Callmanager 4.3 and McAfee Host Intrustion Prevention

Will Callmanager 4.3 support McAfee Host Intrustion Prevention 7.0? Or will it completely hose it? Yes or no, is there any documentation supporting this conclusion. I've been searching the web to no avail and this seems to be the only place to get some assistance.
I would greatly appreciate the help.
Thanks and have a great day!

Here is whats supported
http://www.cisco.com/en/US/customer/prod/collateral/voicesw/ps6788/vcallcon/ps556/prod_bulletin0900aecd800f8572.html
TAC will probably tell you the same thing... if its not on the list, probably dont use it or use at your own risk

Similar Messages

Premiere Elements 12 will not launch while using McAfee Host Intrusion Prevention Service

We are planing to use Adobe Premiere Elements 12 in our corporate enviornment and it appears as though the product installs without issue but fails to launch. After troubleshooting the issue it appears as though the application is trying to do something that the McAfee Host Intrusion Prevention Service is catching and thus preventing the application from launching. If the McAfee HIPS service is stopped the application will launch without issue - so far we have been unable to identify the reason for this and were hopeful this may have been brougt up before?

keehola
I am not sure if you aware but we are not Adobe here at the Adobe Premiere Elements Forum. Rather user to user.
If you want Adobe, then you will need to contact it through its Adobe Chat.
Contact Customer Care
I have setup the link for
Premiere Elements
Adobe ID and Sign In
Adobe ID, Sign In, Account Help
Chat Panel (it currently has an active Panel)
If the link does not hold its set, then you will need to navigate the link to Chat Panel using the above titles as guides.
Because of the complexity of your issue, I strongly encourage you to contact McAfee.
I am in no way affiliated with McAfee or Adobe.
ATR

Cisco ASA 5505 Cannot ping local traffic and local hosts cannot get out

I have, what I believe to be, a simple issue - I must be missing something.
Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209).
There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off.
The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue.
Basically, the VPN is up and running but PC 10.51.253.210 cannot get out.
Any ideas? Sanitized Config is below. Thanks !
ASA Version 7.2(4)
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif Inside
security-level 100
ip address 10.51.253.209 255.255.255.248
interface Vlan2
nameif Outside
security-level 0
ip address ***** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name *****
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
pager lines 24
mtu Outside 1500
mtu Inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any Outside
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list No_NAT
route Outside 0.0.0.0 0.0.0.0 ***** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set DPS_Set esp-3des esp-md5-hmac
crypto map DPS_Map 10 match address Outside_VPN
crypto map DPS_Map 10 set peer *****
crypto map DPS_Map 10 set transform-set *****
crypto map DPS_Map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
console timeout 0
management-access Inside
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group ***** type ipsec-l2l
tunnel-group ***** ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8d0adca63eab6c6c738cc4ab432f609d
: end
1500

Hi Martin,
Which way you are trying. Sending traffic via site to site is not working or traffic which you generate to outside world is not working?
But you say ASA connected interface to PC itself is not pinging that is strange. But try setting up the specific rules for the outgoing connection and check. Instead of not having any ACL.
If it is outside world the you may need to check on the NAT rules which is not correct.
If it is site to site then you may need to check few other things.
Please do rate for the helpful posts.
By
Karthik

I receive numerous messages in "Bulk Mail". Where do they come from and how can I prevent them from being received? Thanks

I receive numerous messages in "Bulk Mail". Where do they come from and how can I prevent them from being received? Thanks

Once you're on a spammer's list, there's nothing you can do to stop the flood of e-mail messages. You can either control it, using spam filtering (which is what files those messages in the Junk Mail folder), or you can throw out your e-mail address and get a new one.
It's sad, but spam is simply a fact of life at this point, and there's nothing to be done about it. Legislation has been tried, with zero success, since most spam either comes from countries with no legislation or from personal computers that have been infected with malware and are part of a "botnet."

I'm having some difficulty with Time Machine. It appears to be deleting backups from random dates on my external hard drive. I am not deleting them. Are they hidden and how do I prevent this from happening? Can I retrieve them?

I'm having some difficulty with Time Machine. It appears to be deleting backups from random dates on my external hard drive. I am not deleting them. Are they hidden and how do I prevent this from happening? Can I retrieve them?

... I didn't know that Time Machine was more a last resort back up instead of main back up.
Don't rely upon Time Machine to the exclusion of all else. I compliment Time Machine with a periodic "clone". TM is much better than nothing, but it's a safety net, not a hammock
Here is my understanding of Time Machine's file deletion algorithm, distilled from Pondini's FAQ, Apple's KB articles, and my own observations.
Time Machine deletes ("thins") files from the backup disk as follows:
Hourly backups over 24 hours old, except the first backup of the day
Daily backups over 30 days old, except the first backup of the week
Older backups get deleted when Time Machine requires space and you deleted them from the source disk.
Therefore, assuming TM has been performing at least one backup per day, backup files will remain available:
at least thirty days, if they existed on your Mac for at least a day
until you run out of space, if they existed on your Mac for at least a week
In addition to the above, Time Machine always keeps one complete copy of your source disk so that the entire volume could be restored if necessary. Any files that remain on your source volume will be present on the TM backup, no matter how old they are.
If you are using 250 GB of space on your source disk, its Time Machine backups are likely to require at least twice that much. A good estimate of the minimum required backup volume size would be about three times the size of your source disk - 1.5 TB in your case.
A more thorough explanation would require Pondini since he has plumbed Time Machine's mysteries far more than I have.
http://support.apple.com/kb/HT1427

How to install the driver of the 'SCSI and RAID Host Controller'

Hi,
I have two Windows XP(32Bit) installations:
•Windows XP SP2(32Bit) which is old and it seems as if it is infected by some viruses.
•I have installed another fresh clean Windows XP(32Bit) SP3. However, I have found that there is no category named with ''SCSI and RAID Host Controller'. However, when checking out the old version of Windows XP, I found 'SCSI and RAID Host Controller'
is there. (Screen shot below)
The new Windows XP(32Bit) SP3, there is no 'SCSI and RAID Host Controller'
My motherboard is:
My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card with 256MB of RAM.
]I am seeing that most computer doesn't has the scsi / raid controller . in the old Windows XP on my computer that SCSI and RAID controller exists, and it it has not a yellow mark on it.
When I installed a new windwos XP 32Bit SP3, no SCSI/RAID in divice manager .
My computer sound on new Windows XP doesn't work , however, on old Windows XP SP2 works well. I have a buitl-in sound card. SCSI and RAID controller category in the device manager on the old Windows xp SP2 is realted to sound card,I don't think.
Thus, What drivers would let the 'SCSI and RAID Host Controller' added in the device manager?
A man should convert his anger and sadness into strength to continue living in this life.

If you open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on the pcb somewhere. You should also normally see this information on the first POST screen when you turn on the PC.
Otherwise Google "775i65G" like I did.
Here are the driver downloads (assuming it is an Asrock 775i65G R2.0 and not an R3.0)
http://www.asrock.com/mb/Intel/775i65G%20R2.0/?cat=Download&os=XP
You should install the inf driver first. Hopefully after you do that you will see your desired listing in Device Manager.
With regard to the AMR driver and the HDMR driver, you can find some information about these here :
http://en.wikipedia.org/wiki/Audio/modem_riser
Unless you actually have something plugged into these risers, it is probably not necessary to install the drivers.
However, the drivers for the integrated C-Media audio chip and the Realtek Lan chip may prove useful.
It looks like the motherboard has integrated video but if you are using a graphics card it will not normally be necessary to install the VGA driver.
You can download both the manual and the installation guide here
http://www.asrock.com/mb/Intel/775i65G/?cat=Manual
And if "SCSI and RAID Host Controller" is still not shown in Device Manager, don't worry - because these functions are not supported by your motherboard (again assuming it is an Asrock 775i65G)
Thanks a lot,
First of all, when saying that I have multi-operationgs systems, I mean there are two operating systems installed on my PC(SP2, SP3) both are 32Bit. The first Windows SP2(NOT installed by me) has all multimedia audio card installed
well, and has SCSI and RAID Host Controller shown the device manager. However, only the VGA is not installed on Windows SP2. However, the second one Windows SP3(Installed by me) has VGA not installed, Multimedia audio NOT installed, and there is no SCSI and
RAID Host Controller in device manager.
First: Why did the CPUz, specy didn't detect motherboard name, and only detect the model. IF I need to open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on
the pcb somewhere, then what benfit would be there from hardware detection software?
Second: Yes, my motherboard has integrated video, and integrated audio card
However, this doesn't mean that I don't need to install them since the Vidoe controller is not properly installed (it is a default VGA ) Also, Multimedia audio controller is not functiong at all.
Finally: if And if "SCSI and RAID Host Controller" is still not shown in Device Manager in Windows XP SP3, because these functions are not supported by my motherboard, then why is 'SCSI and RAID Host
Controller' installed/shown in the device manger in Windows XP SP2 on the same PC???
A man should convert his anger and sadness into strength to continue living in this life.

What may be the reasons for my iphone switching off all of a sudden and how do i prevent it?

what may be the reasons for my iphone switching off all of a sudden and how do i prevent it?

With the home page on display, in the menus select View, then Zoom and then Reset
For details on the zoom features see [[page zoom]] and [[text zoom]]

HT5654 I often travel abroad and my host has changed Internet provider. Then my service was interrupted and I can't update iTunes. Any tips to stop the error messages?

I often travel abroad and my host has changed Internet provider. Then my service was interrupted and I can't update iTunes. Any tips to stop the error messages?

Wow! At least on Apple TV, problem solved. Apple: what's not to love? Please give me credit if you use it in marketing campaigns... ;-)

How to perform datalogging in a file using RT controller and a host PC?

I'm Using PXI-8145RT Controller and a Host PC(Dell Laptop),I used the TCP/IP DAQ Vi's but Im getting problems in logging data into a file at the Host using the Vi's .For 3 Channels the program works fine but as I increase the Number of Channels the program stops running on the RT Controller! Do we have to configure some TCP/IP settings for this or i have to use some other methods for datalogging into a file on the host using an RT Controller on the ethernet.

If you increase the number of channels and the RT program stops running, it could be that your scan rate is too fast for the increased number of channels on the 8145. First try to lower your scan rate by a large amount (a factor of 10, for example) to see if this is the problem. If you still see the same behavior when going above 3 channels of input, I would suggest looking at the following links for more information on communication with RT.
General Communication Info:
NI Developer Zone: Communicating with a Real-Time Engine
Specific Documents:
NI Developer Zone: Real-Time FIFO for Deterministic Data Transfer Between VIs
NI Developer Zone: TCP/IP between the Host PC and Real-Time Series Hardware
Furthermore, if you are using LabVIEW RT 7.0, I would highly suggest the use of the RT Communication Wizard. It will create the communication portion of your RT application for you.

HT1725 trying to connect and getting host down check your connection and try again??

trying to connect and getting host down check your connection and try again??

GymnastGirl152 wrote:
Whenever I try to text ...
Remember, your iPad is not a cellular telephone. It cannot do texting in the way a cellular telephone can - using SMS over a cellular network. All it can do is iMessage - meaning it would use WiFi to communicate to another Apple device.

Changing ip of physical and logical host

I have a 2 nodes Sun cluster 2.2 working. I have to put it in another lan, so I have to change both Physical and logical host and terminal concentrator and console ip addresses. How can I do?
Thanks

I don't see a reply so I'll take a shot. Just like you have 0-9 for numbers and you can arrange them anyway you want, you still only have 0-9. You have the physical (system block and datafiles) which are somewhat static. Then you have the the logical (tablespace, segements, extents)which are volatile and connected by chaining (links) which may be all over the place in the physical but appears to be one whole unit in the logical. Just like an image on a TV screen wearing a red hat, you see a red hat (logical) but it is actual pixels which are chained or linked (data pointers) to each other by the color red. I hope that helps until someone comes by with a better answer.

Smtp and pop3 host and port name of gmail server?????

can any body give me smtp and pop3 host and port name of gmail server?????to send a mail......

Just do a new initial context and lookup the datasource, in case you need other info like host name and port you can use MBEans like:
          InitialContext ctx = null;
               // fetch managed server name by accessing the
               // RuntimeServerMBean using the
               // MBeanServer interface
               ctx = new InitialContext();
               MBeanServer server = (MBeanServer) ctx
                         .lookup("java:comp/env/jmx/runtime");
               ObjectName service = new ObjectName(
                         "com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean");
               managedServerName = (String) server.getAttribute(service,
                         "ServerName");

HT201442 I am got error while trying to restore,, but i just only error file with 3194. I try many step by install lastest version and fix host file, but still fail. Anybody can give me any key point to solve this problem? Thank you

I am got error while trying to restore,, but i just only error file with 3194. I try many step by install lastest version and fix host file, but still fail. Anybody can give me any key point to solve this problem? Thank you

Error 3194:
This device isn't eligible for the requested build
It means that Apple has stopped signing the version of iOS that you have, try downloading the latest iOS version, then try Restore again.

DHCP Reservation Sync and DNS Host record sync etc shown in IPAM GUI

Hello all,
I am aware of the scripts in the TechNet script center to sync DHCP leases etc to IPAM, however my question is about something else -
If you highlight an IP address (IP address inventory->select an IP), You can see fields that say: "DHCP reservation sync", "DNS PTR record sync" and "DNS host record sync" as below:
I was curious as to what these are for. Is there some built-in sync functionality for these that I perhaps have not enabled? (Don't see such options any where..)
thanks,
-Ravi

Hi Ravi ,
The three columns tell us the information of the synchronization between IPAM server and DNS server (or DHCP server) .
Here is the detailed guide for using IPAM :
Using the IPAM Client Console :
https://technet.microsoft.com/en-us/library/jj878351.aspx#inventory
IPAM can sync DNS and DHCP records .
The IPAM database is separate from DHCP and DNS servers on our network ,and full synchronization of hosts and IP addresses between IPAM and managed DNS or DHCP servers does not occur automatically
unless we have configured automated tasks to perform this synchronization .
For detailed information ,see
DNS and DHCP record synchronization chapter in the following link :
Multi-server Management :
https://technet.microsoft.com/en-us/library/jj878329.aspx
Best Regards,
Leo
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

How to get the "host printer" and "destination host" as part of spad output

Hi ..
If i run the spad tcode and then i choose one printer, i see 4 folders: Device Attributes, Access Method, Output Attributes and Tray Info.
if i go to Devicess attributes i see: Device Type, Spool Server, Host, Device Class, Model, location , Message, lock printer in sap system.
If i go to Access Method i see the fields: Host Spool Access Method, Host Printer and Destination Host.
I am creating a report that needs the information mixed between the folder Device Type and Access Method folder
If i run spad tcode and enter "*" in Output devices i see only some of the fields i need but i need to see other fields that are contained into Access Method folder, this means, i need the complete report of all printers i have in my system with this fields:
Device Attribute - Output device (spad - entering "*")
Device Attribute - Spool Server (spad - entering "*")
Device Attribute - Location or message (spad - entering "*")
Device Attribute - Lock printer in SAP system (i do not see it if i run spad and choose all "*")
Access Method - Host Printer (i do not see it if i run spad and choose all "*")
Access Method - Destination Host (i do not see it if i run spad and choose all "*")
Access Method - Do not Query Host Spooler for Output Status. (i do not see it if i run spad and choose all "*")
Could you please le tme know how can i get the output of all the devices (printers) i have in my system with the above fields showed?
Thanks in advance.
Sapskystars.

As far as I can read you can find all that info in table TSP03D
Regards
Juan

Callmanager 4.3 and McAfee Host Intrustion Prevention

Similar Messages

Maybe you are looking for