Calls getting dropped

Hi,
My scenario is like this:
IP Phone ---> Call Manager---->h323 gateway--->Avaya -----> Avaya phone.
I have created two device pools, DP-1 and DP-2 and assigned separate regions to these Device Pools. The codec between these regions has been configured as G.729. One hardware transcoder has also been created in the router and assigned to a MRGL which both DP's are using. IP Phone has been assigned to DP-1, and H.323 gateway has been assigned to DP-2. So the calls through this gateway to Avaya will be G.729 codec. Avaya has been configured to make the calls to the H323 gateway as G.729.
Whenever I am making a call to Avaya, I am able to get the ring from Avaya, when the receiver is picked up I am not able to hear anything. This is same when both side makes a call.
The IP reachability is there between all the devices. I have tried making the MTP required checked and unchecked under the gateway configuration, but the same result.
In the debug voip ccapi inout I am getting an error which is attached herewith.
The error code mentioned is 47 which is no resource. I have also checked by changing the codec values on both the ends.
Can anyone tell what could be the problem?
Thanks,
Manu

Disconnect Cause=47 is indicating issue is media negotiating like Transcoder, MTP & Codec negotiation.
Crosscheck the incoming & outgoing dial-peers for matching codec & voice class codec configurations. saw outbound dial-peer 40 matched but no logs to show matching inbound dial-peer.
CUCM has an option for "Wait for far end H245 TCS" on CUCM which is checked by default. Try to uncheck it and test the behaviour please.
Please collect detailed ccm traces & debug voice ccapi inout, debug h225 asn1 & debug h245 asn1.
what is the connection type from GW to PBX? PRI or IP connection? Please post your GW config also.
Please rate all the useful posts

Similar Messages

  • HT201436 call gets dropped too many times ,network is alright

    call gets dropped too many times ,network is alright

    It is also relatively easily to dial 911 during the palm reset process as well.  Maybe a confirmation screen would be nice.

  • UCCX 7 Call gets dropped once agent picks up

    I have been troubleshooting a problem for a few weeks now where calls are being dropped as soon as the agent picks up the call. This is happening to various agents happening a few times per day everyday. I have done a reactive debug on the script and it seems to go through to the end ok yet everytime an agent reports a call drop as soon as they pickup, i see the following in the MIVR logs. I have checked the CSS/Partitions of all the CTI ports also.The CCM traces and Q931 traces show normal call clearing:
    215269973: Apr 21 14:53:42.306 GMT %MIVR-APP_MGR-7-STEP_FAILURE:Failure to execute a step: Application=App[name=switchboard,type=Cisco Script Application,id=50,desc=switchboard,enabled=true,max=10,valid=true,cfg=[ApplicationConfig[schema=ApplicationConfig,time=Wed Jan 06 16:44:49 GMT 2010,recordId=67,desc=switchboard,name=switchboard,type=Cisco Script Application,id=50,enabled=true,sessions=10,script=SCRIPT[Switchboard.aef],defaultScript=,vars=null,defaultVars=null]]],Task id=30000147369,Step id=198,Step Class=com.cisco.wf.steps.ivr.TerminateStep,Step Description=Terminate (--Triggering Contact--),Exception=com.cisco.contact.ContactInactiveException: Contact id: 32425, Contact is inactive when getting channel
    215373932: Apr 21 15:03:50.012 GMT %MIVR-LIB_EVENT-3-DISPATCH_FAILURE:A failure occured while dispatching an event: Event=com.cisco.call.CallEvent[CALL_ANSWERED,state=CALL_ANSWERED,contactImplId=3672150/2,lastContactImplId=3672150/2,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],lastSession=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],contactSeqNum=0,lastContactSeqNum=0] on CallContact[id=32462,type=Cisco Agent Call,implId=3672150/2,active=true,state=CALL_ANSWERED,inbound=false,handled=false,locale=en_US,aborting=false,app=null,task=null,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],seqNum=0,time=1271858629996,cn=null,dn=null,cgn=6664,ani=null,dnis=null,clid=null,atype=UNKNOWN,lrd=null,ocn=null,odn=null,uui=null,aniii=null,ced=null] at Wed Apr 21 15:03:50 BST 2010,Event source=CallContact[id=32462,type=Cisco Agent Call,implId=3672150/2,active=true,state=CALL_ANSWERED,inbound=false,handled=false,locale=en_US,aborting=false,app=null,task=null,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],seqNum=0,time=1271858629996,cn=null,dn=null,cgn=6664,ani=null,dnis=null,clid=null,atype=UNKNOWN,lrd=null,ocn=null,odn=null,uui=null,aniii=null,ced=null],Event listener=com.cisco.wf.subsystems.rmcm.ICDContactAdapter@50add0,Exception=java.lang.ClassCastException: java.lang.Integer
    215375195: Apr 21 15:03:55.715 GMT %MIVR-APP_MGR-7-STEP_FAILURE:Failure to execute a step: Application=App[name=switchboard,type=Cisco Script Application,id=50,desc=switchboard,enabled=true,max=10,valid=true,cfg=[ApplicationConfig[schema=ApplicationConfig,time=Wed Jan 06 16:44:49 GMT 2010,recordId=67,desc=switchboard,name=switchboard,type=Cisco Script Application,id=50,enabled=true,sessions=10,script=SCRIPT[Switchboard.aef],defaultScript=,vars=null,defaultVars=null]]],Task id=30000147532,Step id=208,Step Class=com.cisco.wf.steps.ivr.OutputStep,Step Description=Play Prompt (--Triggering Contact--, WelcomePrompt),Exception=com.cisco.contact.ContactInactiveException: Contact id: 32461, Channel id: 52, Contact is in Terminated/Connected state
    I do not have experience with scripting so if anyone could point me in the right direction that would be appreciated,cheers.

    Reviewing the  MIVR logs you provide I'm not sure which call your talking about. I see 2 calls with exception messages in the time stamp your saying.
    First call:
    Apr 22 11:49:11.621 GMT %MIVR-SS_TEL-7-UNK:CallID:33466 MediaId:3673987/2 Task:30000153869 com.cisco.jtapi.CiscoRTPInputStoppedEvImpl received
    However this call is dropped as per the Jtapi message that the disconnect came from the CCM side however I can see that this call was never assigned to an agent so there should be no miss calls.
    As for the second call, I don't have the full picture, as we don't have the offered message of when the call arrives to the system.
    Here is a break down of the other call.
    Call transferring to assigned agent:
    Apr 22 11:49:07.308 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: CallCtlConnInitiatedEv received for call 37228421 [3673989/2] and agent AylwardM
    System changed call/agent states to answered/talking
    Apr 22 11:49:07.308 GMT %MIVR-SS_CM-7-UNK:AgentCallContact 33468 and implId 3673989/2 moved to Answered state
    We now see the exception message:
    Apr 22 11:49:07.308 GMT %MIVR-LIB_EVENT-3-DISPATCH_FAILURE:A failure occured while dispatching an event: Event=com.cisco.call.CallEvent
    However if you look futher down the call is connected to the agent successfully and in a talking state.
    221901300: Apr 22 11:49:15.387 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver.callChangedEvent():
    CallCtlConnEstablishedEv 3673989/2
    Unknown event3673989/2
    221901301: Apr 22 11:49:15.387 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: CallCtlConnEstablishedEv received for call:37228421 [3673989/2], address 6656, calling party 6656, and called party 01923821368
    Call Dropped as it recieve a disconnect event.
    221902844: Apr 22 11:49:24.621 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: TermConnDroppedEv received for call 37228421 [3673989/2] and agent AylwardM
    The problem with the above call is that you don't see the CallCtlConnEstablishedEv till 7 seconds later, which is why I suspect you get the exception error, as it never got confirmation the call was delivered.
    So my concern here, is if you stated you had a issue with calls getting dropped on the UCCX I would agree and ask you to provide CCM/Jtapi logs from the UCCX.
    However you stated that your agents are getting miss calls on their IP phone, I disagree with this point as per the analysis performed.
    "One question, when the CTI port is ringing the agent's phone to then transfer (reserved state) that call to that agent and the caller hangs up before the agent answer it, does the agent will hear a fast busy tone because that is what the CTI port transfer at the end to the agent? Am I right? if this is it I think there is no way to control this from the UCCX perspective, right?
    Gabriel"
    This senario will never happen, as the call would be terminated the moment the other party drops.

  • After 4 or 5 rings the call gets dropped instead of going to voicemail.

    I recently upgraded to callmanager 7.1 and now whenever anyone calls our main number, if we do not anwser it within 4 or 5 rings it will drop the call, instead of going to voicemail.
    Please help and thanks
    George

    Hello George.
    Since you have upgraded, I'm assuming that CFw was working before.
    Have you checked the CSS in the Forwarding section of the line?
    Also try calling the same number internally and let it forward to voice mail. Does it have same symptom? Even if it fails, by any chance do you see the number on the calling phone changed to Voice mail pilot number at all?
    Thanks
    - abu

  • My mac book pro keeps dropping calls when skyping.  I skype regularly with one person and they told me that more calls get dropped with me than with anyone else.

    When skyping, my mac book pro keeps dropping calls.  Apparently, it's the worst with my computer according to those I skype with.  Please help!

    What did Skype support say when you asked them about this?

  • Video Call Quality drops / starts out really bad

    Quality of video calling is sub-standard, I live in the UK and use Skype everyday to call a friend in the Philippines and our calls constantly drop out, and at times won't even connect. When connected video quality frequently is pixelated and at times freezes before dropping calls, on average I would say that I get about 10-12 call drop-outs per day and it's not acceptable. Both me and my friend's wi-fi signal are strong, yet everytime a call drops we get a message saying internet signal too weak, it's not the internet as Viber works perfectly well between us and our wi-fi signals are at maximum strength, it's Skype's signal too weak and no matter how many times I've left feedback complaining about this (at least 100 complaints over 10 months), nothing is done to ensure that me and my friend can have a conversation without call drop outs and pixelated and frozen screens. I'm sure that I'm not the only person in the world trying to have a video call with someone on the other side of the world, and also sure that I'm not the only person suffering from this sub-standard service, so it's time you did something to improve the quality of your service and make it possible for me to be able to talk to my friend. You advertise free worldwide Skype-to-Skype video calls, but don't provide the service because of sub-standard signal from Skype, I call that false advertising, so address this issue as it is becoming a real problem for me and my friend.

    I have Skype video calls with my friend nearly 6,000 miles away in South Korea.  I have video conversations all the time.  My last video call a few days ago was 5 hours long with no issues.  You can't compare to different services equally since they operate differently.  If you are getting drop-outs then there is something limiting it and can be hardware or software based.  Skype functions best when multiple connections can be handled by your wired or wireless router simultaneously and UDP is not impeded.  If your equipments gets overloaded or is blocking traffic then the quality of your call or Internet connection stability can deprecate to the point where your call gets dropped.
    To try to narrow the problem down:
    1.  You should try wired instead of wireless.
    2.  If you can bypass the routers used and connect directly, try that as well.
    3.  If the routers being used have any firmware upgrades, be sure to upgrade to the latest.
    4.  Try with uPnP enabled/disabled in your routers or in Skype to see if that helps.
    Usually routers that claim to work well with T0rrents work best with Skype because their firmware handles uPnP and multiple connections without crashing, halting. or failing in some manner.
    My friend in South Korea has moved several times in the past few years.  Many times I've had to remote into his system to repair the conditions of the Internet connection in the location he was staying.  At one point there was a community router being used on the floor he was staying on that was problematic.  I remoted into the unprotected Korean router and updated the firmware that was known to have uPnP issues.  After the firmware update the dropouts we were experiencing once ever 5-20 minutes disappeared and the connection was rock solid and continued to work flawlessly for the 6 months he stayed there.

  • When I make an international call, calls get dropp...

    My skype is not working . When I make a call international .....calls get dropped. Please advice. Thanks.
    Subject/title amended to reflect post content.

    It is not an international call. FaceTime is done over wifi (the Internet), not the phone. Now you may need to first call the other party to make sure they are connected to wifi, but you could always use email to prearrange a time for the call so you would each know to be on a wifi network at the appointed time.

  • After 2.1 update still getting dropped calls

    After 2.1 update I have dropped at least 15 Phone calls , the signal strength is usually on 5 bars 3g , the calls drop without warning (doesnt break up or destort voice), It also seems if I look at email while on a call it drops the call about 20 seconds later, another odd thing is the improved reception at my desk at work , used to get 1 bar on EDGE or no service , after 2.1 update I got 5 bars on 3g and the internet was pretty fast in the same spot but only during the morning time , I went back into the office about an hour later the bars dropped to 1 bar on EDGE/no service and the internet wouldnt even work , and now today when talking with my girlfriend (who has the same phone) the call quality has dropped , the speech sounds like she or I are talking through a voice changer where the words become incomprehensible or the sound totally drops momentarily and then returns to normal , so now im finding myself asking are you there over and over , do you think this phone will ever exhibit excellent voice quality and call reliablity or should I just go back to my old company?

    Since updating my phone to the new 2.1 Firmware I have been seeing my phone at full bars which I normally don't see on a regulars bases like I do now but if I am having full bars why am I having connectivity issues like when I am talking on the phone it is constantly breaking up almost to the point it sounds like a blown speaker and when I send a SMS it pauses at the end of the loading box for about a minutes before the messages is completely sent. These 2 issues I have never experienced until right after the install of the new 2.1 Firmware

  • No point of using Skype.. calls are getting drop f...

    No point of using Skype.. calls are getting drop frequently..
    I have waisted time and money too here.
    My calls are getting dropped again and again.. now i am thinking how to finish available balance.
    anybody can suggest me how to use my rest money because calling someone is not worth.

    Please,  run the DirectX diagnostics tool. Go to Windows Start  and in the Run box type dxdiag.exe and press the OK button. This will start the DirectX diagnostics program. Run this diagnostics and save the results to a file. Please, attach this file to your post. Be aware that you will have to zip this file before attaching it here.

  • AD HOC Conferencing. Customer gets dropped when Agent leaves call.

    We have the conferencing setup so that the conference only ends when Onnet agents leave the conference.  For some reason an agent conferences in a supervisor and then leaves the call which then drops the customer.  It is not with every call.  DSP resources are hardware and very plentiful.  The phones being used are 7942's.  The BiB is turned on and no MRGL are associated to the phone level.  I am not sure why a customer is getting dropped.. RTMT shows plenty of DSP resources and CM has the correct service parameter.  Can anybody lead me the right way?

    So I think this has to do with CVP warm transfers.  The script has network transfer set to 0 and a send to vru node in it.  This is clearly a signalling problem.  Probably going to have to start a TAC case.

  • Why am I suddenly getting dropped phone calls

    I've had my iPhone 4 since June of 2010 and have been completely happy with it.  Then suddenly last week I started experiencing dropped calls--especially dropped long distance calls.  I make the call, we'll be chatting for 10 minutes or so, then suddenly the person I called can't hear me anymore.  I can hear them, but they can't hear me.  Within a matter of 30 seconds the line goes dead.  If I try to phone back, I can hear them when they answer their phone, but they can't hear me at all.  It's maddening.  I don't know if it's a problem with my phone, with AT&T or both. 
    Anyone with a clue?
    Debby J

    Go to setting and reset networks setting. If that doesn't work call your carrier to reset setting. Last thing you can change your sim card. After that go to Apple and they have a special software to check your drop calls on your phone. If it hardware they will replace your iPhone.

  • When i am logging/ Capturing my mac is telling me that i am getting dropped frames. would i need to get a LaCie Hard Drive?

    When i am logging/ Capturing my mac is telling me that i am getting dropped frames. would i need to get a LaCie Hard Drive?

    To be honest, I've had 2 Lacie drives crash out of 2 bought.  That's not a good track record for me.
    Your best bet  (I'm a computer professional, for what it's worth):
    Get a hard drive case or enclosure that supports firewire 800 and put your own PC hard drive (SATA for example) 7200rpm or higher hard drive into it.
    Let me explain a bit more.  External hard drive manufacturers often put no-name hard drives into fancy cases to cut costs and that's how they make a profit.  I've have had nothing but problems with with these types of drives. (Like Lacie) You are much better off getting some type of decent drive enclosure and getting your own GOOD hard drive.  I would highly recommend Seagate, I have NEVER had a problem with a Seagate drive in 20 years of owning PCs and Macs.  Western Digital is also a good brand (though I had 1 crash). These are the types of drives you would put in your Mac Pro.  You want to get an SATA hard drive.
    I have owned several external cases where the case electronics fried, but the hard drives were still in good shape. Take the hard drive out, put it into a new case you're good to go!
    For video you want to make sure that your hard drive case supports Firewire 800!  This is mandatory.
    My personal favorite, (and I own 5 of these) is Vantec's NexStar hard drive enclosure.  They accept any SATA 3.5" drive (I bought mine from a company called ComputerStop).  I have yet to have a single problem with any of them.  They are solid aluminum casing, you can literally throw them into your backback, drop them on the floor and your hard drive is fairly well protected from impact damage (at least you won't break the case with anything short of a sledgehammer).  I am currently looking at getting a second one of these:
    http://www.vantecusa.com/gl/product/view_detail/173
    (My bad, this is an IDE case up to 750GB)
    This the one you want:
    http://www.vantecusa.com/gl/product/view_detail/354
    As far as the hard drive, you can get a Seagate Baracuda drive 1TB at 7200rpm drive for about $60.  The case and hard drive together, maybe a few over $100 for the whole thing.  With shipping, and tax figure about $150.
    Don't let the price fool you.  It will rock.
    Story: I got an iOmega "raid" case with two Seagate drives in it and the iOemga case fried, but the hard drives were still good. Fortunately, they were in two removable trays.  I put them into two "rocketfish" hard drive cases almost 3 years ago and I am still using them every day today. 
    Moral of this story:  It's the quality of the hard drive that matters, not what case it's in.
    Is it hard to set up?
    Not at all.  You put the hard drive into a tray, (with Vantec case), screw it in.  It only goes in 1 way.  Plug in a power cable to the drive.  Slide the tray into the case (carefully, don't munch the power cable!) and screw it in place. You can literally do it in 10 minutes or less.  There are, of course instructions, but if you are reasonably clever, you can literally see what plugs into what just by looking at it.
    Sorry for the long reply, but I have a lot of experience with external drives and I hope this helps others.
    Finally, when you make it to the big time you can spend $400, get yourself a firewire RAID enclosure and you can upgrade to 4 external hard drives in 1 enclosure.  Figure $800 for that set up, but you can go up to 12 TB of drive space with that, or up to 3TB if you are running redundant discs.  But that's a whole other ballgame...
    Peace.

  • WLC 5508, SW 6.0.199.4, 1142 AP: Clients getting dropped intermittently

    We have deployed a WLC 5508 w/ SW version 6.0.199.4, 1142 AP's & open authentication w/ MAC filtering. Clients are randomly getting dropped with "Limited Access" shown in Win 7. In this state, the client machine is unable to ping the gateway and sometimes lose their DHCP assigned IP as well. A manual disconnect/re-connect to the SSID is required everytime.
    I ran a debug on one the clients stuck in the "Limited Access" state (debug client xx:xx:xx:xx):
    *Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Adding mobile on LWAPP AP 3c:ce:73:c5:1e:b0(0)
    *Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 23) in 5 seconds
    *Apr 15 16:59:23.205: e0:91:53:60:1f:e4 apfProcessProbeReq (apf_80211.c:4722) Changing state for mobile e0:91:53:60:1f:e4 on AP 3c:ce:73:c5:1e:b0 from Idle to Probe
    *Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 15 16:59:28.553: e0:91:53:60:1f:e4 apfMsExpireCallback (apf_ms.c:418) Expiring Mobile!
    *Apr 15 16:59:28.554: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [3c:ce:73:c5:1e:b0]
    *Apr 15 16:59:28.554: e0:91:53:60:1f:e4 Deleting mobile on AP 3c:ce:73:c5:1e:b0(0)
    On doing a manual re-connect, got the following logs:
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Association received from mobile on AP b8:62:1f:e9:9f:30
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific IPv6 override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying IPv6 Interface Policy for station e0:91:53:60:1f:e4 - vlan 15, interface id 14, interface 'students'
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1276)
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [b8:62:1f:e5:6a:90]
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Updated location for station old AP b8:62:1f:e5:6a:90-0, new AP b8:62:1f:e9:9f:30-0
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfProcessAssocReq (apf_80211.c:4268) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Probe to AAA Pending
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 20) in 10 seconds
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Initializing policy
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP b8:62:1f:e9:9f:30 vapId 7 apVapId 2
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfPemAddUser2 (apf_policy.c:213) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from AAA Pending to Associated
    *Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station:  (callerId: 49) in 65535 seconds
    *Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Including FT Mobility Domain IE (length 5) in Initial assoc Resp to mobile
    *Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Sending Assoc Response to station on BSSID b8:62:1f:e9:9f:30 (status 0) Vap Id 2 Slot 0
    *Apr 15 17:01:38.145: e0:91:53:60:1f:e4 apfProcessRadiusAssocResp (apf_80211.c:1957) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Associated to Associated
    *Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
    *Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *Apr 15 17:01:39.953: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4166, Adding TMP rule
    *Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
      ACL Id = 255, Jumbo F
    *Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
    *Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *Apr 15 17:01:39.954: e0:91:53:60:1f:e4 Sent an XID frame
    *Apr 15 17:01:40.807: e0:91:53:60:1f:e4 Orphan Packet from STA - IP 169.254.201.128
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP DISCOVER (1)
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP OFFER (2)
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
    *Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.6.2.160
    *Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP   server id: 10.6.15.254  rcvd server id: 10.6.15.254
    *Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
    *Apr 15 17:01:43.240: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 316, port 13, encap 0xec03)
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP REQUEST (3)
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   requested ip: 10.6.2.160
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   server id: 10.6.15.254  rcvd server id: 10.6.15.254
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.6.2.160
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP   server id: 10.6.15.254  rcvd server id: 10.6.15.254
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Reached PLUMBFASTPATH: from line 4972
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
      ACL Id = 255, Jumbo Frames = NO,
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Assigning Address 10.6.2.160 to mobile
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 Added NPU entry of type 1, dtlFlags 0x0
    *Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Sending a gratuitous ARP for 10.6.2.160, VLAN Id 15
    *Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
    *Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP processing DHCP INFORM (8)
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   ciaddr: 10.6.2.160,  yiaddr: 0.0.0.0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   chaddr: e0:91:53:60:1f:e4
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   ciaddr: 10.6.2.160,  yiaddr: 0.0.0.0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP   server id: 10.6.15.254  rcvd server id: 10.6.15.254
    show client e0:91:53:60:1f:e4 (after re-connect)
    (Cisco Controller) >show client detail e0:91:53:60:1f:e4
    Client MAC Address............................... e0:91:53:60:1f:e4
    Client Username ................................. N/A
    AP MAC Address................................... b8:62:1f:e9:9f:30
    Client State..................................... Associated    
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 7 
    BSSID............................................ b8:62:1f:e9:9f:31 
    Connected For ................................... 105 secs
    Channel.......................................... 11
    IP Address....................................... 10.6.2.160
    Association Id................................... 8 
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1 
    Status Code...................................... 0 
    Session Timeout.................................. 65535
    Client CCX version............................... No CCX support
    QoS Level........................................ Silver
    Diff Serv Code Point (DSCP)...................... disabled
    802.1P Priority Tag.............................. disabled
    WMM Support...................................... Enabled
    U-APSD Support................................... Disabled
    Power Save....................................... OFF
    Current Rate..................................... m7
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ Yes
    Policy Manager State............................. RUN
    Policy Manager Rule Created...................... Yes
    ACL Name......................................... none
    ACL Applied Status............................... Unavailable
    Policy Type...................................... N/A
    Encryption Cipher................................ None
    Management Frame Protection...................... No
    EAP Type......................................... Unknown
    Interface........................................ students
    VLAN............................................. 15
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 15
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 1
          Fast BSS Transition........................ Not implemented
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 36509
          Number of Bytes Sent....................... 32902
          Number of Packets Received................. 300
          Number of Packets Sent..................... 66
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of Data Retries..................... 95
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 1
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -66 dBm
          Signal to Noise Ratio...................... 29 dB
    Nearby AP Statistics:
          APSOEBFF_COR3(slot 0) .....................
    antenna0: 50 seconds ago -91 dBm................. antenna1: 50 seconds ago -76 dBm
          APSOEAFF_FAC(slot 0) ......................
    antenna0: 108 seconds ago -89 dBm................ antenna1: 108 seconds ago -87 dBm
          APSOEBGF_FAC(slot 0) ......................
    antenna0: 50 seconds ago -82 dBm................. antenna1: 50 seconds ago -71 dBm
          APSOEBGF_STAFF(slot 0) ....................
    antenna0: 49 seconds ago -74 dBm................. antenna1: 49 seconds ago -58 dBm
    WLAN config
    WLAN Identifier.................................. 9
    Profile Name..................................... STAFF
    Network Name (SSID).............................. STAFF
    Status........................................... Enabled
    MAC Filtering.................................... Enabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      NAC-State...................................... Disabled
      Quarantine VLAN................................ 0
    Number of Active Clients......................... 32
    Exclusionlist.................................... Disabled
    Session Timeout.................................. Infinity
    CHD per WLAN..................................... Disabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ staff
    WLAN ACL......................................... unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Quality of Service............................... Silver (best effort)
    Scan Defer Priority.............................. 5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    IPv6 Support..................................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Disabled
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       H-REAP Local Switching........................ Disabled
       H-REAP Learn IP Address....................... Enabled
       Infrastructure MFP protection................. Enabled (Global Infrastructure MFP Disabled)
       Client MFP.................................... Optional but inactive (WPA2 not configured)
       Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    HELPPPP!

    We have 75 evenly distributed AP's servicing the 500 odd users. Found the below traps on WLC. I was making some changes in the WLAN settings at the time:
    Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:8c:a9:82:5d:d2:dc Base Radio MAC :3c:ce:73:c6:fe:00 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    106          Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:58:94:6b:f2:24:c8 Base Radio MAC :c8:f9:f9:4c:01:30 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    107          Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:bc:77:37:72:dc:0b Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    108          Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:00:26:c7:7d:12:76 Base Radio MAC :3c:ce:73:c4:79:80 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    109          Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:bc:77:37:75:1f:93 Base Radio MAC :c8:f9:f9:2b:85:30 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    110          Tue Apr 16 00:03:45 2013          Client Excluded: MACAddress:ac:72:89:58:8e:b9 Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    111          Tue Apr 16 00:03:44 2013          Client Excluded: MACAddress:bc:77:37:26:cd:e3 Base Radio MAC :3c:ce:73:c5:1f:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    112          Tue Apr 16 00:03:44 2013          Client Excluded: MACAddress:ac:72:89:25:ea:e0 Base Radio MAC :3c:ce:73:c6:77:70 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    113          Tue Apr 16 00:03:44 2013          Client Excluded: MACAddress:00:24:2c:6a:85:3d Base Radio MAC :3c:ce:73:c6:6a:50 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    114          Tue Apr 16 00:03:44 2013          Client Excluded: MACAddress:68:5d:43:61:16:51 Base Radio MAC :3c:ce:73:f6:0c:20 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
    115          Tue Apr 16 00:03:44 2013          Client Excluded: MACAddress:7c:d1:c3:8a:64:f6 Base Radio MAC :3c:ce:73:c4:74:20 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2

  • Transferred calls are dropped after CNA timeout

    I have a problem I just can't find the answer to. I am certain tha the answer would be easy, but right now, I'm lost.
    Here is a quick description of the problem (CCM 4.1.3 btw.)
    If a call to DN 1111 in partition X is not answered (internal and external), it is redirected to the operator at DN 3001 in partition Y.
    However, if a call to DN 2222 is answered, then manually transfered to DN 1111 and not answered. The call is dropped (and a busy signal is issued) when it is supposed to redirect to DN 3001.
    The strange thing is: if I but the DN 3001 in partition X (Same as DN 1111), the redirection works.
    Short summary: When a direct inbound call to any DN is timed out and then redirected to another DN. It works.
    When a call has been transfered to a DN, and then is timed out. Redirection is only successfull within the "current" partition.
    Which CSS is used when a call is transfered, and then redirected (timed out). It is clear to me, that it does not use the CSS defined in line-config of the phone.
    Any good answers?
    Kind Regards
    Lasse

    Yes it is. I will try to clearify the issue:
    If I dial an internal DN (DN 2003 dials DN 2004 in partition X)), and the dialled party does not pick up the phone. The line is confgured to FWD No Answer Internal (and eksternal) to DN 3001 (in partition Y) using a CSS with partition Y in it. There is nothing wrong with this scenario, and the call is forwarded to the swichboard as designed.
    But if DN 2001 calls DN 2002 and the user at DN 2002 manually transfer the call to DN 2003 (and complets the transfer without waiting for DN 2003 to pick up the call), the FWD No Answer Internal (and eksternal) to DN 3001 fails. The same rule is applied, but gets disconnected when beeing transfered to a different partition. If DN 3001 is put in partition X (with DN 200X) the FWD No Answer Internal (and eksternal) to DN 3001 works just fine.

  • E4200 - constantly getting drop wireless connection

    First, if you only plan on using the ports on the back for network connections, I have had no problems. My issues are all deal with the wireless connections. I am constantly getting dropped and when I called Cisco/Linksys support, I was told that I needed to turn off my wireless N and have all the devices connect at a slower speed.

    First of all please verify that you have got a 802.11n card in your computer. New generation routers (i.e. E4200) speaks an entirely different language than 802.11g cards, so while those adapters can work with the E4200 for example, they are not optimized to work with it. It is like having to translate from one language to another in real time when going from N to G... So in those cases the old router will show a stronger signal than the new one.
    SECOND, make sure the adapter driver is up to date.
    Try to do the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
              1] Open the software and go to the option which says "Router Settings"
              2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
             3] Then go to the Wireless tab, keep network mode as mixed,
     For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
     For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

Maybe you are looking for

  • Unit testing and integration testing

    hello 2 all,                 what is the diff bet unit and integration testing? in sap what is unit teesting consists of and integration testing consists of what? is this the work  of test engineers r whose work is this? take care love ur parents

  • Not recognizing wireless keyboard/trackpad/mouse

    Just installed windows 7 on new 2012 imac.  loaded the support software. still not recognizing the mac's wireless keyboard, trackpad, or mouse.  what should I try??

  • Tecra P5 - Volume control doesnt work properly

    Hi Since upgrade to Windows 7 64 bit I can't turn the volume all the way down by using the volume control at the front of the notebook. Worked fine under Vista 32 bit. The volume control still works but no matter how far I wind it to the left there i

  • AE 5.2 and CC 5.2

    Hello, What happens when an SOD check is run in Access Enforcer for a request that contain role in AE but that doesn't appear in Compliance Calibrator ? I'm thinking AE will not run Sod for that particular role..any suggestions pls..

  • My keyboard is stuck on English (US). Plz help!

    My iPad keyboard won't change to British English, so the dictionary is always American. The keyboard can be any other language, it's just when I select English it always stays on English (US). Please help.