Calls disconnect on first try but works on second

Some of my calls disconnects first time(receiver can't listen my voice)
But the second call connects.and works fine
I don't understand why ?any one help please
Topic edited by Rickard

Sorry to hear that.
As alexdon says, this sounds like it could be network related. Have you been in contact with your operator about this? Does it happen both on GSM only and WCDMA only? You can select this under Settings -> More -> Mobile networks -> network mode.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Similar Messages

Since i update my iPhone 5 with IOS 7.0.2, I start to have serious problems to call or receive calls from other telephones: is not possible to open the call at the first try. Somebody have the same problem?

Since i update my iPhone 5 with IOS 7.0.2, I start to have serious problems to call or receive calls from other telephones: is not possible to open the call at the first try. Somebody have the same problem?

Try
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data

Suspends fails the first time, but succeeds the second time

Hi all,
I am running Arch Linux on my Dell XPS 15 9530 laptop, and overall I am very happy with the combination. I have however had some issues with suspending.
The problem is that the first time I try to suspend the machine it seems to go to sleep, but then two seconds later it automatically wakes up again. If I then immediately try again to suspend, it works (it does not wake up automatically). Does anyone know what could be going on, and how this can be fixed?
Usually I suspend from my gnome 3 desktop, but I have also tried to suspend directly using 'systemctl suspend' without having an X server running, and the result is exactly the same. I have tried a few versions of the vanilla kernel, but also the linux-lts and the linux-ck images, but to no avail.
Here is the output from dmesg, where suspend fails:
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.543 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 334.544 msecs
PM: late suspend of devices complete after 0.201 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.944 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.424 msecs
PM: early resume of devices complete after 0.091 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
PM: resume of devices complete after 2769.054 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
and here where suspend succeeds:
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.412 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 780.265 msecs
PM: late suspend of devices complete after 0.387 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.988 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.411 msecs
PM: early resume of devices complete after 0.097 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
PM: resume of devices complete after 2801.389 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
systemd[1]: Requested transaction contradicts existing jobs: File exists
systemd[1]: Service sleep.target is not needed anymore. Stopping.
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
It seems to me like the only real difference has to do with the xhci_hcd errors, perhaps the following:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
Any input or help would be highly appreciated.

Rexilion wrote:Maybe you could confirm your suspicion by rmmoding xhci before suspend and modprobing it after resume?
Thanks for the response. I should have said so, but I had already tried that, but without any luck. It seems like it doesn't change anything.

Cant hear on first call but works on second call!

My wife and I both got Xperia Z1's at the start of November.
Recently my wife has been having a problem with her phone.
Nearly every time she calls me I cant hear her but she can hear me. If she hangs up and phones me back it works fine!
Anyone got any ideas why?

Its been happening for a few weeks now, only seems to be when she calls me although she doesnt really use the phone to call anybody else. We tried calling other numbers yesterday and it seemed ok and also worked ok when she called me! Maybe it has sorted itself out now

Page won't load on first try -- but stop then reload works

Several pages, most notably my.yahoo.com and worldofwar.net won't load on the first attempt. Eventually I get a timeout error. But while the load is trying, if I stop loading manually, then reload, the page finishes loading. It's then fine, until the next wake up after sleep, and it starts all over again.
I'm also noticing something similar with mail. When I send mail, it goes into the outgoing folder and I get an error that the message couldn't be sent. But if I exit mail and restart it, the pending message is sent without my having to do anything other than restart mail.
Any clues what to look for? This only began to happen after I moved. The only difference in my configuration is that I'm using a new DSL modem and dynamic IP address from my ISP now, where I was using a static address before with an older model modem.
I've checked the console logs, before/during/after observing the problem, and no new entries are made.
Thanks for any suggestions.
G5 PPC dual 2.7 Mac OS X (10.4.6)

Please post in the Boot Camp forum, thats where you will find the MS Windows and Boot Camp gurus. Note also it's Boot Camp, and not Bootcamp which is something you do when you enter the military.

I cant make phone calls and have a full network coverage. I can browse internet, receive sms, mms, mails but each call ends after first try! It doesnt even ring ! Help

I cant make any phone calls.
I have full network coverage, 3G access and internet. SMS + MMS + emails work.
I can receive phone calls and I have taken out the sim card and inserted it again.
Nothing works. What should I do ?

Nothing was wrong on their side. I have restored the phone. It is working now. Weird ...

Unhandled exception when code runs for the first time,but works fine the second

Hi All,
I have the following code snippet
private void RGL_Click(object sender, RibbonControlEventArgs e)
Word._Document oDoc;
oDoc = Globals.ThisAddIn.Application.ActiveDocument;
object start = oDoc.Content.Start;
object end = oDoc.Content.End;
oDoc.Range(ref start, ref end).LanguageID = WdLanguageID.wdEnglishCanadian;
oDoc.Range(ref start, ref end).NoProofing = 0;
Microsoft.Office.Interop.Word.ReadabilityStatistic DocStats;
DocStats = oDoc.ReadabilityStatistics[10];------>exception occurs here when code runs first time
MessageBox.Show(DocStats.Name + " " + DocStats.Value);
When I copy paste a document and click on the button it raises a COM exception but if I click continue and click on the button again, the correct grade level score is displayed.Cant figure out why this is happening.

Thanks for the answer Eugene, this exception never shows up if I type something and click on the rgl button , but if i open a huge document that is already in Canadian english and click on this ribbon it gives me the following exception
System.Runtime.InteropServices.COMException was unhandled by user code
HelpLink=wdmain11.chm#36966
HResult=-2146824090
Message=Command failed
Source=Microsoft Word
ErrorCode=-2146824090
StackTrace:
at Microsoft.Office.Interop.Word.ReadabilityStatistics.get_Item(Object& Index)
at UsabilityMapping_V01.Ribbon1.RGL_Click(Object sender, RibbonControlEventArgs e) in <my path> 1211
at Microsoft.Office.Tools.Ribbon.RibbonPropertyStorage.ControlActionRaise(IRibbonControl control)
at Microsoft.Office.Tools.Ribbon.RibbonPropertyStorage.ButtonClickCallback(RibbonComponentImpl component, Object[] args)
at Microsoft.Office.Tools.Ribbon.RibbonManagerImpl.Invoke(RibbonComponentCallback callback, Object[] args)
at Microsoft.Office.Tools.Ribbon.RibbonMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture)
at Microsoft.Office.Tools.Ribbon.RibbonManagerImpl.System.Reflection.IReflect.InvokeMember(String name, BindingFlags invokeAttr, Binder binder, Object target, Object[] args, ParameterModifier[] modifiers, CultureInfo culture, String[]
namedParameters)
InnerException:

Dual-track audio after export plays on first clip, but not on second?

So, I've been working on a project with video that has two audio tracks, and they play fine in the preview window in premiere, but as soon as I export them, the first clip of it works, but the second clip I have does not have the second audio track, just the first. If anyone could shed some light on whats going on that would be great. Also, I tried using media encoder, in which I couldn't hear either of the audio tracks.

Hi incinirate,
So, I've been working on a project with video that has two audio tracks, and they play fine in the preview window in premiere, but as soon as I export them, the first clip of it works, but the second clip I have does not have the second audio track, just the first. If anyone could shed some light on whats going on that would be great. Also, I tried using media encoder, in which I couldn't hear either of the audio tracks.
That's rather strange. Sorry to hear that.
Where did these files originate? From a video camera, screen capture, webcam, or mobile device? What is the format of these files? More details on your system, OS, version of Premiere Pro, etc., please.
Thanks,
Kevin

Workspace page doesn't render on the first attempt, but on the second

We have a clustered environment where users log into the Big IP load balancer. Local users are able to access the Workspace URL without a problem from within the company. Users out of state and out of the country are not able to connect successfully on the first attempt about 85% of the time, but are able to on the second attempt after killing their browser session. Their session just hangs without rendering the login screen on the first attempt. They are usually able to log in without a problem the rest of that day. We have performed some tests and asked a few users to bypass the load balancer and hit the servers directly, and they have a better success rate of receiving the log in screen.
I am a local user and this is also an issue when trying to connect remotely to the Workspace page. It eventually times out and I receive the following message:
"_execScript::Error loading file './js/com/hyperion/bpm/web/common/format/Format.js' Error The operation was timed out".
Has anyone ever experienced this issue? I would appreciate any suggestions. Thanks!

Hello L Swarz,
Thank you for the details of the issue you are experiencing when downloading your purchased song to your iPod nano.
I am not sure if you have tried these specific steps, but I recommend downloading the purchased song to iTunes on your computer using the steps in the following article:
iTunes 11 for Windows: Download previous purchases from the iTunes Store
http://support.apple.com/kb/PH12491
Thank you for using Apple Support Communities.
Best,
Sheila M.

Word, pdf, iPhoto email, don't work on one user account but work on second user account

I have MacBook Pro running 10.7. In my main user account I've recently had major issues with several applications. Word quits on startup, pdf files quit on startup, the latest iPhoto application quits when attemping to send email with photos from iPhoto.
I set up a second user account and all the issues went away. Can anyone explain why such bugs are present in one user account by not the more recent one?
Thanks

In your wife's account:
Try trash the com.apple.iPhoto.plist file from the HD/Users/ Your Name / library / preferences folder. (Remember you'll need to reset your User options afterwards. These include minor settings like the window colour and so on. Note: If you've moved your library you'll need to point iPhoto at it again.)
*What's the plist file?*
For new users: Every application on your Mac has an accompanying plist file. It records certain User choices. For instance, in your favourite Word Processor it remembers your choice of Default Font, on your Web Browser is remembers things like your choice of Home Page. It even recalls what windows you had open last if your app allows you to pick up from where you left off last. The iPhoto plist file remembers things like the location of the Library, your choice of background colour, whether you are running a Referenced or Managed Library, what preferences you have for autosplitting events and so on. Trashing the plist file forces the app to generate a new one on the next launch, and this restores things to the Factory Defaults. Hence, if you've changed any of these things you'll need to reset them. If you haven't, then no bother. Trashing the plist file is Mac troubleshooting 101.
Regards
TD

Mac Pro never boots first try

Just bought a refurbished Mac Pro and it never boots the first try, (always on the second try,) if it's been turned off for awhile. It clicks and spins a couple times, but no chime and no display. So I hold the power button until it shuts off, then it will boot normally the second attempt.
Another clue, although audio is set to the sound card, the chime is through the onboard speaker when it does boot first time. It seems like the config is lost until power can be applied. Is there a battery power to the mother board missing possibly?
Is this a known problem? Is there a fix? I read many similar complaints on the web. I have had so many problems getting this computer ordered, now it arrives and is broken, very bummed that Apple cannot get my order correct multiple times, then at last sends me a 'broken' computer
thanks
td

For all of you who may come accross this thread - I have a solution, even though the thread is a bit old.
I have a refurbished Mac Pro Early 2009 and it also never booted on the first try (identical to tduncan). I brought it to the Apple genius bar to get it fixed, they replaced the start button components. When I got home, the very same problems appeared. After several calls to Apple support (I had purchased the extended warranty) and a return to the Apple store again for repairs, the problem still was not resolved. I gave up and simply accepted that it was either the video card (NVIDIA GeForce GT 120 512 MB) as had been suggested in some help forums or still a problem with the start button. I started leaving the Mac Pro on all the time, and when I did turn it off, I knew that I would have to let it try to boot up, let it stall, then restart the process by turning off and turning on the Mac Pro again. Aside from this irritation, the Mac Pro runs really well, and I have upgraded it a lot over the past 2 years.
Long story short, I ended up keeping an old PC to play one of my favourite games (Mech Warrior 3 and 4) and one day, the PC started acting up. After a lot of frustration (which is why I left the Windows world), I ended up replacing the internal battery and everything was fine.
I came accross this thread yesterday, and the suggestion from Limnos about the weak PRAM battery reminded me of the old PC and how it ran perfectly after replacing the motherboard battery for the timer. Today, I purchased a new internal backup battery at a local Canadian Tire, swapped batteries and instantly, the problem was resolved. I have tested it several times today, and the pattern of "2 tries" to start is definetely broken
Funny though that the Genius bar didnt figure this - sometimes it's the little things that are overlooked! I am posting this just in case anyone else runs into a similar situation!
Cheers
Stu

I can import my first clip to the video library, but not the second clip. I tried dragging-dropping and using the "E" key, but only the first clip will show up in the library. I use IMovie 9.0.9 and OSX 10.8.5. with no problems until yesterday.

I can drag my first clip from the New Event window into the Project Library, but not the second. I can highlight the second clip in the New Event window, but it won't "drag". The "E" key works for the first clip, but not the second.I've been using IMovie daily and the problem just appeared. No upgrades to the computer and no new software installed. IMovie 9.0.9 and OSX 10.8.5

Thanks victoryhat. I learned some new things from this very clear tutorial. But it didn't answer my question about why the titles don't stay with the video when I export it.
He did mention something that might be a clue however. When he talked about importing a title he created as an image, he noted that he was careful to make the image the same size as the video he was adding it to: 1280 x 720. Since I took the video with an iPhone in the vertical position, my video image isn't the same size and orientation as the titles.
Maybe there is a way I should be setting the screen for this size??? I'll go back and play around. Meanwhile thanks for alerting me to Gary Rosenzweig's MacMost tutorials. Very clear. I'll look for more.

HT203712 I have a 2011 tahoe. My bluetooth functioned properly until I updated my iPhone. Now the iPhone connects to the Tahoe but when I try to call a number it does not work. Either it cals the number and has no outgoing or incoming sound or it just

I have a 2011 tahoe. My bluetooth functioned properly until I updated my iPhone. Now the iPhone connects to the Tahoe but when I try to call a number it does not work. Either it cals the number and has no outgoing or incoming sound or it just says it iis unable to complete the call.

I would check with the Auto dealer where the vehicle was purchased to check and see when the bluetooth software was last updated on your vehicle. With the vehicle being a 2011 and if the software has not been updated since the dropping of IOS 7 then obviously there will be software incompatibilities.
Good luck.

PDF Embed only works on the first try

Hi everyone,
i've finally got it. The PDF Embed worked on my Reports Server.
But a strange thing is happening.
When I start the Reports Server and run the report for the first time everything works just fine, but when I try to run the report again i receive the following error:
REP-1923: PDF Font Embed error
The report doesn't works again until I stop and restart the Reports Server. And again after i run the report for the first time it doesn't works anymore until new restart.
I'm using Oracle 9iAS (9.0.2.1) with 2703110 and 2842923 patches installed.
The system is Red Hat Linux 7.3.
The uifont.ali file:
#===============================================================
[ Global ] # Put mappings for all surfaces here.
# Mapping from MS Windows
Arial = helvetica
"Courier New" = courier
"Times New Roman" = times
Modern = helvetica
"MS Sans Serif" = helvetica
"MS Serif" = times
"Small Fonts" = helvetica
[ PDF:Embed ]
# This example shows how to embed Type 1 helvetica font into the PDF file:
# helvetica = "helvetica.afm helvetica.pfa"
# You need to specify the .afm file before the .pfa file.
# The font files must exist in one of the folders specified in REPORTS_PATH.
helvetica = "I2501P.afm I2501P.pfa"
The Font I'm using is I2501P (a bar code font).
The I2501P.afm I2501P.pfa files are located in $ORACLE_HOME/reports/samples/demo. This directory is on $REPORTS_PATH.
The reports is being called by this URL:
http://caarjrep.caarj.com.br:7778/reports/rwservlet?server=repserver+module=TEST.RDF+destype=cache+desformat=pdf+delimiter=tab+userid=scott/tiger@iasdb
Anybody can help??
Thank you all.
Marcus Oliveira ([email protected])

Hi Marcus
I faced the same problem. I understand from Oracle that this has been fixed and will be available in the next patch whenever it becomes available.
Regards
Sripathy

Urgent: PDF Embed only works on the first try

Hi everyone,
i've finally got it. The PDF Embed worked on my Reports Server.
But a strange thing is happening.
When I start the Reports Server and run the report for the first time everything works just fine, but when I try to run the report again i receive the following error:
REP-1923: PDF Font Embed error
The report doesn't works again until I stop and restart the Reports Server. And again after i run the report for the first time it doesn't works anymore until new restart.
I'm using Oracle 9iAS (9.0.2.1) with 2703110 and 2842923 patches installed.
The system is Red Hat Linux 7.3.
The uifont.ali file:
#===============================================================
[ Global ] # Put mappings for all surfaces here.
# Mapping from MS Windows
Arial = helvetica
"Courier New" = courier
"Times New Roman" = times
Modern = helvetica
"MS Sans Serif" = helvetica
"MS Serif" = times
"Small Fonts" = helvetica
[ PDF:Embed ]
# This example shows how to embed Type 1 helvetica font into the PDF file:
# helvetica = "helvetica.afm helvetica.pfa"
# You need to specify the .afm file before the .pfa file.
# The font files must exist in one of the folders specified in REPORTS_PATH.
helvetica = "I2501P.afm I2501P.pfa"
The Font I'm using is I2501P (a bar code font).
The I2501P.afm I2501P.pfa files are located in $ORACLE_HOME/reports/samples/demo. This directory is on $REPORTS_PATH.
The reports is being called by this URL:
http://caarjrep.caarj.com.br:7778/reports/rwservlet?server=repserver+module=TEST.RDF+destype=cache+desformat=pdf+delimiter=tab+userid=scott/tiger@iasdb
Anybody can help??
Thank you all.
Marcus Oliveira ([email protected])

Hi Marcus
I faced the same problem. I understand from Oracle that this has been fixed and will be available in the next patch whenever it becomes available.
Regards
Sripathy

Calls disconnect on first try but works on second

Similar Messages

Maybe you are looking for