Hi, I've got 2 questions regarding the called number display on handsets. Essentially, when a user dials an external number it's obviously shown on their phone handset screen - when that number is manipulated to add prefix for certain PSTN gateways etc. the updated number is shown on the phone display, which the users identify as "not the number I dialled" - can this be changed?
It a cosmetic issue essentially, but one I am being asked about and can't find an answer to:
1) I add a prefix on the gateway to the outbound dialled number (to add a carrier code / network function to all calls) - ie, \^9!\ \1666\ - Process looks like this:
user dials -> 912345
shows as dialled number on handset -> 912345
translation-rule on gateway (in IOS) converts number to -> 166612345
call connected
user handsets now updated to show dialled number as -> 166612345 (but still wanted it to show 912345)
2) Another seperate scenario is that I am doing called party transformation on a route pattern - here the modified number is shown instantly on the callers display. Presumably this in unavoidable? Or, can the original number dialled by the user be displayed on their phone, not the modified one?

Hi,
any calling or called transformation in the route pattern appears in the screen.
you can discard the 9 in the route pattern and add prefix 9 in the route list level.
for the 2nd point there is a service parameter in the call manager to keep the original dialed number
HTH
Anas
don't forget to rate the helpful posts

Firefox doesn't display content, especially links.

This is my problem in a screenshot: http://d.pr/i/DjkB
The content isn't displayed and especially links. Links are always not there and sometimes text is displayed but all websites are disfunctional because of this.
Here's a link to a screenshot displaying how the same website should look like: http://d.pr/i/ZRvN

Did you manage to find out which font Firefox is using in the case when text doesn't display?
You will have to remove or update that font.<br />
You can also check that font in Fontforge.
*http://fontforge.sourceforge.net/

Calling on all clear enclosure display owners; especially the 23" HD displ

Similar Messages

Maybe you are looking for