Calling Party translation internal and external

Hello all!
I have a problem regarding the external phone number mask and some special requests.
Basically is the feature "external phone number mask" enabled and in use.
Now we have the following request:
Several phones are member of a hunt list, with the extension 555. They want now two groups, one should show internal and external the 555. And the other one should show internal the 555 and external the "normal" extension of the user.
Overview, showing the numbers:
Phone group 1:
external: 555
internal: 555
Phone group 2:
external: line extension
internal: 555
Used is CUCM 8.6 and MGCP-Gateways to the PSTN.
Has anyone an idea to configure that?
Thanks a lot!
Kind regards,
DrMxxxxx

Ah, got it. Well here's how you do it then:
Create a Partition for e.g. PT-CallingParty and put it in CSS-CallingParty.
Create a Calling Party Transformation Mask as following:
4912345XXX with PT-CallingParty
Check Mark "Use Calling Party's External Phone Number Mask"
Under Calling Party Transformation Mask put "4912345555"
Now, for phones:
Go under each phone and under Number Presentation Transformation Uncheck "Use Device pool Calling Party Transformation CSS" and from dropdown just above it Select " CSS-CallingParty" (Apply config, I will suggest BAT for this if you have multiple phones)
Once done that, For User A put External Mask as 4912345555
Whereas for User B put 4912345456
Let me know how that works out for you.
Regards,
Vishal

Similar Messages

CWMS 2.0MR7 intermittent dead air on call-in and call-back for internal and external users

Hello,
I have got a new install of CWMS 2.0MR7 800 users non HA system. During initial testing we noticed that when we call-in or call-back there was a dead air even though the call is connected we don't hear welcome to WebEx....when we hang up and call again it works fine and we hear welcome to WebEx so the issue is intermittent. CUCM version is 8.6
Can someone please advise how do we go about troubleshooting something like this when the issue is so intermittent?
Thanks

Hi,
Please check the following:
1. Please check if you are on supported hardware and that no co-resident VMs exist:
http://www.cisco.com/c/en/us/td/docs/collaboration/CWMS/2_0/Planning_Guide/Planning_Guide_chapter_01011.html#reference_249B138B71324D19B09141D3849EC058
2. Check if you have any snapshots on any of the virtual machines for the system. If you have captured any snapshots before an upgrade, make sure that you delete them within 24 hours as they cause degradation of system performance and are known to cause audio quality issues.
3. Please check your network bandwidth for these requirements:
http://www.cisco.com/c/en/us/td/docs/collaboration/CWMS/1_5/Planning_Guide/Planning_Guide_chapter_01.html#reference_267DB686BB224EB7A49DE4C783C912E6
If you still face the problem, please open a TAC case to troubleshoot the issue further. We will be able to get detailed logs and sniffers to find the cause of the issue.
Thanks,
Jyothi

Cannot install Yosemite as it keeps telling me both my internal and external drives are time machine backups

Cannot install Yosemite. Keeps telling me that both my internal and external
drives are backing up with TIme Machine. Any suggestions?

Is it actively backing up, or are you encountering a dialog stating that Yosemite cannot be installed because the disk is being used for Time Machine backups?
Read OS X: Cannot install on a volume used by Time Machine for backups
If for some reason you have a folder called Backups.backupdb at the root level of the hard disk on which you want to install Yosemite, move it to the Trash.

Difference between internal and external organizations in oracle hr

Hello,
While creating an organization, when do we use Internal and External? Basically whats the difference between these two options in the Work Structure screen while defining organizations?
Thank You
Kumar

Hello,
Just to add on information.
Internal organizations are such as departments, divisions, and sections
External organizations are such as benefits carriers, tax authorities, and recruiting agencies.Organization classification Payee Organization when defining an external organization that is the recipient of a third party payment from an employee, for example a court-ordered payment. You can then select this organization on the Personal Payment Method window when entering a third party payment method.
Generally we do not tag employees(Organization classification HR Organization) to external organizations.
Regards,
Saurabh

Single URL for internal and external CRM access when using IFD

Hello,
At one of our client site I have setup IFD on CRM 2011. This IFD is behind TMG. My client is a big corporation therefore all CRM components including CRM, ADFS and SQL are on separate servers.
I have configured IFD using single url https://orgname.contoso.com Their IT staff wants to know why can't they use single URL for internal and external access where internal users are nto prompted for authentication
when logging on to the CRM server. I know you can do URL re-write in ADFS but they want to know the reason "why internal users can't use the same IFD URL and don't get prompted for their credentials". Text below is from their IT staff.

There are several approaches to your question. You need to set up both an internal and an external relying party trust. If you use the external URL, it will always direct you to the signin page, if you use the internal URL, it will resolve you single
sign on.
I've configured IFD for CRM multiple times, and this is how it works. CRM looks at the URL. If you use the external URL (org.domain.com), it will prompt for credentials. So what you are asking for, a single URL that works single sign on internally and prompts
externally really isn't possible.
What I recommend is:
1. make the external URL available internally
2. Configure all outlook clients against the external URL, that way you won't have to reconfigure when someone goes internal to external
3. Have users who are primarily internal use the internal URL for the web client, which will resolve single sign on
4. Have users who are primarily external use the external URL for the web client
For #1, since you only need to enter the credentials when you first configure CRM, it is in all effects single sign on.
One thing I haven't tried that may work is using IIS redirect internally to redirect the external URL to the internal URL. There is also a powershell script in the IFD guide that you can use to make the outlook client switch between the internal and external
URL's, but nothing that will give you a single URL that works as the internal relying party trust when internal and the external relying party trust when you are external.

DNS Forwarding Same Internal and External Zone

Hi,<o:p></o:p>
So we have decided that we want our internal domain to be the same as our external domain e.g. domain.uk. I understand that split DNS can be used
to fulfil this requirement but is it possible to set up a forward so if the DNS entry is not available in the internal zone it will forward onto one of our external name servers where it can resolve?<o:p></o:p>
We are basically trying to avoid having to add the entry on both external and internal DNS servers for it to resolve. So far I have added the external name servers to
the forwarders and disabled root hints which didn’t work. I’ve tried to add a conditional forwarder but it says the zone already exists. It seems the only to achieve the internal resolution is by creating the DNS entry both internally and externally.<o:p></o:p>
Does anyone know if this is the case? It seems strange that you couldn’t point the DNS to another external name server for resolution? <o:p></o:p>
Any help would be appreciated.<o:p></o:p>

You must ask in networking forum
https://social.technet.microsoft.com/Forums/en-US/home?forum=winserverNIS&filter=alltypes&sort=lastpostdesc

Delivery report shows status of Pending for external address. Email sent to both internal and external addresses.

We have an Exchange 2013 on-premise server and seem to have an issue with emails sent to internal and external users at the same time.
The issue came to light because someone sent an email to 44 recipients, of which one was internal. None of the external recipients received the email. I checked the delivery report in the EAC and found the internal email marked as 'Delivered' and all of
the external ones marked as 'Pending'. I checked the queues and there were none. I did some testing and sent an email to just one of the external addresses on the list, it arrived. I tried sending the email again to all of the recipients, the external ones
all showed 'Pending'. I tried it again, but this time excluded the internal email address and all of the 43 external emails were immediately delivered.
So it seems that the issue only arises when we are sending to both internal and external addresses.
I then tried a test email to one internal address and one external address. The Delivery report says that the internal address was delivered immediately, while the external address is 'Pending' and gives more information saying: 'Message delivery is taking
longer than expected. There may be system delays. For more information, contact your helpdesk.'. To add further mystery to this, the email was actually delivered.
So, I have two concerns:
First is seems that some emails sent both internally and externally are only arriving internally. This is a huge problem because I don't know how many have been affected. There may be many lost emails we don't know about.
Second, it looks like I can't trust the delivery report. It says pending for some emails which didn't arrive, but it also says pending for some which did arrive. That is no good at all.
For info the server is running Windows Server 2012. I have run a Microsoft Update to check if there are any to apply and the only Exchange one is a spam filter update, which I doubt has any bearing but I will apply when I get chance.

Hi Neil,
According to the description, I find a related KB on Exchange 2010:
https://support.microsoft.com/kb/2694474?wa=wsignin1.0
It has the similar situation as yours.
This issue occurs because a function in a message tracking component tries to obtain the information for the recipient instead of the external recipient.
Please try to upgrade to the latest Exchange update to check whether this issue can be solved.
Also please check whether Throttling has been set.
Please run "Get-TransportService | fl" to check the MaxOutboundConnections parameter value.
More details to see:
Message throttling
http://technet.microsoft.com/en-us/library/bb232205(v=exchg.150).aspx
Thanks
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Mavis Huang
TechNet Community Support

Can I split my itunes music library between and internal and external hard drive?

Is it possible to have music on the two different drives and still be able to make playlists from both drives to put on my ipod? Here's my situation: I'm using a Dell 32 bit computer running Vista Home Premium SP2 which I share with other users. I have a large itunes library (40g+ of music only) that's starting to hog the hard disk space from other users. If possible, I would like to split off part of my itunes library to an external hard drive while still having access to the entire library for my ipod. Ideally I would like to have all my downloaded songs on both the internal and external drives so I'll have backups in case a drive fails, while putting all the music I have hard copies of solely on the external drive. Any help on how this can be done would be appreciated.

If you manually manage your itues library, you can store parts of it on an external drive, or on an internal drive. Just keep in mind that in iTunes that you must set a default location for iTunes to manage it's files, and that will be the default location for iTunes to store anything it downloads. You would need to manuay manage moving things from there if tht is not where you want them stored.
Perhaps a "better" solution would be for you to invest a little mone into 2 external drives. One to hold your entire iTunes library, and the second to be your off-line backup of the first. This is the method I have gone with and I like how it works for me. My entire iTunes library is on an external (portable) 320GB drive. Then, when iTunes is not running, I will clone my external drive onto a second drive I happen to have, this way if I have any failure of my primary drive, I lose at most about a weeks worth of content. For me, I purchase little content during a week, but I do move a fairly large volume of podcasts. With the entire library being on the external drive, if I ever have to swap to using my backup drive iTunes wil just think that it hasn't run and downloaded anything for a week, and all the "lost" content will be re-downloaded automatically. This won't work for apps or purchased content, but for subscribed podcasts, it is great.

SharePoint 2013 - Office Web Apps - Internal and External Use

I have successfully installed SharePoint 2013 and Office Web Apps on Azure VMs inside an Azure Virtual Network (IaaS model). Everyting is working well. However, my testing has shown that external users and internal users can't use Office Web Apps at the
same time.
Office Web Apps, installed on its own vm, accomodates an external and internal URL quite well. However, SharePoint 2013 appears to only allow one setting for WOPI Zone, either internal or external but not both. I've set the WOPI zone to Internal-HTTPS (Set-SPWOPIZone
–Zone “internal-https”). OWA works just fine if accessed from inside the Azure Virtual Network. However, if I try to access from outside the Virtual Network, from the Internet, Office Web Apps fails. The exact oppisite is also true. I can set WOPI Zone to
External-HTTPS and accessing from the Internet works fine, but accessing inside the Virtual Network fails.
Am I missing something? I, obviously, want Office Webs Apps to function properly for both internal and external users simultaneously.
I appreciate any help anyone can provide here.
Glenn

Hi Glenn,
To have both the use of Internet and Internal available to your end-users, you first need to configure AAM setting. Open Central Administration > Application Management > Configure alternate access mappings. Let's say there is an existing web application
named http://sharepoint and my end-users from local network are able to access it using the URL http://sharepoint (root site collection). Here you need to add the Internet URL by select the web application and click Edit Public URLs. Add the Internet domain
to the web application, e.g http://sharepoint.abc.com. You don't necessarily have to edit binding setting in IIS. Before continuing next steps, make sure you are able to access http://sharepoint.abc.com from the Internet while being able to access http://sharepoint
from local network (aka Internal).
On the machine where Office Web App (OWA) Server 2013 is installed, open PowerShell to add OWA module and use the following command to re-create a new OWA server farm if you've completed configuring it previously.
New-OfficeWebAppsFarm -InternalUrl "http://owa" -ExternalUrl "http://owa.abc.com" -EditingEnabled.
In this case, I'm not using SSL certificate to encrypt data over the Internet. You can use Internet-public IP of the OWA server like -ExternalUrl "http://198.xxx.xxx.xx". Add CertifcateName parameter if you want to use whether CA-issued certificate
or self-signed certificate.
On your SharePoint machine, you need to re-bind all WFE machines to WAC farm using the cmdlet New-SPWOPIBinding. Next, you need to set the WOPI zone for both internal and external.
Set-SPWOPIZone -zone "external-http"
Note: I'm not all using certificate in my guidance. But the steps to have it configured is just to add more parameter.
I've recently successfully deployed OWA multi-server farm for both internal and internet uses for two big clients. In real-world scenario, ideally OWA should be published through firewall (Forefront UAG, TMG, F5...etc). Please let me know if you still have
issues after following my steps. My email: [email protected]
Regards,
-T.s
Thuan Soldier
A 23-year-old man loving Microsoft technologies and making crazy ideas on business journey.
SharePoint Vietnam |
Blog | Twitter

Front End internal and external web services

Hi all,
Can someone explain the purpose of internal and external web services URL in front end server. what does it do and what is it used for? and why the external traffic goes directly to it and not through reverse proxy?
Thanks,

They're for multiple purposes. Address books, autodiscovery, meeting urls, mobile clients, etc. There are two because they respond slightly differently based on whether the client is internal or external. External traffic should always reach
it through a reverse proxy, that reverse proxy should proxy traffic received on port 443 to port 4443 on your front end pool.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications
This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

How to configure AD on windows 2012 server for Exchange 2013 internal and external email flow

Dear Experts,
I have to configure exchange 2013 on Windows server 2012 STD. Company has registered Static IP addresses and can get the MX record pointing to any of this Static IP.
The registered domain name is e.g. contoso.com.
a. What should I use as domain name on AD? contoso.com or contoso.local
b. Is it recommended to have two different servers for AD and Exchange?
c. What should be my connector settings for mail flow?
d. how can I set 2 email servers in company for load balancing?

Hi,
a, I suggest use contoso.com as domain name. It is convenient to add urls into our certificate for internal and external mail flow.
b, Recommended that installing AD
and Exchange Server on two separate
Servers. If Exchange Server downed unfortunately, it can prevent AD server from crushing at the same time.
c, Found some articles for your reference:
Configure Mail Flow and Client Access
http://technet.microsoft.com/en-us/library/jj218640(v=exchg.150).aspx
Configuring Outbound Mail Flow in Exchange Server 2013
http://exchangeserverpro.com/configuring-outbound-mail-flow-in-exchange-server-2013/
d, Load Balancing
http://technet.microsoft.com/en-us/library/jj898588(v=exchg.150).aspx
Hope it is helpful
Thanks
Mavis
Mavis Huang
TechNet Community Support

Leopard. Did a full restore from Time Machine. Now I can't access my other internal and external drives. I get the following error: The folder "Capture Video" can't be opened because you don't have permission to see its contents.

Leopard. Did a full restore from Time Machine. Now I can't access my other internal and external drives. I get the following error: The folder “Capture Video” can’t be opened because you don’t have permission to see its contents. I have repaired permissions pn the main harddrive. When I try too click on a disk I get the previously stated error. I can't even open up information to see what permission/access there is. It simply will not let me see the content. It shows the content of my main hard drive when I have clicked the other harddrive's name.

Solved:
sudo chflags 0 /Volumes/"FCP Time Machine BU"
sudo chown 0:80 /Volumes/"FCP Time Machine BU"
sudo chmod 775 /Volumes/"FCP Time Machine BU"
sudo chmod -N /Volumes/"FCP Time Machine BU"

Cisco ISE with both internal and External RADIUS Server

Hi
I have ISE 1.2 , I configured it as management monitor and PSN and it work fine
I would like to know if I can integrate an external radius server and work with both internal and External RADIUS Server simultanously
So some computer (groupe_A in active directory ) will continu to made radius authentication on the ISE internal radius and other computer (groupe_B in active directory) will made radius authentication on an external radius server
I will like to know if it is possible to configure it and how I can do it ?
Thanks in advance for your help
Regards
Blaise

Cisco ISE can function both as a RADIUS server and as a RADIUS proxy server. When it acts as a proxy server, Cisco ISE receives authentication and accounting requests from the network access server (NAS) and forwards them to the external RADIUS server. Cisco ISE accepts the results of the requests and returns them to the NAS.
Cisco ISE can simultaneously act as a proxy server to multiple external RADIUS servers. You can use the external RADIUS servers that you configure here in RADIUS server sequences. The External RADIUS Server page lists all the external RADIUS servers that you have defined in Cisco ISE. You can use the filter option to search for specific RADIUS servers based on the name or description, or both. In both simple and rule-based authentication policies, you can use the RADIUS server sequences to proxy the requests to a RADIUS server.
The RADIUS server sequence strips the domain name from the RADIUS-Username attribute for RADIUS authentications. This domain stripping is not applicable for EAP authentications, which use the EAP-Identity attribute. The RADIUS proxy server obtains the username from the RADIUS-Username attribute and strips it from the character that you specify when you configure the RADIUS server sequence. For EAP authentications, the RADIUS proxy server obtains the username from the EAP-Identity attribute. EAP authentications that use the RADIUS server sequence will succeed only if the EAP-Identity and RADIUS-Username values are the same.

Setup internal and external DNS namespaces best practice

Is external name space (e.g. companydomain.com) and internal name space (e.g. corp.companydomain.com or companydomain.local) able to run on the same DNS server (using Microsoft Windows DNS servers)?
MS said it is highly recommended to use a subdomain to handle internal name space - say corp.companydomain.com if the external namespace is companydomain.com. How shall this be setup? Shall I create my ADDS domain as corp.companydomain.com directly
or companydomain.com then create a subdomain corp?
Thanks in advanced.
William Lee
Honf Kong

Is external name space (e.g. companydomain.com) and internal name space (e.g. corp.companydomain.com or companydomain.local)
able to run on the same DNS server (using Microsoft Windows DNS servers)?
Yes, it is technically feasible. You can have both of them running on the same DNS server(s). Just only your public DNS zone can be published for external resolution.
MS said it is highly recommended to use a subdomain to handle internal name space - say corp.companydomain.com
if the external namespace is companydomain.com. How shall this be setup? Shall I create my ADDS domain as corp.companydomain.com directly or companydomain.com then create a subdomain corp?
What is recommended is to avoid having a split-DNS setup (You internal and external DNS names are the same). This is because it introduces extra complexity and confusion when managing it.
My own recommendation is to use .local for internal zone and .com for external one.
This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Get Active Directory User Last Logon
Create an Active Directory test domain similar to the production one
Management of test accounts in an Active Directory production domain - Part I
Management of test accounts in an Active Directory production domain - Part II
Management of test accounts in an Active Directory production domain - Part III
Reset Active Directory user password

Unable to activate internal and external urls at the same time

Hi,
We have Configured EBS R12 in DMZ setup as described in Figure F-9 of metalink note 380490.1 ,Option 2.4: Using Reverse Proxy with no External Web Tier.
refering to 726953.1 Case History: Implementing a Reverse Proxy Alone in the DMZ Configuration - R12.
but Not able to activate internal and external urls at the same time in this configuration. Only the node where last autoconfig was run getting activated as web node.
When trying to accees the url of the other node it gets redirected to the url (where autoconfig is last run).and for this error observed is Error Code:502 Proxy Error.The specified Secure Sockets Layer (SSL) port is not allowed.(12204).
For both external and internal services are UP.opmn status is live no error.
Using Apache as reverse proxy.
EXTERNAL Reverse proxy settings:
s_login_page http://LONWEB01.process.com:81/OA_HTML/AppsLogin
<TIER_DB oa_var="s_isDB">NO</TIER_DB>
<TIER_ADMIN oa_var="s_isAdmin">NO</TIER_ADMIN>
<TIER_WEB oa_var="s_isWeb">YES</TIER_WEB>
<TIER_FORMS oa_var="s_isForms">YES</TIER_FORMS>
<TIER_NODE oa_var="s_isConc">NO</TIER_NODE>
<TIER_FORMSDEV oa_var="s_isFormsDev">YES</TIER_FORMSDEV>
<TIER_NODEDEV oa_var="s_isConcDev">NO</TIER_NODEDEV>
<TIER_WEBDEV oa_var="s_isWebDev">YES</TIER_WEBDEV>
INTERNAL Middle Tier settings:
s_login_page http://stprojapp01.test.com:8005/OA_HTML/AppsLogin
<TIER_DB oa_var="s_isDB">NO</TIER_DB>
<TIER_ADMIN oa_var="s_isAdmin">YES</TIER_ADMIN>
<TIER_WEB oa_var="s_isWeb">YES</TIER_WEB>
<TIER_FORMS oa_var="s_isForms">YES</TIER_FORMS>
<TIER_NODE oa_var="s_isConc">YES</TIER_NODE>
<TIER_FORMSDEV oa_var="s_isFormsDev">YES</TIER_FORMSDEV>
<TIER_NODEDEV oa_var="s_isConcDev">YES</TIER_NODEDEV>
<TIER_WEBDEV oa_var="s_isWebDev">YES</TIER_WEBDEV>
Are we missing anything....
Thanks & Regards

Hi,
Finally it's resolved...Following is the solution thought to share in the forum:
The configuration of the E-Business Suite environment for DMZ requires profile options hierarchy type to be set
to SERVRESP.
To change the profile options hierarchy type values to SERVRESP, execute the following SQL script as
shown below:
sqlplus / @/patch/115/sql/txkChangeProfH.sql SERVRESP
After successfully completing the above sql script, run Autoconfig in all nodes to complete the profile options configuration.
It's resolved after doing this..

Calling Party translation internal and external

Similar Messages

Maybe you are looking for